Satellite Pro P10 will not remain on mains power

My Satellite Pro P10 regularly switches to battery power even though the mains power is still connected and the LED on the front of the pc indicates it is connected. I then have to let the battery run down and reboot before it recognises th epresence of th emains power again How Annoying is that !!
ANy ideas what the problem might be ? Don't think about physical connection probelms - the LED shows the mains is still there !!

Hi
In my opinion the answer can give you only technician after checking your notebook. For me it looks like some problem with power supply electronic. Sorry but I believe you will not be able to do anything alone.
If you use your notebook on the desk, remove the battery and use it with AC adapter only. My brother does the same since the battery is defective. Try also to start notebook on AC power supply and put the battery after 5 minutes. It will be interesting to know it the battery is recognized and charged properly.

Similar Messages

Satellite Pro 4340DVD will not boot up - pci.sys missing or corrupt

I bought a Toshiba Laptop Satellite Pro 4340DVD Model # PS434C-3N152, Serial # Y0018185J, off E-Bay.
The original operating system, Win 98SE has been upgraded to Win XP Pro. No disks came with the laptop.
The laptop crashed yesterday while I was online and will not boot-up.
_Error message reads:_
+The following file is missing or corrupt: System32\DRIVERS\pci.sys.+
Any suggestions on how to rectify this problem will be deeply appreciated. I would very much like to have a users manual for this unit but haven't been able to find one.
Thanks!
Sam

Turns out that the dirty dawg was Anti-Virus 2009 that caused the problem. Managed to get laptop to boot up in "safe mode," found the dirty dawg, deleted it, and the laptop booted right back up.
This issue is resolved!
Sam

Satellite Pro M10 will not boot again and comes up with the error message

My Toshiba Satellite Pro M10 notebook will not boot again and comes up with the error message "load error" when I push the power button.
The problem arised after installation of "symantec system works" and trying to restart windows XP professional to make the installed program executable.
What can I do to get the notbook restart again?

Hi everyone
If you cannot acces to the boot menu by pressing F8 you can try to recover the the master boot record from Windows Xp professional installation Cd, to do this:
Attention: don't run these commands if you have more than one operating systems running in your laptop.
Boot from Windows Xp installation cd
Choose repair installation from console by pressing "C" key.
A console will open asking you for administrator password, insert the password and press enter.
Run de command: FIXMBR (It will write a new boot record)
Run de command: FIXBOOT (It will write a new boot file)
Restart the laptop and now windows should start without problems.
Regards

Satellite Pro 480CDT will not boot with HDD fitted?

Hi
I have tried several hard drives in my Satellite Pro 480CDT but none of them will boot. The screen stays black and the power led flashes orange (long, short, short, short, short, long, short, short). If I take the drive out the machine goes to the 'In Touch With Tomorrow, TOSHIBA' screen. It will see Windows CDROM or a floppy. I have tried with 6 HDDs all below 6Gb and as far as I know working. I have tried with another 480CDT a 220CS and a 2140CDS. Surely all HDDs and laptops have the same fault? Do I need to update BIOS or something as none of the drives are original to the machines.
Please help!
Thanks
John.

Hi John
I am afraid there is nothing you can do alone. When power supply electronic detects some power problem it sends hexadecimal code. In this case you must contact technicians. They can read this code and will know what is wrong there.
Just for info: I have found out that original HDD for this unit has part number P000244000. Maybe it will help you to obtain some other HDD for tests.
Sorry I can not tell you more about this oldie.

Satellite Pro L300 will not boot after Bios update

Help please.
I have just formated a Satellite Pro L300 laptop.
I used all the updated drivers from Toshiba and all went very well.
I then updated the bios with the latest version.
After doing this the laptop will not boot but just keeps scrolling through the start menu and no matter what option I choose it just keeps doing the same thing.
Any ides welcome

Hi
I used the Microsoft installation disk but just keep getting to the same stage until the blue screen appears. I have tried different installation disks and also changed the hard drives as well. I can do everything in bios, change boot device enable or disable devices but that is it. I have tried a few times to instal windows but it just stops at the same point saying windows is stopping instal to protect the system. I fear the bios update has done some permanent damage as I cant get past the dreaded blue screen.Thanks anyway

Satellite Pro 6000 will not boot or do anything

Hello,
my satellite pro 6000 stopped working all of a sudden.
Power led, battery, keyboard leds are on, but nothing happens, tried to remove battery,cd, hd and put them back, nothing seems wrong.
Also tried the backspace trick in case but did not do any good.
It just does not start at all.
Any ideas out there ?
Thanks
[Edited by: Forum Moderation]

Hi,
unfortunately all the leds are working fine, no blinking that could point out a problem.
I am afraid that the motherboard might be cooked, I have seen similar symptoms on the net, it seems like a know issue at toshiba.
FP

Satellite Pro A120 will not boot up

Sorry for bad English!
My computer will not boot.
I want to install a BIOS but connecting it to another computer but I dont know how?

In my opinion its not a faulty BIOS but I think the virus on your notebook caused this issue.
The error message says everything:
+Malicious program will access to the read memory+
+problems on bios+
If you are not able to boot up the notebook, neither from the Recovery CD, bootable CD (XP, Linux) nor from HDD then its a serious issue and you should definitely contact the ASP in your country.
If you are a lucky man then the ASP technician would be able to flash the BIOS ROM using a special procedure and the notebook should function again.
Bye

New Satellite Pro L300 will not start up or operate

My new laptop will not start operating. I have done everything by the book in regard to installation, but once it asks for my user name and password, it goes to a page where it says "Preparing your system". Then after about 10 mins it goes back to the sign in page with my user name and password, and repeats the whole thing.
How do I fix this? The laptop was bought new from ebay as a gift.

Getting a DOA is so random that it probably won't matter when you place your order. Right out of the box,the machine should start up instantly when you press the power button. Yours doesn't.
It sounds like it arrived with a dead battery and the power adaptor is not charging the battery. Even so, it should start up from the power adaptor alone. It could be that the power adaptor is not being recognized.
If you still have it, you could try resetting the SMC, which could possibly get things working again:
http://support.apple.com/kb/HT1411?viewlocale=en_US
Your satisfaction is important to Apple. If your machine has problems out of the box, they would rather give you a replacement immediately than to mess around with one which obviously has a problem of some sort. The one you return will go to the repair depot and the problem will be found and repaired if possible. Then it goes to the online store and is sold as a refurbished machine.
A power issue like yours may be simple to fix, or it may not be. The last thing you want to do with an expensive brand new machine is to find out it is defective in some way and have to send it off for repair. You would much rather just give back the defective machine and get another one that is not defective, and I think Apple realizes this.
There's really no reason to wait before submitting a new order--you can do it at your convenience.
Good luck!

Satellite Pro L20 will not turn on

Hi,
I was using my laptop yesterday when my baby son pulled out the ac adaptor cord from the back of the laptop, when i went back to it, it had turned itself off, i have tried to turn it on with no sucess, i have no lights nothing.
not even the light to show the laptop is on charge is working.
its like its completly dead (i hope not)
Any ideas??
Regards,
qube

I would take the battery out so there is no power going into there at all, then hold down the power button for 10secs to clear the capacitors then reattach the battery and try again.
If not I would take out the battery again and plug in the mains and try turning it on without the battery in.
James.

My ipad will not charge from mains power

my ipad doesnt charge even when connected to mains with the cble and usb charger provided it just shows a not charging symbole next to the battery level and sometimes pops up with a message stateing that i can not charge with this accseriore i need help urgently

Do you have access to another charger and cable? You could have a bad charger, bad cable or problem with the cable to iPad connection. First test would be a different charger and cable to see if that resolves the problem.
If not, you need to visit an Apple genius bar and have the techs check the system to see where the fault is.

HT3964 I have a MacBook Pro that will not boot up. The apple symbol Read more: I have a MacBook Pro that will not boot up. The apple symbol is there and a spinning wheel continues to spin. Any options??

I have a MacBook Pro that will not boot up. The apple symbol is there and the spinning wheel keeps spinning. Any idea how I can fix this?

Reinstall OS X.
Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
OR
Reinstall Snow Leopard without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

I am using a Canon 640 printer and my MPNavigator will not remain open. It pops open then quickly closes. I've used it for several years but it just started doing this. What can I do to fix this problem?

I am using a Canon 640 printer and my MPNavigator will not remain open. It pops open then quickly closes. I've used it for several years but it just started doing this. What can I do to fix this problem?

I had a similar problem with a Canon MP800R under Mac OS X 10.9.2 Mavericks.
In my case, the MP Navigator app in the dock was linking to the wrong file.
It linked to Applications > MP Navigator 2.1.app > Contents > Resources > MP Navigator.app, but it should link to the "main" app, probably under Applications > MP Navigator 2.1.app.
After pulling the correct MP Navigator app file to the dock, I can start MP Navigator again by clicking on it in the dock. However, when clicking on it, a second MP Navigator icon will show up in the dock and stay there until the app is closed. By the way, the MP800R scanner also works (although officially not supported by Canon).

After recent update to my macbook pro itunes will not open, it just bounces when I click on it

fter recent update to my macbook pro itunes will not open, it just bounces when I click on it

Means they are going to mess up your iPhoto Library pictures database so it's unreadable by older versions of iPhoto on older OS X operating systems.
You have the choice to right click on the iPhoto Lbrary and inside is a folder called Origianls, use the Finder to Duplicate this folder, then move the OriginalsCopy out of the iPhoto Library folder and save it elsewhere.
I dont' think Apple will every intentionally touch the originals, however it's possible they could.

My MacBook Pro persistently will not connect to my wireless router. The message "connection timeout" appears. What is a connection timeout and how can I fix?

My MacBook Pro persistently will not connect to my MiFi Verizon wireless router. The message "connection timeout" appears. What is a connection timeout and how can I fix?

Hi there terri900!
You may want to try configuring your router settings to match the recommended settings for iOS and OS X devices, which can be found here:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
You may also find some helpful information for troubleshooting this issue in this article, which can help you with any manner of issues with Wi-Fi connections:
Wi-Fi Quick Assist
http://support.apple.com/kb/HT1145
Take care, and thanks for visiting the Apple Support Communities.
-Braden

My IPOD and Macbook Pro both will not connect to the Itunes store through Itunes says no internet connection, but I can connect through safari and I have a internet connection

My IPOD and Macbook Pro both will not connect to the Itunes store through Itunes says no internet connection, but I can connect through safari and I have a internet connection

As I mentioned above, I am not very tech savvy so I have no idea why a wireless protocol would be showing up there, I'm just listing everything I see in hopes that someone might know something I can try. This is why I am asking for help here - I'm not sure what has happened that has made me unable to connect, especially since it seemingly occured while nobody was using the computer.
I guess I should clarify that I'm not a total hillbilly- normally my firewall is set to 'on', but I set it to 'off' to try and troubleshoot the issues here as I was told that sometimes it can interfere with the computer's ability to connect to the internet. If this is not the case and firewall does not affect anything, I will turn it back on while I try to fix this.
I have tried the method you mentioned above a few times - I actually contacted my ISP earlier this week and they recommended resetting the router like that. They didn't mention any known network issues.

Satellite Pro P10 will not remain on mains power

Similar Messages

Maybe you are looking for