RV320 - How to forward ports from WAN2
Hello,
I have 2 IP's on two different wan-ports. No i want to expose one machine from my LAN to the internet, on port 80 to do everything else with a reverse proxy. The other ip however must forward traffic from port 80 to a different machine:
<91.x.x.100>:80 -> forward to 192.168.0.20
<91.x.x.120>:80 -> forward to 192.168.0.110
I tried for two days now, and can't get it to work, here is what i tried so far:
One-To-One NAT from public ip to local machine - didnt work, i cant enter a wan ip address as public ip
Port Forwarding bound to a specific interface - Doesnt work, an interface is not selectable, although its stated in the docs
DMZ - Didnt work. Entered the local machines ip into the DMZ-Host field, set up the wan2 as DMZ with a correct ip, added access rules to the ACL, still no luck, all it did was, requesting both ips from outside, landed on the same machine.
I hope i didnt miss required information in this post, and hope that someone can give me an advice how to solve this.
Greetings
Nick
Was there any verification of this? I have an RV320 that we are attempting to use in the same fashion.
Our ISP is not capable of providing us with multiple addresses on the same network. So essentially we are stuck with 2 "isp's"
I know this issue could be resolved if we used another router, then set gateways on servers on the same network but I would prefer not to.
Wan1 - 198.xxx.xxx.205 - Forward to - Exchange 80/443/25/110
Wan2 - 198.xxx.xxx.146 - Forward to - Internal web app 80/443
Thanks for any help in advance!
Similar Messages
-
How to forward alert from one user to another user and how to reject?
Hi everybody.
How to forward alert from one user to another user and how to reject and how to complete alert?
Regards,
Vinay.What alert are you talking about? Which version of BOE / Edge do you use?
-
How to forward ports using Airport Extreme?
So,
I wanna forward some ports but every guide I find on the internet describes how to use the Airport Admin Utilty to do this. The problem is though that I can't configure my AE using AIrport Admin Utility; I need to use my Airport Utility instead. The only problem is that I don't know how to forward ports using Airport Utility.
Anyone?In AirPort Utility, Port Forwarding is called Port Mapping which is under the Advanced->Port Mapping tab.
-
How I forward text from one iphone 4 to other, only forward the calls
how I forward text from one iphone 4 to other, only forward the calls
you can't forward incoming texts to another phone automatically.
-
How to change port from 8080 to 80
Hi i need the help on Oracle 11g which is installed on RHEL5.
I am using apex3.2 , i had tried to change the application port from 8080 to 80 using exec dbms_xdb.sethttpport(80);
But there is no change on that, its not able to load on 80 port.
Please let me know if i am doing wrong
Details as follows
Operating System: RHEL5
RDBMS: Oracle11g
ApEx version: 3.2Thanks for your reply, i do not have that much of knowledge on linux could you please share your knowledge.
Here i have two users on my server one is root and another one is ipro. i had used ipro to install/configure oracle 11g and apex. As you said ipro user do not have a ownership to start a service on port 80. How can i provide the ownership on port 80 to ipro user.
Thanks and Regards
Maheswara -
How to forward port 25565?
I'm trying to run a minecraft server, and whenever I try to forward my port in port mapping in network preferences, I still get a "port 25565 is closed" on a port checking website. Putting my ip in the interenet browser does not load any setting either
Evan21437 wrote:
The main router is my 1 generation connected to my Ethernet/modem
So this TC gets the public IP address? Please check the summary page of the TC that it has a public not private wan IP.
The extend network TC is bridged so that doesn't matter. The only place you forward ports is the main TC if it is the main router of the network.
Post the screen shots of the setup of port forwarding on that. -
Cannot access forwarded ports from the internet
Hi all,
I have a Cisco 800 Series router that i configured to do some port forwarding. However i must have done something wrong, because i am unable to access the ports .
Here is the configuration file of the router.
Sorry it i pasted too much info, i'm new working with Cisco routers
Building configuration...
Current configuration : 9429 bytes
! Last configuration change at 13:39:12 PCTime Thu Jan 5 2006 by xxx
! NVRAM config last updated at 19:45:42 PCTime Mon Jan 2 2006 by xxx
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname pbr.mtn.w
boot-start-marker
boot system tftp c860-universalk9-mz.153-3.M.bin 255.255.255.255
boot-end-marker
logging buffered 51200
logging console critical
enable secret 5 xxx
no aaa new-model
memory-size iomem 10
clock timezone PCTime 2
crypto pki trustpoint TP-self-signed-2673109117
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2673109117
revocation-check none
rsakeypair TP-self-signed-2673109117
crypto pki certificate chain TP-self-signed-2673109117
certificate self-signed 01
30820250 308201B9 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32363733 31303931 3137301E 170D3036 30313032 31373232
35395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 36373331
30393131 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CD17 E55A2286 3F4D2F14 98499254 8DE9B540 7413A05A C229BD7E 72C6E7AA
7BD657C2 D824C6E4 0C0FD8AB 5EF6871B A28F298C 391DA225 FA4C92D7 5E3C6B06
B3447494 EA058319 72A69FEA 305751EE B7D7087A 406216C3 6CC14AB8 056B52F4
117366AD 531E0515 6801228D 7DAA8454 A00A880D 4023B8B3 983DE19C FB00F077
32450203 010001A3 78307630 0F060355 1D130101 FF040530 030101FF 30230603
551D1104 1C301A82 18706272 2E6D746E 2E772E79 6F757264 6F6D6169 6E2E636F
6D301F06 03551D23 04183016 80148E65 3A8C9B6B E552653E EA96DCD1 F13DD1F1
8198301D 0603551D 0E041604 148E653A 8C9B6BE5 52653EEA 96DCD1F1 3DD1F181
98300D06 092A8648 86F70D01 01040500 03818100 B6F568EE 3AFBBF7A B4DEC150
B6B8860B D953E444 8925C26C 4186AED4 8EAF9F2F D2F335E4 916F941C 1E831EEE
77C5A9A2 EB7EB7AA 540FF094 8FA28668 91C39BB2 2852DEB9 414DD37B EE984C20
CE755A14 37C41233 B0B93B55 52E15783 089B59AA AAE54620 352D3820 59DD24A3
F1E3EC91 CCDE72AA 7544C9C6 1C12EDAF 95767D97
quit
no ip source-route
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.1 192.168.1.219
ip dhcp excluded-address 192.168.1.241 192.168.1.254
ip dhcp excluded-address 10.10.10.21 10.10.10.254
ip dhcp pool ccp-pool1
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
ip dhcp pool GuestPool
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.80
dns-server 217.14.128.50 212.99.2.8 212.108.200.77 212.82.225.7
lease 7
ip cef
no ip bootp server
ip domain name yourdomain.com
ip name-server 196.44.250.214
ip name-server 196.44.250.215
ip name-server 41.223.226.30
ip name-server 212.118.241.1
ip name-server 213.157.176.2
ip name-server 62.128.175.14
license udi pid CISCO861W-GN-E-K9 sn FCZ161392V5
username xxx privilege 15 secret 5 xxx
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh version 2
class-map type inspect match-any ccp-cls-insp-traffic
match protocol cuseeme
match protocol dns
match protocol ftp
match protocol h323
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-protocol-http
match protocol http
policy-map type inspect ccp-permit-icmpreply
class type inspect ccp-icmp-access
inspect
class class-default
drop
policy-map type inspect ccp-inspect
class type inspect ccp-invalid-src
drop log
class type inspect ccp-protocol-http
inspect
class type inspect ccp-insp-traffic
inspect
class class-default
drop
policy-map type inspect ccp-permit
class class-default
drop
zone security out-zone
zone security in-zone
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
interface Null0
no ip unreachables
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description $ES_WAN$$FW_OUTSIDE$
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
duplex auto
speed auto
pppoe-client dial-pool-number 1
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip nbar protocol-discovery
ip flow ingress
ip flow egress
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 192.168.1.80 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly
zone-member security in-zone
ip tcp adjust-mss 1412
interface Dialer0
description $FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip flow ingress
ip nat outside
ip virtual-reassembly
zone-member security out-zone
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxx
ppp chap password 7 xxx
ppp pap sent-username xxx password 7 xxx
no cdp enable
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip flow-top-talkers
top 20
sort-by bytes
cache-timeout 20
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source static tcp 192.168.1.25 8890 interface Dialer0 8890
ip nat inside source static tcp 192.168.1.25 80 interface Dialer0 80
ip nat inside source static tcp 192.168.1.45 21 41.186.26.35 21 extendable
ip route 0.0.0.0 0.0.0.0 Dialer0
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip host 255.255.255.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^C---------------------------------------------------------------------------
NOTICE TO USERS
THIS IS A PRIVATE COMPUTER SYSTEM. Unauthorized or improper use of this
system may result in administrative or disciplinary action and civil and
criminal penalties.
Any or all uses of this system and all files on this system are monitored,
and recorded.
This system is the property of xxx .
Disconnect IMMEDIATELY if you are not an authorized user!
^C
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
privilege level 15
login local
transport preferred telnet
transport input telnet
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
endYou need...
Either a Fixed IP from your ISP, or a service like no-ip.org to look up your current IP.
How to find the "Outside" IP on that machine go here...
http://www.whatsmyip.org/
If there's a Router involved at home then incoming ports must be directed to the proper local IP.
Setup Sharing on the home Mac. -
How to forward port to internet with Time Capsule
I'm using a Buffalo Technologies Linkstation to provide web access to my files from remote locations. I need to forward TCP port 9000 to the Linkstation's IP address which ia 100.0.1.196. Can anybody explain how to do that in the Apple utility?
Launch AirPort Utility, select your device and click manual setup.
Select the INTERNET pane, and then select the NAT tab.
From here, click the CONFIGURE PORT MAPPINGS button.
Click the + at the bottom of the window, choose the appropriate service, enter the ports you need to forward, enter the correct IP address and so on.
Click CONTINUE at the bottom to set up a name for this service (just something to tag it so you know what it is later) and you should be all set. The utility will prompt you to reboot your Time Capsule when you're all done. -
How to forward port for remote viewing...?
Since getting a Time Capsule I have been unable to use my SlingBox remotely. After doing some research I figured out that I have to forward a port...but i have no idea how...or what port to forward.
Can someone help me out here?Use Airport Utility. Click on the Manual Setup button, then click on the Advanced icon in the toolbar. Click on the Port Mapping tab then click on the [+] button to add a new configuration. Use port number 5001 for both TCP and UDP ports in the Public and Private fields. Use the IP address you have assigned to your Airport Express that you've connected to the Slingbox. You will find this all outlined in the Slingbox documentation PDF that came with the device. You can also find it at the Slingmedia website.
-
How to forward workitem from one user to another user inbox
Hi Experts
I have one problem in workflow. I need to forward work item from one user inbox to another user inbox.
Please can any one tell me procedure how to do this?
Regards
Ramesh
<Thread locked. Please do not duplicate questions in several forums - this one also posted in BPM and Workflow>
Edited by: Mike Pokraka on Aug 3, 2008 11:38 AMHi,
check these steps:
Configuring the SAP inbox for automatic mail forwarding.
1. Go to SAP Inbox (Transaction Code SBWP).
2. Go to Settings u2018Office settingsu2019. A pop up will appear
3. Choose u2018Automatic forwardingu2019 tab.
4. Click on u2018Createu2019 button.
5. Enter the mail address to which you want to send mail in u2018Forward tou2019 field.
6. Select u2018Internet Addressu2019 from the drop down in the field right of the u2018Forward tou2019 field.
7. Update the time period as desired.
8. Ensure that u2018Forward all documentsu2019 is selected.
9. Ensure that u2019Also place in inboxu2019 is selected.
10. Click the green check mark to save private office settings.
Regards,
Joy. -
How To Forward Ports on Your Router
1. What does it means, i tought i mean set a port to a spesic thing ( FTP, IP-voice, ) and what you want the "PORT" to point to? Im a wrong... i know i can do this in my router...
But what is it, how do i configure it, what should i think about doing it, and why do i use it for?
This topic first appeared in the Spiceworks Community1. What does it means, i tought i mean set a port to a spesic thing ( FTP, IP-voice, ) and what you want the "PORT" to point to? Im a wrong... i know i can do this in my router...
But what is it, how do i configure it, what should i think about doing it, and why do i use it for?
This topic first appeared in the Spiceworks Community -
do i have to use JNI for linux serial port access bcos the com pai i downloaded from sun works only for windows, except i have the old one.
the trick am trying toplay is to use the tty command in linux somehow in the code but i have lots of diffuculties there
any help?where did u get this very unromantic site from, cant pick my answers from it..any other assistance
thankx -
How to forward email from primary account - email settings screen is missing!
I have escalated your issue. An official employee will reply. Please check back every once in a while for a reply by one of them.
This question has been asked 100 times but the answer doesn't work. I use:-> My Account-> Users & PreferencesUnder my user name (which says "Primary User"), I'm supposed to see "Basic and Email Settings". I see only "Basic Settings". I am the primary user, the only user. I tried logging off and on using the user name and the comcast.net email address and both show I'm the primary user but no email settings. Where are the email settings so I can forward my email?
-
How do you forward ports?
I cannot seem to find any help as to HOW to forward ports--I have been using bittorrent and it works fairly well, but I think it might perform better if I could only forward to a better port.
Opinions?
Advice?Do you have a router? If so you can set up port forwarding in the router. Consult the User Guide for it. It should provide instructions on how to access the router via your web browser and how to set up port forwarding.
-
How to do port forwarding from wla2-g54l Buffalo bridge to mac mini
Hi,
I am trying to get Azurus to remove the "firewall block" message and I think I have narrowed it down to port forwarding.
I have set up port forwarding from my X modem to the Airport Xpress base station. I have then set up the port forwarding from the base station to the buffalo.
The problem I have had is setting up the wla2-g54l to forward the same port to the mac mini....
any Ideas? Not much luck on the Buffalo website.. and I have RTFM. Many times!
Cheers
Mac Mini G4 1.2Gz Mac OS X (10.4.8)It sounds like your set-up is in a horrible mess with 3 levels of NAT going on.
What you should really have is the X-Modem configured in it's default mode "Modem Mode" where there will be no need to do any port forwarding as the modem is acting as a pure modem without having any influence over ports.
Then the Airport express should be configured to "Distribute IP addresses" so that the Airport is acting as a router. I presume that you use the Buffalo unit as a repeater for the AIrport so you should set-up WDS so that both are on the same network. Then your computers will all be using IP addresses in the 10.0.1.x range as issued by the Airport. You can then configure the Airport to directly forward ports to the IP address of your computer. Therefore only one instance of NAT and only one set of port forwarding rules.
Maybe you are looking for
-
Hi all, I get the error message below halfway through the process when I am trying to run an add/update graph for my data store. The error log doesn't specify which record causes the error to arise. Anyone have any idea on how to solve the issue? ERR
-
Variable field in Header for every new page
Hi Friends. I am printing a new page on every new material no encountered . At the same time the HEADER has a field called Container name which is different for each material so this header field needs to be update each time when a new page is calle
-
Global Property not visible inside a BLT called from another BLT
Hi, I have created a Global Property SID to indicate the System ID so a BLT can use it (e.g. in file names). This executes correctly (MII 12.0.2). However, now I call this BLT from within another BLT, and that time the SID is marked as error ("invali
-
DW CS 5.0 crashes when using spry:if
Hi there, while trying to edit <tr> in code view by putting spry:if="'{ds_RowCount}' != '0'" DW crashes System: Win 7 x64 12 GB RAM DW 11.0 Build 4993 Spry Framework 1.6.1 page is not as much complex 5 spry xml recordsets and clean xhtml 1.0 strict m
-
Restoring photos with all adjustments maintained to new mac
I recently got a new iMac i7 with Snow Leopard so I installed Aperture 2 on it and upgraded it to the latest release 2.1.4 I backed up all the photos from Aperture 1.5.6 running on my G5 to a vault on an external HDD and then restored the vault on Ap