Starting AnyConnect VPN through RDP Session

Hi,
We have AnyConnect (ver 3.1.01065) configured on our ASA5520 boxes. VPN is working fine from the desktop, but I also need the ability to establish a VPN connection through a RDP connection (i.e. I'm using RDP to connect to a PC which has AnyConnect installed on, then trying to establish a VPN connection).
I've downloaded the Cisco VPN Profile Editor, chaned the <WindowsVPNEstablishment> option to "AllowRemoteUsers". Then applied the profile to the relevant Group Policy. Connected VPN from the PC (not through RDP), so that it downloads the new profile, and then disconnected again.
However, I still can't start VPN through an RDP connection. (Error is "VPN establishment capability from a remote desktop is disabled. A VPN connection will not be established".)
I've checked the XML file on the local PC to confirm the profile has been downloaded (and is has, and I can see the AllowRemoteUsers option.
This also happened with the previous version of AnyConnect (3.0.xxxx).
The PC's local routing tables look fine, and I can't see any conflicts that would cause the RDP session to drop.
Also - If I connect VPN, then RDP onto the PC, both the VPN and RDP sessions work fine.
Any ideas would be appreciated!
Thanks
Tony

Hi Portu,
Thanks for your reply, and thanks for confirming that it works with AC 3.1 and ASA 8.4 (I'm using the same ASA version).
It looks like the issue was that I created the profile with the standalone Cisco VPN Profile Editor, saved it, uploaded it to the ASA, I then added a new profile on the ASA (in the Cisco AnyConnect Profiles section), and specified the file... however, it appears that I over wrote the uploaded profile, as the WindowsVPNEstablishment was set to LocalUsers. Once I changed it to AllowRemoteUsers and applied the config, then deleted the profiles from the client, it worked!
Simple mistake - but easily done!!
Thanks again
Tony

Similar Messages

ASA 5505 AnyConnect VPN Can RDP to clients but can't ping/icmp

Hello all,
I've been searching all day for a solution to this problem. I setup and SSL anyconnect VPN on my Cisco ASA 5505. It works well and connects with out a problem. However, I can't ping any internal clients, but I can RDP to them. It may be something simple and I would appreciate any help. Most of the time people end up posting their config so I will as well.
MafSecASA# show run
: Saved
ASA Version 8.2(1)
hostname MafSecASA
domain-name mafsec.com
names
interface Vlan1
nameif inside
security-level 100
ip address 10.4.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 7.3.3.2 255.255.255.248
interface Vlan3
no forward interface Vlan1
nameif dmz
security-level 50
ip address 172.20.1.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
domain-name mafsec.com
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
protocol-object udp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object udp
protocol-object tcp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_4
protocol-object ip
protocol-object icmp
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_4 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_3 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list outside_access_in extended permit icmp any any
access-list inside_split_tunnel standard permit 10.4.0.0 255.255.255.0
access-list inside_split_tunnel standard permit 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool SSLVPNPool2 10.5.0.1-10.5.0.254 mask 255.255.255.0
ip verify reverse-path interface outside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 7.3.3.6 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 10.4.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.4.0.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd option 6 ip 8.8.8.8 8.8.4.4
dhcpd address 10.4.0.15-10.4.0.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd lease 86400 interface inside
dhcpd option 3 ip 10.4.0.1 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.3055-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.3055-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSLVPN internal
group-policy SSLVPN attributes
dns-server value 8.8.8.8 8.8.4.4
vpn-tunnel-protocol svc
group-lock none
split-tunnel-policy tunnelspecified
split-tunnel-network-list value inside_split_tunnel
vlan none
address-pools value SSLVPNPool2
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username user1 password
username user1 attributes
service-type remote-access
username user2 password
tunnel-group SSLVPNGROUP type remote-access
tunnel-group SSLVPNGROUP general-attributes
address-pool SSLVPNPool2
default-group-policy SSLVPN
tunnel-group SSLVPNGROUP webvpn-attributes
group-alias SSLVPN enable
prompt hostname context
Cryptochecksum:3b16cbc9bbdfa20e6987857c1916a396
: end
Thank in advance for any help!

Your config actually looks good (you have the ACL that would allow the echo-reply back since you don't have inspection turned on) - are you sure this isn't a windows firewall issue on the PCs? I'd try pinging a router or switch just to make sure.
--Jason

RDP session fails with TermDD event id 56

I have a Wyse R10L thin client and I have configured the thin client with Static IP address,
I have a Windows Server 2008 R2 host system configured with FTE (Fault Tolerance Ethernet) network, and I have transition network Redundant link protector
SBFTF1010-130,
The SBFTF1010-130 is connected in-between the CISCO switch and thin client. The network connections are made like the FTE primary to Port#2 and secondary to Port#3 of RLP (redundant Link Protector).
Connected a normal CAT5 cable to Port#1 of RLP to thin client and established the RDP session of 2008 R2, and started working on the RDP session and removed a Port#2 cable and checked the LED status on the RLP. It switched to Primary to Backup network but
the RDP session got terminated which is not expected result.
When I check event log, it created an entry with event log “Event ID=56 The terminal server security layer detected an error in the protocol stream and has disconnected the client.”
Can you please help?
Regards
B.Akbar
B.Akbar

Thanks Jeremy for looking this issue.
Before posting this issue i have tried the link suggested by you and many people and it is not actually fixing my issue.
The details in event log says,
Log Name : System
Source: TermDD
Event ID:56
Level: Error
Binary data:
In Words
0000: 00040000 002C0002 00000000 C00A0038
0008: 00000000 C00A0038 00000000 00000000
0010: 00000000 00000000 D00000B5
In Bytes
0000: 00 00 04 00 02 00 2C 00 ......,.
0008: 00 00 00 00 38 00 0A C0 ....8..À
0010: 00 00 00 00 38 00 0A C0 ....8..À
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
0028: B5 00 00 D0 µ..Ð
I have tried updating so many Group Policy and Local Security changes but nothing helps to resolve the issue. Even i could reproduce this issue without the thin client and RLP hardware.
To reproduce the issue we need two systems configured with FTE on same network and RDP one system from other system. Once login to the RDP host system open a Ping window and ping anyone of the IP address continuously, pullout the Primary link of the network
cable from the system which you are using for RDP and check the ping continuous or not.The ping stops when you pullout the primary link of the network cable.
So i think this is not a specific product issue rather it is a common bug in Microsoft OS.
Please help me to address this issue as we are using wide range of thin client with RLP in our virtualization projects.
Regards,
B.Akbar
B.Akbar

VPN from an RDP Session

Hello there,
We are trying to connect to an anyconnect instance through an RDP session. We have no difficulty connecting, but once we do the RDP session is terminated. This makes sense in theory, but is there any way to avoid this? Enabling split-tunnel?
Any insight would be appreciated.

In the routing world, and configuring a GRE tunnel - you would get the same issue if you route the GRE end points into the tunnel, the tunnel cannot form - chicken and the egg.
I will not ask why you are soing this, but you will need to split-tunnel the traffic you need to encrypt, not the IP connection that the RDP session is created with.
HTH./

Start Agent Process failed ! Failed to logon a RDP session.

So, trying to run a basic load test and I'm gettin this error "Start Agent Process failed ! Failed to logon a RDP session." I've enabled windows remote management on the agent box, installed the Oracle ATS Agent and have it running under my ID (agent box), setup the agent box in the "Systems" menu and successfully ran a connection test.
It's got to be something small, and unfortunately the included documentation is confusing. It keeps referencing a process for getting the Oracle Load Test Agent service, however it doesn't exist. It's not where the docs say the installer should be, and it's not an included option of the full installer.
Any help or guidance you can provide will be greatly appreciated.

Hi,
Please anyone reply.....on this....!!!!!

Cisco AnyConnect VPN client and 256 AES encryption in IE8

Hey,
We have a site that we are trying to connect to with the AnyConnect VPN client version 2.5.3055 on Windows XP SP3. As soon as we enter the site info and hit select, it says a connection was unable to be established.
I believe this has to do with the encryption, its set up with 256 bit AES. We are only able to install IE8, which on XP only supports up to 128 bit encryption, so in IE8 the page will not load. To fix that issue we installed firefox which supports 256 bit encryption. We can get to the page there, but when we go to connect to the same site VIA the VPN client it still will not connect. It will work fine on a windows 7 box with IE9 installed from the same network.
My question mainly pertains to how the AnyConnect client connects on the back end. Does it use Internet explorer's SSL layer by default? Or does it have its own? If it connects through internet explorer, is there a way to change it to firefox so it will actually be able to open up a connection?
Thank you for your answers in advance,
John

Hey Jeff,
Thanks for answering that question. Hmm, so it doesnt go through the browsers SSL layer. We have systems on the same network (same proxy, firewall, vlan, etc). All the systems with windows XP SP3 and IE8/IE7 can not connect to the VPN (they arent even able to start the connection and ask for proxy/logon info.), all the systems with windows 7 and IE9 can. Same setups on each one as far as the security policies go as well. I thought it may have to do with the 256 bit encryption that they are using.
If thats not the case, what else could be causing the problem? weve tested it on about 5 XP machines and 5 Win 7 machines, same results on each. Connects on Win 7, does not connect on Win XP.
Thanks,
John

Cisco AnyConnect VPN won't install, says There is a newer version of the AnyConnect client already installed

I had an issue with my Cisco Anyconnect VPN not working, so uninstalled it. I've tried a new install and now I get the message "There is a newer version of the AnyConnect client installed" and it won't tell me install it at all. I've gone through various recommendations on the site included this :-
Go to "Regedit" and search for "Deterministic Networks" and delete it.
HKEY_LOCAL_MACHINE \SOFTWARE\Deterministic Networks
Search with the following keywords in the registry, under "Uninstall" or "Components" folders and delete any related entries.
Vpnapi
Vpngui
Cisco
CVPND
CVPNDRA
Ipsecdialer
Source: https://supportforums.cisco.com/message/3728011#3728011
But I've still got the same problem, and just cant find anything to help !

Disable Internet Connection Sharing (ICS) and then try You can disable ICS in two ways:
Per Adapter:
Click the Start button.
Click on Control Panel.
Click on View Network Status and Tasks
Click on Change adapter settings
Right-click the shared connection and choose Properties
Click the Sharing tab
Clear the Allow other network users to connect through this computer's Internet connection checkbox
Click OK
System Wide:
Click the Start button (Windows' orb)
Type: services.msc and press ENTER
Double-Click on Internet Connection Sharing (ICS)
Change Startup Type to Disabled
Reboot the computer
You can now try reinstalling the WiscVPN client again

Really Need Some Help with CME 8.6 using IOS as Firewall and Anyconnect VPN on Phones

Hello,
I have a 2911 Router with IOS Security and Voice enabled and we are using CME 8.6. I am using a built-in Anyconnect VPN on 3 phones that are for remote users and thus I needed to enable security zones on the router which works because the remote phones will boot up, get their phone configs and I am able to call those remote phones from an outside line.
The issue I am having is that when I try to dial a remote phone connected via the VPN through port g0/0 from and internal office phone, i.e., NOT involving the PSTN then there is no audio. It's as if no audio is going back and forth. When I take off the security zones from the virtual-template interface and the g0/0 interface then the audio works great and I can reach the phone from internal as I am supposed to.
Could someone take a peek at my security config and see why audio would not be traveling through the VPN when I have my security zones turned on?
clock timezone PST -8 0
clock summer-time PST recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.8.1 192.168.8.19
ip dhcp pool owhvoip
network 192.168.8.0 255.255.248.0
default-router 192.168.8.1
option 150 ip 192.168.8.1
lease 30
multilink bundle-name authenticated
isdn switch-type primary-ni
crypto pki server cme_root
database level complete
grant auto
lifetime certificate 7305
lifetime ca-certificate 7305
crypto pki token default removal timeout 0
crypto pki trustpoint cme_root
enrollment url http://192.168.8.1:80
revocation-check none
rsakeypair cme_root
crypto pki trustpoint cme_cert
enrollment url http://192.168.8.1:80
revocation-check none
crypto pki trustpoint TP-self-signed-2736782807
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2736782807
revocation-check none
rsakeypair TP-self-signed-2736782807
voice-card 0
dspfarm
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
vpn-group 1
vpn-gateway 1 https://66.111.111.111/SSLVPNphone
vpn-trustpoint 1 trustpoint cme_cert leaf
vpn-profile 1
host-id-check disable
voice class codec 1
codec preference 1 g711ulaw
voice class custom-cptone jointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone leavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice translation-rule 1
rule 1 /9400/ /502/
rule 2 /9405/ /215/
rule 3 /9410/ /500/
voice translation-rule 2
rule 1 /.*/ /541999999/
voice translation-rule 100
rule 1 /^9/ // type any unknown plan any isdn
voice translation-profile Inbound_Calls_To_CUE
translate called 1
voice translation-profile InternationalType
translate called 100
voice translation-profile Local-CLID
translate calling 2
license udi pid CISCO2911/K9 sn FTX1641AHX3
hw-module pvdm 0/0
hw-module pvdm 0/1
hw-module sm 1
username routeradmin password 7 091649040910450B41
username cmeadmin privilege 15 password 7 03104803040E375F5E4D5D51
redundancy
controller T1 0/0/0
cablelength long 0db
pri-group timeslots 1-12,24
class-map type inspect match-any sslvpn
match protocol tcp
match protocol udp
match protocol icmp
class-map type inspect match-all router-access
match access-group name router-access
policy-map type inspect firewall-policy
class type inspect sslvpn
inspect
class class-default
drop
policy-map type inspect outside-to-router-policy
class type inspect router-access
inspect
class class-default
drop
zone security trusted
zone security internet
zone-pair security trusted-to-internet source trusted destination internet
service-policy type inspect firewall-policy
zone-pair security untrusted-to-trusted source internet destination trusted
service-policy type inspect outside-to-router-policy
interface Loopback0
ip address 192.168.17.1 255.255.248.0
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description Internet
ip address dhcp
no ip redirects
no ip proxy-arp
zone-member security internet
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.8.1 255.255.248.0
duplex auto
speed auto
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
interface Integrated-Service-Engine1/0
ip unnumbered Loopback0
service-module ip address 192.168.17.2 255.255.248.0
!Application: CUE Running on NME
service-module ip default-gateway 192.168.17.1
no keepalive
interface Virtual-Template1
ip unnumbered GigabitEthernet0/0
zone-member security trusted
ip local pool SSLVPNPhone_pool 192.168.9.1 192.168.9.5
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:/cme-gui-8.6.0
ip route 192.168.17.2 255.255.255.255 Integrated-Service-Engine1/0
ip access-list extended router-access
permit tcp any host 66.111.111.111 eq 443
tftp-server flash:apps31.9-3-1ES26.sbn
control-plane
voice-port 0/0/0:23
voice-port 0/3/0
voice-port 0/3/1
mgcp profile default
sccp local GigabitEthernet0/1
sccp ccm 192.168.8.1 identifier 1 priority 1 version 7.0
sccp
sccp ccm group 1
bind interface GigabitEthernet0/1
associate ccm 1 priority 1
associate profile 1 register CME-CONF
dspfarm profile 1 conference
codec g729br8
codec g729r8
codec g729abr8
codec g729ar8
codec g711alaw
codec g711ulaw
maximum sessions 4
associate application SCCP
dial-peer voice 500 voip
destination-pattern 5..
session protocol sipv2
session target ipv4:192.168.17.2
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 10 pots
description Incoming Calls To AA
translation-profile incoming Inbound_Calls_To_CUE
incoming called-number .
port 0/0/0:23
dial-peer voice 20 pots
description local 10 digit dialing
translation-profile outgoing Local-CLID
destination-pattern 9[2-9].........
incoming called-number .
port 0/0/0:23
forward-digits 10
dial-peer voice 30 pots
description long distance dialing
translation-profile outgoing Local-CLID
destination-pattern 91..........
incoming called-number .
port 0/0/0:23
forward-digits 11
dial-peer voice 40 pots
description 911
destination-pattern 911
port 0/0/0:23
forward-digits all
dial-peer voice 45 pots
description 9911
destination-pattern 9911
port 0/0/0:23
forward-digits 3
dial-peer voice 50 pots
description international dialing
translation-profile outgoing InternationalType
destination-pattern 9T
incoming called-number .
port 0/0/0:23
dial-peer voice 650 pots
huntstop
destination-pattern 650
fax rate disable
port 0/3/0
gatekeeper
shutdown
telephony-service
protocol mode ipv4
sdspfarm units 5
sdspfarm tag 1 CME-CONF
conference hardware
moh-file-buffer 90
no auto-reg-ephone
authentication credential cmeadmin tshbavsp$$4
max-ephones 50
max-dn 200
ip source-address 192.168.8.1 port 2000
service dnis dir-lookup
timeouts transfer-recall 30
system message Oregon's Wild Harvest
url services http://192.168.17.2/voiceview/common/login.do
url authentication http://192.168.8.1/CCMCIP/authenticate.asp
cnf-file location flash:
cnf-file perphone
load 7931 SCCP31.9-3-1SR4-1S.loads
load 7936 cmterm_7936.3-3-21-0.bin
load 7942 SCCP42.9-3-1SR4-1S.loads
load 7962 SCCP42.9-4-2-1S.loads
time-zone 5
time-format 24
voicemail 500
max-conferences 8 gain -6
call-park system application
call-forward pattern .T
moh moh.wav
web admin system name cmeadmin secret 5 $1$60ro$u.0r/cno/OD2JmtvPq4w9.
dn-webedit
transfer-digit-collect orig-call
transfer-system full-consult
transfer-pattern .T
fac standard
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-template 1
softkeys connected Hold Park Confrn Trnsfer Endcall ConfList TrnsfVM
button-layout 7931 2
ephone-template 2
softkeys idle Dnd Gpickup Pickup Mobility
softkeys connected Hold Park Confrn Mobility Trnsfer TrnsfVM
button-layout 7931 2
ephone-dn 1 dual-line
number 200
label Lisa
name Lisa Ziomkowsky
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 2 dual-line
number 201
label Dylan
name Dylan Elmer
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 3 dual-line
number 202
label Kimberly
name Kimberly Krueger
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 4 dual-line
number 203
label Randy
name Randy Buresh
mobility
snr calling-number local
snr 915035042317 delay 5 timeout 15 cfwd-noan 500
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 5 dual-line
number 204
label Mark
name Mark McBride
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 6 dual-line
number 205
label Susan
name Susan Sundin
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 7 dual-line
number 206
label Rebecca
name Rebecca Vaught
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 8 dual-line
number 207
label Ronnda
name Ronnda Daniels
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 9 dual-line
number 208
label Matthew
name Matthew Creswell
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 10 dual-line
number 209
label Nate
name Nate Couture
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 11 dual-line
number 210
label Sarah
name Sarah Smith
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 12 dual-line
number 211
label Janis
name Janis McFerren
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 13 dual-line
number 212
label Val
name Val McBride
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 14 dual-line
number 213
label Shorty
name Arlene Haugen
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 15 dual-line
number 214
label Ruta
name Ruta Wells
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 16 dual-line
number 215
label 5415489405
name OWH Sales
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 17 dual-line
number 216
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 18 dual-line
number 217
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 19 dual-line
number 218
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 20 dual-line
number 219
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 21 dual-line
number 220
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 22 dual-line
number 221
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 23 dual-line
number 222
label Pam
name Pam Buresh
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 24 dual-line
number 223
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 25 dual-line
number 224
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 26 dual-line
number 225
label Elaine
name Elaine Mahan
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 27 octo-line
number 250
label Shipping
name Shipping
ephone-dn 28 dual-line
number 251
label Eli
name Eli Nourse
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 29 dual-line
number 252
ephone-dn 30 dual-line
number 253
ephone-dn 31 octo-line
number 100
label Customer Service
name Customer Service
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 32 octo-line
number 101
label Sales
name Sales
call-forward busy 214
call-forward noan 214 timeout 12
ephone-dn 33 dual-line
number 260
label Conference Room
name Conference Room
call-forward busy 100
call-forward noan 100 timeout 12
ephone-dn 100
number 300
park-slot timeout 20 limit 2 recall
description Park Slot For All Company
ephone-dn 101
number 301
park-slot timeout 20 limit 2 recall
description Park Slot for All Company
ephone-dn 102
number 302
park-slot timeout 20 limit 2 recall
description Park Slot for All Company
ephone-dn 103
number 700
name All Company Paging
paging ip 239.1.1.10 port 2000
ephone-dn 104
number 8000...
mwi on
ephone-dn 105
number 8001...
mwi off
ephone-dn 106 octo-line
number A00
description ad-hoc conferencing
conference ad-hoc
ephone-dn 107 octo-line
number A01
description ad-hoc conferencing
conference ad-hoc
ephone-dn 108 octo-line
number A02
description ad-hoc conferencing
conference ad-hoc
ephone 1
device-security-mode none
mac-address 001F.CA34.88AE
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:2 2:31
ephone 2
device-security-mode none
mac-address 001F.CA34.8A03
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:12
ephone 3
device-security-mode none
mac-address 001F.CA34.898B
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
ephone 4
device-security-mode none
mac-address 001F.CA34.893F
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
ephone 5
device-security-mode none
mac-address 001F.CA34.8A71
ephone-template 1
max-calls-per-button 2
username "susan"
paging-dn 103
type 7931
button 1:6
ephone 6
device-security-mode none
mac-address 001F.CA34.8871
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:7 2:31 3:32
ephone 7
device-security-mode none
mac-address 001F.CA34.8998
ephone-template 1
max-calls-per-button 2
username "matthew"
paging-dn 103
type 7931
button 1:9
ephone 8
device-security-mode none
mac-address 001F.CA36.8787
ephone-template 1
max-calls-per-button 2
username "nate"
paging-dn 103
type 7931
button 1:10
ephone 9
device-security-mode none
mac-address 001F.CA34.8805
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:5
ephone 10
device-security-mode none
mac-address 001F.CA34.880C
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:14
ephone 11
device-security-mode none
mac-address 001F.CA34.8935
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:3
ephone 12
device-security-mode none
mac-address 001F.CA34.8995
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:8 2:31
ephone 13
device-security-mode none
mac-address 0021.5504.1796
ephone-template 2
max-calls-per-button 2
paging-dn 103
type 7931
button 1:4
ephone 14
device-security-mode none
mac-address 001F.CA34.88F7
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:23
ephone 15
device-security-mode none
mac-address 001F.CA34.8894
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:26
ephone 16
device-security-mode none
mac-address 001F.CA34.8869
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:28 2:27
ephone 17
device-security-mode none
mac-address 001F.CA34.885F
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:11
ephone 18
device-security-mode none
mac-address 001F.CA34.893C
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:27
ephone 19
device-security-mode none
mac-address 001F.CA34.8873
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:27
ephone 20
device-security-mode none
mac-address A456.3040.B7DD
paging-dn 103
type 7942
vpn-group 1
vpn-profile 1
button 1:13
ephone 21
device-security-mode none
mac-address A456.30BA.5474
paging-dn 103
type 7942
vpn-group 1
vpn-profile 1
button 1:15 2:16 3:32
ephone 22
device-security-mode none
mac-address A456.3040.B72E
paging-dn 103
type 7942
vpn-group 1
vpn-profile 1
button 1:1
ephone 23
device-security-mode none
mac-address 00E0.75F3.D1D9
paging-dn 103
type 7936
button 1:33
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
transport input all
scheduler allocate 20000 1000
ntp master
ntp update-calendar
ntp server 216.228.192.69
webvpn gateway sslvpn_gw
ip address 66.111.111.111 port 443
ssl encryption 3des-sha1 aes-sha1
ssl trustpoint cme_cert
inservice
webvpn context sslvpn_context
ssl encryption 3des-sha1 aes-sha1
ssl authenticate verify all
policy group SSLVPNphone
functions svc-enabled
hide-url-bar
svc address-pool "SSLVPNPhone_pool" netmask 255.255.248.0
svc default-domain "bendbroadband.com"
virtual-template 1
default-group-policy SSLVPNphone
gateway sslvpn_gw domain SSLVPNphone
authentication certificate
ca trustpoint cme_root
inservice
end

I think your ACL could be the culprit.
ip access-list extended router-access
permit tcp any host 66.111.111.111 eq 443
Would you be able to change the entry to permit ip any any (just for testing purpose) and then test to see if the calls function properly. If they work fine then we know that we need to open som ports there.
Please remember to select a correct answer and rate helpful posts

Control what AnyConnect VPN clients can Access

Hello!
How do I ensure that my VPN users that are connected using AnyConnect VPN to my ASA5520 have the same access restrictions/permissions as those connected locally?
Assign a pool in the same vlan/subnet as those connected locally?
Any input helps. Thanks

Your annyconnect RA clients should have unique separate network from any other internal subnets and you will find much easier management and administration as soon as you start creating different RA tunnels for different purposes in future, at least this is my practice and find easy to administer and/or troubleshoot. If you decide using VPN tunnel network the same as an inside subnet you may encounter problems down the road which will be hard to troubleshoot.
Now you have VLAN10 subnet internally, if I understand correctly you want RA clients have the same access VLAN10 users have,my question to you is what type of access are you refering to? does VLAN10 users have access to certain internal networks or specific hosts and some don't? if this is so when you use vpn filters build the same access control you have defined for VLAN10 users, you don't necessarily have to create per user vpn filers but rather a group policy defining the permit access through the acl and apply it to the Annyconnect RA tunnel if the intend is for the whole tunnel group, just as shown in the RA vpn filter example link posted excluding the per user vpn filer.
Rgds
Jorge

Cisco Unified CM Administration is not working in RDP sessions .

Dear all.,
Cisco unified cm administration we are working in sandbox labs connected through vpn of Cisco. But we are not able to access through remote desktop sessions. is it any possible to access through remote desktp sessions..?

Hi
We are getting Cisco Unified CM Administration using sandbox labs. we are having a product for telecommunication . The name is CADEBILL. we are implementing the process from that product. we installed that product in a server. We have VPN through that sandboxlabs. That vpn is installed in local pc. From that local pc we will access the server in Remote desktop . in that server we are not able to install the anyconnect vpn . So this problem.
This is cisco unified CM version. System version: 8.6.1.20000-1

Problem using SunRay with Cisco AnyConnect VPN Client

I am using Cisco AnyConnect VPN Client Version 2.5.3046
I have a PC and a SunRay connected to my router. I use VPN to connect my SunRay and my PC to my work computer. My PC works fine, I am able to connect to the internet and also run cisco VPN to connect to my work computer. But when I try to use my SunRay, I get a window on the screen with the message:
VPN IKE Phase 1 agg I msg1This window keeps moving around on the screen. I am not able to connect my SunRay through VPN to my work computer. Any idea what could be wrong and how I can fix this?

2.2 is definitely better.
On one PC, I'm fine. On another -- very similar -- it tells me it can't start the VPN even after uninstalling and re-installing and everything else I can think of, with plenty of re-boots inbetween.
Aaaaarrrrrrggggggghhhh.

IP Phone SSL VPN through ASA

Im in the middle of configuring Ip Phone SSL VPN through ASA, got stuck on authentication.. When I enter username and password on the phone screen, i get "Username and password failed" message on the screen. However, in ASA logs I see the following line
Feb 16 2011 15:12:57 725002 85.132.43.67 52684 Device completed SSL handshake with client vpn:85.132.*.*/52684
Feb 16 2011 15:17:26 725007 85.132.43.67 52745 SSL session with client vpn:85.132.*.*/52745 terminated.
What does it mean? How can I turn on debugging to see what is going on?
Thank you in advance!

Hi,
If you're not using certificates in client authentication then the SSL handshake will complete before the user is requested to authenticate with username/password. If this authentication request fails you will see the SSL session terminated immediately following this failure (as in the logs you provided). Notice the 5 seconds between the SSL session establishment and termination, this is most likely when the user is being authenticated against the aaa server. If the phone is failing authentication against an external aaa-server you'll want to investigate the logs on that server to determine the root cause of the failure. The ASA can also provide confirmation of the authentication request/reject with the command 'show aaa-server'. If you want to see what's going on at an authentication protocol level you can enable several debugs including "debug aaa authentication|common|internal' and protocol specific debugs such as 'debug radius user|session|all' or 'debug ldap'.
Did this answer your question? If so, please mark it Answered!

Unable to ping device behind Cisco 3750 on the same inside VLAN via Cisco ASA 5505 Anyconnect VPN

Hi Guys,
I've been stuck with this for the last 2 days, and I thought to try and use Cisco's forum, I setup my home DC, and started having problems once I moved a Cisco 5505 behind a Cisco 1841 router (I wanted to eventually test DMVPN live on the internet,) I was no longer able to ping some devices, then as soon as I introduce a collapsed core/distribution switch, I'm also no longer able to ping the devices behind the Cisco 3750, I've attached a network diagram and the ASA running-config.
Everything seem fine internally with the exception of an intermittent network connectivity with a Citrix NetScaler VPX running on a VMware ESXi.
For some odd reason, I am able to ping the following, with no issues.
Cisco 3750 SVI (192.168.1.3)
CentOS web server (connected directly to the Cisco ASA 5505)
I have checked and enable the following:
Nat Exemption
Sysopt connection permit-vpn
ACL's
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
Added ICMP in the inspection policy
Packet-capture - Only getting echo requests.
Thanks in advance!

Hi,
I believe you have the problem with your no-nat configurations..... you to exempt NAT for the traffic from 172.16.10.0 (Anyconnect VPN pool) to 192.168.1.0/24 (Inside LAN) to make this work
object network acvpnpool
subnet <anyconnect VPN Subnet>
object network insidelan
subnet <inside lan subnet>
nat (inside,outside) source static acvpnpool acvpnpool destination static insidelan insidelan
Make sure that you are able to reach the GW/Inside ip adress of the firewall from LAN machine.... all routing in place properly..... Thanks!!!
Regards
Karthik

Unable to unistall Cisco AnyConnect VPN - please help

I have upgraded to Windows 8.1 preview on my Surface Pro. My Cisco AnyConnect VPN stopped working. When I uninstalled the software it left the ‘Cisco AnyConnect VPN Virtual Miniport Adapter for Windows x64’ under the network adapters in Device Manager. No matter what I do, I cannot uninstall it from there. I tried everything including uninstalling in safe mode. I says it uninstalled but still appears there. I believe because of this, my internet connection performance has decreased tremendously. It also disconnects and reconnects sometime after. My other computers work perfectly with maximum speed.
Please Help.
Thanks,
Mike

Windows Event Log detail as follows:
Faulting application name: vpnagent.exe, version: 3.1.4066.0, time stamp: 0x52211732
Faulting module name: Dbghelp.dll, version: 6.3.9600.16520, time stamp: 0x52e690ac
Exception code: 0xc0000005
Fault offset: 0x00029132
Faulting process id: 0x1e74
Faulting application start time: 0x01d02328f37bd890
Faulting application path: C:\Program Files (x86)\Cisco\Cisco AnyConnect Secure Mobility Client\vpnagent.exe
Faulting module path: C:\Windows\SYSTEM32\Dbghelp.dll
Report Id: 31beb6d1-8f1c-11e4-8278-54271ebdf9a6
Faulting package full name:
Faulting package-relative application ID:

Black Screen after logging in locally to Windows 7 that previously had an open RDP session.

Here is what happens. I leave my home computer on (running Windows 7 Ultimate) and sometimes I will remote to it from another location (work, friends house, or wherever). When I return home, I will go to login, the screen then goes blank (no mouse cursor
or anything). I have to do a cold boot to get back into Windows. This only happens if I ever RDP into it sometimes during the day. It seems random. I've tried logging off the RDP session, just closing it without logging off, nothing seems to be the answer
in that regard. It seems very random at times. I'll go a week and I can come home and it will login fine with no problems. Then the next week it starts giving me the black screen after I come home and login locally. I've seen several black screen issues here,
but usually they are getting it before logon. Anyone have a clue what might be causing this?

Hello,
The Windows Desktop Perfmon and Diagnostic tools forum is to discuss performance monitor (perfmon), resource monitor (resmon), and task manager, focusing on HOW-TO, Errors/Problems, and usage scenarios.
As the question is off topic here, I am moving it to the
Where is the Forum... forum.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Starting AnyConnect VPN through RDP Session

Similar Messages

Maybe you are looking for