Sampling Inspection at variable rate during Receiving process

Hello,
We would like to perform sampling inspection during receipt process, actually we perform sampling for couple of supplier, the QA procedure is to inspect 10% of the total qty( we don't have lot/serial control set for items), if any failure then need to increase sampling rate to another by 10%.
As I understand Quality module in 11.5.10 allows for sampling at receiving process. But I am not sure, does it allow for above requirement to perform at different sampling rate based on failure.
Looking forward for your expert comments.
Thanks,

In quality module, you can setup rules that can alter the sampling rate. It is called skip lot inspections.
e.g. you can say that
* inspect 1 in every 5 shipments.
* But if any shipment is found bad, inspect 3 in every 5 shipments.
* Once 10 consecutive inspections are successful, then revert back to 1 in every 5 shipments.
Keep in mind the functionality works on number of receipts - not quantity in each receipt.
First you have to enable your org for skip lot inspections
Then you define a skip lot process code. This is where you define your logic/rules.
Then setup your sampling collections plan.
Hope this answers your question
Sandeep Gandhi
Omkar Technologies Inc.
Independent Techno-functional Consultant

Similar Messages

"Internet Mail - Problem during delivery processing" email received

Every email I'm receiving as of this morning is accompanied by an email from [email protected], entitled "Internet Mail - Problem during delivery processing"
Is this an issue on the Mac server side or a problem with my Mail app?
Many thanks in advance.

My Wife and I both have an Ipad and an iPhone, I use an iMac and my wife a MacBook Pro.
I have this problem with all my devices.
My wife has NOT got this problem.
We both use a [email protected] email acount.
Just compared the settings:
For "Incoming server" I have p03-imap.mail.me.com
My Wife has p02-imap.mail.me.com .... and has not got this problem.
I have setup a new rule for incoming mails (for the meantime):
move all incoming emails from [email protected] to trash and delete it.
Works fine for now,......until APPLE deals with the problem.
Message was edited by: RTONLINE

Rejections during in-process inspections

hi, is any std report available to find what are the produts rejected during in-process inspection,(at which operation) against each prod order? also can we know how many products passed without defect (after in-process insp) during in-process inspection against prod order?

Dear,
Do the defect recording at that time craete automatic notification then you will get this report in QM10 and QM11.
Else use the report QA33.
Regards,
R.Brahmankar

HT201210 Hi. During the process of updating my ipad to IOS 6 utilizing iTunes, I received the error #1602. I tried the update procedure again, this time itunes does not recognize the devise. The pad is displaying USB connecter to iTunes. Does anyone recom

Hi. During the process of updating my ipad to IOS 6 utilizing iTunes, I received the error #1602. I tried the update procedure again, this time itunes does not recognize the devise. The pad is displaying USB connecter to iTunes. Can anyone recomend a fix?
Thank you

There is only one fix now. The message on the screen means that you have to restore the iOS software on the iPad now. Read the part at the very end about using recovery mode.
iTunes: Restoring iOS software - Support - Apple
About the error code.....
Error 1600, 1601, 1602
Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
If needed.....
Additional Information
If your device is continually restarting, not responding, or showing the Apple logo with no progress bar or a stopped progress bar, place the device into recovery mode and try restoring again.

Changing sample rate during acquisition

I need to programmatically change sample rate during acquisition: My application involves sampling at slow rate most of the time but during "region of interest" I need to change sampling rate to fast (close to max rate of board).

I think it's also possible to use the same (high) sample rate during your
complete acquisition, but in the case you need the 'slow' rate only take
from the array sample 0, 10, 20 etc. or any number you prefer.
In the end I think you want to make sure your computer doesn't have to work
that hard all the way, or if you want to save the data, it's not that big...
If I'm wrong, please tell me.
Ron@ld
Lancer schreef in berichtnieuws
506500000008000000DF570000-1027480788000@exchange.ni.com...
> I need to programmatically change sample rate during acquisition: My
> application involves sampling at slow rate most of the time but during
> "region of interest" I need to change sampling rate to fast (close to
> max rate of board).

An error has occurred during report processing. (rsProcessingAborted)

Access Web Databases and SSRS
Issue:
After creating an access web database, such as Contacts Web Database in SharePoint 2010 we receive the following error when trying reports. This only happens on the Address Book, Phone Book, and Contact List reports. The Contact
Details and Printable Labels reports both work. The reports do not begin to error until data is added to the database (no errors initially).
I have duplicated this across all of our environments with the same results and get similar results when adding a Projects Web Database.
Environment:
Prod:
3 WFE Servers – SP 2010 sp1
3 App Servers – SP 2010 sp1
2 SQL Servers – 2012 sp1
QA:
3 WFE Servers – SP 2010 sp1
3 App Servers – SP 2010 sp1
2 SQL Servers – 2012 sp1
DEV:
1 WFE/App Server – SP 2010 sp1
1 SQL Server – 2012 sp1
Background
SSRS was installed following recommended guidelines and can be verified to be working. http://blog.helloitsliam.com/Lists/Posts/Post.aspx?ID=66
Error full text
Microsoft SQL Server Reporting Services
An error has occurred during report processing. (rsProcessingAborted)
The Group expression for the grouping ‘Group1’ contains an error: Request for the permission of type 'Microsoft.Office.Access.Server.Security.AccessServicesPermission,
Microsoft.Office.Access.Server.Security, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c' failed. (rsRuntimeErrorInExpression)

Found the answer
here.
In short, SSRS 2012 installation missed a couple of config entries. You'll have to add them yourself:
Open C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\15\WebServices\Reporting\rsreportserver.config. Search for the <Data> tag and add this entry:
<Extension Name="ADS" Type="Microsoft.Office.Access.Reports.DataProcessing.AdsConnection, Microsoft.Office.Access.Server.DataServer, Version=14.0.0.0, Culture=Neutral, PublicKeyToken=71e9bce111e9429c" />
Open C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\WebServices\Reporting\rssrvpolicy.config.
Search for <NamedPermissionSets> and add this entry:
<PermissionSet
class="NamedPermissionSet"
version="1"
Name="ReportExpressionsDefaultPermissionSet">
<IPermission class="SecurityPermission" version="1" Flags="Execution" />
<IPermission class="Microsoft.Office.Access.Server.Security.AccessServicesPermission, Microsoft.Office.Access.Server.Security, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c" version="1.0" Flags="CalculationCallback" />
</PermissionSet>
In the <CodeGroup>node, around line 70, find and change PermissionSetName from “Execution” to “ReportExpressionsDefaultPermissionSet”

Error during the Process of Netting - No Identifier Found TPM_TRG136

Hi All
During the process of doing Netting , the system is popping up an error message as - No Identifier found. The message error is TPM_TRG136.
Can anybody suggest the solution for the error.
Ram K

Hi @artem98765,
Welcome to the HP Forums!
It is a terrific place to find answers and suggestions.
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
I grasp that when you tried to do a recovery back to factory you received the error incomplete recovery.
As you did not state if how you were doing the recovery I will include documentation for the process along with a troubleshooting document.
HP PCs - Performing an HP system recovery (Windows 8)
HP PCs - Troubleshooting HP System Recovery Problems (Windows 8)
If you are still unable to complete the recovery please contact HP support for further assistance.
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

DYNAMIC_CALL_FAILURE Error during proxy processing An exception with the ty

Hi,
SRM 7.0 contains 2 clients:
Sender: 100 for EBP, logical system is CLNT100
Receiver: 200 for SUS, logical system is CLNT200
both the clients are connected through PI 7.0, logical system of PI is CLNT001.
From SPROXY of 100EBP, i'm executing the outbound proxy, in moni sent msg success.
In PI also msg is processed.
But in SUS200, it is showing below error msg:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIProxy</SAP:Category>
<SAP:Code area="ABAP">DYNAMIC_CALL_FAILURE</SAP:Code>
<SAP:P1>UNCAUGHT_EXCEPTION</SAP:P1>
<SAP:P2>CL_BBPX_TRADING_PARTNER_SUS_IN</SAP:P2>
<SAP:P3>EXECUTE_ASYNCHRONOUS</SAP:P3>
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Error during proxy processing An exception with the type CX_BBPX1_STD_MESSAGE_FAULT occurred, but was neither handled locally, nor declared in a RAISING clause Application Error</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
Pls help in resolving the same....
tnx n rgds,
balu

Hi,
How did you solve the issue? Can you please provide the solution.
Thanks,
-Devi Swain

Application error occurred during request processing webdynpro

Hi all,
I have developed one sample web dynpro application( welcome). when was deploying the welcome application on the j2ee engine using NWDS. It is giving the fallowing error i.e.
500 Internal Server Error
Application error occurred during request processing.
Details: com.sap.tc.webdynpro.services.exceptions.WDRuntimeException: Failed to create deployable object 'local/Welcome' since it is not of a Web Dynpro object.
Exception id: [02004C4F4F50005C0000000A0000091800042D3A2DDDDEDB]
Please help me how to deploy this application successfully.
Regards,
Deviprasad.

Hi Deviprasad,
Check out this link
Re: Internal Server Error 500
Regards,
Prateek

HT201413 i tryed to restore my phone but it turns of during the process and an error happens so what should i do

i tryed to restore my phone but it turn off during the process and an error happens so should i do ?

Hello there, VladlsSwag.
The following Knowledge Base article provides some steps for troubleshooting your issue:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Particularly:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
My issue is still not resolved. What do I do next?
Contact Apple Support.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Different schedule in terms of payment during sales process

Dear experts,
One of our international customer is having one requirement for having "Various schedule in different terms of payment". Meaning, they want to collect the advance (Down payment) from customers in various schedules during sales process itself. If customer doesn't pay the advance amount then, system should not allow the further sales process like delivery creation, picking and packing.
Example, client wants to receive the advance amount from customer in following schedules
1. During sales order creation - 30%
2. During production order process - 25%
3. then, during delivery creation stage - 25%
4. And as regular after creation of invoice remaining amount 20% client wants to collect from customer.
Is it possible to set this setting with block of sales process. I need experts opinion.
Thanks for your cooperation.
Warm Regards,
VEL

Hi,
You can achieve it through billing plan,
In billing rule speciefy your percentage
OR ELSE
You can achieve it through payment terms
In payment terms speciefy installment percentage
Kapil
Edited by: Julius Bussche on Jan 27, 2010 1:05 PM
English grammar corrected. Please do not use SMS-txt...

Various schedule in terms of payment during sales process

Dear experts,
One of our international customer is having one requirement for having "Various schedule in different terms of payment". Meaning, they want to collect the advance (Down payment) from customers in various schedules during sales process itself. If customer doesn't pay the advance amount then, system should not allow the further sales process like delivery creation, picking and packing.
Example, client wants to receive the advance amount from customer in following schedules
1. During sales order creation - 30%
2. During production order process - 25%
3. then, during delivery creation stage - 25%
4. And as regular after creation of invoice remaining amount 20% client wants to collect from customer.
Is it possible to set this setting with block of sales process. I need experts opinion.
Thanks for your cooperation.
Warm Regards,
VEL

Hi,
You can achieve it through billing plan,
In billing rule speciefy u r percentage
OR ELSE
You can achieve it through payment terms
In payment terms speciefy installment percentage
Kapil

Timer fires during trigger processing on web

I was looking for a way to augment the default behaviour
of a hierarchical tree. The trouble is clicking in a tree can fire various combinations of WHEN-MOUSE-CLICK, WHEN-TREE-NODE-SELECTED, WHEN-TREE-NODE-EXPANDED,
WHEN-TREE-NODE-ACTIVATED, WHEN-MOUSE-DOUBLE-CLICKED. I wanted to trigger some action after they had finished firing but as I didn't know which would fire last, where to put the code ?
The solution I found was to start a 1 ms timer in WHEN-MOUSE-CLICK (which always fires first), gather information from the other triggers into a variable, and do my processing in WHEN-TIMER-EXPIRED. This worked fine on client/server but when I deployed it on the web I found the timer expired between WHEN-MOUSE-CLICK and WHEN-TREE-NODE-SELECTED (triggered by a single click).
My understanding of timers is that, however short their duration, they should not expire during trigger processing. Have I got this wrong or is this a bug ?
It seems to work OK with 5 ms but I would like to know what is going on.
(f6i patch 7)

All,
as promised, here's an answer from development. Duncan said it already, but here's the long version
1). Regarding timers in general. 1ms timers fire on the server (effectively,
at the time the timer is created in a trigger, we put a timer macro on the
stack so that that next time we go for input (after we've processed all
of the events we've already gotten at that point), it will act as if the timer
has expired. This, as you know, prevents us from doing round-trips to the
client when people are simply creating a timer to get around some of the
restricted built-in/trigger issues. Any timer of longer than 1ms will get
created on the client and thus cause round-trips. We have no plans to
bump that threshhold up, so people could use 2ms timers if they wanted...
2). Regarding timers expiring during trigger processing. It is true in both
client/server and web that we will not expire a timer while a trigger is
firing. However, the order in which the user will see events (and thus
which triggers will fire in) can vary. In the example that was given,
the user (double)clicks on a node in the tree on the client. The first
mouse click causes a message/event to be sent immediately to the
server, which ends up causing the when-mouse-clicked trigger to fire.
As soon as that message is sent, the server starts processing that
trigger. In the meantime, the client may decide that it needs to send
other messages (such as when-node-selected, etc.). However, until
the server sends a return-message to the client asking for more input,
this won't get sent. Now, the server fires the when-mouse-click trigger,
and as part of it a timer gets created. There are two possible scenarios
here.
In the first scenario, the timer is 1ms, and thus is handled on the
server. Thus, when the trigger ends, the server sees if there is any more
input to be processed, and sees that the timer has expired (because, as
I explained above, this gets put directly onto the macro stack). Thus, the
timer expired trigger fires. After that trigger fires, the server sees that it
has no more input waiting, and sends a message to the client telling it to
send more input. At that point, the client can send whatever other events
it has queued up (such as the when-node-selected) and we carry on.
In the second scenario, the timer is more than 1ms long. In this case, when
the trigger says to create a timer, the server queues up a message to send
to the client telling it to create a timer. When the rest of the trigger is complete
and the server sees that it has no more events to process, it sends this timer
creation message to the client at the same time it asks the client to give it
more events. The client sends the when-node-selected event, the server
processes it, and eventually asks the client for more input. By then, the
timer has expired and then the timer message gets sent to the server.
In neither of these cases does the timer trigger fire in the middle of
another trigger that is already firing, it is simply that the separate triggers
might fire in a different order because of the order that the underlying
events are processed. In client/server, the process is effectively the same
as the 2nd scenario above, because the timer is handled by the toolkit, just
like the other events, and thus the message for the timer expiring will get
sent to Forms after any of the events related to the mouse click. But again,
the rule about timers firing during trigger processing is not violated, it is just
that there is a break between triggers that can allow a 1ms timer to fire
'sooner' on the web than in client/server.
Fran

Repetitive "Exception during idle processing" log message from servermgrd

Hello,
I'm at my wit's end trying to find the answer to this issue, and I don't have any clue where to begin. In /var/log/system.log, I'm receiving the following message approximately once per minute:
Apr 17 13:51:21 www servermgrd\[83317\]: Exception during idle processing: * -\[NSCFDictionary setObject:forKey:\]: attempt to insert nil value (key: FilePath)
There are usually no other messages in the log near these errors; when other messages are nearby, they are self-explanatory and appear unrelated. The message never changes except for the time stamp and the process ID for servermgrd.
Any suggestions on where to begin would be extremely valuable. Thanks!

check with this:
<a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/05a3d62e-0a01-0010-14bc-adc8efd4ee14">https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/05a3d62e-0a01-0010-14bc-adc8efd4ee14</a>

Tomcat : exception during startup processing

Hi !
I have this exception when trying to start Tomcat :
Starting service Tomcat-Standalone
Apache Tomcat/4.1-dev
Starting service Tomcat-Apache
Apache Tomcat/4.1-dev
Exception during startup processing
java.lang.reflect.InvocationTargetException:java.lang.NoSuchError:java.lang.Runtime: method addShutdownHook(java/lang/Thread;)V not found
at org.apache.catalina.startup.Catalina.start (Unknown source)
at org.apache.catalina.startup.Catalina.execute(Unknown source)
at org.apache.catalina.startup.Catalina.process(Unknown source)
at java.lang.reflect.Method.invoke (Native Method)
at java.lang.reflect.Method.invoke (Compiled Code)
at org.apache.catalina.startup.Bootstrap.main (Compiled Code)
I have imported the jdni.jar in my jdk 1.2.2, and set variables (PATH, JAVA_HOME, CATALINA_HOME, CLASSPATH), and I don't have Apache.
Please, help me if you have any idea !
Gaelle.

Hi,
I got this error too when I installed Tomcat 3.2.1 on JDK1.2.2. But when I changed by JDK to 1.3.1 and altered the tomcat.bat file to take JAVA_HOME to jdk1.3.1 path, it worked fine.
Change your JVM to JDK1.3.1 and this should get rid of the error.
Regards,
Seetesh

Sampling Inspection at variable rate during Receiving process

Similar Messages

Maybe you are looking for