Scrollbar does not get active

Hi,
I am using XY graph to display temperature Vs. Timestamp. I need to use scroll bar for my graph. I have enabled scroll bar for X-axis but it doesnt seem to work. It is always disabled and grey. I need data points on my plot to be spaced out so that I can analyse and see the data in a better way. Also LV reads the whole data log file at once. I need to delay it for each data point and display it on graph. Can anybody help me out with this problems.
Thanks in advance,
Ratnesh
Attachments:
01062005.zip ‏117 KB

The reason your scroll bar is disabled is because you are displaying the entire data set. If you were to enter a different start or stop time, the scroll bar would be displayed. To enter a different start or stop time time, just highlight which one you want to change and type in a new value. If you want to do it programatically, turn off autoscale of the X axis and then you can use a property node to set x min and x max. If you want to display data point by point like a chart does, what I would recomend is that you read in the entire data set like you're doing but instead of wiring it directly to the XY Graph, wire it to a for loop with a wait statement inside. There is a shipping example called XY Chart that you should look at. It uses a subVI called XY Chart Buffer that manages the data. If you put the subVI and the graph inside the for loop, you should get what you want.

Similar Messages

  • Function Module Not Getting Activated

    Hi,
    We are using a customised function module which we are calling in a user exit. We would like to call this function module in update task in the user exit to populate data in a custom table.
    We have given the following parameters to the function module
    Import Parameters
    ITAB     LIKE     ZPRUNDAT
    Export Parameters
    l_subrc     TYPE     sy-subrc
    On the attributes tab of the function module, Update Module has been selected under processing type.
    When we try to activate this function module we get the following message
    EXPORTING parameters are not allowed in the update task.
    and the function module does not get activated. What should we change to get the function module activated?
    Mick

    Hi,
    Please try this....
    In function module
    In tables Section add this...
    RETURN TYPE BAPIRET2 and then activate.
    if its useful reward points

  • Audigy 4 Pro - I/O Hub does not get any po

    Hello all,
    I purchased an Audigy 4 Pro a few days ago and I cannot get the external hub to power on.
    This somewhat sumarizes what I tried so far:
    . Uninstalled all drivers and software of my old Soundblaster Li've 5. Platinum
    2. Also removed all entries of the old soundcard from Device Manager
    3. Powered down the PC fully, took out the Li've 5. and powered it back on and logged on to my Windows XP (SP2).
    4. Just to be sure before installing the drivers for the Audigy 4 Pro I cleaned out the cookies, temporary internet files, all other Temp folders, the Prefetch folder and also ran a program to clean the registry.
    5. De-activated my Norton AntiVirus Corporate Edition's Real-time protection, it's services and also my ZoneAlarm Pro from starting up the next time I reboot Windows.
    6. Powered down the PC again, took the power cable out, made sure there was no power whatsoever left and carefull inserted the Audigy 4 Pro card in an empty PCI slot.
    7. Connected the larger AD_Link to the card, then to the hub
    8. Connected the smaller AD_Link to the card, then to the hub
    9. Finally connected the power convertor cable to a free systems power unit
    0. Double-checked the entire hardware setup a few times and power the PC back on
    . Windows XP detected and installed the OHCI Compliant IEEE 394 Host Controller and the 394 Net Adapter
    2. Canceled to proceed looking for a driver when it found the Audigy 4 Pro card
    3. Installed the drivers and applications that came with the Audigy 4 Pro. Everything went smooth - no error messages during the installation.
    4. Rebooted PC after prompting to do so.
    5. With ZoneAlarm and my Norton Antivirus de-activated, all drivers and programs installed properly the external I/O hub does NOT get any power. I also made sure to check this with the remote control.
    I have ofcourse no sound coming out that hub when plugging in my headphone and also cannot use my microphone.
    6. I ran the Diagnostics program that was installed automatically with the other Creative applications: It claims there aren't any problems.
    7. Powered down the PC again, checked all connectors, powered the PC up again: Same problem... no power.
    8. Installed the latest 4-in- drivers found on viaarena.com: Same problem
    9. Uninstalled and reinstalled the drivers and applications: Same problem
    20. Uninstalled and reinstalled the drivers and applications after taking out all other PCI cards and placing the Audigy 4 Pro card into an other PCI slot: Same problem
    2. Set my BIOS to factory defaults: Same problem
    22. Formatted the PC and reinstalled Windows XP (SP) with every update thinkable... Same problem
    23. Formatted the PC AGAIN ( ! ) and reinstalled Windows (SP2) with updates .... Same problem
    Another problem: Sent a detailed e-mail to Creative Support Europe.... Still NO respons after 48+ hours.
    Anyone else should have a solution I would appreciate trying out, or if all fails I'll go for a Terratec model.
    Thanks in advance!
    PC Stats: Asus A7V266 - VIA KT266 Chipset (VT8366 North Bridge with VT8233 South Bridge) / BIOS version: 0 / AMD Athlon .4GHz / 52Mb
    Message Edited by HilTek on 07-05-2005 :04 PM

    Amazing, I got mine about 3 days ago and have been pulling my hair out trying to resolve the same problem. I have checked power connections, reinstalled drivers. I think something is wrong with the box. I tried to call support yesterday, which was a Saturday, but they aren't available til Monday. I guess I will call them Monday. Let me know if you find anything out in the mean time.
    Thanks
    John
    AMD Athlon(tm) 64 FX-57 Processor
    A8N-SLI Premium
    NVIDIA GeForce 7800 GTX
    GB RAM
    WIN Pro x64

  • Solution Manager does not get service definitions from SAP in self diagnosi

    Hi,
    In our production solution manager transaction solution_manager, self diagnosis we are getting a warning message on our development solution manager. 
    Solution Manager XXX does not get service definitions from SAP.
    The production Solution Manager is the master in SDCCN for the test Solution Manager.  In the test Solution Manager, the scheduled task REFRESH SERVICE DEFINITIONS has task System ID of O01.  It is pointed to RFC destination SDCC_OSS, not the production Solution Manager system.
    It gives the same warning if I point the task to the production Solution Manager system.
    Has anyone seen this before?  Any ideas?
    Best regards,
    Russ

    Hi,
      i guess have you activated SDCCN from your solution manager system too?
    if not please activate. since that setup helps solman retrive the service definitions used in SDCCN from SAP (SAPOSS).so this ultimately allows you to set solution manager system as Master, so all the satellite system get the service definition from solman and do not need a direct SAPOSS connection.
    and Please check this Note 1143775 - SAP service content update
    the wiki for trouble shoot ["EarlyWatch Alert is Red Flagged - how to resolve" |http://wiki.sdn.sap.com/wiki/pages/viewpage.action?pageId=228262728]
    please check.
    Thanks,
    Jansi

  • OBUSOBJECT Blocked for conversion and not getting activated

    I  have changed the infoobject OBUSOBJECT attribute 0Mainusage fron <b>navigational to display</b> and then tried activating the OBUSOBJECT , , OBUSOBJECT If in the former active version this IO had 0MAINUSAGE as a nav attribute, now, in a revised version, this is just display attribute. surprise that the OBUSOBJECT couldn’t be activated by installation.
    Please tell me what are the steps now to resolve this. i want to actiovate the OBUSOBJECT in either old active version or activate with new revisions. i am just stuck since it is not getting activated.
    please tell if i go to se16 and <b>sdokmia</b> table in first row i put BW* and then in
    3 rd row i put what attribute since when i put  0Mainusage (/BI0/OIMAINUSAGE)
    it does not show any record what should i put there?? and then what is the next step. if you can help me step by step.
    please help me to resolve this
    Regards
    Soniya Kapoor

    Hi Soniya,
    If i have understood you properly, you have one attribute of the infoobject navigations, which u changed to display and tried activating and its not getting activated. This particular attribute is used in some othe cube as navigational attribute as well. Without deleting those references, u want to change the infoobject.
    If thats the case, you will not be able to activate ur infoobject. All the reference have to be revoved before activating the object. Sorry for that
    Regards
    Sriram

  • Moving Average Price does not get updated for Project Stock

    Hello Experts
    We have an Engineer-to-Order implementation for our client. Accordingly procurement is done per project. Each Project issues its PRs which are then converted to POs and recieved into Project Stock.
    While assigning the material to the Network activity in Project (using material component) the system uses the price found in the material master (MAP or STD) as a planned cost appended to the project.
    Problem:
    while procuring the material, when we receive it into Project Stock (Mvt 101 Q + ) the Moving Average Price in the material master does not get updated. this way all newly created material master will never have a moving average price, thus whenever we try to assign them to the project we receive an error message (Cost for Material Component ###Mat.Num### cannot be determined.
    Question:
    How can I get the system to update moving average price (for all types of stock) based on procurement for project stock.???
    Your help is kindly appreciated.

    I'm sorry for the confusion
    Case:
    The T-code is CJ20N Project Builder in PS module
    we are assigning material components to network activities under a certain WBS element in the project.
    there is a function in the Project Builder to calculate the cost of a network. it uses the costing variant assigned to the network which is PS02 (We get the error here)
    The costing variant has a valuation variant which lists a series of strategies  to get the material price. Planned 1 if not then STD if not then MAP. (you can choose between many options via a drop down menu) you can choose 5 consequent options.
    The MAP that the valuation variant is coded to get is the Plant Stock MAP -- Or the Project Stock MAP but only Per WBS element.
    The MAP that the Actual postings update is the Project Stock MAP only Per WBS element.
    This means that if you use a material component to purchase material 123 Acc.As. Q for WBS X for 10 $ then you try to assign a new material component with the same material 123 to WBS Y, the system will not get a MAP. because it's stored in QBEW per WBS element.
    This way the system will never get the MAP right.
    However, we don't always use project stock to procure for projects, for some requirements we can assign and use plant stock as well for Projects. that way we need the MAP from plant stock.
    In the Valuation Variant you can use a User Exit Strategy. The user exit's name is COPCP005
    My Suggestion is:
    Use the User Exit COPCP005 to calculate the { Total value / the total quantity (MAP) from QBEW + Total value / total quantity (MAP) from MBEW } / 2
    which is the MAP for both plant and project stock together, since that we are going to use both.
    Q: Is this correct !?

  • The GPS sendor does not get a fix.

    I have tested the GPS sensor from time to time.
    It does not get a fix, and flashing once a second.
    I made it to face to open sky, so I do not think it did not find satellites.
    So I get the following log, when I run the demo program.
    AdaFruit GPS Sensor: position data = 075847.799,,,,,0,0,,,M,,M,,*46
    AdaFruit GPS Sensor: Badly formatted latitude number
    Does anyone have an idea to fix it?

    Hi -
    The sensor does take awhile to locate the satellites, even it is is facing the open sky - sometimes as long as 15 minutes. However, in a dense urban setting, even then it has a hard time getting the signal with the built in passive antenna.
    I recommend considering purchasing an active antenna, like this one.  Be sure to also purchase the adapter cable that Adafruit recommends.  Using this antenna, I was able to get a signal inside of building in downtown San Francisco.
    Regards,
    Tom

  • I bought and legally own PS CS3. Installed on a desktop and the machine died completely. Downloaded a trial of CS3 from Adobe site. Went to activate and said too many activations. Activate over the phone. EXCEPT Adobe does not handle activation issues ove

    I bought and legally own PS CS3. Installed on a desktop and the machine died completely. Downloaded a trial of CS3 from Adobe site. Went to activate and said too many activations. Activate over the phone. EXCEPT Adobe does not handle activation issues over the phone. Adobe doesn't care about their older products - they don't care that I spent hundreds of dollars for CS3. This is truly disgusting corporate behavior. Is there anything I can do? We aren't all rich photographers. I paid a great deal of money for this product. Is it now useless?Thank you,
    James Scott

    HI James please contact the Adobe Chat Team for activation issue
    kindly do the mentioned steps as follow in order to get hold of chat rep of adobe
    Go to www.adobe.com/getsupport
    select the product as adobe creative suite - then select the issue as adobe id and sign in - and then click on still need help contact us then you will be able to find chat option and they will help you with the chat issue

  • Version 1 is not getting activated in PR and PO

    We are using release strategies for PR and PO, along with we have to activate Version Management, which we have already activated (Active Version and 0 Version).
    But now Version 1 is not getting activated in system only Version 0 is appearing in PR or PO, even after revoking PR or PO system is reflecting all the changes in Version 0. I have even taken print out of PO but new version couldnu2019t triggered. All the relevant fields have been mentioned in version relevant fields of PR.
    The entire required configuration has been done, I have gone through whole forum many members have encountered the same problem but solution is not provided to any one. Kindly suggest in this regard.
    Full points will be awarded.

    Amir Hassan wrote:
    We are using release strategies for PR and PO, along with we have to activate Version Management, which we have already activated (Active Version and 0 Version).
    >
    > But now Version 1 is not getting activated in system only Version 0 is appearing in PR or PO, even after revoking PR or PO system is reflecting all the changes in Version 0. I have even taken print out of PO but new version couldnu2019t triggered. All the relevant fields have been mentioned in version relevant fields of PR.
    >
    > The entire required configuration has been done, I have gone through whole forum many members have encountered the same problem but solution is not provided to any one. Kindly suggest in this regard.
    >
    > Full points will be awarded.
    Amir Hassan wrote:
    We are using release strategies for PR and PO, along with we have to activate Version Management, which we have already activated (Active Version and 0 Version).
    >
    > But now Version 1 is not getting activated in system only Version 0 is appearing in PR or PO, even after revoking PR or PO system is reflecting all the changes in Version 0. I have even taken print out of PO but new version couldnu2019t triggered. All the relevant fields have been mentioned in version relevant fields of PR.
    >
    > The entire required configuration has been done, I have gone through whole forum many members have encountered the same problem but solution is not provided to any one. Kindly suggest in this regard.
    >
    > Full points will be awarded.
    Amir Hassan wrote:
    We are using release strategies for PR and PO, along with we have to activate Version Management, which we have already activated (Active Version and 0 Version).
    >
    > But now Version 1 is not getting activated in system only Version 0 is appearing in PR or PO, even after revoking PR or PO system is reflecting all the changes in Version 0. I have even taken print out of PO but new version couldnu2019t triggered. All the relevant fields have been mentioned in version relevant fields of PR.
    >
    > The entire required configuration has been done, I have gone through whole forum many members have encountered the same problem but solution is not provided to any one. Kindly suggest in this regard.
    >
    > Full points will be awarded.
    Amir Hassan wrote:
    We are using release strategies for PR and PO, along with we have to activate Version Management, which we have already activated (Active Version and 0 Version).
    >
    > But now Version 1 is not getting activated in system only Version 0 is appearing in PR or PO, even after revoking PR or PO system is reflecting all the changes in Version 0. I have even taken print out of PO but new version couldnu2019t triggered. All the relevant fields have been mentioned in version relevant fields of PR.
    >
    > The entire required configuration has been done, I have gone through whole forum many members have encountered the same problem but solution is not provided to any one. Kindly suggest in this regard.
    >
    > Full points will be awarded.
    Amir Hassan wrote:
    We are using release strategies for PR and PO, along with we have to activate Version Management, which we have already activated (Active Version and 0 Version).
    >
    > But now Version 1 is not getting activated in system only Version 0 is appearing in PR or PO, even after revoking PR or PO system is reflecting all the changes in Version 0. I have even taken print out of PO but new version couldnu2019t triggered. All the relevant fields have been mentioned in version relevant fields of PR.
    >
    > The entire required configuration has been done, I have gone through whole forum many members have encountered the same problem but solution is not provided to any one. Kindly suggest in this regard.
    >
    > Full points will be awarded.
    Dear Amir,
    in pr version management , control data :select version active,version 0 ok, & external ok. &
    field selection : reason required,short text req., requester req., external number & posting date are optional & save.
    even with release strategy there is no problem
    create a pr & save it.After release it. change the pr
    after u canfind the versions 0 & 1.
    in po version management , doc.category f doc.type nb pur.org xxxx ,control data :select version active,version 0 ok, field selection : reason required,short text req., requester req., external number & posting date are optional & save.
    go to Set Up Change Displays as per standard nb is already there no need to change & category is blank
    in category u have to maintain f(is for po) & save it.
    create a po & save it.After release it. change the po
    after u canfind the versions 0 & 1.
    Regard's
    Raj.

  • G/L Account mentioned on line level does not get hit in Journal entry on GRPO and AP Invoice in SAP B1 9.0 PL - 11

    Hi,
    G/L Account mentioned on line level does not get hit in Journal entry on GRPO and AP Invoice in SAP B1 9.0 PL - 11
    I am creating an independent AP Invoice, there are two issues:
    1. On line level G/L Account field is not open for selection
    2. I have then selected and updated the account on Form Settings. Same account gets updated on line level.
         In Journal Entry selected G/L account on line level shall be hitted. But it does not put any effect on JE. Accounting is set by Warehouse. It picks up accounts from warehouse only.
    Need help its urgent.
    Thanks in advance.

    Invoice is Item Type.
    G/L Accounts are set by Warehouse. But if explicitly we are want to change the account on line level in that case, it is not getting reflected in Journal entry. On AR Invoice same scenario works perfectly. On line level I can change the accounts explicitly and have the effect on Journal entries.
    Issue seems to be on AP side only.
    As required please find attached the screen shots.
    JEwith mapped GL Account on Warehouse
    JEwith different GL Account on line Level via Form Settings
    Thanks & Regards
    Sonil

  • I am part of a family sharing setup.  Can I have my own payment method so the organizer does not get charged for my purchases?

    I am part of a family sharing setup.  Can I have my own payment method so the organizer does not get charged for my purchases?  If so, how do I set this up?

    Yes.  Just redeem gift cards so that your own account always has a sufficient credit balance.  Here is how it works:
    Family purchases and payments
    After you set up your family, any time a family member initiates a new purchase it will be billed directly to your account unless that family member has gift or store credit. First, their store credit will be used to pay the partial or total bill. The remainder will bill to the family organizer's card.

  • Iphone 3GS no battery charging icon, does not show charging, does not get recognized by computer or Itunes.

    Iphone 3GS no battery charging icon, does not show charging, does not get recognized by computer or Itunes, have tried restore mode & DFU mode. Bad battery or port?

    iPhone not appearing in iTunes

  • I can no longer get to Facebook Via firefox It comes up loading in the tab but does not get any further one minute it was working the next it was,nt should I try uninstalling firefox then reinstall or does anyone know what could of happened thanks

    # Question
    I can no longer get to Facebook Via firefox It comes up loading in the tab but does not get any further one minute it was working the next it was,nt should I try uninstalling firefox then reinstall or does anyone know what could of happened thanks

    * "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
    * "Remove the Cookies" from sites that cause problems: Tools > Options > Privacy > Cookies: "Show Cookies"
    Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
    * Don't make any changes on the Safe mode start window.
    See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

  • When I send a text message to my husbands iPhone he does not get it

    When I send a text to my husbands iPhone he does not get it.  It worked before the new update.

    Either one of you needs to uncheck the other's phone number under settings&lt;messages&lt;send &amp; receive or one of you needs to sign out of the apple ID in iMessage settings altogether by pressing the apple id on the page and choosing 'sign out'

  • My itunes does not get the names of all tracks which i import.

    When i import a cd into itunes, it does not get any track names. Why is this.
    Also, itunes does not connect to the music store. It tells me that i should check my connection etc etc. Are these problems related, and what can i do to fix it?

    Let me guess, did you just install/upgrade iTunes?
    If so, then it's surely your security software (firewall, web accelerator, privacy filters, etc) that is blocking iTunes.
    The iTunes "upgrade" is actually an uninstall, then total new install, of iTunes and QuickTime. Many security packages such as Norton, Zone Alarm, Google Web accelerator, McAfee, PCillin (...the list is long) see this new iTunes install as a malicious threat, and block out the previous settings without telling you.
    Go to your security software vendor's website and see if they have directions for allowing iTunes & QT back in the list of programs allowed to access the internet.

Maybe you are looking for