Servers are rebooting after patch syncronization

After approving MS-patches through WSUS all of a sudden servers are getting patched and rebooting. This is happening even after deadline has set. I have got a info like Microsoft re-published patches with same KB name, and it might have already approved
in some month back so no deadline setting will take effect. If this is the case how we can tackle this. Appreciate help on this....

Hi Sankar,
Are these servers stuck into a rebooting loop? If yes, please enter the safe mode, then remove the update in control panel.
>>I have got a info like Microsoft re-published patches with same KB name, and it might have already approved in some month back so no deadline setting will take effect.
Could you please povide the detailed information about this update? I will check if this update has been re-released in my lab.
Normally, even if two updates have the same KB number, the second update will not inherit the approval from the first one. They are two updates.
To prevent the server which has downloaded this update from installing it, please follow the steps below:
Click Start, click Run, type cmd in the
Open box, and then click OK.
At the command prompt, type services.msc.
Right-click Automatic Updates, and then click Stop.
Rename the C:\Windows\SoftwareDistribution\Download folder as follows:
C:\Windows\SoftwareDistribution\Download.old
In the Services snap-in, right-click Automatic Updates, and then click
Start.
Besides, before deploy the update in production environment, it is recommended that test the update in a test group.
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Similar Messages

Virtual servers are rebooting automatically

Hello All,
I am having an issue with Virtual Servers.
I have 5 node cluster. Last week due to storage firmware upgradation we had some problems. after that we contacted storage expert and get it rectified. Now One of cluster node is having a issue. Once i move the VMs (This node is the owner of VMs) then the
virtual servers are automatically rebooting. Now this node is ideal. In addition to that we checked all updates and run the failover test also..every thing is showing green.
Can any one have solution for this, please help me.
Thank you.
Karan

Hi Karan,
Unfortunately, the available information is not enough to have a clear view of the occurred behavior. Could you provide more information about your environment. For example,
the exact text of any error messages that you received that are associated with this problem?
The server version of the problem on, when you experience this issue what are you trying to do, when this problem occurs the system log record information, screenshots is the best information.
The 1146 event just can offer us the cluster fail, but we still need more information, please post your cluster log. You can refer the following article to generate the cluster
log.
How to create the cluster.log in Windows Server 2008 Failover Clustering
http://blogs.msdn.com/b/clustering/archive/2008/09/24/8962934.aspx
If you are using 2008r2 cluster please install the Recommended hotfixes and updates for Windows Server 2008 R2 SP1 Failover Clusters updates then monitor this issue again.
http://support.microsoft.com/kb/2545685
More information:
Event Logs
http://technet.microsoft.com/en-us/library/cc722404.aspx
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

PROD Application servers are reflecting after system refresh in ST03 of QUA

Hi,
We recently performed DB refresh activity from Source: Production to Target: Quality.
We have 6 application servers excluding our central instance in production system.But after the system refresh,we observed in ST03 that these production application servers are reflecting as nodes on the left hand side in Quality system after refresh.
Please help us how to delete those application servers in ST03.
Regards,
Sudheer.

I too face the same problem with our quality system after refresh.

Force software reboots after Software Updates install, and do a WUA rescan upon reboot and install any remaining patches?

Running SCCM 2007 SP2 R3 and having two big issues with SUP that impacted us severely with the February patches. An RDP patch from November broke our 2-factor authentication (2FA) method, so we stopped deployment until Microsoft could fix the
patch. Rather than fixing the patch...they made a patch for the patch.
We divided our servers up into multiple Day/Time maintenance windows, like SUN, MON, TUE, and from 0200 to 0600 AM, and we run deployments weekly as needed.
There doesn't seem to be a way in SUP to "let SCCM control reboot" and ALWAYS reboot (whether the patches request it or not), and, as a result, we seem to have an awful lot of servers that are stuck at "reboot pending" after patch installation,
and have actually taken to using a third-party program to reboot the servers.
There also doesn't seem to be a way to force SCCM SUP to rescan the computer after the patch is applied until after a day...or, for servers, a week (from Mon to Mon, for example).
What happened this time around was that the first patch installed and broke 2FA, the second patch is not recognized as being needed until after a reboot and rescan--since that did not occur, it took up to a week to get the second patch installed (IF the
server ever was rebooted), which...was unacceptable.
Soooo...how can I:
1. ALWAYS force SCCM to reboot after patching (60-min countdown if user logged-on), just like we do with our normal deployment advertisement, package, program.
2. Force a WUA scan after this reboot, so, if remaining patches from this patch group are needed, they get detected and installed, and hopefully this will all work within the 4-hour window (we might be able to extend it earlier,
but, not past 0600).
Thanks!

Thanks, Don. OK, if there is a "reboot required" returned at the end of the patch deployment...shouldn't the computer then reboot? We see a large number of computers with "reboot required" that never reboot. Is there something wrong in
the setup to stop a reboot from occurring?
Thanks.
It looks like you've continued the conversation with Jason and it's taken an interesting turn ;)
But, in the case where a reboot_required is the returned resultcode, CCM will look to your MW and deployment settings, and the context of the installation event (enforcement etc), to determine if the reboot request should be honoured or refused.
You should be able to see all the to-and-fro of this logic within the client logfiles, as it's occurring (or after the event).
If you do some spelunking into the logfiles, don't forget to look at windowsupdate.log (the WUAgent logfile), as that can, with the CCM logfiles, paint a more complete picture of the "flow of things".
This does all assume that the client machine is in a healthy and predictable state to begin with.
If there is already some other pending_reboot hiding in the background, or, WUAgent is running with it's own configuration (potentially fighting with CCM), or, it's Win8 with the "Automatic Maintenance" scheduled task, you can get some unexpected behaviour
(but usually that is unexpected reboot, rather than unexpected no-reboot)
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

Reboot after applying patch 112915-05 realy necessary?

Hi,
I have a short question about the patch 112915-05 which i have to apply to our sol9 servers. The patchdescription tells me to reboot the server after the installation.
But now i woundering about the patch content. Only the file /usr/sbin/snoop will be replaced with this patch. I have downloaded the patch and had a short look into it, there is realy only the snoop binary in the patch. Is this a wrong information in the patch description or is the reboot realy necessary?
Thanks for Help
[http://sunsolve.sun.com/search/document.do?assetkey=112915|http://sunsolve.sun.com/search/document.do?assetkey=112915]
Files Included in this Patch:
/usr/sbin/snoop
Special Install Instructions:
NOTE 1: Perform patch installation in single user mode.
Reboot the system after patch installation.

For patch 119810-05 ( http://sunsolve.sun.com/search/document.do?assetkey=1-21-119810-05-1)
Installation Requirements:NAThis means no reboot required and you don't even have to be in single-user mode to do the install of this patch.
Contrast this with a patch where you MUST be in single-user and MUST reboot after patch installed:
For patch 127111-10 ( http://sunsolve.sun.com/search/document.do?assetkey=1-21-127111-10-1 )
Installation Requirements:Reboot immediately after installing this patch on an active boot environment to bring the system to a consistent state. An alternative may be specified in the Special Install instructions.
Use Single User Mode (run level S) when installing this patch on an active boot environment. An alternative may be specified in the Special Install Instructions..
Special Install Instructions: -----------------------------
NOTE 1: Before installing this patch, please install the latest patch
utilities patches for your OS. This list of patches is defined
at - http://sunsolve.sun.com
Please use the pull down list which appears after the text:
"Latest Patch Update: To ensure the correct functioning of the
patching utilities on your system, stay up to date on the
following patches"
README -- Last modified date: Friday, March 7, 2008

Multiple servers hung on reboot after installing the following April 2014 Updates. Anyone else?

We installed the following updates last night via WSUS. All of our Windows 2012 R2 servers rebooted but then stuck with the swirling logo and never booted back in to Windows. We had to power them off and back on again.
Anyone else find issues with these patches and experience this? This was consistent. We are running Vsphere 5.5 u1.
- Security Update for Windows Server 2012 R2 (KB2922229)
- Update for Windows Server 2012 R2 (KB2939087)
- Windows Malicious Software Removal Tool for Windows 8, 8.1 and Windows Server 2012, 2012 R2 x64 Edition - April 2014 (KB890830)
- Rules Update for RRAS Best Practice Analyzer for Windows Server 2012 R2 (KB2928193)
- Security Update for Internet Explorer 11 for Windows Server 2012 R2 (KB2936068)

Hi,
Thank you for posting in Windows Server Forum.
I am trying to involve someone familiar with this topic to further look at this issue. There might be some time delay. Appreciate your patience.
Regards.
Vivian Wang
Hello and thank you. I was able to narrow this down to KB2939087 and reproduce.
Only our IIS servers, and domain controllers had the problem. Vanilla 2012 R2 servers did not hang on boot up.
We installed VIA WSUS and the servers automatically rebooted OK and installed OK but upon boot up they got stuck at the swirling logo and stayed their indefinately until we hard reset them and powered them back up. There no nothing in the event whatsoever
to indicate a problem.
Kind of a big deal to have to babysit all of these servers and hard reset them after installing this update via WSUS.

Client machine force reboot after apply window patch updated

I found all of client machines will force reboot after window patching updated via SCCM 2012. Have any options in SCCM 2012 can let users to choose reboot their machine after patching ? likely WSUS, users can suspend the reboot request. Pls advice.

The notification will happen automatically if ConfigMgr installs updates that require a reboot but a reboot is not initiated so there's nothing additional you need to do.
Note however that allowing users to choose this instead of forcing it is generally bad practice because the updates aren't truly installed until the reboot happens and there have been a couple of updates of the years that cause flakiness until the system
is rebooted also.
Why not allow the users to install the updates when they want up until a deadline and then force the reboot at the deadline (if one hasn't already been performed)? This gives the user the control over the process but also forces it to happen if the user
neglects performing it.
Jason | http://blog.configmgrftw.com

Mail outgoing servers say they are disconnected - after an update was installed

When I updated to Mavericks I had this problem with Gmail and a Yahoo account. I can receive e-mail, but not send. It tells me the outgoing servers are disconnected. Now the problem is back after an update. I tried the 995 and 465 ports - does not work.

Hello slesage,
Thanks for using Apple Support Communities.
To troubleshoot issues with Mail on your Mac please follow the steps in the article below.
OS X Mail: Troubleshooting sending and receiving email messages
http://support.apple.com/kb/TS3276
Take care,
Alex H.

System Panic After Patch by using EIS

Hi,
My system go panic when I rebooted my V100 after patch it with EIS Jan 2007 version. The error show below :
panic[cpu0]/thread=30000f4dca0: BAD TRAP: type=31 rp=2a1002ff340 addr=38 mmu_fsr=0 occurred in module "genunix" due to a NULL pointer deferenceied to the system
I had search through many similar case but i couldn't get a solution for this. Please help.

The latest README for the Solaris 10 Recommended patch cluster, details complications for patch 118833-36. Lots of people are running into problems.
If you are going to try to jumbo patch again, check the special instructions:
Single-user mode, do not use the "-nosave" option, and patch a second time immediately afterwards, again in single-user mode.

IPhone 6Plus on every reboot after putting in my password it opens to a small window asking for apple id password

everything works on phone and wow it's big compared to my iPhone 5s. went with space grey since i have had 3 white phones in a row. restored via iCloud backup. updated iTunes as i have about 3,000 songs. 250 bought the rest ripped to AAC from my cc's....what a pain but switched from my windows desktop to this new rMBP late 2013 for xmas and iTunes is slightly different on a mac than windows and where everything is stored on drive.
anyhow problem is every time i reboot after putting in my password and arriving at whatever page i left at i get a very small window asking for my Apple id password. Now the top half is pre filled in with the email address i use for iCloud/itunes/apple/etc.
i did see in settings there is a checkmark i cannot remove that says for apple password "ask immediately" there are no other choices. it can't be unchecked by any method i found.
any help appreciated.

In case anyone else gets this I hit cancel once and it has never come back.

Function module "GM_DOCUMENT_REVERSE" not found. after Patch Update

Hi Abapers/Basis
After patch update i am not able to do FBCJ reversal entry getting below error message.
Runtime Errors         CALL_FUNCTION_NOT_FOUND
Exception              CX_SY_DYN_CALL_ILLEGAL_FUNC
Date and Time          25.05.2011 14:43:26
Short text
     Function module "GM_DOCUMENT_REVERSE" not found.
What happened?
     The function module "GM_DOCUMENT_REVERSE" is called,
     but cannot be found in the library.
     Error in the ABAP Application Program
     The current ABAP program "SAPLRWCL" had to be terminated because it has
     come across a statement that unfortunately cannot be executed.
What can you do?
     Note down which actions and inputs caused the error.
     To process the problem further, contact you SAP system
     administrator.
     Using Transaction ST22 for ABAP Dump Analysis, you can look
     at and manage termination messages, and you can also
Error analysis
    An exception occurred that is explained in detail below.
    The exception, which is assigned to class 'CX_SY_DYN_CALL_ILLEGAL_FUNC', was
     not caught in
    procedure "CALL_DISPATCHER_STORNO_R" "(FORM)", nor was it propagated by a
     RAISING clause.
    Since the caller of the procedure could not have anticipated that the
    exception would occur, the current program is terminated.
    The reason for the exception is:
    The program "SAPLRWCL" contains the CALL FUNCTION statement.
    The name of the function module to be called is "GM_DOCUMENT_REVERSE".
    No function module exists with the name "GM_DOCUMENT_REVERSE".
    All function modules are listed in the Function Library (SE37).
    Possible reasons:
    a) Wrong name specified. Pay particular attention to
       upper/lower case and underscores ("_").
       or
    b) Transport error
    c) In the case of an enqueue/dequeue module,
       the lock object may not have been activated
       (ABAP/4 Dictionary).
How to correct the error
    Check the last transports to the SAP System.
    Is the program "SAPLRWCL" currently being changed?
    If an enqueue/dequeue module is involved, is the activation
    of the lock object missing in the ABAP/4 Dictionary?
    If the error occures in a non-modified SAP program, you may be able to
    find an interim solution in an SAP Note.
    If you have access to SAP Notes, carry out a search with the following
    keywords:
    "CALL_FUNCTION_NOT_FOUND" "CX_SY_DYN_CALL_ILLEGAL_FUNC"
    "SAPLRWCL" or "LRWCLF10"
    "CALL_DISPATCHER_STORNO_R"
    Function modules with names similar to "GM_DOCUMENT_REVERSE":
    GM_DOCUMENT_CLOSE
    GM_DOCUMENT_RECORD
    GM_DOCUMENT_DELETE
    GM_DOCUMENT_POST
    GM_DOCUMENT_CHECK
    G_DOCUMENT_RECORD
    GJ_DOCUMENT_RECORD
    GM_DOCUMENT_PROJECT
    GET_DOCUMENTS
    GM_DOCUMENT_DISPLAY
    If you cannot solve the problem yourself and want to send an error
    notification to SAP, include the following information:
If you cannot solve the problem yourself and want to send an error
notification to SAP, include the following information:
1. The description of the current problem (short dump)
   To save the description, choose "System->List->Save->Local File
(Unconverted)".
2. Corresponding system log
   Display the system log by calling transaction SM21.
   Restrict the time interval to 10 minutes before and five minutes
after the short dump. Then choose "System->List->Save->Local File
(Unconverted)".
3. If the problem occurs in a problem of your own or a modified SAP
program: The source code of the program
   In the editor, choose "Utilities->More
Utilities->Upload/Download->Download".
Moderator message: please don't just dump your dumps, search for SAP notes or open a call with SAP instead.
Edited by: Thomas Zloch on May 25, 2011 2:16 PM

Hi Karthik,
Thank you for ur reply.
I did not implement any user exit/ badi. Dump is saying that my smarform function module does not exist in the se37 library.
I have excuted my form through se38, that time is working fine. When i tried through output type it is going to dump.
Regards,
Kusuma.

Authorization problems after patch 6 upgrade and re-install

Hello everybody.
I had a perfect working Visual Composer installation.
After patching it, I got an 401 message, stating that I do not have authorization to view this page:
HTTP Error 401.1 - Unauthorized: Access is denied due to invalid credentials.
Uninstalling and reinstalling didn't bring me much further. It seems to be an Internet Explorer and/or IIS 6.0 related problem.
Of course I followed the very valuable note 804996, but the problem remains...
Can anyone help me out?
Thanx.

Hi all.
I resolved my own problem.
Additional to the permission settings as they are explained in note 804996, you must add the Directory Security - Authentication & Access Control, set to Integrated Windows Authentication.
Otherwise Windows NTFS security will block you.
Gr.,
Marc.

Fix for continuous reboot after installing Service Pack 3 in Windows XP

After contacting HP Technical Support and speaking to a supervisor we were able to solve the problem of Windows continuously rebooting after installing SP3. Here are the steps that fixed the problem with my HP Pavilion running on an AMD processor. The steps are actually fairly straight forward and easy....
Issue: The computer reboots continuously after installing Windows XP service pack 3
Computer reboots continuously after installing Windows XP service pack 3 on AMD systems. The problem is that with some configurations, SP3 causes the computer to crash during boot, and Windows XP, by default, is set up to automatically reboot when it crashes. That is why you end up in the endless rebooting scenario.
Cause:
On HP computers, the same Windows installation disc image for Intel processor based PC's is deployed for the AMD processor based computers as well. Because the original installation image for both Intel and AMD is the same, all have the intelppm.sys driver installed and running. That driver provides power management on Intel-based computers. On an AMD-based computer, amdk8.sys provides the same functionality for power management.
Symptoms:
Ordinarily, having intelppm.sys running on an AMD-based computer appears to cause no problems. However, on the first reboot after a Service Pack 3 installation, it causes a big problem. The computer either fails to boot, or crashes with a STOP error code of 0x0000007e.
You may not see the error code because the computer reboots too fast. In order to get the error message, you need to set an option during startup. To do so, open the windows advanced menu by tapping the f8 key on startup. Then select the "Disable automatic restart on system failure" option.
Solution:
If you have an AMD-based computer, however, you do not need the intelppm.sys driver and can disable it. There are three methods in order to do this.
Step 1: Please try to log on the system in safe mode.
1. While using Safe mode open the command prompt.... Start, All Programs, Accessories, Command Prompt
Run the following command in the command prompt just like it's typed: sc config intelppm start= disabled
Step 2:
If the issue persists, please try to log on or boot the system in recovery console (refer to the web document)
2. Using recovery console:
If you booted into the recovery console, from a command prompt, type: disable intelppm
Step 3: Please check in registry.
3. Using windows registry:
1. Run regedit
2. Click on HKEY_LOCAL_MACHINE
3. From the File menu, select "Load hive"
4. Navigate to %systemdriver%\Windows\System32\Config on the dead system and select the file name System
5. Name it something you can remember, such as "horked"
6. Navigate to horked\ControlSet001\Services\IntelPPM
7. Double click the Start value and set it to 4
8. If you did what I did and completely messed things up by running a disk check previously, navigate to ControlSet001\Control\SessionManager. Open the BootExecute value and clear out the autochk entries.
9. Repeat steps 6-8 for the other control sets.
10. Reboot
Reference:
http://support.microsoft.com/kb/888372
Additional information:
Computer Restarts after Displaying Stop Error 0x0000007E (After Updating with Service Pack 3 for Windows XP):
http://h10025.www1.hp.com/ewfrf/wc/genericDocument?docname=c01457284&cc=us&dlc=en&lc=en&jumpid=reg_R1002_USEN
For future reference: Service pack 3 Installation steps:
Before installing the service pack 3 update, please follow the steps listed above and save yourself much time and effort.
To uninstall service pack 3, I suggest that you uninstall it from add/remove programs.
Step 1:
Uninstall service pack 3 from add/remove programs:
1. Click Start.
2. Select Run.
3. Type appwiz.cpl in the run field.
4. Click OK.
5. Click change or remove programs.
6. Select the program -service pack 3 that you want to uninstall or remove.
7. Click Remove button.
8. It will pop up the message stating that "Are you sure you want to remove the programs".
9. Click Yes. It will help you to remove or uninstall the installed programs from add and remove programs.
Step 2: If the issue persists, I suggest you to perform system restore and then try to install the service pack 3 after performing the steps mentioned above in regards to removing the intelppm.sys Driver.
Using Microsoft System Restore in Windows Me and XP:
http://h10025.www1.hp.com/ewfrf/wc/genericDocument?docname=bph07103&cc=us&dlc=en&lc=en&jumpid=reg_R1002_USEN
Step 3:
How to obtain the latest Windows XP service pack :
http://support.microsoft.com/kb/322389/
Steps to take before you install Windows XP Service Pack 3:
http://support.microsoft.com/kb/950717/en-us
I hope this helps someone who is having this problem. It sure took me a minute to get it all figured out. :0)

Still useful as of 12/30/11. Have ten Lenovo 5042 computers with downgrade licenses to run XP and have a ghosted image from another Lenovo 5042 having and Intel cpu. My target computers all have AMD cpus in them and the image would continuously reboot on
the AMD computers.
Used method 1 and it cleared the problem instantly, many thanks for the post and the time and effort it took to dig up the answer..

Sales office data missing after patching in CRM

Hi,
We have CRM 4.0 for internet sales.
Recently, we patched our Development and QA CRM systems from SAPKU40009 to
SAPKU40016.
Immediately after the patching, we see that the Sales office information in the BP (Sales area- organization tab) is missing. We have only one Sales org and Dist channel with division not active. All the sales office belong to the same sales org. Nothing has changed w.r.t org model before and after patching and all the org units are checked for determintation.
Everything was working before the patching. Just after patching, we find the sales office information blanked out in the BP and as well as the drop down list is empty.
I can see the sales office table entries for all the BPs in CRMM_BUT_SET0140. But when ichange the BP data (for some other field) and save, the table entries get deleted as i am not able to assign the sales office any more.
We have not buffered the attributes. I tried that also and ran the report HRBCI_ATTRIBUTES_BUFFER_UPDATE, but it is of no use.
Can somebody help?
Thanks
Shankar

Hi ,
What you can do is,
Create a request for a material whose Sales Area data is missing in
CRM , and perform the request load in transaction:R3AR4.
And please check whether sales area data flows to CRM.
Put a filter in txn:R3AC1, to download single material or material
range.And before performing an initial load in txn:R3AS,please make
sure that sales area data is missing in CRM.Now, perform the initial
load in txn:R3AS.And please check whether sales area data flows to
CRM.
Check the filter settings in transaction R3AC1 for
object MATERIAL and please make sure that it would bring down all
the expected materials from R/3 along with the sales area data. I guess there is some
filter setting which is blocking it.
Please check the entries you have maintained in table MVKE - the entries
for the sales data maintained here must match with the ones maintained in the
filters.
thanks & regards,
Krishnen
Edited by: Krishnen Subramanian on Aug 9, 2011 8:47 AM

Text messages and phone calls from March 2012 to date are missing after activating iphone5

text messages and phone calls from March 2012 to date are missing after activating iphone5. I backed up my 4 before activating my 5. Can i retrieve them somehow?

i would not want to bet on nokia ever releasing a patch or update in the software to allow this function on this particular phone.
if you look at nokia phones over the years, they have added functionality like this across a wide range all at once, take for example timed profiles on symbian phones. these have only just been phased in.
i do not think it is a development cop out, more along the lines that nokia is a huge company and as such would have a huge effor in market research. if they didnt pick this out through their market researc, why spend the money adding it?
the comment on annoyance is entirely personal to me, as it is important to you - you may want to consider moving to a symbian (series 60) based handset as these give you a lot of expansion for this sort of need.

Servers are rebooting after patch syncronization

Similar Messages

Maybe you are looking for