Sata Help

hi all
i have a K8T Neo MS-6702 with an AMD 3200+ 64 processor.
also jus got a WD 250GB HDD sata
now the HD is seta2 so i set the jumper on the back on mine its pins 5 & 6
when i load up the window install i hit f6,
i tried a bunch of diffrent drivers but none seemed to work
i looked through the cd that came with the board but didnt find nothing their.
can some1 plz let me kno what im doing wrong and where i can download the correct drivers to put on the floppy.
Thx
<MikE>

FINALLY got it
well i got it yesterday
but here is what i did
1. upgraded my FLASH on the MOBO
2. reset all setting in bios, with makeing sure sata is enabled
3. Download http://66.96.84.4/support/dvr_exe/mbd_dvr/VIA_RAID_OM74.zip
4. extract all files
5. find the DskDri folder and open it.
6. copy all files inside that folder to the root of A: (providin thats yur floppy
7. Load up XP with F6 and load all XP drivers
Thx for all the help
<MikE>

Similar Messages

Sata help plz

hi all,
i'm running a 865pe meo2-pfs motherboard.i have my operating system(windows xp) connected as master on ide 1 and another hard drive for storage on slave.On ide 2 i have a dvd-rw as master and another storage drive as slave.my question is:
i wanted to add a cd-rw to computer also so i bought a mini converter sata to ultra ata to do this.now i cannot find the cd-rw in bios or in windows.I tried to configure bios by setting it as such:
on chip ata operating mode:native
ATA Configuration - PATA only
SATA Keep enabled - yes
PATA channel selection -both
This didnt help either. any suggestions would be appreciated.thx

the dvdrw also acts as a cdrw,anyway for whatever reason the additional cdrw would be better placed as a slave to the dvdrw and use the converter for the additional storage drive.

Sata Help... 875P Neo

Hello
Hope someone can help me.
Im trying to install my 3 Hard Disc, All Sata drives
i have a 875P Neo Fis2r..
i have 1 drive on Ser1 and Ser2, but im trying to install my 3 to ser3.. But bio is not detecting it.
Here is my BIOS setup:
Integrated peripherals:
USB Controller – enabled
USB Legacy – disabled
On-board Chip IDE – Legacy mode
S-ATA Only
SATA keep enabled - no
PATA keep enabled – yes
PATA channel – Both
Combined mode – SATA 1st channel
SATA ports – PO-1st/Pi- 2nd
Configure RAID – no
CSA Gigibit – auto
Onboard 1394 – enabled
Promise – as SATA
AC’97 – auto
Ser1 is my Os,
How do I get the 3rd drive without using raid..
Ser 1 - 120 Western Digital JD
Ser 2 - 200 Western Digital JD
Ser 3 - 320 Western Digital JD
Thank you

Quote from: vango44 on 16-April-06, 21:49:20
In Windows you need to install the Promise USATA drivers from the MSI CD that came with your motherboard.
Then from Windows Disk Management you need to initialize/format the disk.
I am having the same exact problem right now. MSI has a CD but with a bunch of programs, no drivers
Drivers on A disk included are G72-PRSA060
Promise 376/378 Driver and the ICH one
What are "USATA" drivers..?
Plus, my Sata drive already has sata on it. I don't want to format it, just want to attach it and get data,
Again, this is single SATA on Ser 3, not a Raid config using ser 3 and 4
thanks.

[875P Neo Series] SATA help for 875 Neo FIS2R

Hi,
I am hoping someone can help me. I am trying to install an Hitachi SATA HDD (Deskstar 7K250) to the system listed below. I tried to install the drive on SER1 but when I tried to install the installed the Intel IAA driver it said “no compatible hardware found”. I then tried to install the drive on SER3. I installed the SATA 378 driver, which asked me to restart my computer. I shut down, connected the SATA to SER3, and turned on the system. All seemed fine. I went into disk manager to initialize and format and that’s when the system restarted itself. When it restarted it said “error loading OS”. I restarted the system and opened the BIOS. Under the boot from section I noticed the C: drive that XP is on the name was “Maxtor” to something like “Maitorllll?????” I tried to repair windows to with the SATA drive still attached and the system started fine until just before the desktop would appear when the system restarted. I unplugged the SATA HDD and then had to repair windows again to get the system working.
Does anyone know what’s going on?????????
Here is my BIOS setup:
Integrated peripherals:
   USB Controller – enabled
   USB Legacy – disabled
   On-board Chip IDE – Native mode
              P-ATA Only
              SATA keep enabled - Yes
               PATA keep enabled – No
              PATA channel – Both
              Combined mode – PATA 1st channel
              SATA ports – PO-1st/Pi- 2nd
              Configure RAID – no
      CSA Gigibit – auto
      Onboard 1394 – enabled
      Promise – as SATA
      AC’97 – auto
CD151

OK, Not sure the state of everything now but this may help:
1- You don't need the IAA driver unless you enable the Intel controller "as Raid" in the Bios. It senses this and that's why it says "no compatible hardware" If the SATA ports are enabled in the Bios(your settings indicate they are) then you just need to format/initialize it like any other drive.
2- You indicate you have "PATA Keep Enabled" set to no. This should be set to yes for your IDE1 & IDE2 devices to work. The other settings on this menu look OK
3- The "Promise As SATA" should be changed to "Disabled" if you have nothing on Serial 3&4
It would help to know where the OS is installed. It sounds like it's on the IDE1 port(Maxtor).
I think you should should start by:
- temporarily disconnect the extra drive controller card
- check all the remaining drive power/data connections and reconnect the new drive to serial2
- re-enable the "PATA keep enabled" to "Yes"
- Set Promise Controller to "disabled" if nothing on it now.
- Look for a Bios setting called "Clear NVRAM" and set "yes" (It will reset to "No" after the next reboot which is what you want)
- Save Bios and reboot but re-enter Bios immediately.
- Check the "select boot order" menu and make sure the drive with the OS is before any other HDD's
- Save and reboot.
Hopefully if the OS is still intact, you'll be in it again and can use Windows drive manager to see, format and initialize the new SATA drive. Again, you only need IAA if you are using the Intel Raid controller. Also keep in mind that the SATA drive might bump all your other drive letters (from the Adaptec card) up by one so if this is a concern, just get the OS up and running then re-attach the Adaptec card and finally the new SATA drive.
Hope it works out!

K8N Neo2 MS7025 and SATA help

Hi folks, ive just changed from a P4 3.06 to an AMD 64 3500+ and the above mobo and its all gone a bit pear shaped. On my last system i used the SATA drive as master and all worked fine. Now with this one i keep getting a blue screen saying thet there might be a virus or its not connected properly. When i run an old ata drive as master and also have the SATA drive connected it bots up no problem showing the SATA drive properly.
Why wont it bot up on its own. Both drives have XP home edition?
Also all my internet router settings are on the SATA drive so i need to swap my mobo and old P4 back in to use it online
Hope you can help
Thanks
Lewis

The sata drive has a boot block in it, as on the old system i could boot with only the sata drive installed.
Is that what you mean by boot block, or is that something in the bios that needs setting?
Can you tell i have no idea

I need to upgrade my MacBook 13" white 2008 hard drive. I have found a WD6400BPVT western digital Scorpio blue 640GB (5400rpm) SATA 8MB 2.5" will this fit and work? Many thanks for any help

I need to upgrade my MacBook 13" white 2008 hard drive. I have found a WD6400BPVT western digital Scorpio blue 640GB (5400rpm) SATA 8MB 2.5" will this fit and work? Many thanks for any help

I had a 640GB HDD in my Early 2008 Macbook and it was just too much it would always freeze up the computer a bit for only a few seconds but ya. Then I realized that it was the size of the HDD that was causing it since the Early 2008 Macbook models can only handle a MAX od 500GB while the Early 2008 Macbook Pros could have a MAX of 640GB (Lucked out there!) lol But ya the Early 2008 Mocbooks can only handle a MAX HDD size of 500GB and that's it!! lol

Query help - Fetch employees working on two consecutive weekends(SAT/SUN)

Hello Gurus,
I have the following requirement and i need your help on this.
We have a table with all employees effort logged in for the days they have worked. a sample data is given below
TD_date     Emp_id     Effort     Archive_month
2-Mar-13     123     8     Mar-13
9-Mar-13     123     8     Mar-13
2-Mar-13     213     4     Mar-13
3-Mar-13     213     4     Mar-13
24-Mar-13     213     8     Mar-13
9-Mar-13     312     4     Mar-13
10-Mar-13     312     4     Mar-13
16-Mar-13     312     8     Mar-13
In the above sample data, we have employee 123 who worked on consecutive SATURDAY and 312 who worked on consecutive weekends (9th, 10th and 16th March) but the employee 213 worked on 1st weekend and 4th weekend of the month(Archive_month). So the output should return the employees who worked on two consecutive weekends as below.
Emp_id
123
312
I have written a query to fetch all employees who worked only on a SAT or SUN which is given below, but i am not able to return the employees who worked on consecutive weekends and i need your help.
select emp_id, count(*)
from timesheet_archive
where archive_month = '03/2013'
and trim(to_char(td_date,'DAY')) in ('SATURDAY','SUNDAY')
group by emp_id having count(*) > 1
order by td_date desc
Please help me with an approach in SQL or PL/SQL to generate a report of employees who worked on two consecutive weekends.
Thanks,
Edited by: 999145 on Apr 9, 2013 11:08 PM
Edited by: 999145 on Apr 9, 2013 11:10 PM

hi Manik,
thanks for your response!!
Please find the below create and insert scripts for your testing.
I am also validating the output with my requirement. Thanks for your help!
create table timesheet_archive as
(TD_date date,
Emp_id number(19,0),
Effort Float,
Archive_month varchar2);
insert into timesheet_archive values (to_date('2-MAR-2013','dd-MON-yyyy'), 123,8,'03/2013');
insert into timesheet_archive values (to_date('9-MAR-2013','dd-MON-yyyy'), 123,8,'03/2013');
insert into timesheet_archive values (to_date('2-MAR-2013','dd-MON-yyyy'), 213,4,'03/2013');
insert into timesheet_archive values (to_date('3-MAR-2013','dd-MON-yyyy'), 213,4,'03/2013');
insert into timesheet_archive values (to_date('24-MAR-2013','dd-MON-yyyy'), 213,8,'03/2013');
insert into timesheet_archive values (to_date('9-MAR-2013','dd-MON-yyyy'), 321,4,'03/2013');
insert into timesheet_archive values (to_date('10-MAR-2013','dd-MON-yyyy'), 321,4,'03/2013');
insert into timesheet_archive values (to_date('16-MAR-2013','dd-MON-yyyy'), 321,8,'03/2013');
insert into timesheet_archive values (to_date('2-MAR-2013','dd-MON-yyyy'), 124,8,'03/2013');
insert into timesheet_archive values (to_date('9-MAR-2013','dd-MON-yyyy'), 124,8,'03/2013');
insert into timesheet_archive values (to_date('16-MAR-2013','dd-MON-yyyy'), 124,4,'03/2013');
insert into timesheet_archive values (to_date('23-MAR-2013','dd-MON-yyyy'), 124,4,'03/2013');
insert into timesheet_archive values (to_date('16-MAR-2013','dd-MON-yyyy'), 241,8,'03/2013');
insert into timesheet_archive values (to_date('23-MAR-2013','dd-MON-yyyy'), 241,4,'03/2013');
insert into timesheet_archive values (to_date('24-MAR-2013','dd-MON-yyyy'), 241,4,'03/2013');
insert into timesheet_archive values (to_date('2-MAR-2013','dd-MON-yyyy'), 412,8,'03/2013');
insert into timesheet_archive values (to_date('3-MAR-2013','dd-MON-yyyy'), 412,8,'03/2013');
insert into timesheet_archive values (to_date('30-MAR-2013','dd-MON-yyyy'), 412,8,'03/2013');
insert into timesheet_archive values (to_date('31-MAR-2013','dd-MON-yyyy'), 412,8,'03/2013');

Need help in installing a SATA hard drive with 865pe NEO2

Hello there
I need a help in installing a Sata hard drive ,it is WD 250 GB , my motherboard is 865PE Noe2 , the bios is the latest one
already I got another old hard drive ,not a Sata ,a regular IDE one installed as a master hard drive
I want to install the sata hd as a slave for the IDE hd for now to transfer the files and documents
I already physically installed the Sata hard drive yet the problem is that it was listed in the bios , I followed some of the steps here in the forum mentioned but all what I got is I found it listed as the fourth IDE master , not as the primary IDE slave
in Windows Xp Sp2 it is not listed of course in the windows explorer , but it is there in the device manager
look I am very confused and I tried most of the combinations in the ide configuration in BIOS
what should I do coz I am feeling so bad and stupid ,you can consider me a n00b in this hard drive thing

1st the sata drive cannot be listed as a slave drive to the ide master [key word=ide-can be configured as master OR slave, master IF only 1 hd, master and slave IF 2 hds], on the sata controler you can have master and slave, the ide cable has two connectors for the hds, sata has only 1 hd connector.
are you wanting to install the sata as primary master and move the operating sys to that drive, if so you will need an IMAGING software to move an operating system OR you could do a fresh operating system install to the sata drive then install your programs.

Been sat here for the past 5 hours trying to figure out why itunes wont download, it says error and something to do with Microsoft? Help me please.. getting a bit bored?

been sat here for the past 5 hours trying to figure out why itunes wont download, it says error and something to do with Microsoft version? Help me please.. getting a bit bored?

i have this problem too
my dad thinks its because itunes is getting overloaded

My cat sat on the keyboard during update now the system is pale with apple in center and under that circling lines i cant either reboot or shut down.. Powering off only resumes the same. HELP

My Cat sat on the keyboard during regular updating of the system. First it went to hypo-slow with alot of beach ball action while i tried to power down for a restart and individually force quit most open apps. Restarted/Resumed same issue.. changed to( close open apps upon restart.).... Now it is light grey, apple icon in center nothing else but the rounding cursur under the middle/only apple icon..... just goes round and round...does not respond to any shutdowns other than power off..... Makes the regular start up noise and back to same routine.... PLease help if possible....
Thanks Tina Schlemer

Try booting to the recovery partition and running Disk Utility.
1, Boot while holding down the command and R keys (two keys).
see this page: http://www.apple.com/osx/recovery/
2. Run Disk Utility, select the hard drive in the left column, First Aid then click Repair Disk.
3. Quit DU and restart.
If that does not do it, you can reinstall the OS from the same screen as took you to DU.
(My cat has never been able to do what yours did. I think he is just trying to email his friends.)

Help - how can I convert G5's SATA power to 4-pin for an Ultra SCSI?

I am trying to put an Ultra SCSI hard drive in an G5. For *some reason* this is very, very hard to do. I have bought a compatible ATTO PCI card that is working fine in the slot. I can connect the data cable from the SCSI card to the drive installed in the G5 (although it was hard snaking it through). The problem is power. What I need is an adapter that will convert the end of the SATA power connector into a 4 pin female for the drive side. This product (http://eshop.macsales.com/item/Micro%20Accessories/SATAPA/
) looks right, but seems to be the wrong sex -- the 4 pin part is certainly the wrong sex (since the drive is male, the adapter must be female), and I can't tell if the SATA part will fit (looks like it's also the wrong sex). The picture of what I am trying to do is here:
http://flickr.com/photos/ppayne/159005320/
Can you please help me here? I can't believe that people using a special (high performance in my case) drive with a g5 is something no one has ever tried to do. I know SATA is the future but I want to use my special hard drive (15,000 rpm Ultra SCSI) with my server.
So once again, I am looking for an adapter that will be male SATA power on one end, and female 4 pin on the other end. If anyone could help that would be great.

Like Timotheus D said, don't over think it, get a y-splitter to go off the power for your super drive, like: http://www.directron.com/cbl-y.html

Help! Can't get IDE 3 - SATA to work.....

Hi all,
after going to some of the threads regarding SATA/PATA IDE controller and setup, I am even more confused.
I built my first system back in January and had some issues with my video card (ATI AIW 9800 Pro), which are now finally resolved (after 2 RMA’s).
Last night I upgraded the BIOS successfully to v 1.4.
Here is my problem: I hooked up a mobile 250 Gig WD HD to IDE 3 (strictly for data back-up)– which is not recognized. When I first installed XP and hit F6 nothing happened – I had the “VIA SATA RAID driver” diskette in the A: drive – but the installation process just went on….
Now I finally (with help from ATI customer support) got my video card installation issues resolved and I don’t want to do a re-install of XP.
Is there any way to install the necessary drivers without re-installing the OS?
(if yes – can I use my diskette/disc – or go to MSI’s website for a “live update”?)
What would be the correct BIOS setting?
Remember – I do not need Raid – just IDE 3 hook-up for a removable HD.
Thank you for your help,
hansmann

What am I doing wrong???
I am getting the message “No drive attached to FasTrack controller” in BIOS – which indicates to me that the drive is not seen or not connected. So I checked the settings – no jumpers, replaced the conductor cable and made sure the power connector was attached.
Same message…
This is on my IDE 3 single, removable 250 GB WD HD – trying to set up as Promise
RAID for data back up.
Under “Disk Mgmt” only the 2 HD’s on IDE 1 show up – the same under “Disk drives”.
Under SCSI and Raid controller both, the VIA serial ATA Raid and the Win XP Promise
FasTrack 376/378 ™ controllers are showing.
When I am hitting control F in BIOS – nothing happens (at the Promise utility screen).
Also, I have XP pro installed – so all of this is on an existing OS, not a new install.
What do I miss??? This is driving me crazy.
As usual – your help is appreciated.
hansmann

SATA Raid 0 and Overclocking Issues. Help!

I'm building out a machine that doesn't seem to want to overclock in the slightest bit. I think my Serial ATA RAID 0 array seems to be the problem with OC'ing. Each time I change the CPU FSB settings, when I boot up, it tries to detect my array. Then it reboots after it fails.
Does anyone know what's going on? Someone mentioned PCI Bus settings to me...???
On Anandtech they OC'd this chip to 2.6 Ghz (290x9) with an 8.3%+ in voltage. I can't even get to 220.
Any help would be much appreciated.
Thanks!
======================
System Setup:
Athlon 64 3000+ Socket 939
K8N Neo2 Platinum
2 Hitatchi 80 gig SATA HD's
Leadtek Winfast 6600 GT (AGP)
Zalman CNPS7000B-AlCu Heatsink
Seasonic Super Tornado 400W PS

Ok, I switched it to SATA 3/4 and then I couldn't boot. I kept getting some error which would cause it to boot again. It happened right after it detected the array successfully. The warning message happened so fast the first couple times I didn't even notice it. It would flash some sort of blue screen like error (only it was a black screen) and then reboot itself.
Frustrated, I decided to start from scratch again. I wiped out the discs and re-created the RAID 0 Array and put my WinXP CD back in. Now while setting up WinXP I hang at the "Setup is starting Windows" screen.
It won't go anywhere from that. It happens after I copy over the RAID Driver and Controller from the Floppy. It copies more files after that and then hangs...
I also reset the CMOS with the jumper settings, un-did and re-did my SATA connections, even unplugged the little MB battery... :(
Any suggestions? This is so frustrating.
TIA.

[865PE/G Neo2 Series] Just got my first SATA drive.. need help booting up.. :(

Hey guys
I just got my very first SATA drive. it's a Hitachi 160GB 7k250!
anyway, I wanted to set this new drive (partion 1 to be exact) as my PRIMARY or what I like to call SYSTEM drive.. this is where i store only my windows core files and program files..
My previous setup is that I have 2 PATA drives (Primary master and Secondary Master) and 2 DVD drives (Primary Slave and Secondary Slave)..
Now with the introduction of this new SATA drive, well, i didnt know what to do..
I got as far as setting my BIOS to: (forgive me if the following isnt exact terms as in the bios)
ATA = PATA Channel only
keep SATA = YES
(and some settings i can't remember)
I was able to boot my computer up with the SATA HD partitions set at the next available drive letters.
Now here's the problem.. I currently have an Image of my C: (system) created with Acronis TrueImage 8, and i restored that to my SATA drive's FIRST partition...
The first partition is also formatted with the same file system NTFS and is set to primary..
From here, i honestly dont know what to do..
ofcourse I will have to set bios to boot the SATA drive first...
Also, since the System image (windows XP) is that of DRIVE C: I have to somehow set the SATA drive to be HD0 (first channel)... playing around in my bios I have accomplised to have set my SATA drive as IDE channel 1 = Primary.. funny thing is the rest of the drives moved down starting at IDE Channel 3 and 4..
Still i went on to boot up.. but i was unsuccessfull. I get a very quick blue screen (about 50 miliseconds) and then my computer shuts off and reboots..
I played around witht he settings and tried many things.. still get the quick BSOD and then reboot problem
GUys? What am i missing here?
I didnt know this SATA drive was gona get complicated.. i thought i'd be up and running by now.. :( ..
Please lend me some of your knowledge peoplez.. :D
tea

Hi Danny,
Thanks for your reply.
I have followed your instructions to the dot.. now im getting as far as the WindowsXP Boot Screen... after an unusually long loading time, i get that BSOD flash which i really cant make out since the darn thing reboots right away.. :(
I also tried
Native Mode
ATA Configuration - SATA only
(changing this to SATA, thinking you were mistaken since am booting sata up.. but what do i know ei?)
SATA Keep enabled - yes
PATA Keep enabled - yes
PATA channel selection - both
same results... a long boot screen loading time.. then a quick BSOD..
I alsto tried booting up in safemode.. the loading stops at agp440.sys and reboots after a long pause at that part.
So now I switched back to your recommended settings, but this time setting my old hard drive to boot (PATA).
To my surprise im back to where i started (despite maintaining your suggested settings) thus i am replying to this post again..
also, i noticed that with your suggested settings, my SATA drive is on IDE channel 1.. and the rest on IDE channel 3 and 4.. but here in windows my old hard drive is still drive C:.. I was expecting my SATA drive to be Drive C this time.. could this be the problem here?
I mean the windows Image I restored is setup to work on drive C (first drive), although I removed all the drive, could it be that my SATA drive is still not on drive C?
Please help. My brain's bleeding
Tea

Plz Help Meeeeeeeeeee!!!!!!! Sata Disappear

Ok i have 2 SATA SEAGATE BARRACUDA 8MB 120 GIGAS
one was on array 1 and the other one on array 2 c: and d: respectively
suddenly the 2nd one disappear it HAS ALL MY INFORMATION AND FILES !!!!!!!!!!
EXTREMELY URGENT PLZ HELP MEEEEEEEEEEEE!!!! how can i make it come back
i HAVE A MSI K7N2 ILSR MOBO and when i enter the SATA MENU (ctrl + f)
it appears the fist HARDDRIVE AS ARRAY 1 and the other one appears as
ARRAY FREE
it gives me the option of define array, delete array and rebuild array
WHAT CAN I DO !!!!!!!!!!!! SOME ONE KNOWs?????????????????????????????????????????

Define a new array - stripe mode and DON'T quick initialize the drive, only create array.

Sata Help

Similar Messages

Maybe you are looking for