Sending message on RS232 with interval 1 ms

Hi there,
I´m using the RS232 to communicate to a motor. The Baud rate is 19200, 8 data bits, 1 stop bit, no parity.
A requirement of the motor is between each byte there should be an interval of 1 ms.
How can I set the interval in LabVIEW?
Thx

I think there are some misunderstandings in some of these answers. I'm pretty certain that what the op is asking for is the same thing as the character delay setting in Hyperterminal. The delay is a minimum and what has always worked for me is the simple code below. To add line delay, place a Delay function outside the loop to be executed after the while loop finishes.
Message Edited by Dennis Knutson on 03-19-2010 09:06 AM
Attachments:
inter character delay.png ‏41 KB

Similar Messages

I bought an unlocked iphone 4s and it is not sending messages or emails with pictures taken with it. What do I have to do?

How do I send messages and emails with pictures attached from my iphone 4 s?

Contact your Carrier and check you MMS enabled on your Plan.

I can connect to 3G, but cannot send messages or call with my iphone 4.

I can connect to 3G, but cannot send messages or call with my iphone 4.

SMS and calls are carrier features. Check with your carrier

Strange bug when sending messages in parallel with same sender component

We have one sender business system sending messages to two different interfaces in parallel using an asynchronous soap channel : Interface1 and Interface2. In this scenario the Interface1 messages appear to be conflicting in some way with the Interface2 messages. A certain percentage of the Interface1 messages incorrectly receive a receiver system which equals the receiver configured for Interface2. This causes the Interface1 messages to fail since there is no defined mapping our routing channel to the Interface2 receiver system for that interface.
We have confirmed that this bug only exists when the same sender business system is used. We ran a test using different sender systems and all the messages went through successfully. Today we ran a test moving both interfaces over to a different sender. This test reproduced the issue but in a slightly different way. This time the Interface2 messages were corrupted with the receiver from Interface1.
We also ran some load tests to see how many messages need to be sent before the symptoms occur. We are able to reproduce the problem with as little as 15 messages for each interface. 10 messages for each interface works.
We have noticed that the messages that fail can't seem to load the sender agreement. We think this might be where the problem might be. I pulled the trace message below for the error cases:
<Trace level="1" type="T">Reading sender agreement</Trace>
<Trace level="1" type="T">Message does not contain a sender agreement</Trace>
<Trace level="1" type="T">Inbound validation by Integration Engine does not take place</Trace>
For the successful messages the trace looks like:
<Trace level="1" type="T">Reading sender agreement</Trace>
<Trace level="3" type="T">Validation Mode = No Validation</Trace>
Has anyone ever seen this behavior? We have put in a ticket for the SAP support team, but I'm hoping someone here might have seen this and can tell me if there is patch.
Thanks,
Kevin

Hello,
We have one sender business system sending messages to two different interfaces in parallel using an asynchronous soap channel : Interface1 and Interface2.
You have to create two soap sender comm channels and two sender agreements. The reason for this is that interface1 is already binded using your sender agreement. Therefore, you will get an error/conflict for interface2 because it is not the interface expected by your only sender agreement.
Hope this helps,
Mark

Why can't send message to friends with imessage?

I tried to send messages to my friends with my touch, but after i typed in my friend's Apple ID (email address), it said this user has not registered. I have tried several other friends, but it did not work either. However, friend succeeeded in sending me a message. What is the problem? What is wrong?

Hello,
if you didnt find a solution yet, i'd like to ask if you enabled iMessage on your device? to enable it, you must first disable it, then enable again, just once, then you can use it, you friend should also do it...
i had this problem at first too, then searched on the web, and saw that we had to do this first...

My imessage isn't working when i send messages to people with iphones that have imessage it works with very few people, now it's starting to stop working with those people. help please.

my imessage doesn't work between my friends and i. i have a new iphone 5. my messages only work with some people. with others imessage doesn't work in the first place and now its starting to stop working with other people help please.
& yes we all have imessage on.

Hi there,
I see that you are having IMessage problems. Some of the problems might be:
- Your friends IMessage is not activated (you have to activiate it with your apple id)
- Your IMessage is not activated
Here is some links to another person`s Imessage problems:
https://discussions.apple.com/message/17301880#17301880
https://discussions.apple.com/message/20142285#20142285
https://discussions.apple.com/message/18988318#18988318
Hope that helps!

Can't send messages using 4s with iOS8

Wasn't able to send any messages right after I downloaded iOS 8 so I restored network settings and it fixed the problem. However I am having the same issue now and I do not want to have to go through this every couple of days. Any one else have this issue and find a resolution?
Applies to both wifi and over 3g.

Hello there, Tspong.
The following Knowledge Base article offers up some great, in-depth steps for troubleshooting issues with Messages:
iOS: Troubleshooting Messages
http://support.apple.com/kb/ts2755
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Cannot send message via iCloud with movie

Email is sent if I remove my embedded/attached 23MB Quicktime movie is removed but not with the movie - via iCloud.
and my other (non-iCloud) account doesn't send any mail at all.
What is problem(s), please? How to trouble shoot? TIA

Thank you for info, but I am struggling with using it.
I went into #3 stmp.me.com.myname[STMP] and made changes I wanted to be in conformity with instructions of iCloud: Mail server information.
     So now the Account info reads 1: Description = my email address at [email protected]
                                                      2:   Server name = stmp.me.com
                                                       3: Default port 587 was already active
                                                       4: Authentication = Password (my iCloud password from Keychain                                                                                                                                              access)
                                                        5: Username = my name
                                                        6: Password = (my iCloud password from Keychain access)
But got this alert: "Could not save changes. The servers marked with alert icons are in conflict and cannopt be saved. Two servers cannot share the same address and authentication settings.   Resolve the conflicts and try again."
I think (look but guessing) that my changes to #3 become in conflict with #4 -- and I don't see how to get out of the conflict (other than not saving the changes I made to #3 in accordance with iCloud: Mail server information.)
I am lost! Should I delete #4? confused and anxious . ....
(Sorry about confusing formatting of post but Apple won't let me show it like I want)
Message was edited by: pwwwayne

Mavericks Messages problem sending message: "not registered with iMessage"

I'm on MacBook Air(MBA) and recently installed Mavericks. I try sending a message from MBA MESSAGES to a person's cell phone number (they have an android phone). Their name appears in red and I get: "...is not registered with iMessage." So I was trying to read discussions in here and allot of them say Messages won't work unless a person has an Apple device- iphone, Mac, etc. I want to know if that is true or if there is any other way to send from the MBA a message to them? I also tried from Messages on MBA to their gmail address, which they use on their android cell phone, and get same error.
Is there anyway a non-apple person can "register with iMessage" if they have an android phone?
I know I can email them, but I wanted a fast way for emergency purposes to get a MESSAGE to them from my MBA. Sometimes they can't talk on phone at some times, but are allowed to get instant message for emergency where they work.

Hi,
You have to have otr get an AIM or AIM valid name.
AIM stands for Aol Instant Messenger.
Apple IDs issued by Apple (Those ending in @mac.com or iCloud issued @me.com and @icloud.com) are valid as AIM Screen Names if the password is kept to 16 characters or less. (this is an AIM server limit)
Apple made an Agreement with AOL over the use of names over 10 years ago.
The Original .Mac ID (@mac.com) could be paid for or could be Trial Accounts.
Trial Accounts continued to work after the trial ran out. (i.e. the email stopped but the AIM Screen Name didn't).
The same was true of lapsed accounts.
When MobileMe started people could link, email-wise, their paid for .Mac accounts to the paid for MobileMe (@me.com) accounts.
Any @mac.com still works over the AIM service.
Now also @Me.com names worked - meaning some people had two valid AIM names - they are not liked for use with AIM just that the passwords will be the same.
With the end of MobileMe all those @me.com account died as far as AIM is concerned.
However you could link it to iCloud which effectively moved it to the iCloud server.
(i.e. they are iCloud issued @me.com ID instead of MobileMe ones)
Then Apple started to issue @icloud.com IDs
This could mean that some people have three working IDs for use with AIM (but all linked to one email Account at Apple).
NOTES
From Lion onwards (iChat 6 and Above) Apple have had the app also login in to Apple before it will allow the AIM Servers to "read" the password.
This applies to any iCloud issued ID - the "newer" iCloud linked @Me.com and @iCloud.com IDs
This means you cannot use those IDs in iChat 5 or earlier as those version only do an one point login only.
With the coming of iCloud other Apple IDs could be linked to iCloud which may have given you either @me.com and later an @iCloud.com ID as well or just an @icloud one if you were later to the party as it were.
Whilst in some cases this does give you two valid AIM Screen Name the originating Apple ID does not become one.
9:04 pm Saturday; February 8, 2014
 iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

I HAVE PROBLEM FOR SENDING MESSAGE FROM PC WITH MY...

HI
PC Suite says "Unable to send Text Message"
i have connect my mobile to my PC via USB Cable.
I've been using PC Suite to send txt for months no problems.
I format my mobile some days ago and reinstal PC Suite
but it cant do it anymore.
when i try to open my inbox or send a messege from PC
PC Suite try to install smsSync( text message support for PC Suite) to my mobile but it can`t and i recive a error message .
it messag prompted that instaliton to mobile wase failed and ask me try again ...
I can still browse the phone, sync with outlook... everything except send a txt.
Please Help me

What is the error message you get when PC Suite asks to install SMSSync onto the phone?
Just to pre-empt you, if it says installation failed for security reasons (or something like that), check the application settings - go to Menu, Tools, Manager, Options, Settings... here you should have software installation set to ON and Online certif check set to off.

My iPhone 4S will only send messages to people with iMessage? How do I fix it?

I got my iPhone 4S yesterday, and I tried texting my mom, who has hernimessage turned off, but it wouldn't. It told me it sent, but she never got it. And I can't receive any message that isn't an iMessage. How do I fix it? I tried turning off my iMessage. That didn't work.

Check Settings>Messages>MMS Messaging to see if it's set to "On". Check with your carrier to see that your account is properly provision. Check to see if your carrier is a supported iPhone carrier. Not all features work or work properly on unsupported carriers.
Best of luck.

IPad won't send message to number "not registered with iMes age" but iPhone 4 does! Why...

I often send and receive texts from my brother (who has a T-Mobile phone) but when I tried to send message to him with iPad2, it refuses and send "number not registered with iMessage" response. Now my iPad sends and receives me.ssages just fine with my and family member iPhones and iPad. What the **** is going on?

You can only send a Message on your iPad to another iOS device. Your iPhone, however, will convert the Message to a text message that can be received by your brother. This has to do withe the fact that the iPad is not a phone.

RWB:Error when sending message: 404 Not Found

Dear all,
"i am getting error: Error when sending message: 404 Not Found"
while testing from rwb > Component Monitoring > Non-Central Adapter Engines > Adapter Engine AIPID > test message >
with send message to = http://pid:50000/sap/xi/engine?type=entry - pi server url
sld buss system > pipeline url http://pid:50000/sap/xi/engine?type=entry (same)
and my id comm channel > target host > bid.xxx.com with service no
(adapter type: xi
adapter engine: Integration server
address type: url address
target host: bid
service no: 8000
path: /sap/xi/engine?type=entry
i am working in nw2004s system)
while testing cache connectivity test from rwb > Component Monitoring
i got error:http://docs.google.com/Doc?id=dcdrq9jt_0g6j35p
green: Integration Repository
green: Integration Directory
green: Integration Server - JAVA
red:Adapter Engine af.axd.aipid
yello:Integration Server - ABAP
Adapter Engine af.axd.aipid > Attempt to fetch cache data from Integration Directory failed; cache could not be updated
[Fetch Data]: Unable to find an associated SLD element (source element: SAP_XIIntegrationServer, [CreationClassName, SAP_XIIntegrationServer, string, Name, is.00.aipid, string], target element type: SAP_BusinessSystem)
[Data Evaluation]: GlobalError
though if i try to send message from rwb...> with send message to field with : directly to bi rather than pipeline url through bi than message send successfully but not getting into component monitoring.
what should i do?
best regards,
dushyant.
refer this forum: is rwb's send message to field = sld>buss system>Pipeline URL?
and
SXI_CACHE
@8O@ Error during last attempt to refresh cache
LCR_GET_OWN_BUSINESS_SYSTEM - NO_BUSINESS_SYSTEM
Smq2 = 0
Sm58 = 0

Hi,
If you are testing sending the message to the Adapter Engine, then the Send Message URL should be like this:
http://<server>:<J2EEport>/MessagingSystem/receive/AFW/XI
For your error, refer to the following threads:
Unable to find an associated SLD element
Unable to refresh cache contents in XI.
Unable to find an associated SLD element
Cheers
Manish

JMS send message

Hello,
in my message bean i have method with 3 BigDecimal parameters.
How can i send message from client with 3 BigDecimal parameters?
thanks for help.

No, but you can. use an object stream to serialize the message and you are
          all set.
          _sjz.
          "deezh" <[email protected]> wrote in message
          news:3d23fdbf$[email protected]..
          >
          >

Why won't Apple update its iPAD to send messages other than imessages?

Why won't Apple update its iPAD to send messages to phones with systems other and OS? I just purchased an ipad4 for my husband. This limitation is very frustrating. When I purchased and ipad3, I was told how to make the message go through as an SMS; however, this never worked. Had it not been for the fact that my husband has an iphone5 and getting an ipad with the same operating sytem simplifies things for him, it may have been better to get an Android tablet and switch phones!

I understand that, but it does have a message system, so it makes sense that you should be able to receive ALL messages via this system. I do have a phone and I can get them all, but if I sit down at the ipad to check messages, I only get those sent through imessage. Sorry, I'm venting and you probably can't do anything about it. Apple needs to wake up and figure out that if it doesn't change its protocol on the ipad, then people will switch to another system that does. Hoping that someone from Apple sees this.

Sending message on RS232 with interval 1 ms

Similar Messages

Maybe you are looking for