Satellite P10-504 doesn't boot after RAM upgrade

Just got 2x 1GB sticks of DDR 400 soddim's, and no boot.
Now after reading up on what I could find on similar models, seems that these older laptops may not handle that fast of ram?
Would using some DDR 266 be more appropriate?

Hi
If the notebook doesnt boot up then there is a big chance that the RAM is either nto compatible or its faulty.
I think its not compatible.
I found this page:
http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=7090&ft=m&st=3
According to this page the P10 supports the *200-Pin PC2700 (333Mhz) DDR SODIMM* memory modules!
So your RAMs are not compatible!

Similar Messages

Satellite A110-260 doesn't run after RAM upgrade

A110-260 - 512 MB Ram - 533 MHZ - 100GB - BIOS V1.20 (2 years old)
Hello,
my first attempt to upgrade my RAM failed.
After correct installation of 2 Kingston 1GB Ram (Typ: RMN 2-.800/1GB SO-Dimm DDR 2), my notebook didn't start again, only 5 short sounds (in owners manual: not the right extended memory).
Curios: 1 Kingston 1 GB-Ram mixed with original Toshiba 512 MB-Ram, the notebook boots, but reaches only 896 MB extended memory. Performance not signifikant better.
Who can help me ?
Andi11

Is that Kingston memory 800MHz? That laptop is designed for 533MHz Memory (PC4200). Usually the 800MHz Memory will bump down to 533MHz (probably using the SPD table), but there may be a compatibility problem.
So ultimately you should buy 533MHz DDR2 Memory with similar CAS/RAS Timing as the original Toshiba Memory.
Perhaps the second RAM slot is faulty? If you run CPU-Z, can it detect the second module correctly?
Note that the Graphics card may use some System Memory as Video Memory, so it sounds like the laptop sees the 1GB Module but reserved 96MB for the graphics.

MacBook not booting after RAM upgrade

I'm sorry if the case has been already posted.
Yesterday I took my MacBook Alu unibody late 2008 to a RAM upgrade (from 2 to 4gigs) to an offical Mac Reseller. They installed it and showed me that the system loads properly and recognized the new RAM.
I took it home, started working on After Effects and Photoshop and when i wanted to check a video on Quicktime, this program refused to boot.
Then photoshop freeze and after effects did so. I quited all aplications and restarted. On restart after the 'bong' i've got the grey screen white an apple logo and a loading bar underneath, that was it, it never finished loading but shutting down.
After the 2nd try the computer gave me the BAD RAM alarm signal right before the start button was pressed and nothing more. I just managed to start it ONCE on safe mode, but this one also freezed and colapsed.
Today i didn't get the BAD ram alarm but the grey screen and loading bar after shutting down.
I took it back to the reseler, the shop boss who did the upgrade wasn't there , the guys on the morning shift placed the old RAM back resulting the same. So they told me it's a software problem, not hardware and might be caused by a failed firmware update or something i did wrong and since i was showed that the system booted after the upgrade i can't complain or argue that they did somethiing wrong.
So basically the want 80euros to check what's wrong with my computer plus the 120 i already payed them for a RAM that doesn't work and of course the repair cost of the computer.
On monday i'll go to talk to the boss, what do you guys recomend me to tell him? i'm frustrated that the guys there treat me like if i broke my computer for beeing stupid and wanted to get it fixed for free, when it clearly broke after they did something wrong on it!
please advice me!
thanks!
Message was edited by: finn bell

What brand is the RAM? From what you said, it is obvious that the RAM is at fault. I would simply tell them that it is not compatible and return the RAM.
Check the System Profiler to see what it says about the RAM (Apple Logo - About this Mac - More Info) and run this application to test the RAM:
http://www.memtestosx.org/joomla/index.php
If either shows any errors, print out the results and take them with you to the store.

Mac mini won't boot after RAM upgrade.

Tried installing new RAM in my Mac Mini, 512MB stock to 2GB of Crucial. Followed the directions to a T, grounded myself the whole time.
Things I've tried so far:
1. Resetting the PRAM, no luck.
2. Holding option at start-up, shows no icon.
3. Holding shift, no luck.
4. Holding X, nothing.
How do I get it to accept a CD if it won't boot?

Welcome to Apple Discussions!
You clearly have a problem, but you don't describe exactly what that is other than that your mini won't boot after the upgrade. What happens when it starts up? Does it attempt to start and hang up on the grey or blue screens, or does it start beeping at you almost immediately after you try and start it up, and also flash the power light?
If the former, then you may have dislodged a connector while working inside the system, in which case opening it up and checking that everything is firmly connected would be the first thing to do. If the latter, then the beeping/light flashing is the system telling you it has failed the power-on self test and the pattern of beeps/lights indicates why. In your case likely the system can't find workable memory. In that instance, opening the system and ensuring that the RAM is firmly and fully seated would be a good step, and if the mini continues to fail, then replacing the new RAM with the original to test that the system will then start.
It is not likely that anything had damaged your MacOS install in the process of upgrading, thus normally no reason to need to boot to CD as a result of a RAM issue.

Satellite M200 doesn't boot after RAM 4GB upgrade

Hi,
I recently upgraded my RAM just to speed things up a little as RAM is soo cheap these days.
I have a M200 T2130 Vista came with 1GB (2*512) sticks.
The new sticks are 2 *2GB Dane-elec DDR2 pc2-5300, when I put the two in and rebooted the hard drive light came on briefly and then it just stayed idol, no POST, Bios options.
I tried using a single 512 stick with both new sticks and they both work in a 2.5GB setup just not together also this only works when the 512 stick is in the more internal slot and not the other way around.
So if anyone has had a similar prob or can give me some advice that would be great, I'm not to sure if the motherboard can support 4GB?
Thanks, Dave.

Hi
There are two possibilities why your M200 doesnt boot after the RAM upgrade.
Firstly the installed RAM could be not compatible or could be faulty or the notebook doesnt support the 4GB RAM.
I dont know what M200 do you have exactly but you could check the installed chipset and could check on the Intel page if this chipset would support the 4GB RAM.
Greets

Re: Satellite A660 - No boot after RAM upgrade

I have just gotten 8GB of RAM for my Satellite A660, it is Corsair CM3X4GSD1066 4GB PC-8500 (1066MHz) 204-pin SO-DIMM DDR3 RAM CL7.
The system posts fine and the 8GB is showing up in BIOS but once its clears post and goes to load Windows it stops on the black screen, the cursor flashes a few times then it stops. I have left it for about 5 minutes and it wont boot through.
Please Help.
I have replaced the 4GB sticks and it works fine.

Hello
For me it sounds like that the modules are not compatible or have defective sectors
As Akuma wrote, such performance modules are risky in notebook because you dont have any options to change the latency values as on desktop computers. So I always prefer Kingston modules for notebook RAM upgrade.
But before you buy other modules, try a BIOS update and load the default settings.

Macbook Pro is Not Booting After RAM Upgrade

Hi,
I just upgraded the RAM in my MacBook Pro running Mountain Lion from 4gb to 8gb (Using the memory that the guy at Fry's recommended). It has been stuck on the Apple logo for about 20 minutes after the upgrade, even after I made sure that the RAM was seated properly. Is it normal for it to take this long to boot after a RAM upgrade?

I installed 8gb (2 X4gb) and it has a maximum of 8gb. I have determined that it was just bad RAM, so I will return it as soon as I can.
Thanks.

IMac won't boot after ram upgrade

For some reason, my iMac late 2013 3.4Ghz quad core i5 won't boot with new ram modules added. New ram is exact same specs as original that came with the iMac. I've tested the new ones on their own in the iMac, and the system boots up fine. Same goes with just using the original ram. But when I put all 4 together, the iMac doesn't boot up. Not even the chime.
Combinations I've tried are:
1-Old
2-New
3-Old
4-New
No boot
1-New
2-Old
3-New
4-Old
No boot
1-New
2-Old
3-New
4-empty
No boot
1-Old
2-New
3-Old
4-empty
No boot
1-New
2-Old
3-Old
4-New
No boot
1-Old
2-New
3-New
4-Old
No boot
The only combinations that work are:
1-New
2-empty
3-New
4-empty
Boot good
1-Old
2-empty
3-Old
4-empty
Boot good
I just got off the phone with Apple, and they are saying all modules have to be the same size. ie. all 4GB or all 8GB. Can't mix and match sizes. Which is strange, because I've never heard of this. My Mac Pro has different speed ram modules, with different sizes in it. As long as I install ram in pairs, it runs like a charm. I've even heard the new iMacs don't have to have ram installed in pairs.
I'm wondering if slot 2 and 4 are maybe damaged? I haven't tried using just slot 2 and 4. To my understanding, you have to use 1 and 3 first. Can anyone confirm this?
Also, I've read a couple of people had to wait 30 seconds for the chime when they installed new ram in their iMacs. I didn't wait 30 sec to see if it would boot. Never heard of any Mac taking 30 sec to just chime in. lol Has anyone else experienced this? Is there a fix? Tx.

CLICKY CLICK---> iMac: How to remove or install memory
Or
Apple>About This Mac>More Info>Memory: Double click "Memory Install Instructions" at the bottom right of window.
my iMac late 2013 3.4Ghz quad core i5
Conflicting info. Your system profile shows: Mac Pro, Mac OS X (10.6.8). Please update/correct.

HP g4-1387 won't boot after RAM upgrade

I have an HP g4-1387la with 4Gb of RAM and I want to add it 4 more Gigas.
I bought a 4Gb DDR3 SODIMM 1333MHz Kingston RAM but when I put it in the slot and try to boot my notebook it stays on a blackscreen, it turns on, but doesn't boot.
If I take off the Kingston RAM it boot normally. This notebook accepts up to 8Gb of RAM. What is the problem ?
Thank you

Are you running Windows 7 - 64bit?
HP Pavilion G4 Notebook PC Maintenance and Service Guide
From the Service and Maintenance Guide:
Supports the following configurations:
● 8192-MB total system memory (4096×2; not
supported with Windows® 7 32-bit
operating system)
● 6144-MB total system memory (4096×1 +
2048×1)
● 4096-MB total system memory (4096×1 or
2048×2)
● 3072-MB total system memory (2048×1 +
1024×1)
● 2048-MB total system memory (2048×1 or
1024×2)
● 1024-MB total system memory (1024×1; not
supported with Windows 7 64- or 32-bit
operating system)
Here is a reference Guide you can look over to see if you missed anything.
There is a Troubleshooting section you can check that may help resolve any temporary issues.
Upgrading Memory (RAM)
Kind Regards,
Dragon-Fur

Macbook pro doesn't boot after iOS upgrade

Hi all,
I've upgraded my macbook pro (was requested automatically the upgrade) and after reboot to finish the installation, my macbook doesn't boot up.
Is there any way to boot it up? A kind of boot in safe mode?
I'm trying to power it up but nothing. It doesn't boot at all.
Please, can you help me with this.
Thanks
Álvaro

iOS is for iPhone, iPad not for Mac. So what upgrade are you referring to?

MacBook Pro won't boot after ram upgrade...

Hey everybody! Hope everyone is having a great Christmas! I got a 16gb ram upgrade for my 2012 MacBook Pro 15 today and I am having some trouble with the upgrade. Its an odd problem. I installed the two 8gb sticks no problem, but when I try and boot into OS X the machine shows the apple logo with the spinning wheel underneath, and then it just shuts itself off. I don't know what the problem is. The machine boots fine into my Windows 7 partition, and registers both sticks of ram. OS X restore also boots no problem and lets me reinstall OS X, which is what I am doing currently. IDK if this is just because of a hardare change or what. The ram I installed is Adata pc3 12800 1600mhz ram, so it should be supported.

Replace the Ram, buy from OWC or Crucial, buy the Ram Apple recommend, don't rely on "it should work"

Ix2-dl doesn't boot after firmware upgrade

I upgraded to the latest firmware and it won't reboot now. the power light just keeps blinking.

Hello lcgrzy,
I recommend trying the following steps:
--Power off unit, remove power cable and re-seat all disks. Then reconnect the power adapter to attempt to boot up.
--While powered off, swapped the disks to opposite bays. Then see if the unit fully boots after about 5 minutes.
--Try booting the unit one disk at a time to see if either disk will fully boot.
--Try booting the unit one disk at a time to see if the firmware on the unit seems to be ok.
--If the unit does not seem to boot after the above, please call lenovoEMC support.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Re: Satellite A200-1AX doesn't boot after BIOS update

Hello all!
I wanted to install XP on a Satellite A200-1AX.
So I tried to update the Bios to the version that supports XP.
When I tried to install it, Vista crashed and now the laptop won't even turn on.
When I keep the power button pressed, the fan wheezes but nothing else happens.
I think the BIOS is gone or corrupted.
What do I do?
Thanks in advance for any help!

> When I keep the power button pressed, the fan wheezes but nothing else happens. I think the BIOS is gone or corrupted. What do I do?
What to say buddy. Looks like something went wrong during the BIOS update procedure Possibly the BIOS was not written correctly and the ROM module must be flashed again using a special procedure and tool.
In such case you can do nothing you have to contact the ASP in your country for a fix!!!
Dont waste a time and ask an authorized service technician for a help.
Good luck and best regards

Lion freeze on boot after ram upgrade.

I have a mid-2010 13" Macbook Pro. I wanted to upgrade to 8G of ram so I bought this: http://www.amazon.com/gp/product/B002YUF8ZG/ref=oh_details_o00_s00_i00
When it arrived in the mail I installed it and booted the laptop. The apple logo comes up, the spinner starts spinning and then after awhile freezes. I figured that I recieved bad RAM so I sent it back to apple and they sent me new memory. I installed the new ram and the same thing happened again. Booting in verbose mode (Apple-V) doesn't give anything useful.
This time I decided to run memory tests. I booted into single user mode (which sees 8G of memory and works fine) and ran memtest overnight. It ran 6 or 7 passes without finding any memory errors.
My next plan is to try to my DVD reinstall/repair the OS to see if that will help but I don't want to do that because I would have to downgrade to Snow Lepoard and then reinstall Lion and that takes long enough to try to avoid.
Any things to try?

When you boot in single user or safe mode, all third party software is prevented from started. So it is possbile one of your third party party applications that are starting at boot is not compatable with the new RAM. I would try turning it all off and then test them all each in turn.
Allan

Satellite A200 PSAEOE won't boot after memory upgrade

Hi, I am first time here.
I have bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB ram memory. I bought a pair of Corsair ram (2*2GB VS2GSDS667D2). After I installed the memory the computer won't boot. I have intel 945 chipset, which is capable of 4 gb (manual page1-2). The bios version is 1.8 from 2007.
Can anyone help me, please.
Message was edited by: ovidiu marian

Hi
The A200 series supports different chipsets;
Intel 945PM
Intel 945GM
Intel 943GML
As far as I know your notebook supports the *Intel 943GML* chipset and this chipset supports max 2GB RAM.
Take a look in your notebooks user manual *Page 18.*
Summery: 4GB RAM are not possible and therefore your notebook does not boot up.

Satellite P10-504 doesn't boot after RAM upgrade

Similar Messages

Maybe you are looking for