SG300-10 (1.4.0.88) Layer-3 Mode

I'm having an issue getting my SG300-10 into Layer-3 mode. I had it in Layer-3 mode under version 1.3.7.18, performed a factory reset by holding down the hard-reset button for 10 seconds. Updated boot loader to 1.3.5.06 and SW Firmware to 1.4.0.88.
switchc4f42e#sh ver
SW version 1.4.0.88 ( date 06-Aug-2014 time 16:55:55 )
Boot version 1.3.5.06 ( date 21-Jul-2013 time 15:12:10 )
HW version V02
Now I cannot find the option to switch it back into Layer-3 mode. There is no "menu" option at the console (serial).
switchc4f42e#
boot Boot Commands
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
copy Copy from one file to another
crypto Cryptographic commands
debug-mode Exit from the EXEC to debug mode
delete Delete a file from the flash file system
dir Display the list of files on the flash file system
disable Disable privileged commands
dot1x 802.1x EXEC commands
errdisable Err-Disable shutdown commands.
exit Exit from the EXEC
green-ethernet Green ethernet commands
help Description of the interactive help system
ip Global IP configuration commands
login Exit from the EXEC and Log in
macro Ports macros
more Display a file
no Negate command
ping Send echo messages.
reload Halt and perform a cold restart
rename Rename a file
renew Renew DHCP address
resume Resume telnet session.
set Set System Parameters
show Show running system information
telnet Open telnet session.
terminal Set current session functions
test diagnose
traceroute Discover the routes to destination.
write Write running configuration to memory or terminal
switchc4f42e#menu
% Unrecognized command
switchc4f42e#
What do I need to do to get this switch back into Layer-3 mode?

Never mind, I found it ....
switchc4f42e#set system mode router
Changing the switch working mode will *delete* the startup configuration file and reset the device right after that. It is highly recommended that you will backup it before changing the mode, continue ? (Y/N)[N] Y

Similar Messages

History Panel Option to ignore Layer Blend Mode Changes

Using shift+plus and minus keys to see various layer blend modes eats up my History. Not quite sure why it even records... you can't use the History Brush to "blend" previous blend modes. And it is not difficult to go back to a previous blend mode. I'd like to see a History Option to ignore Layer Blend Mode Changes, like you have for Layer Visibility Changes.

OK. Changes in the Blending Dialog don't record in History until committed.Thanks!
But I don't see a way to quickly go through the various Blend Modes like you can with Shift+ plus/minus keys. I really like that keyboard method to rapidly view and compare various Blend Modes.

How to bulid new layer blend modes?

please look link: https://forums.adobe.com/thread/1755389
I did not learn Microsoft Visual Studio, I want to use my algorithms, have same functionin as The layer blend modes in photoshop , but algorithm not the same , written in JavaScript to run very slowly, pls help me.
thx

inline unsigned8 Mul8x8Div255 (unsigned8 a, unsigned8 b)
unsigned32 temp = (unsigned32)a * (unsigned32)b + 128; //how modify here?
return static_cast<unsigned8>((temp + (temp >> 8)) >> 8); //how modify here?
inline unsigned16 Mul16x16Div32768 (unsigned16 a, unsigned16 b)
unsigned32 temp = (unsigned32)a * (unsigned32)b + 16384; ////how modify here?
return (unsigned16) (temp >> 15); ////how modify here?
inline float Mul32x32(float a, float b)
if(a>=b){
rerurn 255-(510-a-b-(255-a)*(255-b)*(b+255)/(255*255)); //here ok
else {
return 255-(510-a-b-(255-a)*(255-b)*(a+255)/(255*255)); //here ok
pls help me
how modify:
inline unsigned8 Mul8x8Div255 (unsigned8 a, unsigned8 b)
unsigned32 temp = (unsigned32)a * (unsigned32)b + 128; //how modify here?
return static_cast<unsigned8>((temp + (temp >> 8)) >> 8); //how modify here?
inline unsigned16 Mul16x16Div32768 (unsigned16 a, unsigned16 b)
unsigned32 temp = (unsigned32)a * (unsigned32)b + 16384; ////how modify here?
return (unsigned16) (temp >> 15); ////how modify here?

SF 300-24 in layer 3 mode

I have a layer 2 switch, cisco SF 300-24. It's firmware has been upgraded to 1.3.0.62 and has been configured as layer 3. Inter-VLAN routing is also enabled, however, it only supports static routing, not dynamic. Our requirement of the network is that:
1). there should be three VLANs: e.g. VLAN 10, 20 and 30.
2). systems on VLAN 10 should not communicate with any other systems
3). One PC of VLAN 20 should be able to access two PCs of VLAN 30; the rest shouldn't
Is it possible that only one system of VLAN can access two other of a different VLAN without the use of a separate router, since it is already on layer 3 mode.

A little up ? ;-)

SF302-08P layer 3 mode

Hi,
i'm trying to configure SF302-08P in layer 3 mode.
ports 1 to 8 have ip phones and desktops, port GE1 in connected to a router (not cisco) that links to the internet.
i created vlan 100 and assigned to ports 1 to 8 (untagged)
i created vlan 200 and assigned to port ge1 (untagged)
activated dhcp server , created pool with 192.168.26.0/24 gw 192.168.26.1
                       |router A| (192.168.16.0/24 gw 192.168.16.1)
                           |
                           |
                           | GE1 (192.168.16.14)
                       | SF302-08P |
                                 |
                                 |
SPA504G+DESKTOP |    SPA504G+DESKTOP
        192.168.26.2                      192.168.26.4
         192.168.26.3                      192.168.26.5
the problem that i'm facing is that SPA504G and desktops access the internet with their inter address 192.168.26.0/24 and not 192.168.16.14.
is there a way to achieve what i'm looking ? how does routing work in this case ? shouldn't there be some kind of NAT ?
thank you

Hello Luis,
Is there a particular reason that the switch needs to be in Layer 3 Mode?
I think your scenario would work better if you configure NAT on your router and let the router act as the DHCP server. Then, the switch could be in Layer 2 Mode.
Alex

Adobe After Effects 7, Layer/Transfer/Mode/Screen

Hi
I have Adobe After Effects 7 and I'm folowing a tutorial on the internet and it says I should go to Layer/Transfer/Mode/Screen. Fair enough, sounds easy peasy, but there is no menu for that. So do you know if its located somewhere esle in the program, thanks...

Since After Effects is not an Apple product, you'd probably be better off posting your question on Adobe's discussion forums:
http://www.adobe.com/go/gntraysupp_forumshome

Has anyone ever encountered layer blend modes behaving strangely?

I use photoshop quite a bit for retouching and photo compositing. Tonight I encountered a strange problem. I was trying to create a vintage look on a photo and had a number of adjustment layers including a curves, levels, color fill and there were also a few texture/noise layers all set to varying opacities. Near the top of all this I had a vignette layer that was black around the edges and white in the center set to blend mode of multiply. Well, when I was clicking on and off I realize that that vignette layer was definitely lightening the center part of the overall image quite a bit (the part that is white on the vignette layer), almost like a screen. So I flipped the vignette layer through different opacity modes and saw that there was no change in its behavior, every mode was screening the white, even darker color and multiply. I thought maybe it was interacting in a weird way with one of the other layers so I turned all the others off except the back ground-- still no change. Then I dropped the layer down one at time until it was below the background. When I started to move it up again, it was behaving normally for a moment until I moved it up a couple levels in the stacking order and then it went back to the screen behavior. Anyway I shuffled it around a bit but there was no consitency to when it would display the correct opacity and when it wouldn't, so it did not seem to be an interaction with any specific layer. I don't know, but I can't really think of any case where white set to multiply should produce a lighter result even if it were interacting with another opacity. In any case it does seem to me that there is something going on with the overall computation of opacities. I tried creating a new black and white layer and it was also doing the same thing, behaving strange and not displaying the correct opacity.
I'm tired, so I'm going to bed. I'm going to shut off the computer and hope this goes away when I reboot, but if it does not, does this sound familiar to anyone? I'm not a regular visitor to this forum, but I thought I'd put it out there in case anyone else has experienced anything like this. I've only got 5 gigs of ram on this computer and I've been working away for a while... maybe photoshop just couldn't keep up(?) I'm using Photoshop CS5, RGB Adobe 1998 colorspace. I've never had anything like this happen in the last 11 years I've been using photoshop. Hmmm.... hope I don't have to reinstall or call support or worse. fingers crossed.

Nevermind. It is still having the problem. I have to think that this file is just corrupt somehow because I just opened another file and can't seem to cause the same problem. Basically, I can fill a layer with white, put it to a blend mode of multiply or darker color and it will block out everything of the image below, ie totally opaque. The opaqueness varies depending on the if there are other layers also on blend modes, but it does not seem to correspond to normal blend mode interaction. If I put it right on top of a regular layer with an image on it, it totally blocks it out on a blend mode of multiply... weird. I am going to scrap this file and see if the problem recurs in other files. My 2006 Mac Pro is getting some years on it and has been running pretty slow. I'm not a hardware expert but I've done everything I know how to do to maintain it. Was thinking of upping the ram to see if I can hold out a bit longer before I upgrade the computer. Wouldn't surprise me if this problem is related to the computer.

I can't set a layer blend mode to "Screen"

Hello, I'm new to Photoshop as of an hour ago (I've been using GIMP for 2 years).
I have a layer selected and I want to set the blend mode to "screen". However, the screen mode as well as several others are greyed out and won't let me select them. I'm using Windows 8 Home Premium 64 bit, and Photoshop CS6 Extended (Trial) 64 bit. I'm intending to get Adobe Creative Cloud tomorrow, but is the reason for this that I'm using the trial version? If not, what am I doing wrong? There is a screenshot below to show what I am talking about. Any help would be appreciated. Thank you!
http://i1289.photobucket.com/albums/b504/thomasbowe34/ps_zpsc5e055f5.png

Took me a few second to figure out whats wrong. But the answer is, you're in the 32 bit mode. Changing the mode to 16 or 8 { (Image>Mode>8Bits/Channel) or (Image>Mode>16Bits/Channel) } will make it available.

Why is a layer blending mode result altered by adding and effect?

I've done a search online and haven't come up with an answer but does anyone
know why a layers blending mode result is altered by adding an effect?
I am using CS3 on a PC (Windows XP SP2) and have two layers; one a Tiff and
a second a text layer with an ambient light and a spot shining on them. Both
layers have 3D turned on and accept lights and are in the same position in
space.
To make the text, which is coloured black, sit better I changed the layers
blend mode to soft light which works well.
I wanted to soften the edge of the text a little so I added a Fast Blur
effect and suddenly the result of the blend was completely different. If I
turn off the effect it goes back to what it was before but even if the Fast
Blur is set to zero, ie no blur on the layer, the blend result is altered.
Does anyone know what's going on?

Many thanks for that. I tried the Box Blur but it too shifted the result of the blend. In the end, to get this job out of the door, I changed the colour of the text to orange, lowered the opacity and used Multiply as the layer blend mode. Adding the Fast Blur effect to this didn't shift the result of the blend mode. It's not as sexy a look as using Soft Light but it works. I wonder if it's something going on with the maths or this a real bug? <[email protected]> wrote in message news:[email protected].. > Presumably a bug that uses the blur's convolution kernel when it > shoulddn't. Please report at <a href=http://www.adobe.com/go/wish>. Still, > sometimes changing the blend behavior is inevitable. Even if the layers > visually look the same, the actual pixel values may change and thus create > a different result in the blend formulas. That should not be the case > here, though. Replace the Fast Blur with Box Blur set to 8 or 9 iterations > and the result should look the same, but without the blending problem, I > guess. > > Mylenium

Configuring a AP 1552EU-A-K9 in layer 2 mode thru a WLC 5508 running 7.6.130.0

We have an outdoor AP that we want to bridge to another one that is also outside and connect to our WLC 5508. I see a lot of data for connecting via a layer 3 network, but nothing yet on a layer 2 network (which we run). Can anyone point me to some doc that would explain this?

We have an outdoor AP that we want to bridge to another one that is also outside and connect to our WLC 5508. I see a lot of data for connecting via a layer 3 network, but nothing yet on a layer 2 network (which we run). Can anyone point me to some doc that would explain this?

I cannot paint or use gradients correctly in layer mask mode

I have my blending mode set to 'NORMAL". When I paint in black on a layer mask it creates a transparent effect (not hide the image/pattern). Since the upgrade this has affected both my pc and laptop versions. I've read through the forums and see a lot of folks having issues with the blending mode set inccorrectly but this seems different. I'm at a loss and losing time. Any help would be greatly appreciated.

Um, painting black on a layer mask is supposed to create transparency (and gray partial transparency). Unless I'm missing something subtle, it appears to be working correctly from what I can see.
Keep in mind the checkerboard is not really in the document - it's just Photoshop's way of showing you that the layer is transparent. You can set how that's portrayed in the Preferences - Transparency and Gamut section.
Or you can enable the visibility of your Background layer to see what it looks like when that shows through.
-Noel

Layer Blend mode won't show in Export?

Hi there,
I'm trying to export a composition and one of the layers has the "Multiply" blend mode applied. It looks great in the composition, but when I export it and bring it into Premiere, the layer seems to revert to a "Normal" blend mode (Its a gray bar, so It looks drastically different when the multiply blend is active).
I am using RGB+ Alpha, Apple Prores 4444. Is there a setting I can change or some way to fix this? Thanks.

Are you rendering the entire shot including the layer below your gray bar? You may be having gamma issues with Prores. You haven't given enough details to know exactly what's going on, but my first guess is a gamma issue. Try exporting an image sequence or just render animation uncompressed or uncompressed with Alpha if you need the alpha channel in Premiere.
If you are expecting the multiply blend mode in the gray bar to multiply with a layer below your rendered footage in a Premier sequence, that's not going to happen.

Masking "disables" layer blending modes!

Hi there,
i have a comp with a bunch of layers and one of them has multiply as blending mode! (ambient occlusion layer)
so far everything went fine but as soon as i want to mask a certain part of the comp the blending mode get´s "disabled"...
Doesn´t matter what type of mask i use it´s always the same issue... it´s rly anoying =/
Directupload.net - dolpbyml.jpg
Did i missing something?!
Greez
Lana

Sry... AE CC
http://abload.de/img/layersjno5l.jpg
In my opinion theres rly nothing fancy about! Just a few passes rendered out in cinema 4D!
And as said everything works fine as long as i don´t mask the composition

Brush tool color mode vs layer color mode

When using the brush tool what is the difference between using
the brush in color mode on a normal layer vs using
the brush in normal mode on a color mode layer?

Tools do not have dynamic Blend modes, Fill or Opacity adjustment settings as the Layers do. You can set opacity on a tool,but once you make that stroke, it stays at that setting. You can always change the blend mode,opacity or fill on a layer. That's just one difference I know about.
Here's a great reference on Blending modes.
http://photoblogstop.com/photoshop/photoshop-blend-modes-explained
Gene

Illustrator CC Layer Blending Modes not working

Did Adobe do something to Illustrator CC that the layers with the same object colors are no longer blending. No matter what blend mode I apply the object never blends with the object with the same color behind it
Any ideas?

Document settings? What colors? Screenshots?
Mylenium

SG300-10 (1.4.0.88) Layer-3 Mode

Similar Messages

Maybe you are looking for