Route shaping / Route Mapping

Ok I am looking for a way to propoerly force specific traffic over a specific link. I am thinking that I need to dp this with route mapping but am not sure of this is handled by the core or by the edge routers.
Here is the senario. I have two links connected to two different routers and both routers are inturn connected to the same core switch. Link #1 is a 3M serial link and link #2 a 10M Ethernet link. The router supporting the 3M link is a 3825 and the router supporting the 10M link is a 2921. The switch they are connected to is a 3750G.
We have installed two SANs within the network and one is located at the facility supported by these two links. They have started replication between the two SANS and I want to prevent this replication traffic from flowing over the 3M. If the 10M goes down for any reason the replication will be paused or stored until the link comes back up. What do I need to do to advertise / route the traffic between the two SANs over the 10M link? I use EIGRP between the core and the two routers and use BGP between the two routers and my provider. I am thinking the end goal is to not advertise the VLAN the local SAN is attached to over the router with the 3M link attached. Since both routers use the same EIGRP instance if there would be some massaging on both routers or do something unique on the core.
Where do I start? I am working on a refrigerator diagram that shows how things are interconnected and will attach shortly.
Thanks in advancce...
Brent

Hi Brent,
Just make sure the the core has a better metric path to reach the other SAN subnet via the 10M link, Do you want to use the 3 M link as backup - if so the core must see the 3M link is a feasible successor.
You may need to check that the cores at both ends agree on the 10M link as the path between the 2 SANs.
Cheers
Mike

Similar Messages

How to render direction (route) on Elocation Map?

Hi,
I have to build a OAF page where I have the latitude and longitude for source and destination points and when I submit a request from OAF page the Elocation Map should render the driving directions and route on the Map. I have found the following request to Spatial
<?xml version="1.0" standalone="yes"?>
<route_request id="8"
route_preference="shortest"
road_preference="highway"
return_driving_directions="true"
distance_unit="mile"
time_unit="minute"
return_route_geometry="true">
<start_location>
<input_location id="1">
<input_address>
<us_form1 street="1 Oracle Drive" lastline="Nashua, NH" />
</input_address>
</input_location>
</start_location>
<end_location>
<input_location id="2">
<input_address>
<us_form1 street="77 Massachusetts Ave" lastline="cambridge, ma" />
</input_address>
</input_location>
</end_location>
</route_request>
How do I send the same request through my OAF page? Are there APis exposed and what the process?
Thank you,
Prashanth

Probably best to post this on the [FMW MapViewer forum|http://forums.oracle.com/forums/forum.jspa?forumID=727].

Planning a route for HERE Maps/Drive+ Beta

I would like to plan a route with multiple route points in advance and save the planned route to HERE Maps or HERE Drive+ Beta. Is that possible?
The route can be made with here.com webpage, but is it possible to import a route to my Lumia 920? When the route is saved to a collection in my nokia account, it is not shown in the mobile phone.
Phone: Lumia 920
Software: The newest
Solved!
Go to Solution.

Sorry, I'd like to unresolve this. The workaround mentioned is not a solution.
I travel to loads of places by motorcycle, and going off the beaten track is wonderful. Since I upgraded My E6-00 and C7-00 to a Lumia 920, I'm back to allowing the SatNav (phone) to decide where I go. Boring dual carriageways and bypasses are now my natural habitat - bah humbug. Afterall, the phone is in my pocket (safe from weather), headphones in my helmet - I can't constantly look at a map. Having multiple 'favourites' and planning from one to the next isn't workable. Fair enough the Lumia 920 is usable with gloves on (major plus for a biker, come on you marketing people!) but I don't fancy re-routing all the time by the side of a road.
I'm also planning a charity cycle ride over 100s of miles this Summer, and while that can be done in BikeRouteToaster, Google Maps etc, there is no import function into 'HERE' that I can see. It's impossible to plan a route on the device itself. Yes it can route walker (I can't seem to get turn by turn working for that, but nevermind), public transport and car, I have an option to avoid motorways etc, but cycle route planning needs consideration for height metres, unpaved/paved roads (Google StreetView etc used a lot to find a Sustrans route is actually unfit for road bikes) etc. So.. Importing a route planned elsewhere (gpx, kml or something) would be a real alternative, or a workaround. Asking the device to do its own planning from one point to another really isn't workable.
Please make the Nokia's USP an actual USP again?

Bookmark routes in iPhone Maps

Is there a way to bookmark a route in the maps application on the iPhone? I regularly use my phone to get a quick view of traffic conditions and routes, and although the recent tab does store some routes I would find it more convenient to just have my routes bookmarked. Has anyone had any success on this, if it is possible.

No, but I have most of the places I need to go bookmarked and thus can quickly enter them to get a route. Normally can enter start and end and get a route in under 10 seconds (along with clicking traffic icon to get traffic).
You can suggest it over at Google (since they made it and maintain it and provide updates to Apple for any future upgrades).

Router to Router Dialer VPN

one of my router is configured with site to site vpn, I want this router to establish a dialer vpn from a remote router,
Remote router will be configured as dialer vpn as there is no Live IP available in remote site, I dont want to configure it as Site to site vpn,
Please refer some docuement to achive this goal,

Hi Karsten -
I'm afraid I cannot use the EasyVPN feature at all.
The vendor informs me that there is another IPSec VPN tunnel which connects back to their office to provide other capabilities.
So I have to use L2L IPSec -- and do it with a dynamic IP from the router side, to a fixed IP on the ASA side.
Is it possible to build the tunnel-group on the ASA side so that it doesn't require a known IP for the remote side of the tunnel?
I'm using DefaultL2L tunnel group (on the ASA) at the moment to terminate the VPN when the router is using the satellite connection via FA90/1, with a fixed IP address.
But the DefaultL2L group doesn't have the IP of the router -- yet it works...
The same VPN config, used from the FA0/0 interface of the router with the same crypto map
just gives the traditional "No match, deleting SA" message..
I can see the router trying to establish the VPN, but it's just not able to negotiate, and the only reason I could think of was that the FA0/0 interface had a DHCP address instead of a static IP.
Strange that it works OK with the ASA's DefaultL2L tunnel group, with no mention of the router's FA0/1 static IP, yet the FA0/0 with a dynamic IP won't work.
We did just hook up the satellite and used FA0/1 to test it -- vpn came up instantly...

Routes and Routes Determination

Hello All,
I m basically a technical person and i m doing recording for routes and routes determination.
I am facing one problem.
while executing transaction 0vtc in one system , while saving data its asking for transport request.
and when i execute the same transaction in IDES system , and when i save data it does not ask for the transport request.
Is there any config for that?
Please help me out...its required asap..
thanks,
jigs
Helpful ans will be rewarded.

Hi
not sure if this would help. but going through some of the older posts here, here's something I gathered:-
++++++++++++++++++++++
It also depends on the client settings, which is done by the BASIS guys. If the client settings are done in such a way that system should not generate requests then it will not generate a request.
If the system is created as a Sandbox then also system will not ask for a request.
using the T codes SE01 where all the list can be viewed , then select the task or transport request click on the trucj button .
+++++++++++++++++++++
hope it's a start

Difference between Routing & Rate Routing

Hi All,
can anyone tell me difference between Routing & Rate Routing? can we use routing for REM? if no, then what will be the effect?
Thanks,
Rinky

Hi Rinky ,
Routing and rate routing are task list in broad manner .
standard task list: Describes the worksteps necessary to produce a material or perform an activity without reference to an order.( that means they are created without reference to order )
Essential objects of a task list are header, operations, material component allocations, production resources/tools and inspection characteristics.
Together with specific dates and quantities, task list data forms an important part of the order.
The following task list types exist in the R/3 System:
routing
reference operation set
rate routing
reference rate routing
inspection plan
maintenance task list
standard network
master recipe
Routing is created with ca01 and rate routing by ca21 .
Routing is used in discrete manufacuting and rate routing in repetitive .
Rate routing generally has only one operation and prod line instead of work centers and operations in routings .
Both routings can be used for scheduling , cosing and capacity planning .
Hope this was helpful answer !
Neal
Edited by: Neal Gibson on Jun 30, 2008 11:46 AM

Routing & rate routing

hello everyone,
myself rekha bamgude,i want to know difference between routing & rate routing?

Hi rekha to get a quick (or any) response, create your new discussion in a space related to your query. This way it will be visible to topic experts who will then see and reply to it.
Please move this thread to the relevant forum Enterprise Resource Planning (SAP ERP)
as you mention
i want to know difference between routing & rate routing?
Many times we told this word (Search before you post ).
please see this thread for more details.
Difference between routing and rate routing
poorna

Routes and route groups expanded

Is there any way to force the routes and route groups to show un-expanded when I click on the Routes/Groups tab in switch executive? I have many and it is difficult to navigate when they are all expanded.
kph

Hi kphite,
At this time, there is no method to force the collapse of the routes and route groups. However, thank you for this product suggestion. Just so you know, we have previously considered the implementation of such a feature and agree that this functionality would be beneficial. We do have it in our plans for future revisions of NI Switch Executive.
Thanks again!
Chad Erickson
Switch Product Support Engineer
NI - USA

Router to Router VPN with Overlapping internal networks

Hello Experts,
One quick question. How do I configure a Router to Router VPN with overlapping internal networks???
Both of my internal networks have ip address of 192.168.10.0 and 192.168.10.0
Any link or config will be appreciated. I've been looking but no luck.
Thanks,
Randall

Randall,
Please refer the below URL for configuration details:
Configuring an IPSec Tunnel Between Routers with Duplicate LAN Subnets
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00800b07ed.shtml
Let me know if it helps.
Regards,
Arul
** Please rate all helpful posts **

Router-to-Router VPN Security

Hi there,
Should we worry about the the security on router-to-router VPN over internet (IPSec) ?
We have two offices.
Office A has Cisco 2811 router (internal, private) and ASA 5510 firewall.
Office B has Cisco 2821 router (internal, private) and ASA 5505 firewall.
Office B has private subnets that extend to 7 hops away. (running RIP)
If we want to set up a site-to-stie VPN between these two offices, should we set it up on ASA's or routers?
If we set up VPN on routers, does that mean we need to connect one interface to the internet on each router and suffer from Internet attacks?
How do we defend our routers then?
Thanks in advance!
-Andrew

Hi,
when it comes to site to site vpn I usually prefer routers. Whith a little bit of tweaking NAT and routing you should be able to operate a public address on the routers even if they are behind the firewall.
The advantage of IOS based VPN is e.g. the possibility of routing protocols through the VPN tunnels which would give another level of resiliency. Configure tunnel interfaces on the routers with a tunnel mode IPsec and a tunnel protection profile. You can then run e.g. EIGRP to find a possible alternate path if one of the tunnels fails. Its much easier than anything I can think of on the ASA.
Rgds, MiKa

ISR router EIGRP Route Tag

Hi,
Wondering any one has successfully set route tag for EIGRP routes?
What I am trying to achieve here is to set route tag for the summary routes of the connected interfaces and subnets of some other connected interfaces.
Let's say an ISR router R1 with IOS 15.1(4)M3 has three interfaces running with EIGRP.
Interface Gi0/0
ip add 172.16.0.1/24
summary-add 172.16.0.0/16
Interface Gi0/1
ip add 172.16.1.1/24
summary-add 172.16.0.0/16
Interface Gi0/2
ip add 192.168.2.1/24
I am having difficulty to set route tag for summary add 172.16.0.0/16 and 192.168.2.0/24 before they get advertised to another router.
Any idea please?
Thanks
Cedar

Duplicate posts.
Go here: https://supportforums.cisco.com/discussion/12256521/isr-router-eigrp-route-tag

How to verify the routes from router when Polycom device Initiates traffic

Hi,
Could anyone please assist me in finding out the routes when Polycom device initiated traffic towards the BCS global.
1) polycom equipemnt is connected to the Internal Lan of the customer and its traversing through Router,
I checked though Ip accounting when the user initiates the traffic. (polycom device ip is x.x.x.10 and BCS global network is aa.aa.aa.0). When i checked IP accounting i found the destination ip is x.x.x.10 and source ip is aa.aa.aa.205 when user initiates traffic from Polycom device.
2) I also found the static route in router for BCS global network (aa.aa.aa.0) but when I tried to trace route to IP address (aa.aa.aa.205) the output shows:
1. * * *
2. * * *
10) * * *
Could anyone please assist me is there any other any other way to find out the routes.

Thanks, this did it for me. The verification from rommon was ok and I guess I can trust the rom even when not comparing the information with cisco webpage.

Want to change router name on map

Using Network Magic 5.5
When I bring up the map & click on the Router the MAC & IP info are correct..
However the manufacture; Name, Model, & connection Name are wrong.. In fact I hada wireless router I tried to use and never got to work so I took it out, now it's name & model # show up here, and the extra printer I can't get to work on here is now the connection name, Is there a way I can change this manually
1Snowbird

1snowbird wrote:
Using Network Magic 5.5
When I bring up the map & click on the Router the MAC & IP info are correct..
However the manufacture; Name, Model, & connection Name are wrong.. In fact I hada wireless router I tried to use and never got to work so I took it out, now it's name & model # show up here, and the extra printer I can't get to work on here is now the connection name, Is there a way I can change this manually
Hi 1Snowbird,
Do the following on each computer. Do not reinstall until Network Magic is removed from each computer, first. Installing Network Magic again on each computer, won't change a thing, if reinstalled right away.
Folder locations for Windows XP.
Uninstall Network Magic. Reboot.
Use Explore and remove the following folder and its sub-folders:
\Documents and Settings\All Users\Application Data\Pure Networks
\Program Files\Pure Networks
Still using Explore manually clean out your \Temp Folders. Run Disk Cleanup.
Reboot. Make sure that you are connected to the Router.
Reinstall Network Magic.
thecreator - Running Network Magic version -5.5..9195.0-Pure0 on Windows XP Home Edition SP 3
Running Network Magic version -5.5.9195.0-Pure0 on Wireless Computer with McAfee Personal Firewall Build 11.5.131 Wireless Computer has D-Link DWA-552 connecting to D-Link DIR-655 A3 Router.

How can I record a route on OVI Maps?

I have done this before so I know it can be done. I just forgot how I did it. So here's what I did, I started driving from my house and told ovi maps to calculate my route when I reached my destination I said stop navigation(or something on those lines) and it created my route exactly the way I drove. I forgot how I did this exactly so can anyone please help me out here? Thank you.

@DhruvSharma
Is this upon 5800XM using Ovi Maps v3.06 or have you changed device?
Happy to have helped forum with a Support Ratio = 42.5

Route shaping / Route Mapping

Similar Messages

Maybe you are looking for