Route master configuration

Dear Friends
i need some guidance as to how to configure route master in SAP to calculate the freight in a PO automatically. this is a completely new area for me and any doc to help out on the issue would be really welcome and appreciated
regards
gurvinder

show phy
show circuit
verify that status of the physical link.
show arp
make sure you have aro entries for the servers and gateways.
Finally, if you are reusing the same ip addresses, make sure to clear the arp table of the servers and gateways.
Regards,
Gilles.

Similar Messages

Route TCPS01 is not maintained in route master

Hi Gurus,
At VT01N level, I fail to understand what this message or error from the system means:
"Route TCPS01 is not maintained in route master"
Can anyone help me solve the problem?
Thanks
regards
Chris

Hello Chris,
Route TCPS01 needs to be maintained in TVRO table.
Following customization settings are required for this route determination;
SPRO>>Logistics Execution>>Transporation>>Basic Transportation>>Routes>>Define Routes EVery point has to be configured and determined.
SPRO>>Logistics Execution>>Transporation>>Basic Transportation>>Route determination
SPRO>>Logistics Execution>>Transporation>>Basic Transportation>>Route Schedule Determination
Following SAP documentation will also be useful
http://help.sap.com/saphelp_46c/helpdata/en/dd/5607da545a11d1a7020000e829fd11/content.htm
Br,
Tushar

Problem with Updating of Routing Master data

Hi,
    My requirement is I have to download Routing Master data into excel sheet. Once downloading is over, user can change some fields data in excel sheet. Again ull upload the changed excel sheet data to SAP. Finally these changes will effect to the Routing Master data.
I am downloaded routing master data using FM CARO_ROUTING_READ.
I changed some fields in excel sheet. I tried so many FMs for updating the routing master data, but system not allow to me to change the Master data.
I tried with CP_BD_DIRECT_INPUT_PLAN,
             CP_BD_DIRECT_INPUT_PLAN_EXT,
             CP_BT_PLPO_UPDATE, for updating Routing Master.
And Standard program RCPTRA02 also.
Please send me one function module which can update the Routing Master data. But that FM have the same structure of CARO_ROUTING_READ. Otherwise type conflicts will come.
System throws error YOU CANNOT EDIT TASK LIST OBJECTS WITH ACTIVITY TYPE&.
Regards
Shaik

Hi,
I have found in OSS the following programs to download and upload routings:
- Note 107242: You can create the sequential input file with report RCPDIRO1
- Note 106965: Direct input routings: reading datasets
Maybe this can help you to upload your routings in another way. Unfortunately I haven't figured out yet how the program exactly works. So if somebody can give me some info about that one, it would be great.
Thanks,
Steve

Routing for configurable material

Hello PP gurs,
I want to create Routing for Configurable Material in SAP PP-PI or PP industries. How the object dependency is defined applied ?
This requirement is for Make TO Order scenario for Configurable Material.
At present I am working with resources only.
I want to create in such away So that while creating Production order system should ask select BOM & routing.
How can I define the Super BOM & Super Routing in Order?
Is it possible to calculate cost for this kind of requirement?
Please Give your Contribution from Whatever the Questions above....
Thanks & Regards,
Bhavik Dangi.

Dear,
In can explain youn w/ example
Let us say you have to manufactur CAR's(matyerial no in SAP is CAR). The coonfiguration options are - Paint, and tyre
Create a char inn CT04 as piant and tyre with value as below(data type = char)
Paint - white, red, blue and black
Tyre - Redial, Normal
Create materials like White-paint, Red-paint, Blue-paint, black-paint, Tyre-redial, tyre-Normal, Engine
Create a class in CL01 called CAR-CLASS , clas type 300 and assign the above Char to this class
Assign this class to Material CAR.
Create BOm with following items
Engine
White-paint
RED paint
Blue-paint,
black-paint,
Tyre-redial,
tyre-Normal,
Create a object dependency in CU40 type - selcetion condition to selcet red-paint material when in Sales order select paint red. and like this all others.
Selection condition for red paint is as below
Paint = 'red'
Like this for all others
Paint = 'white'
Paint = 'black'
Paint = 'blue'
Tyre = 'Normal'
Tyre = 'Redial'
Assign this object dependency to BOm items
Engine
White-paint -
>Paint = 'white'
RED paint -
>Paint = 'red'
Blue-paint, -
>Paint = 'blue'
black-paint, -
>Paint = 'black'
Tyre-redial, -
>Tyre = 'Redial'
tyre-Normal---->Tyre = 'Normal'
Now create a configuration profile
When you create a Sales order, system will pronmpt to enter the vlaues for piant and tyre
if you have selceted piant as red and tyre as normal, then the BOm will look like as below
Engine
RED paint
tyre-Normal
This is the configured BOM...what you have cretaed is supre BOM.
It is available in PP
For nmore information see blow
http://help.sap.com/saphelp_47x200/helpdata/en/92/58d455417011d189ec0000e81ddfac/frameset.htm

CRM Email Router & Email Configuration

Hi All,
I have some question related email router & email configuration in MS CRM 2015. I test using gmail account for both CRM email and contact email (different gmail account).
1. I try send from my gmail to CRM directly, the result is the email not received in CRM. but if I try from CRM to my gmail using email activities first, after email received in my gmail inbox and reply back the email, I have received new email activities
in CRM. my question is why the email not received if I try to send directly?
2. what is email server profile use for? is there any article/link is easy to understand?
thanks.

hi Erro,
why I asked is to check if email router machine account is added into the priv user group.
http://msdn.microsoft.com/en-us/library/hh550195(v=crm.6).aspx
regards
Jithesh

Overlapping and splitting in routing master.

Hi...
I'm setting the PP routing master and using the capacity requirement planning.
Do you have any definition or document about the overlapping and splitting in routing master ?
In part of overlapping. There are the options
- Required overlapping, Optional overlapping, Continuous flow prod
Could you please explain how does the system calculate the lead time in production when I use the different option together with Min.overlap time or Min. send-ahead qty ?
Best Regards
JN

Hi,
Refer the SAP help given below it comes with an example & should clarify your query
http://help.sap.com/erp2005_ehp_04/helpdata/EN/8b/67221404f111d293560000e8323492/content.htm
Regards,
Vivek

Need a java code using swing that can do master configuration

I need a java code using swing that can do master configuration.For example, in the 1st screen it will show all configuration checke boxes . According to those selected check box, it will show the needed panels sequentially and finnaly it will update many xml files.

TapasB wrote:
I need a java code .......and I wish you much luck in creating it. Please come back if you have a specific question on a specific part of your code that is not working quite right.

Please specify Transaction code to load SCM ROUTE MASTER DATA (EWM Routes)

Please specify Transaction code to load SCM ROUTE MASTER DATA (EWM Routes data).
Regards
Dhirendra
Moderator message - Moved to correct forum
Edited by: Rob Burbank on Apr 21, 2009 8:58 AM

Route definition is done at 0VTC. You have define the Route with its description, Transit time, factory calender, carrier info etc. It is stored in TVRO table
Then yoiu will maintain the route determination in 0VRF.
Route Determination:
Dep zone of the shipping point + Destination zone (T-zone) of the ship-to + Transportation group + shipping conditions.
Route determination details are stored in TROLZ table.

Problem with Cisco 3250 mobile router WMIC configuration

I have two 3250 mobile routers, and each one has 2 WMICs, 1 MARC and 1 4-port FEMIC. WIC1 seems to be the AP since its FE port connects to the FE0/0 or MARC, and WIC2 seems to be the bridge since its FE0 connects to FEMIC's FE2/3. The IOS version of router is 12.4(2)T3, and IOS version of both WMIC is 12.2(15).
I configured two routers in the following way (similar configuration as the police car example in the 3200 router software configuration guide):
1. Router1's WIC2 (bridge) acts as WGB, and router2's WIC2 (bridge) acts as root bridge.
2. Router2 is the DHCP server also.
3. WIC1 of each router is configured as root AP.
During my testing, the following scenarios happened:
1. WIC2 of both router can successfully associated.
2. Wired client can get IP address from router2 when it is pluged into either router's FE ports.
3. Wirless client can associate with the bridge connection, i.e. connected to the wirless bridge connection. (Weired! Can bridge work as a AP?)
4. Wireless client can't stably associate with WIC1 of either router, which is supposed to work as AP. A lot of authentication and deauthentication messages are flushing in the console. IP address can be leased, however, Ping was not successful.
My question is:
1. Why did this kind of problem happen?
2. How should i configure each WIC to achieve the set up of wireless client associate with AP and routers communicate through bridge?
3. Is my understanding on 3200 router wrong?
Thanks a lot for reply!

Hello,
i have the same problem with router CISCO861W-GN-E-K9. Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Can someone help?
Thank you.
Here is my config for internal AP and router.

Router is configured; Windows XP desktop cannot get a full conneciton...

I recently reinstalled my XP desktop because it was acting strange and did the same with my wireless adaptor. I am sure that my wireless router is configured correctly, however I have typed in all in athetificaiton information for the adaptor and now I am getting the message "validating indetiy". Any reason why I should be getting this? I cannot get the status to change no matter what I do, even reinstalling will not change it.
Any help would be appreciated.
Brad Tway

Go to the router's setup page. Disable wireless security and try the connection. Re-enable it afterwards.

Customer master configuration

Hi all,
I am looking for material related to customer master configurtion.
Can anybody provide me the relavant material which may give
sufficient idea about customer master configuration step by step.
regards.

Hi Azra,
Check this http://help.sap.com/saphelp_470/helpdata/en/01/a9b288455711d182b40000e829fbfe/frameset.htm
Regards,
Pankaj

CSS virtual-router master/master problem

Dear all experts,
I have two CSSs 11150 and have configured them as following:
CSS-1#
circuit VLAN100
ip address 172.10.10.101 255.255.255.0
    ip virtual-router 1 priority 105 preempt
    ip redundant-vip 1 172.10.10.1
    ip critical-service 1 up_down_stream
    no redirects
CSS-2#
circuit VLAN100
ip address 172.10.10.102 255.255.255.0
    ip virtual-router 1 priority 101 preempt
    ip redundant-vip 1 172.10.10.1
    ip critical-service 1 up_down_stream
    no redirects
Here is my connection:
CSS-1 <=> Switch <=> CSS-2
They were working fine before but CSS-2 suddenly change to master few days ago. I have already checked the connection between these two CSSs and it seems ok, so I tried to capture the packet trace both for the ports connected to CSS-1 and CSS-2 from the switch. And finally I found that I can see the vrrp adv. message which send from CSS-2 at the port which is monitoring CSS-1, but there is no vrrp adv. message send from CSS-1. I am not sure the problem is related to the acl as it has configured to permit any any:
clause 254 permit any any destination any
Could anyone can help me in this case? Is the problem related to the keyword "preempt" in CSS-2? Is it a software bugs which hasn't listed in cisco bug list (SW Version: 6.10)?
Thanks!

Hi,
I'm not sure if this you've resolved this problem; however, from what I have read you should never configure the preempt option on the same virtual router on both CSSs.
The issue of both CSSs becoming master when using the preempt option is highlighted in this guide:
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11000series/v5.00/command/reference/CmdCirIP.html#wp1027189
I have used the preempt option to failover to the backup CSS in the past; however, to achieve this the preempt option had to be removed from the existing master.
I hope this helps.
Thanks,
C

Cisco asa 5505 with Router 881w Configuration Help

Hello all,
I'm having trouble setting up a second vlan to route to the internet. I have a Cisco ASA 5505 connected to my ISP(OUTSIDE) and a Cisco 881w (INSIDE) router in the back of my firewall. My vlan 10 with the network 192.168.5.1 255.255.255.0 works with pat, however vlan 15 that is on my 881w router does not route to the internet at all. I can only ping from 192.168.15.15 network to 192.168.5.1 I would like some advice on how can I make this set up work. Attached with this discussion is a picture of my topology.
Thanks in advance.
here are the show runs:
Cisco ASA 5505 show run:
ASA Version 8.3(1)
names
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan5
mac-address xxxx.xxxx.xxxx
nameif OUTSIDE
security-level 0
ip address dhcp setroute
interface Vlan10
nameif INSIDE
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 5
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object network INTERNAL_LAN
subnet 192.168.5.0 255.255.255.0
object network PRIVATE_LAN_192
subnet 192.168.15.0 255.255.255.224
description PRIVATE_LAN_192
access-list INSIDE_access_in extended permit ip any any
access-list INSIDE_access_in extended deny ip any any
access-list OUTSIDE_access_in extended permit ip any any
access-list OUTSIDE_access_in extended deny ip any any
pager lines 24
logging enable
mtu OUTSIDE 1500
mtu INSIDE 1500
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network INTERNAL_LAN
nat (INSIDE,OUTSIDE) dynamic interface
object network PRIVATE_LAN_192
nat (INSIDE,OUTSIDE) dynamic interface
access-group OUTSIDE_access_in in interface OUTSIDE
access-group INSIDE_access_in in interface INSIDE
route INSIDE 192.168.15.0 255.255.255.224 192.168.5.2 1
dynamic-access-policy-record DfltAccessPolicy
http server enable
dhcpd dns 8.8.8.8 75.75.76.76
dhcpd address 192.168.5.10-192.168.5.100 INSIDE
dhcpd enable INSIDE
Router 881w show run:
Current configuration : 4912 bytes
version 12.4
no ip source-route
ip dhcp excluded-address 192.168.15.1 192.168.15.10
ip dhcp pool PRIVATE_LAN
network 192.168.15.0 255.255.255.224
interface FastEthernet0
switchport trunk allowed vlan 1,15,1002-1005
switchport mode trunk
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address 192.168.5.2 255.255.255.0
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
no ip address
interface Vlan15
ip address 192.168.15.1 255.255.255.224
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 FastEthernet4
no ip http server
ip http authentication local
ip http secure-server

The cable modem does not have any configuration. I cant add any to it. Its a cisco dpc3008. From vlan 10 i have no problem to get to the internet with the above configuration. My problem is just vlan 15.

Can't connect to router to configure and setup cd software crashes when ran

I have recently been having a series of blackouts at my appartment. That last one seemed to have messed my router. I tried powering down everything and restarting it. When I do so the lights on the router and my dsl modem light up as usual. The problem is I can't seem to connect to the router via 192.168.1.1. Also, when I run the setup cd the setup software keeps crashing stating Setup Wizard MFC Application has stoped working. I'am on vista ultimate x64. I think my pc is able to connect to the router just that I can't configure it or anything. Any one have any clue on what I could/should do?

Sounds like the firmware might be corrupted. You need to perform a factory reset by holding in the reset button for 30 seconds which is located on back of the router. Wait about 2-3 minutes while the router syncs back up. Try to access the router by typing 192.168.1.1 into IE's address bar. we need to get access so that we can perform a firmware upgrade @ www.linksys.com/download
If all went well and you were able to get the firmware, you will need to perform another factory reset (follow the above).
If you gain access to the router you should write down all your settings as the factory reset will erase all previous settings.
Hope all goes well,
Ttech

I am unable to browse internet from my cisco 881 router and configuration is below could any one help me in this regard

HOME#sho run
Building configuration...
Current configuration : 5657 bytes
! Last configuration change at 10:51:11 UTC Fri May 17 2013 by admin
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HOME
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 $1$bgx9$VrtQW3Wg182VyYhKAHLbN.
no aaa new-model
memory-size iomem 10
crypto pki trustpoint TP-self-signed-1190003239
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1190003239
revocation-check none
rsakeypair TP-self-signed-1190003239
crypto pki certificate chain TP-self-signed-1190003239
certificate self-signed 01
3082024A 308201B3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31313930 30303332 3339301E 170D3133 30353137 31303333
35315A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 31393030
30333233 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100C002 80BBF151 E095E469 AA7DBB18 2A9E3CC2 4AC223F6 ABE0AF49 876C1203
65D0E246 786F174D E5B7897A 44C5755A 2571E58A 184A6C62 DD992A2A D8A24878
25A8D3C3 03F5D3C2 522EC8BB 302B0CCD 2945087A 7AF01418 D0056679 6F64DB4A
BE2D5DA1 106CD03A 83B422A2 3CCBAE88 F2413123 12269390 6949DFE0 411118E7
8F210203 010001A3 72307030 0F060355 1D130101 FF040530 030101FF 301D0603
551D1104 16301482 12484F4D 452E7777 772E7961 686F6F2E 636F6D30 1F060355
1D230418 30168014 3D2D854D 1203F50D 77F4ABC5 B61CEAF6 C922F4DF 301D0603
551D0E04 1604143D 2D854D12 03F50D77 F4ABC5B6 1CEAF6C9 22F4DF30 0D06092A
864886F7 0D010104 05000381 8100B24C 48BACACE 87ADEA03 386F2045 CC89624A
4EB1AD09 062EB2A4 CF4C96CA 0B2CF001 BD2C3804 8DC47FED 6A5B5F0D 3965AC6E
4FC4682F 707E4132 8F27C083 C7FAE1BD 21D055E6 C79D5DAD 051B6321 D35DB4F2
044E6BBD DAD08B6A 6ED87C7E 08F4F7E1 4EFDFB6F 867AF6FA 84165CFC D219D56F
A82EABD4 AD9CFA24 A5088145 E571
        quit
ip source-route
ip routing protocol purge interface
ip dhcp excluded-address 10.10.10.1
ip dhcp pool ccp-pool
   import all
   network 10.10.10.0 255.255.255.248
   default-router 10.10.10.1
   domain-name www.google.com
   dns-server 192.168.1.1
   lease 0 2
ip cef
ip domain name www.yahoo.com
ip name-server 84.235.6.55
ip name-server 84.235.57.230
no ipv6 cef
multilink bundle-name authenticated
license udi pid CISCO881-SEC-K9 sn FCZ1516933C
username admin privilege 15 password 0 cisco
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address dhcp
ip access-group 101 in
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip nat enable
ip virtual-reassembly
ip tcp adjust-mss 1452
interface Vlan2
no ip address
ip nat inside
ip virtual-reassembly
ip default-gateway 192.168.1.1
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 101 interface FastEthernet4 overload
ip route 0.0.0.0 0.0.0.0 FastEthernet4
access-list 23 permit 10.10.10.0 0.0.0.7
access-list 101 permit ip any any
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^C
Cisco Configuration Professional (Cisco CP) is installed on this device.
This feature requires the one-time use of the username "cisco" with the
password "cisco". These default credentials have a privilege level of 15.
YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE
PUBLICLY-KNOWN CREDENTIALS
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want
to use.
IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL
NOT BE ABLE TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
For more information about Cisco CP please follow the instructions in the
QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
^C
banner motd ^Cuthorized ^C
line con 0
login local
no modem enable
line aux 0
line vty 0 4
access-class 23 in
privilege level 15
password cisco
logging synchronous
login local
transport input telnet ssh
scheduler max-task-time 5000
end

HOME#ping 4.2.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 4.2.2.2, timeout is 2 seconds:
Success rate is 0 percent (0/5)
HOME#sh ip int br
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0              unassigned      YES unset down                  down
FastEthernet1              unassigned      YES unset down                  down
FastEthernet2              unassigned      YES unset down                  down
FastEthernet3              unassigned      YES unset down                  down
FastEthernet4              192.168.1.120   YES DHCP   up                    up
NVI0                       10.10.10.1      YES unset up                    up
Vlan1                      10.10.10.1      YES NVRAM down                  down
Vlan2                      unassigned      YES NVRAM down                  down
HOME#
fast ethernet is connected to my internet connection

Route master configuration

Similar Messages

Maybe you are looking for