SAPConsole and the Bell Signal

Hey Folks,
I'm developing some custom ABAP transactions to use with SAPConsole through a Georgia Softworks (GSW) telnet server / mobile client. I've followed the instructions layed out in SAP note 371838 and have succeeded in generating the bell signal through a GSW desktop client. However, it does not work on my mobile device. I'm using an Intermek CK31 handheld computer/scanner running Windows CE 4.2 and using the GSW Universal Mobile Client for device type ARMv4i.
Can anyone give me some guidance in regards to setting/configuration of the device or GSW software. Should I be using a different GSW client? FYI: I tried using the enhanced client for the Intermek CK30, but I couldn't even get it to function on the mobile computer.
Thanks for your help.
Jim M

Problem was due to faulty operating system / GSW client on remote device

Similar Messages

I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I cannot connect to the internet wirelessly. the wireless light has a fast green blinking light. how can I fix the router?

I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I am unable to connect to the internet wirelessly. The wireless light is blinking green very quickly and I connect and disconnect from the network constantly. How do I get the router to work properly

Hello James,
The flashing WLAN light means activity (data getting transferred). Try disconnecting all your devices and check whether the light is still flashing or disconnect the router from internet and do the check.
Do you have your SSID as linksys or the default one? If your neighbor has the same SSID, then traffic could result from your neighbor's one. Try changing your SSID and password. Make your security WPA/WPA2.
Hope this helps,
Thanks
Vijay

Ipad 2 upgraded to iOS 8.0.2 and the cellular signal doesn't work. Have to restart the unit to work with cellular signal. After a while it goes off and no service indication appears.

Ipad 2 upgraded to iOS 8.0.2 and the cellular signal doesn't work. Have to restart the unit to work with cellular signal. After a while it goes off and no service indication appears.

iPad 2, Since upgrading to iOS 8.0.2 the cellular signal indicates I do not have a SIM card. Monday spent hours on the phone with Apple support, backed up my iPad, reset all settings, reloaded my iPad and it still tells me I don't have a SIM card. Tuesday went to AT&T and got a new SIM card on the advice of apple support. It worked perfect until this morning and the NO SIM CARD notice reappeared. Never ever had any problem until the upgrade. I find it inexcusable that Apple refuses to address the issues they caused, iOS 8.0.2 is the Ebola of iPad 2 world. I dont have any cellular service after wasting two days trying to address and fix a problem Apple is responsible for. It's obvious Steve Jobs is no longer running the company. Furious & fustrated. How does Apple expect anyone who uses an iPad 2 for work, to remain a customer who will return to their products?

Command a ventilator with USB6251 and The Daq Signal Accessory

Hello,
I would like to make a school project using Labview and the USB6251 connected to the Daq Signal Accessory Board.
The Labview program must read continuously the temperature from the temperature sensor (AI channel 4, internally connected) from the Daq Signal Accessory Board. When the temperature reaches an established value, then a led on the front pannel must be turned on and an output singal from the Daq must start a ventilator connected to the Daq which cools down the sensor and then stops.
Would it be possible to do something like this? Even if I generate a square signal and the ventilator runs only on the high state of the signal. The ventilator requires at least 120 mV DC current. I am afraid that if I take such current from the Daq I might damage the device.
Thank you.
Solved!
Go to Solution.

I guess you mean 120 mA DC current . If you look at your daq board spec you will find that the max current are far bellow 120 mA. This is true for both analog out and digital out. Take a look at this site it may help out some. http://www.me.umn.edu/courses/me2011/robot/technotes/motorcontrol/motorcontrol.html cool site. If you want speed control you have two options PWM or regulating the motor voltage.
Good luck
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

What is the difference between signal processing tooklit and the advanced signal processing tooklit

Hi
I am work on a project with Labview 7.1 now and want to calculate the FFT based on
the Welch method. In my full version Labview, there is a signal processing tooklit
I install it but did not found that welch.vi. Is it means that except for signal processing
tooklit, there is another advanced one and I should pay more money for it, Or,
Should I update my Labview version to 8.0 and the software will support the tooklit?
Thanks a lot!

Hi dec04009 ,
When you say "Signal Processing toolkit", do you mean the Signal Processing Palette, that is included in LabVIEW Full?
LabVIEW has signal processing VI's, those are supported in later versions, like 8.0 or 8.2. Since LabVIEW 8.0 there were added many new mathematical functions. Take a look at this:
http://zone.ni.com/devzone/conceptd.nsf/webmain/bf49f9b8951a89f3862571840057b2c7
The Advanced Signal Processing Toolkit, has advanced features, like wavelets analysis, JTFA
http://sine.ni.com/nips/cds/view/p/lang/es/nid/1395
I'm not familiar with the Welch Method, but I found this in the functions of the LabVIEW 8.2:
http://zone.ni.com/reference/en-XX/help/371361B-01/lvanls/welch/
Hope this help.
Tania Lozoya

My volume keeps turning off and on by itself. It vibrates and the bell picture pops up without me doing anything. It doesn't matter if I have the selector switch on or off for volume. Any ideas?

Can anyone help me keep my volume from turning on and off automatically?

Hi Friend,
I have faced this issue yesterday, but just for one app. Then I went to Notifications Center, turn all the settings of that app to off then turn it on again. Rebooth the device (press and hold Home and Sleep button simultaneally until turns off the device and appears the Apple logo), then everything works at a glance.
Hole it helps

Solution: How to find the phone signal in fringe areas

This is not so much a question but a solution I accidentally found.
If you are in a weak signal area and the phone is stuck on "searching" or says "no signal" and you need to get it to find that phone signal all you need to do is push the phone shut off button on the top of the phone by holding it down until the shut down screen appears, but don't move the slider to shut down the phone.
Next, wait a few seconds and the phone signal will show up. In really fringy areas you may need to try twice.
There is no question that this phone is much more able to get weak signals than my 3GS.

Hi, thanks for the information, but i have figured out the following additional settings that are required to be made :
1) from upper menu, select the "Environment" to :- Business blueprint
2) then select any folder on the left-hand-side
3) Now, click on 'Structure' tab
....and now, follow the steps as answered by you.
Also, after you have opened up the "History" dialog box ..... click on the "show scope info' ...... it will give you the entire change log.
Thanks,
PS : step no. 1) is very important.

My iphone is stuck on silent! even though it is not on silent mode, even when i lock the screen it doesn't make the loking sound and the keys don't make sounds when i tye even though the settings are on for the sounds.

my iphone is stuck on silents, the side switch flicks but nothing happens PLEASE HELP!

hi iphone users i have had the same problem with the no sound issue i have a little tweek that will gain all sound back on any iphone it worked for me heres what to do if it works for you let me no because ino its a nightmare having a phone with no sound 1st thing go to settings general accessibility scroll down assistive touch click it on when you get the white dot click on it you will have 4icons click on the device 1 you will then see volume up and down and also have little bell make sure volume is up and the bell is not muted there you quick fix for sound also you dont have to keep the assistive on you can then turn it off you will have all sounds incoming call the lot enjoy hope it helps

Have one WiFi signal into the apartment for my Air, and another wifi signal for my 5c phone plan. Both from the same provider. Expensive. Is there a way to 'combine' WiFi signals so I pay only for one, but can get on the Internet with my Air?

Have one WiFi signal into the apartment for my Air, and another wifi signal for my 5c phone plan. Both from the same provider. Expensive. Is there a way to 'combine' WiFi signals so I pay only for one, but can get on the Internet with my Air?

Roamingnome, thanks for your response. Although I have been a Bell (Canada) customer for my WiFi signal for years, the 5c and its necessary mobility plan, is very recent. Some years ago, Bell supplied its own ‘router’ for my computer, and claimed that it was possible to get their WiFi signal only with the router they supplied. When I recently received the 5c, I wondered if the plan it requires, which is within the much wider, overall Bell zone, could be used somehow to get my Air online - some sort of tethering? - that allows me to give up the Air WiFi service and router all together, but still get the Air connected. Here in Canada, Bell Mobility and other Bell services are very separate. Any suggestions appreciated.

I am using the Order Analysis Toolkit and want to get more information about the compensation for "Reference Signal Processing", which is scarce in the manuals, the website and the examples installed with the toolkit.

I am using the Order Analysis Toolkit and want to get more information about the compensation for "Reference Signal Processing", which is scarce in the manuals, the website and the examples installed with the toolkit.
In particular, I am analyzing the example "Even Angle Reference Signal Processing (Digital Tacho, DAQmx).vi", whose documentation I am reproducing in the following:
DESCRIPTIONS:
This VI demonstrates how to extract even angle reference signals and remove the slow-roll errors. It uses DAQmx VIs to acquire sound or vibration signals and a digital tachometer signal. This VI includes a two-step process: acquire data at low rotational speed to extract even angle reference; use the even angle reference to remove the errors in the vibration signal acquired at normal operation.
INSTRUCTIONS:
1. Run the VI.
2. On the DAQ Configurations tab, specify the sample rate, samples per channel, device and channel configurations, and tachometer channel information.
NOTE: You need to use DSA PXI-447x/PXI-446x and PXI TIO device in a PXI chassis to run this example. The DSA device must be in slot 2 of the PXI chassis.
3. Switch to Extract Even Angle Reference tab. Specify the number of samples to acquire and the # of revs in reference which determines the number of samples in even angle reference. Click Start to take a one-shot data acquisition of the vibration and tachometer signals. After the acquisition, you can see the extracted even angle references in Even Angle Reference.
4. Switch to the Remove Slow-roll Errors tab. Click Start to acquire data continuously and view the compensate results. Click Stop in this tab to stop the acquisition.
ORDER ANALYSIS VIs USED IN THIS EXAMPLE:
1. SVL Scale Voltage to EU.vi
2. OAT Digital Tacho Process.vi
3. OAT Get Even Angle Reference.vi
4. OAT Convert to Even Angle Signal.vi
5. OAT Compensate Even Angle Signal.vi
My question is: How is the synchronization produced at the time of the compensation ? How is it possible to eliminate the errors in a synchronized fashion with respect to the surface of the shaft bearing in mind that I am acquired data at a low rotation speed in order to get the "even angle reference" and then I use it to remove the errors in the vibration signal acquired at normal operation. In this application both operations are made in different acquisitions, therefore the reference of the correction signal is lost. Is it simply compensated without synchronizing ?
Our application is based on FPGA and we need to clarity those aspects before implementing the procedure.
Solved!
Go to Solution.

Hi CracKatoA.
Take a look at the link bellow:
http://forums.ni.com/ni/board/message?board.id=170&message.id=255126&requireLogin=False
Regards,
Filipe Silva

IPhone 5S lost voicemail and when I tap vm icon the phone diales voicemail and gets busy signal. No other options show.

iPhone 5S lost voice mail and when I tap vm icon the phone dials voice mail and gets busy signal. No other options show.
started yesterday. No voice mail at all. When I tap the voice mail icon the phone immediately dials some number and that number rings busy. I can't select anything else. Using Virgin mobile/ I am stumped.
I have already tried a soft boot... power and home button....
Help!

Other than changing the SIM card, you don't mention any troubleshooting you did with your phone.
If you haven't already, try the following steps as needed:
Settings > General > Reset > Reset Network Setting.
Reset phone - press both home and sleep/wake buttons until the Apple logo appears.
Restore phone in iTunes using a backup
Restore in iTunes as a new iPhone
IF the last step doesn't fix it, there is a hardware problem and you should make an appt. with an Apple Store Genius Bar. The fact that you haven't dropped the phone by no means rules out hardware issues.

I am trying to hook my macbook pro to a sony bravia TV via DVI to HDMI cable and the TV will not recognize the signal. The same set up has worked with three other, though different televisions. Any thoughts?

I am trying to hook my MacBook Pro to a Sony Bravia TV via DVI to HDMI cable and the TV will not recognize the signal. I have used the same setup with three other TV's, each a different brand with no problem. Any ideas?

Is the TV set to take input from the HDMI connection?
On your computer, if you open the Displays preferences and do not see an Arrangement tab (or there is an Arrangement tab that shows only a single monitor) then there is something physically wrong with your connection. Try clicking Detect Displays just to see if the computer can now sense the presence of the connection. Check your connections.
If you do have an Arrangement tab, and it shows two screens, then click Gather Windows to bring the TV's Displays preferences on to your main screen if the TV is not yet showing an image. Set the proper resolution (probably 720p, 1080i, or 1080p). Set the refresh rate (probably 60Hz) if that preference is shown. You should see a picture at this point. I recommend turning off mirrored displays if it is enabled.

I am trying to use the RS232 to control a circuit board. It would have to simultaneously output SerialClock, DataIn, and Chip Select signals, while also receiving DataOut signals; therefore 4 signals total. Does anyone know if it this is possible?

I am trying to splice 4 wires out of the RS232 serial cable (the 9-pin type) and wire them to a circuit board. The 4 wires would control 4 signals: DataIn, DataOut, SerialClock, and ChipSelect. The serial clock would synchronize the DataIn and the ChipSelect is asynchronous. DataOut must coincide with SerialClock also; therefore there are 3 signals that must be able to switch concurrently. All the handshaking enabled by RS232 is thus unnecessary in my opinion. Does anyone know of how this can be done?

I am trying to splice 4 wires out of the RS232 serial cable (the 9-pin type) and wire them to a circuit board. The 4 wires would control 4 signals: DataIn, DataOut, SerialClock, and ChipSelect. The serial clock would synchronize the DataIn and the ChipSelect is asynchronous. DataOut must coincide with SerialClock also; therefore there are 3 signals that must be able to switch concurrently. All the handshaking enabled by RS232 is thus unnecessary in my opinion. Does anyone know of how this can be done?

Can anyone tell me or give me a link to the latest response from Apple regarding very real weak wifi signal on what seems to be a batch of both the new ipad and the earlier Ipad2. I have just bought a 2nd hand ipad2 and it has a very weak wifi signal

Over the last week or so I have been trawling the internet looking for references to weak wifi signals on the Ipad2 and was staggered by the sheer quantity of people who seem to have identical issues, not just with the ipad2 but also with the new ipad. What annoyed me most from reading the reams upon reams of comments made on the Apple community forum is the fairly large number of people who seemed to believe that 'these' people were either just moaners and wingers or else they must have something wrong with their router set-up rather than a serious fault with their ipad and it seems all because there ipad in question works like a dream.
Obviously I can only speak from my experience, and that is, I have an ipad2 32GB with wifi, purchased about 6 months ago and it works like dream with a good 2-3 bar wifi signal through 2 thick stone walls over 30 feet away. My router is a standard one supplied by my broadband supplier compatible with all 'g','b' and 'n' equipment. However, over a week ago now I bought second hand genuine ipad2 16GB with wifi from a close friend who has just purchased a new ipad3 to replace his old ipad2 (had it for over a year so no longer under warranty). When I started it up downstairs from my router, where I always use my other ipad2 which has a very strong wifi signal, I discovered that the new secondhand ipad2 I had purchased couldnt find a network signal at all. So after doing network resets and all other 'fixes' on the device recommended, I took it upstairs to my office where the router is based and found that the device could now locate the network, but the signal was lost over only 12 feet from the router!
I quizzed my good friend about this issue and he informed me that it has always been like this since he first purchased it and he never thought that it was a fault, it was just the way it was. When he first aquired the device he did think at the time that this distance was poor, but thought nothing of it as he didnt have any other ipad to measur ethe signal strength against, and as his router was in his living room anyway he nothing of it. Fair enough.
So, there we have it. One ipad2 with a very good wifi signal and another ipad2 with a very poor wifi signal running off the same router, both with the same IOS 5.0. ?
As well as all of the other isues that customers have picked up on, such as 'death grip' (which I must say does appear to happen, but personally i dont think that this is a serious issue if you are aware of this issue and have a strong signal anyway), my experience seems to be a good example of a 'duff' wifi ipad versus a 'great' wifi ipad', an issue confirmed by complaints from a fairly large number of customers who have also reported the same or similar weak wifi signals with both the ipad2 and the ipad3. So, as this shows the weak wifi signal is a very real issue it seems on a batch of ipad2 and 3's, which to my logic is obviously a hardware issue on a batch of early ipad2's and not a software one, otherwise all ipad's would suffer this problem! So, is it a faulty antenna or a faukty network card in an early batch?
So, the bottom line now is, of course, firstly, how can I get Apple to fix my other ipad2 when the warranty has run out? Any suggestions anyone?
Personally I think good Apple customer service should offer a recall with a replacement on this apparent batch of ipads, dont you?

Greetings,
I've never seen this issue, and I handle many iPads, of all versions. WiFi issues are generally local to the WiFi router - they are not all of the same quality, range, immunity to interference, etc. You have distance, building construction, and the biggie - interference.
At home, I use Apple routers, and have no issues with any of my WiFi enabled devices, computers, mobile devices, etc - even the lowly PeeCees. I have locations where I have Juniper Networks, as well as Aruba, and a few Netgears - all of them work as they should.
The cheaper routers, Linksys, D-Link, Seimens home units, and many other no name devices have caused issues of various kinds, and even connectivity.
I have no idea what Starbucks uses, but I always have a good connection, and I go there nearly every morning and get some work done, as well as play.
You could try changing channels, 2.4 to 5 Gigs, changing locations of the router. I have had to do all of these at one time or another over the many years that I have been a Network Engineer.
Good Luck - Cheers,
M.

My iPhone 4 with iOS 6 is making me start to hate Apple. Any App and at any time I open and I can not view it or move for more than 2 minutes, they close themselves. During connections, it also gives this problem and the signal disappears after a few seco

My iPhone 4 with iOS 6 is making me start to hate Apple. Any App and at any time I open and I can not view it or move for more than 2 minutes, they close themselves. During connections, it also gives this problem and the signal disappears after a few seconds back but often the person on the other end has hung up ... I can not stand it anymore, someone suggests something?
Besides these problems, there is the battery, which was bad got worse, she is not lasting more than 10 hours, even without using the phone.
Sometimes it even seems that the problem was solved, but my joy did not last long after I celebrate all the problems return, is incredible ...
thanks.
Sorry my bad Inglês.

Try a reset hold home/sleep buttons until Apple logo appears
If that does not improve try a restore
http://support.apple.com/kb/HT4137
For your information
We are NOT Apple here we are all users helping other users
so emotion is ignored

SAPConsole and the Bell Signal

Similar Messages

Maybe you are looking for