Removing Flex Stack Configuration from a removed member

Hi all
I'm pretty new to Felx Stack.I tried to stack 4 C2960-48TDL switches.All four switches were configured seperatley with different Managment IPs(192.168.172.11/12/13/14) before
stacking.And The highest Up time switch became the master as expected and stack was accessble(SSH) via the managment IP(192.168.172.11) of that partcular switch.All went well up to that.
But when i removed the 4th member(original managment IP wa 192.168.172.14) of the stack from stack i needed it(4th Member) to fall back to its initial config and to acess via its managment IP(192.168.172.14).But it was still stuck with stack config and was not able acces(SSH)s via the 192.168.172.14 IP.even couldn't
acess via the IP of 192.168172.11 and even Host name was showing as the master switch.Can some one please help me with this...?
Thanks in Advance.
Pramod

What you are seeing is a normal behaviour.
Stacking means the rest of the member switches SHARE THE SAME CONFIGURATION with the stack master. All the configurations of switch 2, 3 and 4 were overwritten with the configuration from switch stack master 1.
Look at the way the interfaces are named/numbered at the switches removed from the stack.
You will need to run the command "switch renumber " and reload.

Similar Messages

Will completly removing itunes and quictime from computer remove the songs?

title says it all i need to know becaus itunes and quicktime is being really stupid because i cannont update to itunes 7 due to quicktime and some Hkeylocal service error and now whenever i plug in my i pod to the computer itunes keeps saying that the software wasnt installed correctly and i have to reinstall it which i did numerouse times i have looked and searched the wholeforums to make this work i want to completely remove it from my computer like it never existed and maybe i can get i tunes back with itunes 7, but im afraid of losing all my songs off the computer but if it did will i still be able to get my purchased songs back?
Windows XP

Hey Ferrari360gt,
This article: http://docs.info.apple.com/article.html?artnum=93976 will give you some good tips on uninstalling and reinstallling iTunes and Quicktime.
Jason

3750x Stack UTIL-3-TREE: Data structure error--attempt to remove an unthreaded node from a tree

A Cisco Stack 3750X switch report the following error message:
%UTIL-3-TREE: Data structure error--attempt to remove an unthreaded node from a tree.
every minute +-20 sec
Cisco IOS Software, C3750E Software (C3750E-IPBASEK9-M), Version 15.0(2)SE4, RELEASE SOFTWARE (fc1)
analog bug: https://tools.cisco.com/bugsearch/bug/CSCsz93221

WS-C3750G-24PS-E C3750-IPBASEK9-M version 12.2(53)SE2
After implementing 802.1x with Avaya IP phones
%UTIL-3-TREE: Data structure error--attempt to remove an unthreaded node from a tree
Port then fails authentication and goes into vl-err-dis

Removing Stacked Images from Book Browser

How do you remove (delete) stacked images for the browser when you are making a book? With a single image I can just select the image and hit delete, but when I select an image that is in a stack it won't allow me to delete it from the browser.
Just to be clear, I'm not trying to delete the images from my library, I'm just trying to remove them from the browser of a book project.
thx.

I did it by extracting from the stack, the image I wanted in the book. Then I could delete the remaining images in the stack.

If I remove a stack from the dock where do the files go?

I have numerous files and folders in the Documents stack. I really don't need to see most of those files. If I remove the Documents stack form the Dock will I lose the files? Where will they be?
Thanks

So, I'm new to Macs, but if I understand correctly, I could click on the Macintosh HD icon, then go to Users and then to my folder, once there I can create a new folder and put my commonly updated files in there. Then I could remove the Documents folder from the Dock and I should have what I want: frequently updated files in a stack on the dock and less frequently used files/folders still in my folder (ie the Home folder) which would be accessible through the Finder.
Right??
Thanks

How do I remove stacked photos from my desktop

How do I remove stacked photos from my MacBook Pro desktop?

Hi there JudyComeaux,
If you are would like to re-arrange your the items on your desktop so they aren't stacked on top of each other, take a look at the information below.
Mac 101: The menu bar
http://support.apple.com/kb/HT2473
Cleaning your desktop
To help get you familiar with how menus and menu commands work, here's how to clean up your desktop using Finder menu commands.
To tidy up your files and folders so that they all line up in nice, neat rows, click on the desktop to make the Finder active.
From the View menu, choose Clean Up.
If you want to organize files and folders by name, kind, or other criteria do this: From the View menu, choose Arrange By, then choose Name or Kind or another choice in the submenu.
If you need to remove those files, take a look at the article below.
OS X Mavericks: Remove files and folders from your Mac
http://support.apple.com/kb/PH13765
-Griff W.

Best way to remove CSM configuration from a switch

have a redundant pair of CSM , would like to move slave CSM to a new switch, what is quickest way to eliminate all configuration from this switch so the same can be installed on the new switch , without reloading the switch or causing any downtime to already existing connections through the master CSM.

HI Imre,
Kindly read the following section for the required :
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/csm/4.2.x/configuration/guide/redun.html#wp1047388

Complete Removal of Stream Configuration in 9.2

Could any one send me the script for complete removal of streams configuration in oracle 9i database. I faces a lot of error while creating stream configuration.

Hi,
Agree with Willard Martin. If you want to a DAG member, you need to remove database copies first, then you can remove the Mailbox Server from the DAG.
Here is a related article for your reference. Even though this article is for Exchange 2013, it also applies to Exchange 2010.
http://exchangeserverpro.com/exchange-2013-how-to-remove-dag-member/
Best regards,
Belinda Ma
TechNet Community Support

How to remove credit card info from ipod??

i need to remove my credit card info from another ipod from a family member??

You can (maybe) remove your credit crd data from your iTunes account:
How To
All of your account information can be changed from the Apple Account Information page. To get to the Apple Account Information page, follow these instructions:
Open iTunes.
Choose Store > Sign In.
Enter your Apple ID and password, then click the Sign In button.
Choose Store > View My Account.
Enter your account password and click the View Account button.
To update your name, billing address, or payment information, follow these instructions:
From the Apple Account Information page, click the Edit Payment Information button.
Edit the information that you would like to change.Note: The payment methods that the iTunes Store accepts can be found in the payment type section. If you do not want a payment method on your account, select None in the payment type section.
Click the Done button once you have updated all of your information.
You can also sign out of the iTunes account on the the iPod. Go to Settings>Store and sign out.

How can I remove the 'Qty' text from individual product descriptions?

I didn't know if this was possible or not... I've recently taken the reins of handling an ecommerce site that had been published before I got on board. My boss wants me to remove the 'Qty:' description from some products because the image shown for some products is a misleading description of the actual quantity available (i.e. there is a picture that shows a stack of conveyors parts, and it says 'Qty: 1' to represent one 'stack' of conveyor parts - this confuses customers into thinking there's only one individual conveyor part available however). To avoid any confusion he requested that I remove the 'Qty' text from similar images. I see that you can change the 'In Stock' amount of a particular product underneath the 'Inventory' tab of the 'Products' menu, but I didn't know if it was possible just to remove the quantity description altogether without just typing the quantity in at zero. This is likely a strange question but I didn't know where else to ask! I would appreciate any help or advice Thank you

Hi ewhelhalu,
I just figured out a way to do it, but it's a little weird and complex, and I have no idea what the consequences for editing this .plist string might be. I'm thinking it'll be OK, but you never know what might happen when you screw around with Apple's intentions.
So if you have the Developer Tools on your install of OS X, you can use the Property List Editor to edit the Dock files. (If you don't have this program, you can use a program like [Pacifist|http://www.charlessoft.com> to selectively install stuff from your Leopard disk).
The file you're interested in is within Macintosh HD > Users > Your Username > Library > Preferences, and it's called com.apple.dock.plist. Open that up with Property List Editor, and open the arrow drop-down next to "Root." The lines you're looking for are "persistent-apps" (the left side of your Dock) and "persistent-others" (the right side). If you open the drop-down arrows, you'll see there are numbers below each. The numbers correspond to your Dock items, from left to right.
If you click on drop-arrows by the numbers, a sample hierarchy looks like this: 0 > tile-data > file-label. It's the "file-label" string that you want to edit. Just make it ("it" being the name of the icon under the "value" column) blank, save the file, go into Terminal and type "killall Dock" without the quotes, and your Dock icon should appear without a name. You'll have to do this for all of them.
I should insert the usual caveats here about backing up beforehand and making sure that you have a copy of the .plist file before you start tweaking it so that you can replace it if things go wrong. And perhaps someone with more knowledge of Terminal or third-party apps than I have will come along and suggest a simpler solution. But that's the only one I have.
Hope that helps!
—Hazy

How can I remove the " Source.vi" from long Express VI Names?

I am in the Moment working on the Development of an Express VI
library for test purposes.
How can I remove the " Source.vi" from long Express VI Names?
This happens when the Express VI is inserted in the blockdiagram
and listed in LabVIEW and TestStand Palettes.
By short names like "DAQ-Assistent" or "EasyCalc" the string " Source.vi"
is not shown at the end of the Express VI names.
I used The Express VI Dev Toolkit 1.0 to create the Express VIs.
Labview Version: 7.1 Base
TestStand: 3.1
It would be great to get the expert advice from the Forum for this issue!
Thanks a lot.
Andre

I think I understand what you are asking for. If I am wrong, please try to explain it a bit more.
The name shown may be different than the name of the vi file. To do this, your source VI and popup on its icon. From the short menu that comes up, select VI properties. In the top ring, select Window Appearance. The page that comes up lets you set various things that can affect the appearance of the VI. What you want to change is the window title. Uncheck the Same as VI name checkbox and change the string to whatever you want it to be.
I hope that this helps,
Bob
Bob Young - Test Engineer - Lapsed Certified LabVIEW Developer
DISTek Integration, Inc. - NI Alliance Member
mailto:[email protected]

Want to remove Technical data Tab from Work Center

Hi All,
I want to remove Technical data Tab from Work Center. I have Removed ''Technical data'' Tab from Plant Maintenance and Customer Service-->Master Data in Plant Maintenance and Customer Service -->Maintenance Plans, Work Centers, Task Lists and PRTs >Work Centers>Configure Screen Sequence for Work Center.
Still I am able to see Technical Data Tab in IR01, Work center.
Is there any other config to remove the same?

This is resolved.
I have changed the config in following node as 0005 for PM
SPRO / IMG -> Plant Maintenance and Customer Service -> Master Data in Plant Maintenance and Customer Service -> Maintenance Plans, Work Centers, Task Lists and PRTs -> Work Centers->General Data->Define Work Center Types and Link to Task List Application

Problem removing bluetooth stack / hidden devices / COM ports not released

Hi
Having problem completely removing Toshiba Bluetooth stack / hidden devices / com ports not released
I uninstalled Toshiba BT s/w...
But:
1) Toshiba BT hidden devices still appear and I can not remove (get error)
2) COM ports occupied by Toshiba BT not released (so they cannot be used by another BT stack) and still appear in registry
ex: friendly name Toshiba BT Port (COM4) still in registry
3) These unreleased com ports do NOT appear in device manager
Thanks

It seems that you still have some configurations which were not removed during the uninstallation.
This means that the resources can not be release, because those are still necessary in case of a
new installation of the stack.
The first I would try is the following:
- Install the latest Toshiba Bluetooth stack.
- Uninstall it. Ensure that you answer all questions with "yes" ! This means also the one which asks if all configurations should be removed.
- Reboot
- Check again

[svn:fx-trunk] 12883: Remove the skin classes from the halo theme project to avoid redundancy with the airframework /framework swcs.

Revision: 12883
Revision: 12883
Author:   [email protected]
Date:     2009-12-12 15:53:50 -0800 (Sat, 12 Dec 2009)
Log Message:
Remove the skin classes from the halo theme project to avoid redundancy with the airframework/framework swcs.
QE notes: No
Doc notes: No
Bugs: SDK-24293
Reviewer: Glenn
Tests run: Checkintests, smattering of Halo and AIR mustella tests
Is noteworthy for integration: Yes
Ticket Links:
    http://bugs.adobe.com/jira/browse/SDK-24293
Modified Paths:
    flex/sdk/trunk/frameworks/projects/framework/src/FrameworkClasses.as
    flex/sdk/trunk/frameworks/projects/halo/build.xml
Added Paths:
    flex/sdk/trunk/frameworks/projects/framework/src/mx/skins/halo/WindowBackground.as
Removed Paths:
    flex/sdk/trunk/frameworks/projects/halo/assets/
    flex/sdk/trunk/frameworks/projects/halo/src/HaloClasses.as
    flex/sdk/trunk/frameworks/projects/halo/src/mx/skins/

Remove mailbox database copy from DAG

Hi There,
We would like to remove the mailbox database copy from our exchange server as we are lack of the space on our fixed vhd and we hope to be able to free about 100GB from the passive database copies as we have deployed DAG. is there any guidelines or procedures
to safely remove the database copies? currently, we have 4 mailbox servers, HQMB01, HQMB02, SSMB01, and SSMB02. HQMB01 and HQMB02 is already part of DAG members by itself. however, on ssmb01 and ssmb02, we also add in HQMB01 and HQMB02 as the DAG member,
thus they can fail over to HQMB01 or HQMB02 if their server have issue. in this situation, SSMB01 and SSMB02 passive copies is also inside our HQMB01 and HQMB02. As the our HQMB01 and HQMB02 is lack of the disk space and we would like to remove SSMB01
and SSMB02 from the DAG, thus we could remove the passive database copies. The following is the picture of the activation preference for all servers. what is the procedures and the guidelines to remove mailbox database copy and also remove the server from
the DAG members? we are quite confuse and worry that after we are removing wrongly and cause the active database to lost as we understand that there is replication happening between them. as we have 4 mailbox servers from which server we should perform
the task? Wish to get some advises from the exchange guru from this forum. we are on exchange server 2010 sp1 and windows server 2008 R2.Thanks so much.
Name                 : HQDB01
Servers              : {HQMB01, HQMB02}
ActivationPreference : {[HQMB01, 1], [HQMB02, 2]}
ReplayLagTimes       : {[HQMB01, 00:00:00], [HQMB02, 00:00:00]}
TruncationLagTimes   : {[HQMB01, 00:00:00], [HQMB02, 00:00:00]}
Name                 : HQDB02
Servers              : {HQMB02, HQMB01}
ActivationPreference : {[HQMB02, 1], [HQMB01, 2]}
ReplayLagTimes       : {[HQMB02, 00:00:00], [HQMB01, 00:00:00]}
TruncationLagTimes   : {[HQMB02, 00:00:00], [HQMB01, 00:00:00]}
Name                 : SSDB01
Servers              : {SSMB01, SSMB02, HQMB01, HQMB02}
ActivationPreference : {[SSMB01, 1], [SSMB02, 2], [HQMB01, 3], [HQMB02, 4]}
ReplayLagTimes       : {[SSMB01, 00:00:00], [SSMB02, 00:00:00], [HQMB01, 00:00:00], [HQMB02, 00:00:00]}
TruncationLagTimes   : {[SSMB01, 00:00:00], [SSMB02, 00:00:00], [HQMB01, 00:00:00], [HQMB02, 00:00:00]}
Name                 : SSDB02
Servers              : {SSMB02, SSMB01, HQMB01, HQMB02}
ActivationPreference : {[SSMB02, 1], [SSMB01, 2], [HQMB01, 3], [HQMB02, 4]}
ReplayLagTimes       : {[SSMB02, 00:00:00], [SSMB01, 00:00:00], [HQMB01, 00:00:00], [HQMB02, 00:00:00]}
TruncationLagTimes   : {[SSMB02, 00:00:00], [SSMB01, 00:00:00], [HQMB01, 00:00:00], [HQMB02, 00:00:00]}

Hi Exchange Guru,
thanks so much for the prompt response..i have few queries to ask following your guidelines above:
1. from the show result above, I am still confuse which server that I should go to remove as this is involving 4 database copies. from what I understand from the truncation or replay lag times of SSDB01 and SSDB02, I can see that HQMB01 and HQMB02 are on
the third and fourth preference, which means that SSDB01 and SSDB02 will be able to failover to each of them when there is a failure and it cause the passive copies of both of SSDB01 and SSDB02 to be stored in the HQMB01 and HQMB02. what my purpose
is to remove both SSDB01 and SSDB02 passive copies in HQMB01 and HQMB02. in this case, should I login to SSDB01 or SSDB02 mailbox servers to perform the removal with your guidelines above?
2. is the command as below:
Remove-MailboxDatabaseCopy -Identity SSDB01\HQMB01 -Confirm:$False
Remove-MailboxDatabaseCopy -Identity SSDB01HQMB02 -Confirm:$False
Remove-MailboxDatabaseCopy -Identity SSDB02\HQMB01 -Confirm:$False
Remove-MailboxDatabaseCopy -Identity SSDB02\HQMB02 -Confirm:$False
will this cause the risk either of my HQDB01, HQDB02, SSDB01, and SSDB02 active copies accidentally being removed? I am sorry that I am a bit naggy and always want a confirmation as this is very critical and I must be super careful.
3. If after the removal successful, when is the best time to go to the drive where the passive copies stored and remove them so I can clear some space on my disk? and is it just as simple by going to the drive and do a folder file deletion manually?
because I just worry when I delete the file and the server is still replicating between each other, which will cause even corruption to the active database.
4. From point 3, you mention about when the server is empty. what do you mean by that? do you mean that when the passive copies are no more there? and what command that I used to check?
5. From point 4, is removing the server from DAG the last step to be performed? yes, I want to remove them from DAG, thus will left only HQMB01 and HQMB02 as one DAG and SSMB01 and SSMB02 as one DAG.
Thank so so much for your patient and attention.
Regards,
Henry

Removing Flex Stack Configuration from a removed member

Similar Messages

Maybe you are looking for