Screen drop out and defaulting

Try reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

Similar Messages

I dropped my ipad and the screen blacked out and could not be turned on even after pressing the sleep and home button

I dropped my ipad and the screen blacked out and could not be turned on even after pressing the sleep and home button.
I tried connecting the device to my computer and itunes said that it could not identify my device.

What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

Hi, my iPad 2 keeps dropping out and going back to blank screen, I then have to enter my password again, start downloading or reading and it happens again. I have reset the iPad but it is still the same.

Hi, my iPad 2 keeps dropping out and going back to a blank screen. I have to again enter my password and go back to what I was doing and then it happens again, I have tried resetting and nothing has changed.
Thanks
Ron

First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without be charged again. Also, if you have IOS-7, read this.

CS3 exporting drop outs and red screen flashes when exporting via Media Encoder

Hi forum
I have been using Premiere Pro CS3 for a long time on my dual core PC with no issues. Suddenly, I am now getting a major issue i MUST get sorted asap for a client is waiting for the final video.
It is a HDV (1080i, 25fps) project/timeline. An 8 minute video has been put together in this and every time I try to export as either MPEG2 (Blu Ray) or WMV, I am getting pixelation in certain places usually around certain cuts, or horrible red blocky pixels filling up the screen for a second or two. They seem to come always at the same point. They don't happen when i render the timeline or show up when playing the edit itself in the timeline - just when i playback the exported video in premiere or in Windows Media Player.
To try a workaround I exported the whole video as high quality MPEG2 (blu ray - 30mbps), which I brought into a new sequence, then I exported small sections where this problem was happening as Uncompressed Microsoft AVI and called them "patch 1", "patch 2" etc. and brought them back in and overlayed over where the problems were occuring. The short Uncompressed AVI patches seem to have exported with no glitches, so theoretically I thought I had a clean good timeline in my new sequence made up of the MPEG 2 video overlayed in the dodgy places with uncompressed AVI "patches". However, trying to export a new MPEG 2 master from this has created the same problems, in the same places!!! Still drop outs and still those horrid red flashes filling the screen. Not always as bad, and some places where there were problems are ok, but I am still left with most of the problems still there.
I am now trying to export the whole video as an AVI uncompessed but dont know if this will work and will take a very long time.
I do have Saphire plugins, but they are not being used in this new sequence so therefore could that be a possible problem? I thought perhaps it was the brightness/contrast filter etc so removed that from some of the problem areas, and it helped on some of them, but not on others, so not sure its anything to do with my plug in or filters.
Any help would be greatly appreciated.
thanks, James

This topic is about a year old, but I thought I would reply because I just experienced this problem very recently and stumbled upon an easy solution.
Problem: When using Adobe Media Encoder to create an HD or .m2v video file, a bright red screen will flash followed by a mashup of red blocks/pixels somewhere within the file you've just encoded. This phenomenon lasts for exactly 10 frames before clearing up. Most likely, you won't see this problem until you import the encoded file into Adobe Encore. It shows up on the timeline, the preview monitor and the DVD itself. It occurs on edits that the system reads as being corrupt or when a flash bulb goes off from a still camera. Both instances make the encoding process go haywire.
Solution: Encode your HD or .m2v file with CBR (1-pass) bitrate encoding rather than VBR (2-pass). Don't worry about losing any quality in your video or creating unnecessarily large file sizes with your new renders. I guarantee you won't see much of a difference, if any. I can't explain why this solution works. It just does.
Hope this helps you as much as it did me.

My mozilla firefox search engine always defaults to amazon...how do I get just basic mozilla firefox search screen with out the default to amazona?

My mozilla firefox search engine always defaults to amazon...how do I get just basic mozilla firefox search screen with out the default to amazon.com for everything ?

Change the search plugin in the search bar to something else and you can search with that.

Broadband Dropping Out and Connection Speed Decrea...

Sorry to be a pain but I am back here again.
Since the last issue with speed, connection drop out and noisey line which required an underground cable to be partly replaced, all has been fantastic and no problem to report. Many thanks to those who were involved in helping with getting that issue resolved.
About 10 days ago the broadband started to drop out at random times but not too often. The broadband hub light would go out for about 15 seconds before returning. My connection would automatically resume and no great problem. It has since become more of a problem and pain.
The frequency of drop out increased with a sort of pattern. Last week an example would be drop out at 11:50 am, again at 12:40 and once more at 1:30 pm. Each time the connection returned my computer icon for wifi would be a warning triangle. I clicked on the icon and would get a message 'limited connection'. The only way I could connect again would be to click the icon and select to disconnect and then connect, making sure a 'tick' was in the box for autoconnection. A bit more of a pain than before but usable. It got more of a problem over the next few days.
The frequency of drop out increased. This became a right pain when trying to purchase things online as I could not be sure in the purchase had been completed or if I tried again would I get two lots? Upon broadband connection returning I would not be able to 'auto connect' but would get the warning triangle of 'limited connection'. I tried the click to disconnect and reconnect but it failed to work. I ended up shutting down the laptop, waiting before powering up. This failed to work as all I would get is the warning triangle and 'limited connection'. The only way I could reconnect was to press the 'restart' button. This worked but it got worse.
The next day the broadband connection would drop out every couple of hours. It got to the point that even pressing the 'restart' button would not allow me to connect. I tried three times and gave up. I had to resort to pressing the very small 'reset' button on the back. This cured the problem for about 12 hours before the drop outs started again.
It is now a case of 50/50 if I can connect to the broadband again after a drop out. It is getting quite frustrating. I only used the small 'reset' as a last resort. I have noticed that the speed of the connection has started to drop down also.
Each time the hub drops broadband and I can auto connect and do not press any hub button, the timer has reset to zero days and zero hours. I know it takes about a week for the connection to settle. I do wonder if these drop outs are messing the connection settings for my line speed? The line used to be rated at 21 Mbps but has decreased to 17 Mbps, my actual connection used to be 19 Mbps but struggles to reach 14 Mbps. It is slowly dropping with each and every drop out.
I also looked at the event log in the hub. Just before each broadband drop out I see a external connection is made with the initials 'CWMP' followed by 'event code 1 boot' or 'event code 6 connection request' or 'event code 4 value change'. Straight after the broadband connection drops out with out fail.
All I can seem to find out is that the external connection is either the hub connecting to the server or vice versa? As for the codes? I have no idea at all.
I only ever resort to pressing 'restart' if I cannot connect to my hub. I have only pressed the 'reset' as a last resort as nothing else worked to allow me to reconnect.
Can anyone offer any help or best a permanent fix?

I connected to the test socket and used a wired connection for the speed test and hub stats.
The hub position and run of cables are the same as when the last engineer advised as the best set up.
Since my last post I have checked the event log and 'CWMP' has made at least two remote connections but the hub did not drop broadband connection. The broadband has been stable but just slower than usual, as you stated due to the drop outs/disconnections.
I guess a case of wait and monitor to see if the problem has resolved itself?
Will the speed automatically return to the usual 18 to 19 Mbps? or will something else have to be done to reset it at the exchange/server?
Here are the hub stats from this morning.
Connection Information
Line state:
Connectedppp0_0
Connection time:
2 days, 00:23:43
Downstream:
16.69 Mbps
Upstream:
1.024 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
9.5 dB / 7.1 dB
Line attenuation (Down/Up):
10.3 dB / 6.7 dB
Output power (Down/Up):
19.8 dBm / 12.4 dBm
FEC Events (Down/Up):
4947 / 0
CRC Events (Down/Up):
11 / 11
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
377 / 48
Error Seconds (Local/Remote):
72 / 21

Iphone screen popped out and glass broke. wont turn on

My iphone 4s screen popped out and the glass broke in one corner. Wont turn on. Can this be repaired?

do they replace it with the iphone 4s? I am 2 months shy of a verizon upgrade when I could get a more up to date phone. SO I would prefer a more current phone and 149 seems steep as an intermediary solution. Any advice

My screen blacks out and computer starts up again due to an error. Anyone any suggestions what could case this?

My screen blacks out and computer starts up again due to an error. Anyone any suggestions what could case this?

Hello nattygrimm,
I was looking into the issue you are describing and found a great resource to try and fix the issue without having to re install the OS. It is an article called Mac OS X: How to troubleshoot a software issue found here: http://support.apple.com/kb/HT1199.
I recommend starting here:
The first and easiest test to try is to see if the issue affects a different user account on your Mac. Each user account has customized preferences and other items stored in its home directory. You'll first need to create an additional user if one does not already exist (follow steps a-h below). Then, log out of the current user and test the issue in the new user account.
If this resolves the issue, there may be an issue with a file in the home directory of the original user account.
From the Apple menu, choose System Preferences.
From the View menu, choose Accounts (or choose Users if using Mac OS X v10.2 or earlier).
Click "+" (or click New User if using Mac OS X v10.2 or earlier).
Give the new user a name and short name.
Mac OS X v10.3 or earlier only: Click the Password tab, and give the user a password.
Mac OS X v10.3 or earlier only: Click Security.
Select the checkbox for "Allow user to administer this computer". This makes the user account an administrator.
Click OK, or quit System Preferences.
Work your way down the article as needed.
All the best,
Sterling

My screen blacks out and mac goes to sleep.

My screen blacks out and mac seems to go to sleep. Starts up again after 30 seconds. This occurs after installing mountain lion.

Intel-based Macs: Resetting the System Management Controller (SMC)

Help me!:audio keeps dropping out and coming back in while importing clips

While importing from my camera (brand new Canon Xl-2) to imovie, the audio from the tape keeps dropping out and coming back in for some reason.This happens with all my tapes. I've tried using a head cleaner and that didn't help. I'm using a Maxtor external hard drive to save the project on. The project itself is kind of big (about 80 GB) Can imovie support projects that large? Could this be a problem with my processor?
I'm just frustrated beyond belief right now. Any help you can give would be greatly appreciated. Thanks!
these our my specs: Processor: 800 mhz. Memory: 1GB SDRam. The disk space icon at the bottom of imovie says i have 151 GB of disk space left.
powermac g4 Mac OS X (10.4.5)

Hi e
With a slow computer one has to minimize the hassle.
I would
- repair permissions
- cheque that nothing else is taking resourses from the job (energy saver,
screensaver, File Vault etc.)
- I would move material to my ext hd so that I got > 80Gb free (for a 80Gb
project)
- nothing else connected than my Mac + Camera and import.
Yours Bengt W

My iphone 5c screen went out and its just a black screen ive tryed a hard reset and nothing still when i plug the charger in it dings and ive hooked it to itunes and restored it still nun do i need to buy a new screen or is something else wrong?

My iphone 5c screen went out and its just a black screen ive tryed a hard reset and nothing still when i plug the charger in it dings every few secs and ive hooked it to itunes and restored it still nun do i need to buy a new screen or is something else wrong?

If your iPod Touch, iPhone, or iPad is Broken
Apple does not fix iDevices. Instead, they exchange yours for a refurbished or new replacement depending upon the age of your device and refurbished inventories. On rare occasions when there are no longer refurbished units for your older model, they may replace it with the next newer model.
ATTN: Beginning July 2013 Apple Stores are now equipped to do screen repairs/replacements in-house on iPhone 5 and 5C. In some cases while you wait. According to Apple this is the beginning of equipping Apple Stores with the resources needed to do most repairs for iPhones, iPads, and iPod Touches that would not require major replacements. Later in the year the services may be extended as Apple Stores become equipped and staffed with the proper repair expertise. So, if you need a screen repaired or a broken screen replaced or have your stuck Home button fixed, call your local Apple Store to see if they are now doing these in-house.
You may take your device to an Apple retailer for help or you may call Customer Service and arrange to send your device to Apple:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support: Contacting Apple for support and service - this includes international calling numbers.
You will find respective repair costs in the appropriate link:
iPod Service Support and Costs
iPhone Service Support and Costs
iPad Service Support and Costs
There are third-party firms that do repairs on iDevices, and there are places where you can order parts to DIY if you feel up to the task:
1. iResq or Google for others.
2. Buy and replace screen yourself: iFixit

When in googlemail firefox keeps connecting dropping out and reconnecting,and crashing.

When in googlemail inbox, Firefox constantly keeps dropping out and reconnecting,(as seen in the tab) and often crashes when one is writing or sending a message.

Try to start Firefox with the about:blank page by creating a copy of the current Firefox desktop shortcut and add a space and <b>-url "about:blank"</b> to the target field.
Try to delete the sessionstore.js file in the Firefox profile folder to prevent restoring the crashed session.
*C:\Users\<user>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\
*http://kb.mozillazine.org/Profile_folder_-_Firefox
The "AppData" folder in Windows Vista and later Window 7+ versions and the "Application Data" folder in XP/Win2K are hidden folders.
*http://kb.mozillazine.org/Show_hidden_files_and_folders

My Mac screen blew out and is frozen

After the first few screen freezes, the screen would be pixelated and I had to unplug my computer and restart. It would turn on successfully but my whole screen would have little pixel squares. I ignored that fact and was just happy my computer turned on. Moments later, my screen blacked out and I tried to do the same thing. Only this time the screen stays on to the open apple screen with pixels everywhere.. I don't know how I can solve this problem or if it can even be solved..

I can't run the hardware test or do anything at all.. I turn my iMac on and it goes I a white screen with the apple icon and then goes to a blank white screen. I would like to get it checked out but the nearest apple retail store is 2 hours away..

Two days before my iphone 5 battery was expand and display screen came out and now there has some gap between frame and display.so how it will happen and i already got before months.now i need to backup all the data to icloud before through out.

two days before my iphone 5 battery was expand and display screen came out and now there has some gap between frame and display.so how it will happen and i already got before months.now i need to backup all the data to icloud before through out.
https://www.dropbox.com/home/iphone
https://www.dropbox.com/home/iphonehttps://www.dropbox.com/home/iphone

Make an appointment at the genius bar of your local Apple Store. The phone has a 1 year warranty. If it's no longer under warranty, a replacement is $269.

Is there a solution to the Bluetooth dropping out and disappearing on Lion 10.7.5?

Always drops out and disappears from preferences panel. There is a lot about this on the comunity but i have yet to discover a solution. Anyone?

You managed to place an item in the toolbar that has since been trashed. The solution is simple. Right click (or control click) on the toolbar and select Customize Toolbar... Now you can drag the question mark off the toolbar and release the mouse button. It will poof (disappear).

Screen drop out and defaulting

Similar Messages

Maybe you are looking for