RV220W - VPN PPP & RDP problem

Hello!
This is my first post here, so welcome!
I have purchased RV220W router and implemented into the existing netowork. Everything seems to work fine except logging into rdp desktops of wxp's on the local network in the office.
I'm not using router's VPN capabilities. I have made a connection through one of the WXP's VPN locally in the office. I login with password as PPP connection. Everything works fine, but I can only connect through RDP to the machine that is making the connection by "VPN IP". I cannot login to any IP that is local in the office. I can not ping either.
We are using also Macs and the same problem is when connecting with ScreenSharing and pinging.
It is definitely something to be set on the router.
If you have any idea, I would apprecite your help!

Hi again!
After reading similar post I found a "solution".
I have manually put actual RV220W IP as router ip (except of the ip of the XP that is making the vpn connection) on the computer I'm connected to VPN and now it's working fine.
Anyway, thanks for approving this thread.
Cheers,
Adam

Similar Messages

Starting AnyConnect VPN through RDP Session

Hi,
We have AnyConnect (ver 3.1.01065) configured on our ASA5520 boxes. VPN is working fine from the desktop, but I also need the ability to establish a VPN connection through a RDP connection (i.e. I'm using RDP to connect to a PC which has AnyConnect installed on, then trying to establish a VPN connection).
I've downloaded the Cisco VPN Profile Editor, chaned the <WindowsVPNEstablishment> option to "AllowRemoteUsers". Then applied the profile to the relevant Group Policy. Connected VPN from the PC (not through RDP), so that it downloads the new profile, and then disconnected again.
However, I still can't start VPN through an RDP connection. (Error is "VPN establishment capability from a remote desktop is disabled. A VPN connection will not be established".)
I've checked the XML file on the local PC to confirm the profile has been downloaded (and is has, and I can see the AllowRemoteUsers option.
This also happened with the previous version of AnyConnect (3.0.xxxx).
The PC's local routing tables look fine, and I can't see any conflicts that would cause the RDP session to drop.
Also - If I connect VPN, then RDP onto the PC, both the VPN and RDP sessions work fine.
Any ideas would be appreciated!
Thanks
Tony

Hi Portu,
Thanks for your reply, and thanks for confirming that it works with AC 3.1 and ASA 8.4 (I'm using the same ASA version).
It looks like the issue was that I created the profile with the standalone Cisco VPN Profile Editor, saved it, uploaded it to the ASA, I then added a new profile on the ASA (in the Cisco AnyConnect Profiles section), and specified the file... however, it appears that I over wrote the uploaded profile, as the WindowsVPNEstablishment was set to LocalUsers. Once I changed it to AllowRemoteUsers and applied the config, then deleted the profiles from the client, it worked!
Simple mistake - but easily done!!
Thanks again
Tony

SSH client/server? VPN? RDP?

Does the N900 have an SSH-client? Or can it run as SSH server?
Support for VPN?
RDP client?
Greetings,
Evert
Regards,
Evert

OpenSSH client:
http://maemo.org/downloads/product/raw/Maemo5/openssh-client?get_installfile
OpenSSH server:
http://maemo.org/downloads/product/raw/Maemo5/openssh-server?get_installfile
VNC Viewer:
http://maemo.org/downloads/product/raw/Maemo5/vncviewer?get_installfile
For the LOVE of GOD, please don't download and install build-essentials via apt... the N900 has a very small / partition.. All additional software should be installed into /opt (which is a much larger partition, actually symlinked to /home/opt)
If you install build-essentials you will possibly fill your root partition and effectively hose your device..
If you want to compile packages yourself, you'll need to use the Maemot5 SDK on a desktop.. either to produce the package you want OR to product a copy of gcc etc that installs in /opt..
OR, consult downloads.maemo.org where the package you want may already be listed

ASA 5505 + ASA 5540 static VPN, ssh and rdp problems

Greetings!
I've recentely set up a VPN between Cisco ASA 5540(8.4) ana 5505(8.3).
Everything works fine, but there is a small problem that is really annoying me.
From the inside network behind ASA 5505 I connect via rdp or ssh to a host inside ASA 5540.
Then I minimize ssh and rdp windows and don't use it for ten minutes. But I still use VPN for downloading some files.
Then I open ssh window - the session is inactive, open rdp window - I see a black screen (for 10-15 seconds, and then it shows RDP)
There are no timeouts on ssh or rdp hosts configured, via GRE tunnel it works perfectly without any hangs.
What can I do to get rid of this problem?
Thanks in advance.

Dear Fedor,
You could try adding the following commands to your configuration (on both ASAs) in order to increase the timeout values of the specific TCP sessions:
access-l rdp_ssh permit tcp 1.1.1.0 255.255.255.0 2.2.2.0 255.255.255.0 eq 22
access-l rdp_ssh permit tcp 1.1.1.0 255.255.255.0 2.2.2.0 255.255.255.0 eq 3389
class-map TCP_TIMEOUT
      match access-list rdp_ssh
policy-map global_policy
     class TCP_TIMEOUT
          set connection timeout idle 0:30:00
          set connection timeout half 0:30:00
* Please make sure you define the specific RDP and SSH ports in the ACL and avoid the use of "permit ip any any".
Let me know.
Portu.
Please rate any post you find useful.

ASA 5505 AnyConnect VPN Can RDP to clients but can't ping/icmp

Hello all,
I've been searching all day for a solution to this problem. I setup and SSL anyconnect VPN on my Cisco ASA 5505. It works well and connects with out a problem. However, I can't ping any internal clients, but I can RDP to them. It may be something simple and I would appreciate any help. Most of the time people end up posting their config so I will as well.
MafSecASA# show run
: Saved
ASA Version 8.2(1)
hostname MafSecASA
domain-name mafsec.com
names
interface Vlan1
nameif inside
security-level 100
ip address 10.4.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 7.3.3.2 255.255.255.248
interface Vlan3
no forward interface Vlan1
nameif dmz
security-level 50
ip address 172.20.1.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
domain-name mafsec.com
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
protocol-object udp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object udp
protocol-object tcp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_4
protocol-object ip
protocol-object icmp
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_4 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_3 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list outside_access_in extended permit icmp any any
access-list inside_split_tunnel standard permit 10.4.0.0 255.255.255.0
access-list inside_split_tunnel standard permit 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool SSLVPNPool2 10.5.0.1-10.5.0.254 mask 255.255.255.0
ip verify reverse-path interface outside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 7.3.3.6 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 10.4.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.4.0.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd option 6 ip 8.8.8.8 8.8.4.4
dhcpd address 10.4.0.15-10.4.0.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd lease 86400 interface inside
dhcpd option 3 ip 10.4.0.1 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.3055-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.3055-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSLVPN internal
group-policy SSLVPN attributes
dns-server value 8.8.8.8 8.8.4.4
vpn-tunnel-protocol svc
group-lock none
split-tunnel-policy tunnelspecified
split-tunnel-network-list value inside_split_tunnel
vlan none
address-pools value SSLVPNPool2
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username user1 password
username user1 attributes
service-type remote-access
username user2 password
tunnel-group SSLVPNGROUP type remote-access
tunnel-group SSLVPNGROUP general-attributes
address-pool SSLVPNPool2
default-group-policy SSLVPN
tunnel-group SSLVPNGROUP webvpn-attributes
group-alias SSLVPN enable
prompt hostname context
Cryptochecksum:3b16cbc9bbdfa20e6987857c1916a396
: end
Thank in advance for any help!

Your config actually looks good (you have the ACL that would allow the echo-reply back since you don't have inspection turned on) - are you sure this isn't a windows firewall issue on the PCs? I'd try pinging a router or switch just to make sure.
--Jason

Work VPN for RDP

Hello,
I have a ASA 5510. I am tring to configure a vpn connection for multiple users. I would like them to be able to RDP into their work stations after establishing a VPN session then use the windows RDP (mstsc) to connect to their work station. I have created users in the (ADSM) AAA\Local Users - Local User section to be able to establish the connection. But I am getting SA proposal problems and Error processing payload 1 errors. I am by far not a wiz at this and we have purchased 20 of these units for remote sites. Is this possible without using software (Anyconnect etc.)? Is there an ADSM guide for this?
Any help would be appreciated.
Regards

There is an Anyconnect wizard in ASDM
Also here is the config guide-
http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect23/administration/23admin2.html

RV220W, VPN client, and Full Tunnel vs Split Tunnel capabilities

For an RV220W, which VPN client mode (of the three possibilities) supports which Tunnel mode?
This is mostly a question, and partly "in use" observations.
Background: I have been able to get all three different VPN clients to work with an RV220W, but only one of the three works in "Full Tunnel" mode (SSL VPN). And since I know one of the three -- the Cisco QuickVPN client -- will never with in that mode, do we know if an RV220W will with an IPSec client in Full Tunnel Mode?
If anyone answers yes, the next question will be vpn client and how did you configure it, client and RV220W, to make full tunnel work.
Summary of VPN modes I've gotten to work with an RV220W:
Client
Split Tunnel Works?
Full Tunnel Works?
OS?
Notes
SSL VPN
Yes
Yes
Win7/64
IE10 or IE11
QuickVPN
Yes
No
Win7/64
IPSec VPN
Yes
No
Win7/64
Shrew Soft VPN Client

I have to mark this as not a correct answer.
Reason: 0.0.0.0 will not go into either of the fields listed above, message is "Invalid IP address Please enter a value between 1 - 223 at xxx.0.0.0.".
To Michal Bruncko who posted this:
1.) 0.0.0.0 will not work in my router nor in the RV220W online emulator here, (general emulator page here), am I missing something obvious?
2.) Have you used these actual settings on your router, or did you answer in a theoretical, "this should work" way?

Cisco ASA 5520 Site-to-site VPN TUNNELS disconnection problem

Hi,
i recently purchased a Cisco ASA 5520 and running firmware v. 8.4(2) and ASDM v. 6.4(5)106.
I have installed 50 Site-to-Site VPN tunnels, and they work fine.
but randomly the VPN Tunnels keep disconnecting and few seconds after it connects it self automaticly....
it happens when there is no TRAFIC on, i suspect.
in ASDM in Group Policies under DfltGrpPolicy (system default) i have "idle timeout" to "UNLMITED" but still they keep disconnecting and connecting again... i have also verified that all VPN TUNNELS are using this Group Policie. and all VPN tunnels have "Idle Timeout: 0"
this is very annoying as in my case i have customers having a RDP (remote dekstop client) open 24/7 and suddenly it gets disconnected due to no traffic ?
in ASDM under Monitoring -> VPN .. i can see all VPN tunnels recently disconnected in "Login Time Duration"... some 30minutes, 52minutes, 40minutes and some 12 minutes ago.. and so on... they dont DISCONNECT at SAME time.. all randomly..
i dont WANT the VPN TUNNELS to disconnect, i want them to RUN until we manually disconnect them.
Any idea?
Thanks,
Daniel

What is the lifetime value configured for in your crypto policies?
For example:
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400

Cisco ASA 5505 VPN Remote Acces Problem

Hello Guys .. i have cisco 5505 Asa security Adaptive , and i have two local networks 192.168.1.0 /24 and 192.168.2.0/24 , and i have my ISP public connection,,,,,what i want to do is i want to connect Remote VPN connection and access my Private Network of 192. my public ip is like 155.155.155.0 /24 ...
i put my ISP connection in the EO/0 and my private networks into E0/1 and E0/2.
so i created a remote vpn connection ,, and then i connected to the VPN ..
My problem i can't reach and access my private networks .. this probem frustrated me a lot .. so cisco guys please help me
and iam using ASDM cisco graphic interface

Hi Timothy,
Could you please try disabling UAC in Win 7. Also try to connect from a machine where you have admin privileges (in case you are trying connection from a restricted machine.
Also, add the site under trusted sites in IE. i.e if you are connecting to https://1.1.1.1 or https://vpn.abc.com then please add it under the trusted sites:
Let me know if this helps.
Thanks,
Vishnu Sharma

PPP Mulilink problem

Need Help!
Got problem with ppp multilink. Set up it, but the interface show down, like that in both side:
Serial4:0 unassigned YES manual down down
Serial5:0 unassigned YES manual down down
check lthe phisical line, phisical line is ok.
here are configs of both sides
R1:
controller E1 0/0/0
framing NO-CRC4
clock source internal
channel-group 0 timeslots 1-31
controller E1 0/0/1
framing NO-CRC4
clock source internal
channel-group 0 timeslots 1-31
interface Multilink3
ip address 192.10.10.1 255.255.255.252
ppp multilink
ppp multilink interleave
ppp multilink group 3
interface Serial0/0/0:0
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 3
interface Serial0/0/1:0
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 3
R2:
controller E1 4
framing NO-CRC4
clock source line secondary 4
channel-group 0 timeslots 1-31
controller E1 5
framing NO-CRC4
clock source line secondary 5
channel-group 0 timeslots 1-31
interface Multilink3
ip address 172.28.235.37 255.255.255.252
shutdown
ppp multilink
ppp multilink interleave
ppp multilink group 3
interface Serial4:0
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 3
interface Serial5:0
no ip address
encapsulation ppp
ppp multilink
ppp multilink group 3
What to do?

I would assume the multilink interface on R2 been shut down is the issue
interface Multilink3
ip address 172.28.235.37 255.255.255.252
shutdown <------------------- do a no shut on this interface
ppp multilink
ppp multilink interleave
ppp multilink group 3

Ppp multilink problem

Hi
I am having a problem configuring ip rtp with interleaving on two 1721's prioritizing voice traffic between two ip voice devices over a 128k point to point link. This is my config...
interface Multilink1
ip address 192.168.24.2 255.255.255.0
no cdp enable
ppp multilink
ppp multilink fragment delay 20
ppp multilink interleave
ppp multilink group 1
ip rtp header-compression iphc-format
ip tcp header-compression iphc-format
ip rtp priority 8100 100 40
interface Serial0
bandwidth 128
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
ppp multilink
no cdp enable
Everytime I add the 'ppp multilink' to the serial, I get the virtual-access interface bouncing up and down with no traffic flowing.
any ideas?

Cannnnnnnnt see much wrong, try adding "ppp multilink group 1" to int S0 config.

RV220w VPN firmware 1.0.6.6

have an ip address than end in zero from isp the VPN set up menu will not allow you to put a zero in the last octet.
2015-03-05 07:14:32: [rv220w][IKE] ERROR: Could not find configuration for 71.3.174.0[500]

2015-03-09 08:32:00: [rv220w][IKE] INFO: Responding to new phase 2 negotiation: 192.168.250.148[0]<=>71.3.174.0[0]
2015-03-09 08:32:00: [rv220w][IKE] INFO: Using IPsec SA configuration: 10.10.100.0/24<->10.10.20.0/24
2015-03-09 08:32:00: [rv220w][IKE] ERROR: Not supported nested SA. Peer IP 184.106.55.77[0] does not match SA End Point
2015-03-09 08:32:00: [rv220w][IKE] ERROR: failed to create saprop.
2015-03-09 08:32:00: [rv220w][IKE] ERROR: Failed to get proposal for responder.
the 10.10.20.0/24 is from the ip 71.3.174.0 and the configure page will not let you put in that address:

HP T410 All-In-One (H2W21AA) serious RDP problem with terminal server

Hi there! The scheme is this:
HP T410 All-In-One (H2W21AA)
firmware that was out-of-the-box got some graphical problems with RDP, so i updated the Smart Zero Core Image to the latest Z6A44019 Rev. 1 (11 dec 2013). Graphical problem gone, but new, much more unpleasant problem emerged.
This thin client is connected to Windows Server 2008 R2 SP1, all updates are up-to-date. Terminal Server.
the steps:
- i connect from my machine (W7SP1x64 with latest updates) via RDP (mstsc.exe or tsmmc.mmc - doesn't matter) to the terminal server
- i open up the remote desktop services manager, right click on the user that's connected from the T410
- i hit "remote control" button
- for a moment i see some bits of user's desktop, but in less than a second my RDP session drops with the following error:
Problem signature:
Problem Event Name: APPCRASH
Application Name: mstsc.exe
Application Version: 6.2.9200.16398
Application Timestamp: 5036045e
Fault Module Name: mstscax.dll
Fault Module Version: 6.2.9200.16398
Fault Module Timestamp: 5035e59d
Exception Code: c0000005
Exception Offset: 00000000000f2220
OS Version: 6.1.7601.2.1.0.256.48
Locale ID: 1049
Additional Information 1: 2328
Additional Information 2: 2328419a4b40d8964e7f792f0ac157d5
Additional Information 3: 3197
Additional Information 4: 319796c94d8825616721d114b3479569
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
the problem is not present for the rest on the terminal users (that are connected from a unix thin clients), i remote control their session without any issues.
Please help me. We are building a new office and planning it for using PoE on every workdesk with your T410 Thin Client. But the fact that i can't manage them remotely brings me a lot of grief.

Hello again! I am sad to tell that my solution was not fully effective - i have got the new problem now
when i remote control session, it connects and works for some time, but at some point (which can be even a second from connection) it disconnects, throws me back to my admin session, and on the client side of t410 the following message appears:

Which RV220W VPN-setup do I choose in the following situation?

My RV220W has a fixed IP-address on its WAN and there is an ISP-provided FQDN with reverse lookup available. Is it possible to setup an IPsec VPN on this box that a Mac laptop can connect to the VPN from any location world wide that does not actively block VN traffic in some way?
I know a PPTP connection to the server on my LAN works, but I'd rather have an IPsec connection to the RV220W and turn the PPTP server on the host inside my LAN off.
If this is possible, what do I enter where in the wizard?
I have been unable to get this from the manual or by trying to find a recipe somewhere on the net,

It explains how to set up the RV220w for IPSec, and connecting using free IPSec clients on both Windows and MacOS.
https://drive.google.com/file/d/0B0EERf9TN4v1Ym9uaWRlMXhfVGM/edit?usp=sharing

RV220W VPN

Ugh. I've spent endless hours trying to get the VPN to work. I've done all the recommended actions for QuickVPN (run as Vista SP2, disable avast, enable windows firewall, disable windows defender, create windows ICMPv4 rules, turned on IPSEC services, disabled other network adapters) but I can NEVER connect. It always comes up with waiting for network.
I set up PPTP today. And it worked partially. I was able to access the RV220W but unable to browse any other networked devices or even access the internet. I ran the windows diagnostic tool and it said it was a DNS issue on the remote side.
Can someone please guide me before I end up ripping this device off the network? Much appreciated!

Troy,
What is your OS?
Does the RV220W have a static WAN IP?
Who is the ISP?
Where are you connecting FROM?
Does the local router have a different IP than the RV2220W?
Is the RV220W on the latest firmware?
- Marty

RV220W - VPN PPP & RDP problem

Similar Messages

Maybe you are looking for