Setup of ASCP centralized

Been A DBA for a while but new to EBS and R12. We have R12 that was built as and OBA. We need to configure/setup ASCP centralized. I've found several documents on setting up ASCP decentralized but not the steps to set up centralized. Does anyone have the steps to configure the setup of a centralized ASCP config?
-TRR

The only difference is that when you are setting up the ASCP instance (ASCP administrator > instances), you don't have to enter db_link information.
Everything else should be same.
Hope this answers your question,
Sandeep Gandhi

Similar Messages

Best practice to setup media server/central location for Itunes, Iphoto

Hey guys,
I currently have a Airport Extreme w/ two Western Digital My Books connected that have my Iphoto and Itunes Library.
This is not ideal since copying things over the network is extremely slow and accessing the media(especially photo librarys) is super janky and leads to disconnects often.
I am looking to revamp my setup. What do you guys recommend?

Should I just get a Mac Mini and connect it to the Airport Extreme?

SAP TDMS add on setup on central/control , sender and reciever systems

I found that SAP TDMS is shipped in the following add-ons:
DMIS: Contains general functions, for example for the process monitor and for the technical data transfer
DMIS_CNT: Contains TDMS-specific functions and some of the process types
DMIS_EXT: For various additional process types (reduction scenarios) for SAP TDMS; currently, it contains only the process type for business process library
DMIS_BSC: For the process types to be used with SAP BI or CRM systems
DMIS_HR: For the process types to be used in the context of SAP Human Capital Management (HCM)
I have read TDMS master guide under section 3.4.1 Setting up the TDMS Server. There is a reference to SAP Note 970531 which is for DIMS setup and there is also reference to SAP note 970532 which is for DMIS_CNT setup.
I would like to know if DMIS_EXT,DMIS_BSC and DMIS_HR need to be setup on TDMS central/control server , sender and reciever or only need to be setup on central/control server for respective scenario realization.
Best Regards
Mohammed Ashraf

All the add-on components need to be installed in all the system (sender, receiver, central, control) in the landscape.

ASCP Instance Setup

Hi,
I am in a position to do Setups for ASCP instance
Environment : Decentralized Environment
Number of Organization : One
I did Database Link properly and Attached the current Organization in the Organizations in the (N) Admin>Instances.
Further when I launch the Data collection process (Complete Refresh), it ends with Phase = Inactive; Status=No Manager error.
How to activate the manager in ASCP instance?
And Please suggest me what are all the other Initial setups I need to do.
Your Answer will be most appreciable.
Regards,
Ramesh

Dear Sandeep,
Thank you very much,
When I checked the "Standard Manager" in the System Administrator Responsibility, It was not Activated.
I tried to activate but It doesn't activated, then that was activated by DBA level.. Then Standard Manager is working fine now.
But After this,
When I launched "Planning ODS Load", this set is launching the concurrent program "Generate Items and Category Sets Keys".
The concurrent "Generate Items and Category Sets Keys" completed with the below Error.
ORACLE error 1400 in FDPSTP
Cause: FDPSTP failed due to ORA-01400: cannot insert NULL into ("MSC"."MSC_ITEMS"."ITEM_NAME")
ORA-06512: at "APPS.MSC_CL_ITEM_ODS_LOAD", line 1955
ORA-06512: at "APPS.MSC_CL_COLLECTION", line 6853
ORA-06512: at line 1
The
Start of log messages from FND_FILE
28-DEC 12:10:47 : ========================================
28-DEC 12:10:47 : Error in PROCEDURE=GENERATE_ITEM_KEYS, TABLE=MSC_ITEMS
28-DEC 12:10:47 : COLUMN=ITEM_NAME, VALUE=
28-DEC 12:10:47 : ORA-01400: cannot insert NULL into ("MSC"."MSC_ITEMS"."ITEM_NAME")
28-DEC 12:10:47 : ORA-01400: cannot insert NULL into ("MSC"."MSC_ITEMS"."ITEM_NAME")
What setup I need to do?
For your information, I launched "Create Planning flexfields" in source Instance. But this Issue is not yet resolved
Your answer will be most appreciable
Regards,
Ramesh

All Mac network setup?

Hello all!
This is my first post here. Thanks for taking the time to help me with an answer to my question below.
I work for a small graphic design firm. We all work on iMacs here in our office (6 Macs total) with the exception of two PCs (1 for receptionist, 1 for data backup), and after a recent virus (Cryptolocker) hit one of our networked PCs, we're looking at going "all Mac" with our setup (if it's possible). I am here to ask for hardware/setup recommendations.
We have just a few needs as we plan our new network setup:
1) A central file repository with at least 4 - 5 TB of storage space for shared files, which all 6 Mac computers must have access to;
2) It has to be a wired network (for fastest file transfer speeds & security -- we already have tons of Cat5 cable installed);
3) A way to backup the central repository to a Cloud service automatically on a nightly basis.
We looked at a Time Capsule, but they max out at 3 TB and we weren't sure if 1) we could daisy chain multiples, and 2) whether they can be backed up to cloud storage in any way.
I am wide open to suggestions on what we need to buy in order to set up the kind of network that we need. I am a Mac convert, so I don't know all there is to know about networking Macs either, so treat me like a 10 year old kid when it comes to explaining/outlining what gear you think we should buy, what hooks up to what, and the system/hardware settings we may need.
I appreciate the time that any of you are willing to take to outline this for me. Thank you in advance for sharing your expertise!

Tesserax,
I have purchased a Western Digital My Cloud 2TB. Need Simple Step by Step guide for Optimal Apple Eco Setup, Sync, Organize, Maintain and Secure my media while freeing storage space on all devices, and maintaining anywhere accessibilty.
Western Digital has setup the drive on the network and it is recognized by iTunes, but they do not want me to move the libraries. iPhoto can import the My Cloud media into its library. They suggest copy'n'paste all media into the My Cloud public folders of Video, Photos and Music then delete the media from the devices. I dont see how you can Sync the iPhones, (future iPads), without moving the libraries, after all the object is to free space on the devices including the MacBooks.
How do I include the My Cloud into the MacBook Pro's Mountain Lion 10.8.5 TimeMachine Backup? (Leave MacBook Leopard 10.5.8 TimeMachine Backup for laptop only)
I have:
2 Users that want to keep their media in separate folders, but would be nice to have a choice between joint or separate viewing ability
MacBook Leopard 10.5.8
MacBook Pro Mountain Lion 10.8.5
2 iPhone 4 - 32GB
Apple TV 2
Time Capsule 2TB (TimeMachine Backups only)
Western Digital (Media Only - perhaps some documents)

Forecast consumption against CTO item in ASCP

In source side module (OM, MRP) , following is the observation:
i) we define a forecast set with consume check box checked for ATO model
ii) create a sales order for ATO model , configure it .
The sales order quantity for configured item is consumed against forecast of ATO model.
I want to do same type(as source) of consumption in ASCP for configured item. Is this possible? I was trying to check this scenario in R12. Following is the setup:
i) created forecast set with consume check box Unchecked for ATO model
ii) create sales order for ATO model and configure it .
iii) run collection
iv) define plan with plan options ;
consume by forecast bucket checked and explode forecast check box checked.
In this above setup, the sales order quantity for configured item is not getting consumed against forecast of ATO model. Is there any thing wrong in setup ? please let me know.

Abhishek,
I would revisit this part of your setup for ASCP:
"created forecast set with consume check box Unchecked for ATO model"
You just instructed ASCP not to consume this forecast. The source side forecast set must have "consume forecast" selected.
Starting in 11.5.10 release, Oracle implemented very significant improvements for CTO model forecast consumption. The old MRP process supported forecast consumption for one level in the sales order organization only. Oracle ASCP 11.5.7 through 11.5.9 supported multi-level, multi-org forecast consumption for one source of organizations only.
So yes, your requirement is supported in 11.5.10 and later releases. ASCP will perform forecast consumption in this order:
1. Consume the forecast for that specific Configured item (if entered)
2. Consume the forecast for any remaining sales order demand for the referenced ATO Model.
3. Explode the bill and consume the forecast for lower level options, subassembly configured items, and ATO models as needed.
To support this in a multi-org environment you will need to provide a global forecast and appropriate sourcing assignments.
Regards,
Kevin Creel
Come visit us at www.inspirage.com

SCCM 2007 - All clients from primary site have vanished from central site collections

Hi all,
we have a SCCM 2007 R2 setup with one central site, one Primary Site (A) with a secondary site hanging off it and another Primary Site (B). Suddenly all the clients from the Primary Site A (and also it's Secondary Site) have vanished from the central
site. All the clients are still present when we check Collections from the admin console on Primary Site A site server - they have simply disappeared when we check Collections from the Central Site admin console.
Can anyone provide any info on a good starting point for troubleshooting this issue? As a sidenote, we can still push packages out to the Primary Site A distribution point and both the Primary and Central site can communicate/ping each other.
Any help/info would be much appreciated!
Thanks

Check the
site replication on central site, is that SQL is working fine, and also see the
inbox folder in central site, might be there is backlog and those DDR files are
not processing, and after maintenance they got deleted.<o:p></o:p>
please run
the heartbeat discovery by hour or day, and once the clients will sent all the
DDR files then they will appears again.<o:p></o:p>
Sharad Singh | My blogs: SharadTech | Twitter:
@SinghSharaad | | Please remember to click “Mark as Answer” on the post that helps you.This can be beneficial to other community members reading the thread.

How do i create a workflow to delete tasks.

I've created a workflow that will take the Title, Start Date, and End Date from one list (roomReserved) and then create a task on another list (centralCal) setup as a central calendar. When a yes/no checkbox is checked, it will then create the task on the
centralCal. The problem I'm having right now is i am unable to remove or delete the task created in centralCal when the checkbox is unchecked.
I way I'm trying to delete the task in the workflow is:
if current item:checkbox equals no
then delete item in centralCal
in the "Choose List Item" popup menu
I choose List:centralCal
Find the List Item:
Field: Title
Value:
Lookup for Single line of text (popup)
Data source: Current Item
Field from source: Title
Return field as: string (greyed out)
To make sure the correct item is deleted I'm comparing the titles from the roomReserved and centralCal.
What I want the workflow to do is delete the task from centralCal if the checkbox is unchecked from roomReserved. Any idea's on how to change my workflow to fix this would be greatly appreciated.

Hi James,
I tried reproducing the issue in my environment. I created a list1 with two column: title and checkbox, a list2 with one column: title.
I created two workflows in SharePoint Designer: workflow1, if current item checkbox field equals yes, create item in list2, title= current item title. Workflow1 start automatically when an item is created.
Workflow2: if current item checkbox field equals no, delete item in list2. Choose List Item is set as below, and workflow2 starts automatically when item is changed.
Regards,
Rebecca Tu
TechNet Community Support

Creation of Delivery in ERP and Retriving in EWM

I created inbound delivery from the purchase order in ERP then I was trying to find this delivery in EWM
I am not seeing
Is there anything I need to configure or some step i need to do so that I can check delivery in EWM

after creating the Delivery in ERP, make sure you get the status message as 'Delivery # created and successfully distributed'. There is no config necessary in EWM system to be able to create IDN and ODRs based on ERP ID and ODs respectively. check the following and make sure everything is okay.
1. Setup the RFC connections b/w ERP and SCM,
2. Map the intermediate warehouse to EWM warehouse in both ERP and SCM systems
3. Setup the de-centralized warehouse settings in SPM node
4. Setup the delivery split based on warehouse and delivery type
5. Create the distribution model in ERP
6. setup the queues
7. setup the availabilty groups and stock types in SCM system.
I do not remember all the settings, you might want to check for the exact error in ERP & SCM systems using SMQ1, SMQ2 and SLG1 transactions. Provide us the exact error would really help. Good luck!!

Client Auth and SSL with Seeburger AS2 adapter

Hello All,
We are using the Seeburger AS2 adapter in our landscape and I am in the process of setting the same up and have made quite some progress in all my issues.
and I hope that you will be able to help me out.
1. Server SSL on Receiver AS2 adapter
I am sending a message from XI using the Receiver AS2 adapter to my AS2 test tool using Server SSL.
This is working perfectly fine. In my AS2 adapter I have selected HTTPS as the protocol and the message goes via SSL to the target test tool, is processed and the MDN comes back to XI perfectly.
The issue here is :
Irrespective of what is provided in the Server Certificate ( Keystore) , the message goes to my target test tool. I even left this field blank with no certificate entry and still the SSL connection was established and the message went to the target system.
Is there no validation that XI does here? I am lost what is the use of this entry Server Certificate if XI blindly accepts all SSL connections.
I am using a Decentral Adapter Engine with LoadBalancer.
2. Client Auth on Receiver AS2 Adapter
I tried to perform Client Authentication by proving my Server's private key in the AS2 adapter. The corresponding public key is loaded in my partner's Keystore.
XI error's with the error "SSL handshake failed - Bad Certificate" .
I am not sure why XI is erroring out here and I have a feeling that I have misunderstood the use of the fields in the AS2 adapter,
Server Certificate ( Keystore) and Private Key for Client Authentication.
Has anyone tried this? If further details are needed, I will be able to furnish the same.
Regards,
Bhavesh

Hello Jens,
Thanks for your reply.
1. The Encryption and Signature part of the Interface is working absolutely fine and I use the same concept highlighted by you - The Sender always signs the message with his private key and encrypts with message with the partner's public key in the corresponding agreement.
2. Server SSL is also working perfectly fine, i.e, when XI initiates the connection the SSL connection is established to the partner.
3. Mutual Auth was the issue where I was getting the bad certificate issue.
To investigate further I moved the same setup to my Central Adapter Engine and all the issues I had described above seem to have vanished and things work exactly as I was expecting, ie.
The field : Server Certificate (Keystore) is used to provide the Target System's Server SSL's public Certificate.
The field : Private Key for Client Authentication is used where XI provides its own Server SSL's private key for Mutual / Client Authentication.
The problem seems to be with my Decentral Adapter engine and not my central adapter engine and so I guess,
1. I either have the incorrect certificates on my Decentral Adapter Engine.
2. I also have 2 instances of a Decentral Adapter Engine with a Webdispatcher and so maybe the 2 Visual Admin's of the 2 Decentral AE are inconsistent.
3. Maybe it was just a long day and I did something wrong
Will investigate further for the root cause but I am glad that my concepts remain intact and things do work as I expected them to work.
A blog on all this is on the cards sometime soon.
Cheers,
Bhavesh

Non-durable Topic subscription with ClientID in a cluster environment

forgive me for asking this, i spent the entire day trying this out in my pc but still not able to get the exact result.
If i deploy an MDB on jms2 server with the following configuration in a cluster enviroment (jms1[masterbroker] <--> jms2) under Sun Application Server 9,
<activation-config-property-name>imqEnableSharedClientID</activation-config-property-name>
<activation-config-property-value>true</activation-config-property-value>
<activation-config-property-name>clientId</activation-config-property-name>
<activation-config-property-value>445566</activation-config-property-value>what should i expect if i issue the following command to jms1 and jms2?
1. imqcmd list dur
1-1. will there be an INACTIVE durable connection for jms1?
1-2. will there be an INACTIVE durable connection for jms2?
2. imqcmd query dst -t t -n TestT <- i want to know the number of consumer(s).
thanks and hope you can enligthen me.

I found a Metalink entry how you can configure the Oracle Enterprise Manager in a FailSafe Environment but only for Grid Control:
Note:396659.1 How To Setup Grid Control Central Agent Manually in Oracle Failsafe Environment
Is there a script/guide to do it with the local "enterprise manager database control"?
Replying to mnazi: Ok it is an overview and they mean that it is better to implement the enterprise manager to a management server but I couldn't found any hot information in the documentation to that. Maybe you know further info's?

Database control in a two node oracle fail safe cluster

os windows server 2003 r2
db 10.2.0.4
ofs 3.4.1
i've configured db control in the following
D:\oracle\product\10.2.0\db_1\BIN>emca -config dbcontrol db -repos recreate -cluster_name name_of_the_cluster
is this right?
next question
the -cluster flag and the -EM_NODE / -EM_SID_LIST parameters in the emca are only for rac?
with my configuration i can't login to my database over dbcontrol
Listener refused the connection with the following error: ORA-12514, TNS:listener does not currently know of service requested in connect descriptor The Connection descriptor used by the client was: (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=node1.blah)(PORT=1521)))(CONNECT_DATA=(SERVICE_NAME=ABBA)))

How to Configure the 10.2 DB Control in a Failsafe Environment
ID: 452305.1
HOWTO: PUBLISHED 17-OCT-2008
In this Document
   Goal
   Solution
   References
Applies to:
Enterprise Manager Grid Control - Version: 10.2.0.1 to 10.2.0.3
Information in this document applies to any platform.
Goal
The goal of the document is to provide the steps to configure the DB Console in an Oracle Failsafe environment.
Please note that the solution offered in this document is not certified by Oracle. It's only provided as a workaround for customers who wish to use this setup for the Database Control Console in a failsafe environment. Support for the procedure outlined in this document will be provided on a 'best efforts' approach.
As an alternative to this approach you can use Grid Control Agents to monitor a database in a failsafe environment. For more details please see:
Note 396659.1 How To Setup Grid Control Central Agent Manually in Oracle Failsafe Environment
We assume the following:
- the database binaries are installed on each node on the local disk
- you already have a failsafe group with the database, the listener, disk resource, and virtual
ip/hostname
Note: This is specific for Windows environments using Oracle Failsafe. For setting up the DB Console in Active/Passive clusters on UNIX please use the following note instead:
Note 362524.1 Configure DB Control 10.2 for use in Active/Passive High Availability Environments
Solution
1. Drop the DB Control repository and configuration files on the active node:
<ORACLE_HOME>/bin/emca -deconfig dbcontrol db -repos drop
2. Recreate the DB Control using the virtual hostname:
- in a command window do the following:
set oracle_sid=<your_sid>
set oracle_home=<your_oracle_home>
set oracle_hostname=<virtual_hostname>
cd %oracle_home%\bin
emca -config dbcontrol db -repos create
-- make sure that the virtual host name was picked up by emca (it will display a summary screen
before continuing)
3. Verify that the DB Console works fine and can be accessed using the virtual host name in the URL
4. Stop the DB Console
5. Create a directory path on the group disk resource similar to your oracle home path on the local disk.
For example:
If the oracle home on the local disk is C:\oracle\product\10.2.0\db_1 and the shared disk is D:
then create the following path: D:\oracle\product\10.2.0\db_1
Copy C:\oracle\product\10.2.0\db_1\<hostname_sid> and
C:\oracle\product\10.2.0\db_1\oc4j\j2ee\OC4J_DBConsole_<hostname_sid>
to D:\oracle\product\10.2.0\db_1\<hostname_sid> and respectively
D:\oracle\product\10.2.0\db_1\oc4j\j2ee\OC4J_DBConsole_<hostname_sid>
Remember to change the values enclosed in <> with those in your environment.
6. Delete the following directories from the local disk
C:\oracle\product\10.2.0\db_1\<hostname_sid>
C:\oracle\product\10.2.0\db_1\oc4j\j2ee\OC4J_DBConsole_<hostname_sid>
7. Create NTFS junction points from the local disk to the shared disk (these work like symbolic
links on UNIX) . It is your responsibility to create these.
You can find a brief guide as well as some tools that will help you create them at:
http://en.wikipedia.org/wiki/NTFS_junction_point
http://www.microsoft.com/technet ... dDisk/Junction.mspx
Important: Please note that this functionality is not certified nor supported by Oracle. Make sure you understand the
implications. Especially don't delete the junction points from Windows Explorer !!
In the end you should have the junction points on the local disk (with the same names as the
original directories) that would point to the directories you copied on the shared disk.
8. Start the DB Console service and verify that everything is still working fine.
9. Stop the DB Console service.
10. Move the Fail Safe group to the 2nd node.
11. Once the database is started, create the DB Console configuration files on the 2nd node:
<ORACLE_HOME>/bin/emca -config dbcontrol db
12. Stop the DB Console
13. Delete the created configuration files from the local disk:
C:\oracle\product\10.2.0\db_1\<hostname_sid>
C:\oracle\product\10.2.0\db_1\oc4j\j2ee\OC4J_DBConsole_<hostname_sid>
14. Create junction points from the local disk to the directories already located on the shared
disk.
15. Start the DB Console service and verify that is working fine.
16. Add the DB Console service as a resource to the fail safe group and put dependencies on the
database and listener services.
17. Perform a fail over and see if everything works fine.
References
Note 298238.1 - Oracle10g Grid Control with Oracle Fail Safe
Note 362524.1 - Configure DB Control 10.2, 11g for use in Active/Passive High Availability Environments
Note 396659.1 - How To Setup Grid Control Central Agent Manually in Oracle Failsafe Environment
Keywords
EMCA ; DB~CONTROL ; FAILSAFE ; DBCONTROL ; ENTERPRISE~MANAGER ;

Database control in a cluster environment

Hello DBA's
Is it possible to use the database control in a windows cluster with oracle fail safe? I haven't found any documentation to this topic (only with RAC).
I have two possibility's:
1. To use it as a cluster service where I could connect with the clustername/IP address?
Yet couldn't configure it right by my own.
2. To use it as normal service where allways the active note can connect to the database control? (Problem with the Host-Names because each note has there own)
I use Oracle 10.1.0.4 database with NO grid control only em database control.

I found a Metalink entry how you can configure the Oracle Enterprise Manager in a FailSafe Environment but only for Grid Control:
Note:396659.1 How To Setup Grid Control Central Agent Manually in Oracle Failsafe Environment
Is there a script/guide to do it with the local "enterprise manager database control"?
Replying to mnazi: Ok it is an overview and they mean that it is better to implement the enterprise manager to a management server but I couldn't found any hot information in the documentation to that. Maybe you know further info's?

SolMon 3.2, Difference between SolMon report and Service .sap report?

Hi Guys,
last week i found one strange thing, there are differences between the reports of our local SoMon server report and report from service.sap (service message).
why there will be difference like this, Please help me in this regards.
Regards
Srini

Software Components for SAP Solution Manager 4.0 as of April 2007.
SAP_BASIS 700           Basis Component
SAP_ABA       700           Cross-Application Component
PI_BASIS 2005_1_700     PI_BASIS 2005_1_700
ST-PI     2005_1_700     SAP Solution Tools Plug-In
SAP_BW    700           SAP NetWeaver BI 7.0
SAP_AP    700             SAP Application Platform
BBPCRM    500           BBPCRM
CPRXRPM   400           SAP xRPM/cProjects/cFolders 4.00 (ABAP)
ST        400           SAP Solution Manager Tool
ST-A/PI       01I_CRM500    Application Servicetools for CRM 500
ST-ICO       150_700       SAP Solution Manager Implementation Content
ST-SER    700_2006_2    SAP Solution Manager Service Tools
ST (Solution Manager Infrastructure, tx solution_manager, SOLAR01)
ST-A/PI (Download modules to get data for service sessions, monitoring)
ST-ICO (Implementation Content - Business Process Repository)
ST-SER (Service Sessions as EarlyWatch Alert, SAP GoingLive Check, Setup System Monitoring, Central System Administration, Setup Business Process Monitoring, Service Level Reporting, ....)
See also SAP Notes:
- 707705 (www.service.sap.com/sap/support/notes/706705) for an explanation on Components for Messages (with lots of key words).
- 394616 (www.service.sap.com/sap/support/notes/394616) Release strategy for SAP Solution Manager
Best regards
Ruediger

Active Directory integration with Solman 71. ITSM and Business Partners

Good morning.
We have 30 000 users on the Active Directory. All these users must be able to log a call via Solman 7.1. Is there a way to avoid creating the 30 000 users on the Solman system by integrating Solman & AD & automatically assigning the BP to the user(s)? What alternatives are there?
Kind regards,
Mojo

Hi Mojo,
You can setup the CuA (Central User Administration) to synchronized all your LDAP database to the cua. Then you solman will have to be declare on each ...
Notes = CuA is a old technology which works fine ... but SAP does not really support it. New product is called "IDM". It does request to your need I think..

Setup of ASCP centralized

Similar Messages

Maybe you are looking for