RV082 drops WAN connection immediately after establishing it

I have my 2nd WAN connection on the RV082 setup to connect via static IP to a T1 connection. When I connect the cable, the log reports...
"WAN connection is up : 216.130.xxx.xxx..." and 3 sec's later reports "WAN connection is down".
I can connect a computer directly to that T1 with the same static IP settings and it connects without a problem.
I'm on the firmware version v4.0.2.08-tm.
Any thoughts?

I was using Smart Link Backup. Changing to Load Balanced brings the other WAN up. Is that normal behaviour? That if you're using the Smart Link Backup it shows the backup WAN interface as being down (in the logs) and no IP info (all 0.0.0.0) in the WAN status.
If the primary WAN goes down, will it then auto bring up the back WAN interface?
I'm on v4.0.2.08-tm firmware and i also changed the MTU to 1492.

Similar Messages

SA 540 drops wan connectivity after some time interval

hello guys,
I have problem. after a certain period of time (ranging from 2 minutes to several hours) the unit keeps dropping the WAN connection, making the unit unaccessible from the WAN side. The strange thing is, that when the connection is dropped, the unit is perfectly accessible from the LAN side, the WAN LED is still on, status info shows the WAN link up, and packet trace shows broadcasted traffic on the WAN interface, so only the directed communication to and from the ISPs gateway (configured to fix IP) seems to be blocked for some reason. When this happens, then plugging the WAN cable to the Optional WAN port enables traffic again, but it is also dropped after some time, and then only power cycling the unit restores WAN connectivity.
please suggest me as soon as possiblethat how to fix this problem?
Awaiting for valuable reply.....

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

WRT54GL frequently drops WAN connection

Hi,
I'm having a problem with my WRT54GL 1.1 router, namely it has a nasty habit of dropping WAN DSL connection. Firstly I attributed this to modem, but my ISP's tech support sent me a list of connection resets that are caused by the router not the modem. This happens about 20x a day, lasts for about 20 sec, then reconnect, works fine for a while and the whole cycle is repeated again. As you can imagine it is very frustrating.
I have the router upgraded to firmware rev. 4.30.11 and am using router's DHCP server.
Also: before you suggest it - I have connected my IskraTel Ganymede 822+ DSL modem directly to my PC and the connection is completely stable.
Any suggestion would be appreciated.
With kind regards,
Bostjan Ursic

It is difficult to be sure from the documentation, but it appears that your "DSL modem" is actually a "DSL modem router", and it uses the same 192.168.1.x subnet as the WRT54GL.
To fix your problem, you will need to make one or more changes. First, power down your entire network, then disconnect the WRT54GL from your modem. Then wire one computer to a LAN port on the WRT54GL, and login to the WRT54GL. Change the "Local IP address" to 192.168.2.1   Then click the "Save Settings" button and wait (3 to 60 seconds) for the screen to refresh. You will likely be disconnected from the WRT54GL. This is normal, so do not worry about that. Power down your entire network.
Next, using an ethernet cable, connect one of the LAN ports on the "modem" to the Internet port of the WRT54GL.   Boot up your system. Did this correct the problem?
If you still have problems, please post the following info:
1) What "Internet Connection Type" is the WRT54GL set to?
2) Is the DHCP server turned on in the 822+ modem?   (Note: I assume that the DHCP server is turned on in the WRT54GL.)
Message Edited by toomanydonuts on 08-25-2008 05:39 PM

Rv042 v4.1.1.01-sp drops wan connection

I recently implemented the rv042 as a replacement for a wrt54gs running DD-WRT. I upgraded to the latest release (v4.1.1.01sp) to solve 6to4 and SIP problems. These problems were indeed solved. However after some minutes the WAN1 connection gets somehow disconnected from the ADSL modem.
It does show the public ip address, but I cannot ping the ptp router anymore. I also cannot renew the lease. Rebooting the rv042 does not help. When rebooting the modem it briefly works again, but then loses the connection again and it never comes back.
Currently I returned to the old wrt54gs as a workaround. Because I am planning on an extra WAN connection (via cable), which is the main reason why I bought the rv042, I am eager to get this problem solved quickly. Since the ADSL modem is pretty old, I ordered a more current one that also supports IPv6, so I do not have to use a 6to4 tunnel. I will test again with this new modem, but I doubt that it will solve my problem since I do not have any problems with the old router.
Has anyone seen this type of problem, and can I do something in the configuration to solve this? Or is it just a bug?
Thx,
Hans Feringa
I replaced the ADSL modem. That fixed the problem.

I recently implemented the rv042 as a replacement for a wrt54gs running DD-WRT. I upgraded to the latest release (v4.1.1.01sp) to solve 6to4 and SIP problems. These problems were indeed solved. However after some minutes the WAN1 connection gets somehow disconnected from the ADSL modem.
It does show the public ip address, but I cannot ping the ptp router anymore. I also cannot renew the lease. Rebooting the rv042 does not help. When rebooting the modem it briefly works again, but then loses the connection again and it never comes back.
Currently I returned to the old wrt54gs as a workaround. Because I am planning on an extra WAN connection (via cable), which is the main reason why I bought the rv042, I am eager to get this problem solved quickly. Since the ADSL modem is pretty old, I ordered a more current one that also supports IPv6, so I do not have to use a 6to4 tunnel. I will test again with this new modem, but I doubt that it will solve my problem since I do not have any problems with the old router.
Has anyone seen this type of problem, and can I do something in the configuration to solve this? Or is it just a bug?
Thx,
Hans Feringa
I replaced the ADSL modem. That fixed the problem.

SA540 - Continuously drops wan connection

It's been nothing but a nightmare since i've gotten the 540. My firmware is 1.1.42 and I have a very basic setup with only a couple of standard firewall rules. The 540 keeps dropping the wan connection. Everything is static on the LAN side and DHCP is turned off on the 540 with Static IP for the WAN. I've factory reset twice and reconfiged everything exactly the same with of course the same results...help!!!
Thanks
James

This is probably worthy of a case with high priority at the SBSC (small business support center - aka TAC).
That is the new FW and you have factory reset so sounds like you have dont everything they way you should have.
There are a few things to try...
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Firewall -> Attacks
Under ICSA settings, uncheck the box for block fragmented packets.
Also, lower the MTU size and see if that helps (usually do this for DSL).
Also, see if you can collect a WAN trace (easy on this appliance) using Administration: Diagnostics: Packet Trace (turn it on, catch the anomaly, then turn it off). This will open into Wireshark (formerly Ethereal) right on your PC.
Steve

LRT224 hickups: dropping WAN connection??

Hi,
my new LRT224 shows hickups in my connection.
It is hooked up to a 100Mbit fiber connection from my isp.
If I try to stream video, it creates every minute or so a second or two pause in the transmission.
Clearly, this breaks my continuous video stream.
The device log (shown below) does report 'WAN connection is down', which seems rather strange and unexpected to me.
If I don't stream video, and the data link is nearly idle, these intermittent 'WAN is down' messages do continue.
If I take the LRT out, and connect my PC directly to the isp line (yes, bad practice) I don't have such hickups, and the video streams fine (at a few mbit/sec).
I updated the firmware to v1.0.1.01 but that didn't make a difference.
I actually disabled the 2nd WAN port.
In the 'dual WAN' config, the 'Enable network Service Detection' is not marked. Selecting 'Link failover' or 'Load balance' does not show any difference (no improvement).
Any clue why the LRT would report 'WAN connection is down'???
I urgently need some solution, but the issue seems beyond my skills...
(In the log I also see 'policy violation's. I have no idea why these occur: I have no firewall rules on those LAN or WAN IP addresses...)
Thanks for any insight!
Jos
This is a caption of the device log:
Feb 26 18:28:37 2014 System Log WAN connection is down
Feb 26 18:28:38 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Feb 26 18:30:51 2014 Connection Refused - Policy violation TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
Feb 26 18:30:58 2014 Connection Refused - Policy violation TCP 192.168.1.108:65516->89.248.168.42:3129 on eth1
Feb 26 18:31:33 2014 System Log WAN connection is down
Feb 26 18:31:34 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Feb 26 18:31:36 2014 ACCESS_RULE TCP 192.168.1.107:65516->157.55.56.153:3129 on eth0
Feb 26 18:31:37 2014 Connection Refused - Policy violation TCP 192.168.1.106:55159->199.9.249.46:1935 on eth1
Feb 26 18:31:37 2014 Connection Refused - Policy violation TCP 192.168.1.106:55158->199.9.249.46:1935 on eth1
Feb 26 18:31:37 2014 ACCESS_RULE TCP 192.168.1.107:55158->157.55.56.153:1935 on eth0
Feb 26 18:31:51 2014 Connection Refused - Policy violation TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
Feb 26 18:32:50 2014 System Log WAN connection is down
Feb 26 18:32:51 2014 Connection Refused - Policy violation TCP 192.168.1.108:49527->78.235.240.121:57236 on eth1
Feb 26 18:32:51 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Feb 26 18:33:51 2014 Connection Refused - Policy violation TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
Feb 26 18:33:58 2014 Connection Refused - Policy violation TCP 192.168.1.108:49374->89.248.168.42:3129 on eth1
Feb 26 18:34:51 2014 Connection Refused - Policy violation TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
Feb 26 18:34:59 2014 Connection Refused - Policy violation TCP 192.168.1.108:49499->90.24.175.227:57402 on eth1
Feb 26 18:39:06 2014 ACCESS_RULE TCP 192.168.1.107:49499->111.221.74.31:57402 on eth0
Feb 26 18:39:13 2014 Connection Refused - Policy violation TCP 192.168.1.108:49837->89.248.168.42:3129 on eth1
Feb 26 18:39:13 2014 ACCESS_RULE TCP 192.168.1.107:49837->65.55.223.46:3129 on eth0
Feb 26 18:39:57 2014 Connection Refused - Policy violation TCP 192.168.1.108:49584->92.142.109.203:57209 on eth1
Feb 26 18:42:32 2014 System Log WAN connection is down
Feb 26 18:42:33 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Feb 26 18:43:16 2014 System Log WAN connection is down
Feb 26 18:43:18 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Feb 26 18:49:53 2014 System Log WAN connection is down
Feb 26 18:49:54 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Feb 26 18:50:42 2014 System Log WAN connection is down
Feb 26 18:50:44 2014 System Log WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
Solved!
Go to Solution.

There is a new update firmware for LRT224.

Dropping WAN connection

We have installed a new Time Capsule running Version 7.5.1... Running both Ethernet and Wireless connections from a DSL modem for WAN connectivity... We are getting continuous (2 to 3 times per day) WAN disconnects... the router works fine just that we all lose our internet access...
We have several ports open for external access to various accounting package and operational databases...
Thinking it was the phone company we had them replace the DSL modem with their most current version and still have problems....

I had a replacement TC sent - it was worse - returned it.
I placed it behind my LinkSys router - still dying.
I spoke to support again - that had one "expert" calling me - what an arrogant SOAG, at some point he said - "end of conversation" and slammed the phone.
He had never heard of the problem - "most be the ISP's equipment or my LinkSys".
Tried to explain him that i'm not the only one - just check apple forums - that the TC has problems with my Siemens fiber modem (LinkSys doesn't), and even placing my Linksys router between doesn't help.
For me this all indicates that the firmware on the TC is not stable - he argued that this is not the case, this is a compatibility issue. I agree that it might be a compatibility issue - but the root cause is still the firmware of the TC.
He wanted to have me to try the TC at a different location with different ISP - but for me that would just show that the TC works in some setups - but for him that would 100% clear the TC of any blame - that makes no sense.
Am I wrong - or is the "expert" wrong - give me your opinion, thanks.

Kludgy fix for T520 frequently dropping WAN connection

There's no obvious way to lodge a bug with Lenovo. Hopefully someone from the tech dept looks in here from time to time.
The problem:
T520 (4242CTO) running Win7x64. Accessing WAN (Telstra NextG 850Mhz HSPA) via F5521gw. Connects initially without issue. Then drops connection after random time interval. Doesn't matter whether connection active or idle. Persistently fails on any/all reconnection attempts.
The fix:
In Control Panel/Device Manager, disable "Network adaptors/F5521gw Mobile Broadband Driver" and "Ports (COM & LPT)/F5521gw .... (COM4)". Then reenable same. Reconnects on next attempt every time.
Presumably there's some issue with releasing/renewing authentication/IP etc. Perhaps something to the effect of resetting the adaptor could be trialled for inclusion in future releases of Access Connections?

There's no obvious way to lodge a bug with Lenovo. Hopefully someone from the tech dept looks in here from time to time.
The problem:
T520 (4242CTO) running Win7x64. Accessing WAN (Telstra NextG 850Mhz HSPA) via F5521gw. Connects initially without issue. Then drops connection after random time interval. Doesn't matter whether connection active or idle. Persistently fails on any/all reconnection attempts.
The fix:
In Control Panel/Device Manager, disable "Network adaptors/F5521gw Mobile Broadband Driver" and "Ports (COM & LPT)/F5521gw .... (COM4)". Then reenable same. Reconnects on next attempt every time.
Presumably there's some issue with releasing/renewing authentication/IP etc. Perhaps something to the effect of resetting the adaptor could be trialled for inclusion in future releases of Access Connections?

I have just purchased an ipad 2 (already have an inpad1) and after syncing through itunes it will not conncect to my home wifi connection. The first ipad connected immediately when bought. this one indicates my wifi address but states not connected.

I have just purchased an ipad 2 (already have an ipad1) and after syncing through itunes it will not connect to my home wifi. The first one connected immediately after setup. This one indicates my wifi accpimt bit states not connected. Help!

What make, model and version router do you have?
Is MAC address filtering turned ON in your router?
Do you have a limit on the number of connections set in your router?
What type of security are you using, i,e, WEP, WPA, WPA2?
Have you tried restarting your router? (remove power for 30 seconds and restart)
Does your iPad 2 work on any other networks? Starbucks, Borders, etc

Lost WAN Connection Three Times in Past Two Weeks

For the third time in the past two weeks, I had to call the support line and walk through the process of having my WAN connection reset after losing my connection to the Internet. Restarting the router after waiting a minute does not resolve the issue. I have to call and work with the automated system to have the loss of connection verified and then it is reset on Verizon's end. This problem did not start until my speed match started. There were two weeks between the first reset, but there have only been two days since the last reset. Has anyone else experienced this issue? Thanks in advance.

In general when you lose connection try to look at the link lights on the router and see if your losing the wan coax light. If you do then your losing coax physical connectivity.
If you have access to the main ont then instead of calling in you can reset it yourself. Some of them are easier to reset than others. Find the alarm silence reset and hold it down for fifteen seconds and make sure the lights drop

Airport Extreme(SW) keeps dropping the WAN connection under "heavy" load

Hey,
Have had this problem ever since I got the Airport Extreme when it first came out and I got it.
The problem is this : The connection will work just fine for ages, but if I end up downloading something using (primarily this is the problem) torrents and I end up getting a rather good speed on it the airport will all of the sudden stop getting data from the WAN(ADSL modem connected to it through the WAN connection) and the Airport will have to be restarted. Some days it will have to be restarted up towards 15 times a day.
The Airport remains accessible through the LAN connection, as well as through the WiFi when it has failed like this so I can go in through the Airport Admin Utility and restart the unit without any problems whatsoever. The modem does not need restart or reiniting either.
The problem occurs no matter of if I am on the hard wired (LAN) connection or the WiFi connection. If I download something using a torrent that is high speed, especially if its more then one torrent at the same time (say 4 torrents each running at 200-300kbps therefor peaking at the roof of what my DSL connection can handle) then it will absolutely lock up after a minute or so. If I only do surfing or 'ordinary' work then there is no problem.
The problem is easily repeated.
* If I connect my laptop by wire to the modem directly without the airport in between there will be no problem.
* I have software reseted the Airport many times to attempt to fix the problem when it has gotten on my nerves with no positive or changing result.
* I have the latest available from Apple firmware(5.6) installed on the Airport.
* I have no 'weird' or abnormal settings set on the Airport, and no neighbors playing tricks on me - This problem was with me when I used the airport fully locked down in a office environment and then went with it when I moved my airport unit out of my office in to my home.
* I have no other wifi units in the house that may cause problems, no bluetooth phones running amok.
Airport details:
Apple Airport Extreme Base Station
Firmware Version: 5.6
Wireless Security : Not currently enabled
Wireless Channel : 1 (automatic)
Built in modem : No
Prod # : M8930LL/A (A-1034)

Hi guys,
Recently I bought AirPort Extreme 802.11n Base Station (Gigabit, MB053LL/A), and
seems, I have very similar problem with yours. Internet connection from my ISP over WAN is dropped after few hours of being idle. The router successfully receives its IP settings from provider's DHCP, eveyithing is working fine at first and as long as I have some inet activity. Then I disconnect, or sleep my laptops, and when I'm back - WAN provides no Internet traffic at all It looks like WAN is not functioning or blocked in someway. AirPort Utility and logs show no problems, all statuses are good, correct WAN IP settings are shown in the utility.
Sometimes it helps to plug-out/in Ethernet cable to WAN port, but more often only full router restart helps (with around 10-20 secs of outage). BTW, WiFi connection between the router and laptops is pretty stable and causes absolutely no probs. HDD connected to the router works good also.
My firmware is 7.2.1 (gigabit), and reading above posts I tried to downgrade to 7.2. It didn't fix the problem So well there are no earlier firmware versions for this AEBS model to try.
Does anybody have ideas about it?
(I understand you guys mostly wrote about 100Mbit version of AEBS)
Thanks you,
Strim

Stable 10.3mb connection dropped to 0.3mb after HH...

After 2 months with a stable 10.3MB downstream connection, my homehub3 now connects @ 280Kbps
latest stats from HH3
ADSL Line Status
Connection Information
Line state:   Connected
Connection time:   0 days, 10:43:50
Downstream:   280.6 Kbps
Upstream:   443.9 Kbps
ADSL Settings
VPI/VCI:   0/38
Type:   PPPoA
Modulation:   G.992.5 Annex A
Latency type:   Interleaved
Noise margin (Down/Up):   31.4 dB / 25.2 dB
Line attenuation (Down/Up):   35.1 dB / 21.3 dB
Output power (Down/Up):   7.1 dBm / 12.8 dBm
FEC Events (Down/Up):   0 / 0
CRC Events (Down/Up):   0 / 3
Loss of Framing (Local/Remote):   0 / 0
Loss of Signal (Local/Remote):   0 / 0
Loss of Power (Local/Remote):   0 / 0
HEC Events (Down/Up):   0 / 2
Error Seconds (Local/Remote):   41 / 20
The connection has dropped a few times in the last week but indicates a good? noise margin each time
    Line 65: 09:34:52, 12 Jul.   (452895.510000) WAN operating mode is DSL
   Line 66: 09:34:52, 12 Jul.   (452895.510000) Last WAN operating mode was DSL
   Line 70: 09:34:47, 12 Jul.   (452891.070000) DSL is up
   Line 71: 09:34:45, 12 Jul.   (452889.000000) DSL noise margin: 24.40 dB upstream, 31.40 dB downstream
   Line 72: 09:34:44, 12 Jul.   (452887.890000) DSL line rate: 443 Kbps upstream, 280 Kbps downstream
   Line 75: 09:33:53, 12 Jul.   (452836.180000) DSL is down after 1048 minutes uptime
   Line 151: 16:05:15, 11 Jul.   (389912.320000) WAN operating mode is DSL
   Line 152: 16:05:15, 11 Jul.   (389912.320000) Last WAN operating mode was DSL
   Line 156: 16:05:10, 11 Jul.   (389907.980000) DSL is up
   Line 157: 16:05:08, 11 Jul.   (389905.830000) DSL noise margin: 24.80 dB upstream, 17.40 dB downstream
   Line 158: 16:05:07, 11 Jul.   (389904.740000) DSL line rate: 444 Kbps upstream, 287 Kbps downstream
   Line 161: 16:04:16, 11 Jul.   (389853.310000) DSL is down after 4847 minutes uptime
   Line 235: 01:58:32, 10 Jul.   (252700.130000) WAN operating mode is DSL
   Line 236: 01:58:32, 10 Jul.   (252700.130000) Last WAN operating mode was DSL
   Line 343: 07:17:13, 08 Jul.   (99016.430000) WAN operating mode is DSL
   Line 344: 07:17:13, 08 Jul.   (99016.430000) Last WAN operating mode was DSL
   Line 348: 07:17:09, 08 Jul.   (99012.980000) DSL is up
   Line 349: 07:17:07, 08 Jul.   (99010.910000) DSL noise margin: 25.40 dB upstream, 17.30 dB downstream
   Line 350: 07:17:05, 08 Jul.   (99009.410000) DSL line rate: 444 Kbps upstream, 287 Kbps downstream
   Line 353: 07:16:14, 08 Jul.   (98957.690000) DSL is down after 1045 minutes uptime
   Line 422: 13:50:39, 07 Jul.   (36217.010000) WAN operating mode is DSL
   Line 423: 13:50:39, 07 Jul.   (36217.010000) Last WAN operating mode was DSL
   Line 427: 13:50:34, 07 Jul.   (36212.830000) DSL is up
   Line 428: 13:50:32, 07 Jul.   (36210.700000) DSL noise margin: 25.60 dB upstream, 17.30 dB downstream
   Line 429: 13:50:31, 07 Jul.   (36209.220000) DSL line rate: 440 Kbps upstream, 287 Kbps downstream
   Line 437: 13:29:19, 07 Jul.   (34937.610000) DSL is down after 580 minutes uptime
   Line 485: 03:48:27, 07 Jul.   ( 84.240000) WAN operating mode is DSL
   Line 486: 03:48:27, 07 Jul.   ( 84.240000) Last WAN operating mode was DSL
   Line 490: 03:48:24, 07 Jul.   ( 81.570000) DSL is up
   Line 491: 03:48:22, 07 Jul.   ( 79.510000) DSL noise margin: 24.40 dB upstream, 17.00 dB downstream
   Line 492: 03:48:21, 07 Jul.   ( 78.400000) DSL line rate: 440 Kbps upstream, 287 Kbps downstream
I've tested the Home hub & an older Linksys WAG354G (which has been reliably connecting @ 8Mbs for the last few years on this line), at the master socket (with all other extensions disconnected) and the connection (sync) speed on both devices is approx 287Kbps.
I've also run the quiet line test a few times and hear no noise at all.
Will the connection automatically re-adjust back to a faster connection or do I need to request help?

frfom what you have posted it looks like all the drops in connection and manual resets have resulted in your connection being put in banded profile until the exchange see your conenction as stable. you need to stay connected 24/7 for 3+ days with no resets and the banding should release automatically. if still connecting at about 288kb and have 3+ days conencted then repost your stats as you will need mod assistance
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

E3000RM - WAN connection dropped

Pros: Good Price. Worked very well when it did operate.
Cons: I purchased this approximately 5 weeks before I got around to using it. After installation, it worked for two days and failed. The WAN connection dropped, and numerous attemps to reconnect failed. Since I was approximately one week past the expiry date of the warrenty I guess I am out of luck and learned a lesson to test upon receipt.

In this case you can reset the router and try to run the cisco connect software that came along with the router to reconfigure it (Note: If you already have cisco connect on your computer then uninstall it first before reinstalling it.). After that you can get into the advance settings of the router through cisco connect and try to reduce the MTU size to 1400.
Click on the following link that shows how to reduce the MTU size http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=66270e5d0d4347d087102f2bfef7116d_3742.xml&pid=80&r...

GX520 hangs after establishing server connection

We are running ZFD 6.5 sp2 and trying to image new GX520's
There are 21 machines all exactley the same down to every last BIOS line,
DELL GX520.
I used the bootcd.iso from SP2
Set up a policy to install an image to any PC booting within a given IP
range.
Here is the issue:
I installed the boot loader on all twenty PC's
7 PC's took the image just fine
14 hung with no error after establishing server connection and the path
to the image.
Zimglog.xlm shows
- <WS DN="R3NWTS01.R3.usnrc">
<Tree>NRC_TREE</Tree>
<Status>Failure</Status>
<ErrorMessage>Workstation failed to restore image as the base image
already exists.</ErrorMessage>
<Operation>Download</Operation>
<ImageType>Base Image</ImageType>
<ImagePath>\\R3NWTS01\NRC\zen-img\train2.zmg</ImagePath>
<Timestamp>Tue Apr 11 12:13:08 2006</Timestamp>
When I try a manual download I get "no eligible partitions to recieve
Image"
Any thoughts?
Thanks
Thomas Magee
US NRC
Network Manager
[email protected]

Tmm3,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

My i Phone drops WiFi connection after just a few minutes and wont reconnect unless I reset the network settings and reboot the phone?

My i Phone 4s has suddenly started to drop wifi connection after nealy months of near perfect connections?
To restore a wifi connection I have to reset the network settings and restart the phone, this only fixes the issues for around 2-3 mins?
Other quick fixes like switching wifi on and off/ switching to airoplane mode for a few secconds have no impact.
This is really annoying as I am using my data allowence very quickly, and as the phone is continually searching for a wifi connection the battery time has reduced dramatically.
I just wondered if any one else has the same issue, and any suggestions as to how I can fix this.
Thanks in Advance

Reboot.
Restore (from backup)
Restore (as new)
Test after each step. If one of them doesn't fix the problem, make an appointment at the genius bar.

RV082 drops WAN connection immediately after establishing it

Similar Messages

Maybe you are looking for