Setting up NICs and Volumes on VMware

Virtual NW 6.5.8/BM 3.8.5 on VMware 4.1. The only TID I found was for
setting up BM on VMware 2.5.
1. In the VM Configuration tab, the VM Network shows vmnic0, which is
used to access the VM machine through vSphere, and vmnic1, which is
Down. Both adapters are in or associated with vSwitch0.
In the BM virtual machine, I added the second adapter, but I'm not sure
if that is correct or whether two additional virtual adapters need to be
created/used.
2. When installing BM, I created two cache volumes. However, they are
listed in iManager as one traditional partition. Is this a problem?
Even if not, the free space is not considered a pool (the only pool
listed is SYS), but rather as two free space partitions, which I cannot
seem to be able to use for two volumes I want to create.
Any help with either issue will be greatly appreciated.

On 8/26/2010 11:14 AM, Jack Cunha wrote:
> Virtual NW 6.5.8/BM 3.8.5 on VMware 4.1. The only TID I found was for
> setting up BM on VMware 2.5.
>
> 1. In the VM Configuration tab, the VM Network shows vmnic0, which is
> used to access the VM machine through vSphere, and vmnic1, which is
> Down. Both adapters are in or associated with vSwitch0.
>
> In the BM virtual machine, I added the second adapter, but I'm not sure
> if that is correct or whether two additional virtual adapters need to be
> created/used.
>
> 2. When installing BM, I created two cache volumes. However, they are
> listed in iManager as one traditional partition. Is this a problem? Even
> if not, the free space is not considered a pool (the only pool listed is
> SYS), but rather as two free space partitions, which I cannot seem to be
> able to use for two volumes I want to create.
>
> Any help with either issue will be greatly appreciated.
To be clear, the two cache "volumes" are not listed as Volumes in
iManager, only as a single partition.

Similar Messages

Update weight and volume when changing the quantity

Hello ALL,
For some configurable items, those whose weight and volume depends on configuration, when changing the quantity at set level, weights and volumes are not calculated again and order item is saved with wrong data about weights and volume.
when ever changing the quantity we will get a message - " Changing date/quantity may result in different BOM Please configure"
if we do explicitly by clicking "Item Details Configuration' then Weight and Volume will get update automatically.
my requirement is Weight and volume should get update automatically when changing the quantity with clicking on "Item Details Configuration'.
could you provide any OSS notes available for this or any help to achieve this functionality.

Dear Prathap Naidu P,
Did you solve this issue?
Because I have the same problem, and I was looking for hints.
Thank you so much for any help.
Best regards,
J.Flanders

I have a number of apps on my Ipad2 that no longer have sound. I have checked setting on my ipad and the settings on the apps that have a settings and the sound and volume are ok. Do I have a virus in some apps?

I have a number of apps on my ipad2 tha no longer have sound. I have checked the ipad settings and the apps that have settings and all sound and volume are ok. Do I have a virus? Pandora sound is ok. It seems mostly to be games...angry birds, tap tap, and educational games for little ones. Any suggestions?

There aren't any viruses for iOS devices. Have you got notifications muted ? Only notifications (including games) get muted, so the iPod and Videos apps, and headphones, still get sound.
Depending on what you've got Settings > General > Use Side Switch To set to (mute or rotation lock), then you can mute notifications by the switch on the right hand side of the iPad, or via the taskbar : double-click the home button; slide from the left; and it's the icon far left; press home again to exit the taskbar. The function that isn't on the side switch is set via the taskbar instead : http://support.apple.com/kb/HT4085

I just got an iphone 4 yesterday. I got everything all set up and working great. When I woke up last this morning, my ipod has no sound and the albums covers are all mixed up. I've checked all my settings and volume control. My text sound won't work eithe

I just got an iphone 4 yesterday. I got everything all set up and working great. When I woke up last this morning, my ipod has no sound and the albums covers are all mixed up. I've checked all my settings and volume control. My text sound won't work either. However, my ringtone works just fine.

Have you taken the steps recommended in the User Guide: restart, reset, restore?

My iMac makes a beep tone every minute. This persists even though volumes set to zero and notifications have been set to Do Not Disturb.

My iMac makes a beep tone every minute. This persists even though volumes set to zero and notifications have been set to Do Not Disturb.

It's likely that one of your login items is causing the problem. Select the Login Items tab in the Users & Groups pane of System Preferences. Delete any items that you don't recognize.

How to preserve pan and volume setting?

I make changes to the pan and volume controls, but lose them whenever I restart the song. Is there a way to preserve these?
TIA
Olushola

I don't think so. I may have accidently done so. I have to read up on automation.
Olushola

I set a code for volume limit and forgot what it was....wat do i do?

help me

To reset the code, you will need to select the iPod in iTunes and click Restore.
This will erase the iPod and restore the iPod OS (and remove the screen lock and volume lock codes).

How to set up set which NIC card to use for multicast?..

 I just downloaded Rolling Patch 1 for WLS6.0SP2.
 While reading the README file it says
 " ISSUE 42518: Provided a way to set which NIC card to use for multicast traffic
 Can anyone tell me how to set this?. on my WebApplication server it has two NIC
 cards and I want to use the NICcard which is being used to talk to internal network
 for multicast messages.
 One more thing,
 Can anyone one tell how to search for bugs (ISSUES) in weblogic. I am looking
 place where I enter ISSUE number and should get the detailed description of bug/issue
 etc..
 Thanks for helping,
 Nilesh


 Thanks Kumar, I'll try this.
 Does this -Dweblogic.interfaceAddress used only for multicast. Or this is also
 used to talk to AdminServer?.
 The other problem I am facing is when I restart the AdminServer in recovery mode
 it's not finding my WebApp servers, because my webapp servers are on public network
 and my admin (management) server is on private network.
 please look at http://newsgroups.bea.com/cgi-bin/dnewsweb?cmd=article&group=weblogic.developer.interest.management&item=1217&utag=
 , for more details about my problem.
 Thanks,
 Nilesh
 Kumar Allamraju <[email protected]> wrote:
 ><!doctype html public "-//w3c//dtd html 4.0 transitional//en">
 ><html>
 >You should be able to do it via console in 6.1
 > Not sure if it was added in 6.0
 >For 6.0 you can set this via command line
 > java -Dweblogic.interfaceAddress=<addr>
 >You need 6.0 SP2 RP1
 >--
 > Kumar
 >Nilesh Shah wrote:
 ><blockquote TYPE=CITE>I just downloaded Rolling Patch 1 for WLS6.0SP2.
 > While reading the README file it says
 > " ISSUE 42518: Provided a way to set which NIC card to use for multicast
 >traffic
 > "..
 >Can anyone tell me how to set this?. on my WebApplication server it
 >has two NIC
 > cards and I want to use the NICcard which is being used to talk to
 >internal network
 > for multicast messages.
 >One more thing,
 >Can anyone one tell how to search for bugs (ISSUES) in weblogic. I
 >am
 >looking
 > place where I enter ISSUE number and should get the detailed description
 >of bug/issue
 > etc..
 >Thanks for helping,
 >Nilesh</blockquote>
 ></html>
 >

I have two time capsules (1TB, 2TB) and want to use one for another set of Macs (my Family). How do I set both up and keep all the Macs from joining both Time Capsules?

I Have two Time Capsules (1TB and 2TB) and want to set one for business and the other for family - networking seperate Macs to each.

Both should be plugged into the network with ethernet.. if at all possible.
If you have a router already then both bridged otherwise one set to router and one to bridge.
How do you access the TC? Ethernet or wireless?
Are they located in the same area?
You could set different wireless networks.. if they use wireless.. this is nice easy way to do it.
You can set user account in the TC you want the business one to join with.. that will prevent access by the family.
So there is a number of ways.. none are particularly secure btw.. the TC is a home not a business device.. if anybody wants access they press the reset for one second.. pofff all the passwords are default for 5min.. to allow people who forget their password to get access.
On ML you can encrypt TM backups.. this is better for security if that is the problem.. and still use different user profile to prevent access.

The ringer of my iphone 4s is not working but when itried to go in setting then sound and tried to change ringtone the ringer is working..pls help

the ringer of my iphone 4s is not working but when itried to go in setting then sound and tried to change ringtone the ringer is working..pls help

Check the mute switch along the side, near the external volume controls.

Setting up gateway and firewall in OS X Server 10.3?

Hi all,
I have a G4 tower with two working ethernet cards in it that I would like to configure as a gateway and firewall. It has OS X Server 10.3 on it. I have easily found the firewall configuration in the Server Admin intrerface, but I can find nothing about configuring the server to act as a gateway. The only information I have found that is pertinent is related to the Gateway Setup Assistant that comes with OS X Server 10.4, which doesn't exaclty help me. Does anyone have any documentation on configuring OS X Server 10.3 to be a gateway? Thanks.

Actually, I may have marked this as answered too quickly...
So I followed the guide at the back of the getting started manual, and set everything up as follows:
- PCI ethernet card is set up as the connection to the outside world. It is plugged into a switch which connects to a wall jack. In Network under System Preferences, it is set up as the first internet conection to try. It has a static IP address, and is set up to use the organization's DNS servers. It is NOT plugged into the upstream port, but is instead in port #9. The light on the router is on.
- Built-in wireless is set up to be the internal connection. It is plugged into the upstream slot on anouther switch. It has a static IP address, and is set up to use the organization's DNS servers. The light on the router is on, so it appears there is a connection.
- A different computer is plugged into the second switch, which a static IP address and to use the organization's DNS servers.
So basically, unlike in the scenario in the manual, I am not using the OS X Server for DNS, DHCP or NAT services. That should, if anything, simplify it.
The firewall service is started, and is set to allow all traffic in and out, no problems. Nice and simple to start.
The server has an okay connection to the outside world via the PCI ethernet card. I can ping other machines and load web pages. I cannot, however, access the machine connected to the router which is connected to the built-in ethernet. Likewise, that machine has no access to either the OS X Server or the outsideworld.
How does OS X Server decide which ethernet card is to be connected to the outside world, and which is for the internal firewall? Is the confusion possible because I'm connected to two routers?

Setting Up WSE and DC AFTER Installing 2012 R2 Standard

I am purchasing new hardware for my WSE 2012 R2 server that I will need to configure BEFORE installing WSE. One example is NIC Teaming, the new box has 4 NICs and I want to team them for redundancy and speed. I cannot set up teaming until the OS is in place
(unless there is a way of doing so during WSE Setup). Another is setting up the file space of 4 drives as a RAID 5 Array.
Is it possible to install WSE on an already configured 2012 R2 Standard box and promote it after I have accomplished these tasks?
Thanks,
Bob Hessenauer

Hi BobHessenauer,
Could clarify your question? I am not quite understand your question “and promote it after I have accomplished these tasks?”, do not use NIC teaming, if you want to improve
the deploy speed you can use multicast.
More information:
Windows Deployment Services Getting Started Guide for Windows Server 2012
http://technet.microsoft.com/en-us/library/jj648426.aspx
WDS Multicast Server
http://technet.microsoft.com/en-us/library/cc726564(v=ws.10).aspx
Windows Server 2012: Master Windows Deployment Services
http://technet.microsoft.com/en-us/magazine/dn163597.aspx
How Do I: Use Multicast Transmission to Deploy Multiple Clients
http://technet.microsoft.com/en-us/video/how-do-i-use-multicast-transmission-to-deploy-multiple-clients.aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Why do i get a camera icon and volume bar on my lock screen now that i have updated to ios 5

Why do i get a camera icon (bottom right)and volume/buffer bar (top centre) of lock screen....only happening since ios5 update..

It's a feature of iOS5. If you double tab the home button, you can use the camera or play music without having to enter your lock code. If you single tap the home button, you should just see the lock screen. It's nice if you want to take a picture quickly.

2012 R2 Hyper-V Cluster two node design with abundance 1Gbps NICs and FC storage

Hello All,
First post so please be gentle!
We are currently in the process of building/testing the upgrade of two node 2012 R2 Hyper-V cluster.
Two hosts built with Datacentre 2012 R2 which will host approx. 30 VM's.
Shared storage will be fault tolerant FC- connection.
10, (yes 10!) 1Gbps NICs are available, Intel i350.
trying to decide on teaming interfaces using native LBFO and the 2008 'style' of using un-converged networking, or teaming up most interfaces and using QoS. Can find many/numerous examples of using 10Gbps NICs and converged, however 10Gbps networking
isn't an option right now.
recommendations appreciated.
thanks

Hi Sir,
>>trying to decide on teaming interfaces using native LBFO and the 2008 'style' of using un-converged networking, or teaming up most interfaces and using QoS.
The following link detailed the teaming configuration and it's applicable scenario (server 2012):
http://www.aidanfinn.com/?p=14039
Also please refer to the document for 2012R2 LBFO :
http://www.microsoft.com/en-us/download/details.aspx?id=40319
In server 2012R2 , there is a new setting "Dynamic" for "load banacing mode " and it is recommended to use Dynamic for "Load banacing mode" :
If you can accept 1GB max bandwidth for each VM I would suggest you to use LBFO mode : Independent/dynamic/None(All adapter active) .
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

I did re-set my password and when I click on Install for Mavericks, I still get a box for "administrator password" and it still won't accept my new password. Is there a difference between my Apple ID and the administrator password they're asking for?

I downloaded Mavericks and it won't install. I did re-set my password and when I click on Install for Mavericks, I still get a box for "administrator password" and it still won't accept my new password. Is there a difference between my Apple ID and the administrator password they're asking for? I never had an administrator password-- I just hit enter and have never had a problem before with previous installations. I'm on an iMac, from 2007, running Mt. Lion (version 10.8.5). I've been looking for other's posts who may be having the same problem, but haven't found any. Can anyone help?

Ugh. The 'no password, no work' thing is a recent Apple development. I ran into it on my system and ended up having to do a clean install on a partition I fully erased.
I suppose, if you have the ability to, go online and look up how to burn a bootable DVD image. Download the 10.8.4 image then use the Disk Utility to make a boot image of it. You'll need a dual-layer DVD or a USB drive (or memory stick at least 8GB) If you've got an optical drive, burn the disk, if you've a USB device, use that.
Then get a pocket drive and copy your important files off the system or let Time Machine do a full backup.
When the backup is done, insert the disk and hold down the C key until the machine boots off of the DVD. At the point you get to the start window, go to the menu and choose the Disk Utility.
In the Disk Utility, reformat the drive. You go to the actual DRIVE (not the Macintosh HD, but the root above it that is the actual hard drive device)
I always do this and *partition* it into several volumes, the benefit being, you can store all of your music, documents and importans stuff on that secondary storage volume you make - it will have it's own index and then the first volume is where you put the OS and it will have it's own index as well. That way, if the OS throws a wobbler and you need to reinstall, you don't lose your data.
Depending on the size of your hard drive, it is good to give your OS partition at least 60GB and optimally 100GB, and the rest for storage.
Name your volumes, use the little box sliders to manually size them or put that number in the size window, select for the format, Mac OS Extended (Journaled) and hit Apply and then the Disk Utility will quickly create your new partitions.
Once finished, quit the Utility and it will return you to the OS installer. Select the volume you want to install to and it should start up and install.
Once the installation is done, you'll get the new machine startup then you MUST put in a password for the computer. Once you're in, and to the desktop, don't bother with any Mountain Lion updates, go right to the App Store and get the Mavericks update and let it install the app to your Applicaitons folder, then do that install.
On a side note, there MAY be a way to make a disk image from the Mavericks application and avoid the entire Mountain Lion step.. I honestly do not know, but a bit of hitting the search engines may find out if there is. I think that if you looked for "make Mavericks boot disk or boot image' you may find something.
Good luck!

Setting up NICs and Volumes on VMware

Similar Messages

Maybe you are looking for