S750 Vista Configuration "Full Range Speakers"

Hello Everyone
Couple of days , I bought this Speakers and was wondering about this option whether to Tick them or not? I am talking about Speaker setup in Vista.
I am using X-Fi Xtreme Music card in Vista 64 bit edition along with S750 speakers. While Configuring my speakers from Audio Panel , I selected 7.1 speakers , optional speakers(Selected All of them), Finally it's asking me to select whether speakers support Full Range Speakers or not.
Please help me, whether i should select them or not. Previously i used T7900 and i know those are not Full Range Speakers. So i deselected them and continued. Here i am confused becoz i guess these are quite high end speakers , so i can select or not.
And also do these speakers capable of outputting a low frequency 20khz signal.
Thanks in advance
Omaha

Hi,
I can confirm you that selecting "Full Range Speakers" is wrong. This means that you allow the transmission of the full spectrum into the plugs connected to the speakers (front speakers for instance). Full spectrum ranges from low frequencies to high frequencies. For sure the seven speakers reproduce medium- to high-frequencies. The subwoofer reproduces low frequencies : 20Hz to something like 200Hz. The other speakers take care of the rest: 200Hz to 40kHz.
Concerning the power problems of these speakers you're right! I bought at the very beginning the Creative Cambridge SoundWorks 5.1. After 8 hours they were not working anymore. I received new ones and after a while was informed by Creative that some models were defecti've. Mine was of course! I had to return the speakers and I got the 6.1 instead. They were working perfectly! I decided to sell them and buy the S750 (7.1 and wireless remote). Sometimes when I power them on there is a cycle power off/power on/reset. I loose all settings...
Apart from these power issues there are very good speakers!!! The quality is incredible even while listening music, watching DVDs / Blu-Rays or playing games....
Regards,
Vincent

Similar Messages

Turn on Full Range Speakers and Bass Redirecti

I have the Logitech X-530 (5.) speaker system connected to my X-Fi XtremeMusic sound card. In the Vista Speaker Setup, it says to select "full-range speakers." Am I supposed to select the speakers Also, I have Bass Redirection turned on in the X-Fi audio console, since apparently it's supposed to make the subwoofer work better, is this true

As far as I know, the default "Bass Redirection" scheme that comes with Sound Blasters will redirect bass from the 5 channels to the subwoofer. Not the opposite. Also notice, that most speakers have a built-in crossover network that does just that. So even if you did redirect the bass to the speakers from the soundcard it would end up in the subwoofer. However when doing the redirection on the soundcard in the digital domain, they have to normalize the signal to avoid clipping. This explains the "lower" bass level you are experiencing with bass redirection set to on. If your speakers didn't have a cross-over network, you wouldn't hear anything from the sub unless you enabled "bass redirection"?Now I don't think that behaviour would change in games, but games do tend to have more "bassy" sound. My suggestion is to keep "Bass Redirection" off under all circumstances and use the Equalizer or the Subwoofer volume knob (most 5. systems have one) to bring the level to your liking. PS:? The X-Fi also has a "+5dB Bass Boost" option to alleviate the effects of normalization, which you can experiment with.

Full range/Large speakers and missing Bass on X-Fi

Hi all, I have an annoying problem with my x-fi xtremegamer. My 5.1 speaker setup is quite special because it has a full range frontal speakers (large speakers) with their own sub so I would like the bass redirection to work only in center a surround channels. You can achieve this through the win 7 speaker config or the thx console of your x-fi selecting both full range speakers and bass redirection.
I prefer this config instead of redirecting bass from all channels because in this way you most of mp3 and music files play directly ?from the full range frontal speakers while 5.1 movies or games still sounds very good and plenty of bass in all channels.
The main problem is that I can't get any bass from the frontal speakers after each reboot. Bass redirection from center and surround channels works perfectly but it's impossible to get any bass from frontal channels although deactivate the bass redirection. No bass at all!!!.
The only way I found to solve it, is to reset the speakers size configuration but it's quite annoying: I have to config them as small speakers, confirm, and after that re-config as a full range (each reboot). After doing that the sound systems works great, with bass redirection only in the speakers I want to, and full range sound through my frontal speakers.
Any ideas? I tested it with 2.8.5 driver and Pax Master Audio DVD 20. Thanks!

bump

The Firefox opening page no longer has the full range of Google links.

My prior version of Firefox had a full range of Google links at the top of the central page (including images, news, etc.). Is there any way to install this on version 4? I used this feature frequently Thanks in advance for your help.

I am guessing you are using a Firefox default of: http://www.mozilla.com/en-GB/firefox/central/
Note if you use the Google search from the search bar, that is top right, alongside where you type web addresses; you will get a more standard Google page, rather than a branded firefox page.
I tend to use http://www.google.co.uk/ you may of course choose nd bookmark any google search page you like, and if you wish you could set google as your home page.
*See [[how to set the home page]]

How can I change the Settings to Full range in AE?

I need to work in my new project in Full range. Is there any way to change the import-, project- and rendersettings to Full range?
Thanks Ali

Hi Todd,
we are working with Alex Prores 4444. For some VFX-shots we made pregradings. After finishing the work in AE and exporting Prores 4444 and re-importing the files in "Baselight", the saturation and Gamma was not the same like the once we exported. So now we are looking for a solution for this problem. And some people were saying, that this is becouse we are working with legal and not Full-range. That is the reason why I would like to find out correct the workflow in Fullrange.
Thanks
Ali

Guide in configuring number range by billing type in SD

Hi gurus,
Hope you can assist me in configuring number ranges by billing type (e.g. F2, G2, L2, etc) in SD. Our Accounting people find it hard to account the completeness of the transactions because we are only using one range for the RV (SD docs). We would like to setup a separate series per billing type.
Your immedaite assistance is highly appreciated.
Frances

Dear Frances,
1st Part
Go to, T. Code: SNRO
Insert, Object: RV_Beleg
and Click Tab: Number ranges (just above the Field: Object)
On to next screen, Click Tab: Intervals (with pencil-icon)
Here, maintain your Number ranges, that you wanna assign to your Billing Doc. Types, i.e. F2, G2, L2 etc..
2nd Part
Go to, T. Code: SM30
Insert, Table/View:
and click Tab: Maintan (down, at screen)
On to next screen, maintain entries as:
Sales Org + Dist. Chnl + Sales Doc. Type (i.e. Billing Doc.) + IntNR (as maintained in 1st Step)
Best Regards,
Amit

What does event type "configuration full" mean?

Hello,
thanks in advanced for any comments.
I recieved an email from our 6500 alerting me that the confiuration is full, i assumed it meant the start-up config, but it isn't that large..
COR1VSS2#dir system:
Directory of system:/
    2 dr-x           0                    <no date> memory
    1 -rw-       59020 May 11 2011 18:42:04 -04:00 running-config
   12 dr-x           0                    <no date> vfiles
No space information available
COR1VSS2#
thanks again for your time,
greg

thanks for that, but it wasn't tthe error.. here is some copy/pasting:
    Subject:     System Notification From COR1VSS2 - configuration:full - 2011-05-12 13:00:00 GMT-04:00
2011-05-12 13:00:00 GMT-04:00
Configuration
configuration
full
Cisco Systems
Catalyst 6500 Series Switches
thanks anyway yjdabear
greg

Can't configure 7.1 speakers correctly (all speakers with same outpu

(I'm using Windows XP Pro with, Soundblaster X-Fi XtremeGamer and Gigaworks S750)
I'm trying to configure my Creative Gigaworks S750 speaker system for listening to Music but I can't seem to get the sound configuration that I would like.
I have the speaker system connected to my computer (with all 3 connectors) and when listening to Music I would like to have the same amount of volume in each speaker. Or to treat all speakers on the left as a single front speaker, and all speakers on the right as a single front speaker.
Right now, no matter how I tune the software/hardware I always get a movie surround style sound. Most of the sound is coming from the Center, then the left right and the middle and back speakers have barely any sound coming from them.
Hardware-wise:
I have already minimizes the volume on the center channel on the hardware volume control that comes with the speaker system and also adjusted the center/rear volume to Maximum.
I have also tryed the 5.->7. and 6.->7. up mix feature.
Software-wise:
Every software that comes with the speaker system is installed. I use "Entertainment mode" when listening to music and in that mode I have tried:
- Adjusting the speaker mode to 2./4./5./7.
- Turned the CMSS3D on/off
- Adjusting to "Gigaworks S750" in the THX menu
- Listening to the Speaker assignment in the THX menu and all the speakers give the same amount of noise there
I have also tryied changing speaker modes in the Speaker configuration in Windows and that doesn't do anything.
I've tried both Winamp and Windows Media Player.
How can I fix this?
P.s.: Don't get me wrong, I still want the surround for when playing games and watching movies. That feature works very well.

set the speaker switch to direct not 5.1->7.1 and 6.1->7.1. set cmss3d to stereo expand.

Can't configure 7.1 speakers correctly (all speakers with same output)

(I'm using Windows XP Pro with, Soundblaster X-Fi XtremeGamer and Gigaworks S750)
I'm trying to configure my Creative Gigaworks S750 speaker system for listening to Music but I can't seem to get the sound configuration that I would like.
I have the speaker system connected to my computer (with all 3 connectors) and when listening to Music I would like to have the same amount of volume in each speaker. Or to treat all speakers on the left as a single front speaker, and all speakers on the right as a single front speaker.
Right now, no matter how I tune the software/hardware I always get a movie surround style sound. Most of the sound is coming from the Center, then the left right and the middle and back speakers have barely any sound coming from them.
Hardware-wise:
I have already minimizes the volume on the center channel on the hardware volume control that comes with the speaker system and also adjusted the center/rear volume to Maximum.
I have also tryed the 5.1->7.1 and 6.1->7.1 up mix feature.
Software-wise:
Every software that comes with the speaker system is installed. I use "Entertainment mode" when listening to music and in that mode I have tried:
- Adjusting the speaker mode to 2.1/4.1/5.1/7.1
- Turned the CMSS3D on/off
- Adjusting to "Gigaworks S750" in the THX menu
- Listening to the Speaker assignment in the THX menu and all the speakers give the same amount of noise there
I have also tryied changing speaker modes in the Speaker configuration in Windows and that doesn't do anything.
I've tried both Winamp and Windows Media Player.
How can I fix this?
P.s.: Don't get me wrong, I still want the surround for when playing games and watching movies. That feature works very well.

set the speaker switch to direct not 5.1->7.1 and 6.1->7.1. set cmss3d to stereo expand.

Audigy 2 ZS Platinum Vista 32bit full support

I would like to know if there will ever be full support drivers for the Audigy 2 ZS Platinum card and the I/O box in Vista 32 bit's? I am looking for the ability to use my 6. speakers correctly and being able to record through Line-In on the card. I would hate to think I will have to go to a competitor for a card that works fully in Vista.

He didn't ask this in 2005, he's registered in 2005, he asked this a month ago (just look again back, I made the same mistake too )?About some replies:Yes the audio?stack in Vista must be very difficult to handle, but the companies had MONTHS, there has been A LOT since Vista's Beta versions and RC etc has been around. Everyone had enough time. I just can't play music correctly because of the current Vista drivers. Furthermore, I can't play my favorite game because some sort of application cslled audiodg eats lots of CPU while anything is playing through my sound card: not a good idea for games as they REALLY doN't run smoothly this way. What I want is not an immediate support, but a well planned approximate date for the new, clean, smooth drivers for Vista. Ok, maybe they are not ready and won't be ready until September, so I'll go back to XP. Or they are maybe ready and the developers are making the last adjustments and the driver's coming in a week or two, so I'll stick to Vista. Creative NEEDS to give this information to the customers, no one has to wait with bogus drivers. I'm not blaming Creative for having their drivers not ready, I understand that, it's technically difficult, but they should at least inform us about when will the drivers be ready.

How to configure full tunnel with VPN client and router?

I know the concept of split tunnel....Is it possibe to configure vpn client and router full tunnel or instead of router ASA? I know filter options in concentrators is teher options in ISR routers or ASA?

I think it is possible. Following links may help you
http://www.cisco.com/en/US/products/hw/routers/ps274/products_configuration_example09186a0080819289.shtml

No audio in Windows Vista from my external speakers

when using BootCamp (on the OS side), i can hear my audio through my external speakers, but when i go to the WIndows Vista side, i only get audio through the monitor itself. what can i do to fix it so that it all come through the external speakers?
thanks for any advice

It's hard to know exactly which it is at this point. It could be one of two things. The speakers have failed or the jack detect pin located inside the headphone jack has failed. A non-functional jack detection pin would cause the system to route audio to the headphone jack constantly instead of the internal speakers.
If you want to be absolutely certain it is not a software issue (corrupted registry possibly), you can try the system recovery making sure to backup your files. I suspect this is a hardware issue, but it could very well be a corrupted registry causing the jack detection pin not to be read properly.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Windows Vista configures ITunes everytime I launch it.... Help :-)

So.....
Everytime I launch ITunes, Windows Vista configues it and reinstalls files....
I have checked the support pages and deleted a file as mentioned there, but it didn´t help the problem.
What can i do to sort this issue? Everytime I want to launch ITunes I need to spend 10 minutes waiting for Vista to configure and install.
Please help

The "Program Files (x86)" is only installed for 64-bit systems.
If you have a 32-bit system, open "My Computer" and check the folders on your "C" drive for "Program Files" (No "(x86)" in the file name.)
Once you find the iTunes application file, right-click on it and select the "Send To" option. From the drop-down menu, choose "Desktop" to create a shortcut on your desk top. (Make sure that you have deleted any old shortcuts before doing this.)
This will get iTunes to launch quickly, but there are still functions that do not work properly - file associations seems to be one.

How do I use the full range of Typekit fonts?

I want to use a couple of Typekit fonts (Calluna and Minion) that are not part of the Web Font library.
Is this now a feature in Muse CC or do I have to use a widget, such as this ...
Using Full Typekit Fonts in Adobe Muse CC - Widget by MuseThemes.com on Vimeo
Also, if I wanted to use another font ... such as Apercu ... not in the Typekit library, how do I do this?
Thanks very much
Simon

Hello Simon,
As of now Adobe only has visual support for the web font library. However you CAN use your type kit fonts. You can use a widget like the video posted describes, however you can also just use custom CSS in the page properties meta data.
It would look something like this:
<style>
p {
font-family: 'proxima-nova';
font-weight: 300;
font-style: italic;
h1{
font-family: 'proxima-nova';
font-weight: 600;
font-style: italic;
</style>
Attached are pictures explaining how to integrate type kit with the muse header custom html:
Navigate to typekit and create a new kit, make sure the domain YOUR site will be published on it selected. The star denotes any page.yourdomain.com.
After you click continue Adobe will give you some custom JQuery, a type of Javascript. Copy it and place it in your page properties > meta data <head> tag as shown below.
Add your desired fonts to the kit you created. After you select the style you want, click "using font in CSS" in the top left menu. A pop-upp box will appear with some code. Copy the bottom one to your clipboard.
Paste into the meta data head tag WITH <style> before and </style> afterwards. h1 denotes heading one, p denotes paragraph etc. The font-weight is the style, when you browse typekit it will tell you the wights; ie proxima nova semibold is 600, light is 100 etc. Font-style is the style: italics, bold etc. When adding this attributes, make sure they end with a semicolon (;).
Now the fun part: click on your text and go to the text menu. The very last field has a number or letter combo, h1, h2, p etc. These are the text styles that you inputed! If you want the text to correlate to you h1 code, then tag it h1. If you want iit to correlate to you p code, tag it p etc. ALL of your h1 will look the same and all of your p will look the same.
They will NOT be visible in the editor or preview, but only when published to your domain.
If that is too much work, just use the widget =).
Let me know if you have any Q's!
Cam
PS: sorry it was so choppy, I couldn't find a good video so I had to snap some quick screenshots.

AIR for mobile does not support the full range of icons. How can we include them?

The range of icon sizes suppoted by the <icons> attribute of the Main-app.xml seems quite limited.
For example, we are getting ready to launch our app in the Amazon app store, which has a wide range of different icon sizes for their devices:
https://developer.amazon.com/sdk/fire/cx-guidelines.html#IconSizes
But the majority of them fail when you try to include them in a build:
42x42, 62x62, 75x75, 78x78, 80x80, 90x90, 118x118, 121x121, 125x125, 134x134, 155x155, 159x159, 188x188, 210x210, 252x252, 284x284, 322x322, 365x365, 425x425, 675x675
Is there a way to add them to the .apk package that will be accesible to the application?

Hi,
If you feel that the number of icon sizes available are limiting you, please log a feature request for supporting more icon sizes on https://bugbase.adobe.com.

S750 Vista Configuration "Full Range Speakers"

Similar Messages

Maybe you are looking for