Show conn state and fix-ups
Can the show conn state command be used to monitor the connections for fix-up protocols?
Use the show port status command to display port status information.
show port status [mod_num[/port_num]]
Syntax Description
mod_num
(Optional) Number of the module.
/port_num
(Optional) Number of the port on the module.
This example shows how to display port status information for all ports:
Console> show port status
Port Name Status Vlan Level Duplex Speed Type
1/1 connected 523 normal half 100 100BaseTX
1/2 notconnect 1 normal half 100 100BaseTX
2/1 connected trunk normal half 400 Route Switch
3/1 notconnect trunk normal full 155 OC3 MMF ATM
5/1 notconnect 1 normal half 100 FDDI
5/2 notconnect 1 normal half 100 FDDI
Similar Messages
-
ACE Sticky Connections, Show Conn Output and Show serverfarm
Hi Community,
I'm deploying a Cisco ACE module and I have some questions about sticky connections and about the output of the show conn command and show serverfarm command.
I have the follwoing configuration:
rserver host srv_1 ip address 10.4.11.14 inservicerserver host srv_2 ip address 10.4.11.18 inserviceserverfarm host farm_144 rserver srv_1 144 weight 1 inservice rserver srv_2 144 weight 3 inservice
sticky ip-netmask 255.255.255.255 address source st_host144
timeout 10080
serverfarm farm_144
class-map match-all vip_144
2 match virtual-address 10.4.11.208 tcp eq 143
policy-map type loadbalance first-match lb_144
class class-default
policy-map multi-match policy_vip_webcache
class vip_webcache_144
loadbalance vip inservice
loadbalance policy lb_144
loadbalance vip icmp-reply active
nat dynamic 411 vlan 411
We can assume that service policy was applied at the interface vlan. So, let's go to the questions:
1- If sticky is enabled the output command "show conn" should show just one entry by ip address?
The real output is:
DC01-ACE-01-PRIMARY-SW1/context_servidores# show conn | inc :143333046 1 in TCP 411 10.2.158.87:3616 10.4.11.208:143 ESTAB 286390 3 in TCP 411 10.2.158.87:3562 10.4.11.208:143 ESTAB310233 1 in TCP 411 10.1.5.87:3424 10.4.11.208:143 ESTAB
Look that the ip address 10.2.158.87 is shown 2 times. In same times, the same ip address is shown 4 times to the same VIP and the same port. Is it a normal behavior?
2- According to the configuration, the srv_2 has weight 3 and srv_1 has weigth 1, but the output of show serverfarm show somethin strange:
DC01-ACE-01-PRIMARY-SW1/context_servidores# show serverfarm farm_144 serverfarm : farm_144, type: HOST total rservers : 2 state : ACTIVE DWS state : DISABLED --------------------------------- ----------connections----------- real weight state current total failures ---+---------------------+------+------------+----------+----------+--------- rserver: srv_1 10.4.11.14:144 1 OPERATIONAL 11 386 0 rserver: srv_2 10.4.11.18:144 3 OPERATIONAL 35 66 0
We can see that the weight is working good, but the total of connections is higher at srv_1 than srv_2. Why?
Somebody can help me to understand better this problem of if its a normal behavior?
Thanks in advance!!Hi Gaurav,
About question 1, I got some informations too. It's perfectly normal the client open 2 or more connections at the same time. The client's application is the responsable. We removed the ACE and put the client directly to the server and the result of the total connections opened was the same.
About question 2, I made some "clears" on the serverfarm, the sticky database and after that, the numbers were more real.
DC01-ACE-02-SECONDARY-SW1/context_servidores# sh serverfarm farm_webcache_144
serverfarm : farm_webcache_144, type: HOST
total rservers : 2
state : ACTIVE
DWS state : DISABLED
----------connections-----------
real weight state current total failures
---+---------------------+------+------------+----------+----------+---------
rserver: srv_webcache_1
10.4.11.14:144 1 OPERATIONAL 1025 15499 4436
rserver: srv_webcache_2
10.4.11.18:144 2 OPERATIONAL 1794 33471 471
DC01-ACE-02-SECONDARY-SW1/context_servidores#
Anyway thank you very much for your feedback.
Plínio Monteiro -
Something was hidden in a download and now these double green underlined hyperlinks show up everywhere, and pop ups too whenever I click on ANYTHING. I can't figure out how to find it and get rid of it.
You installed the "DownLite" trojan, perhaps under a different name. Remove it as follows.
Malware is constantly changing to get around the defenses against it. The instructions in this comment are valid as of now, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for more recent discussions or start a new one.
Back up all data.
Triple-click anywhere in the line below on this page to select it:
/Library/LaunchAgents/com.vsearch.agent.plist
Right-click or control-click the line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item named "VSearch" selected. Drag the selected item to the Trash. You may be prompted for your administrator login password.
Repeat with each of these lines:
/Library/LaunchDaemons/com.vsearch.daemon.plist
/Library/LaunchDaemons/com.vsearch.helper.plist
/Library/LaunchDaemons/Jack.plist
Restart the computer and empty the Trash. Then delete the following items in the same way:
/Library/Application Support/VSearch
/Library/PrivilegedHelperTools/Jack
/System/Library/Frameworks/VSearch.framework
Some of these items may be absent, in which case you'll get a message that the file can't be found. Skip that item and go on to the next one.
From the Safari menu bar, select
Safari ▹ Preferences... ▹ Extensions
Uninstall any extensions you don't know you need, including any that have the word "Spigot" in the description. If in doubt, uninstall all extensions. Do the equivalent for the Firefox and Chrome browsers, if you use either of those.
This trojan is distributed on illegal websites that traffic in pirated movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect much worse to happen in the future.
You may be wondering why you didn't get a warning from Gatekeeper about installing software from an unknown developer, as you should have. The reason is that the DownLite developer has a codesigning certificate issued by Apple, which causes Gatekeeper to give the installer a pass. Apple could revoke the certificate, but as of this writing, has not done so, even though it's aware of the problem. This failure of oversight is inexcusable and has compromised the value of Gatekeeper and the Developer ID program. You can't rely on Gatekeeper alone to protect you from harmful software.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return. -
CAD Real Time Stats show NA for agent state and call log
Hello
For our lab uccx, the agent/users CAD display shows NA for the agent state and call log. I have
Not Ready and Log out codes set and have the testers do those actions to generate data.
I have rebooted the server and have also checked the services page and confirmed
all the services are running.
I went through the admin guide to see if I missed any configuration but does not appear so.
I tried launching the real time stats tool from the UCCX Admin and it launches OK
but I noticed that it shows not connected.
Note this is over a VPN to the UCCX.
So not sure if this is related. I checked the relase notes and this is the base install
of UCCX 8.5. I am going to install the service updates but wanted to see if I can
get this running before I schedule a maint window to do the upgrades.
Thanks
Mike KanaHi
you might be facing an issue where " uccxcaduser password" gets corrupted , which leads to the issue you are facing right now
you have to contact TAC to reset that password for you and your issue will be fixed ,100%
Note : Only TAC can reset this password -
Revision: 17872
Revision: 17872
Author: [email protected]
Date: 2010-09-27 08:04:40 -0700 (Mon, 27 Sep 2010)
Log Message:
Popup: Exposed set accessor of open for view state usage and fixed bug when closing from model within popup. http://www.spicefactory.org/forum/viewtopic.php?p=3932. Added new sample to show model and view state interactions.
Modified Paths:
cairngorm3/trunk/libraries/Popup/src/com/adobe/cairngorm/popup/PopUpBase.as
cairngorm3/trunk/libraries/Popup/src/com/adobe/cairngorm/popup/PopUpFactory.as
cairngorm3/trunk/libraries/Popup/src/com/adobe/cairngorm/popup/PopUpWrapper.as
cairngorm3/trunk/libraries/PopupTest/.actionScriptProperties
cairngorm3/trunk/libraries/PopupTest/src/samples/MyPopup.mxml
cairngorm3/trunk/libraries/PopupTest/src/samples/PopUpPM.as
Added Paths:
cairngorm3/trunk/libraries/PopupTest/src/PopUpModelExample.mxml
cairngorm3/trunk/libraries/PopupTest/src/samples/MyPopupWithModel.mxmlLots to be excited about. BUT...Just updated to 8.1 on one of my computers to test it out...
Sadly, the following issue is NOT fixed for me. Is it with new projects only? I haven't started a new project on 8.1 I've only opened an old project but the issue that I'm referring to which involves also a delay/freeze of anywhere from a few seconds to a MINUTE while the render bar goes from yellow to red and then back to yellow is still there. Boo.
On the list above...
Switching between sequences can turn the render bar red.
This issue is incredibly easy to replicate. I really do hope it gets fixed. Here are the steps:
1) Create two sequences with multiple short clips (the more clips the better)
2) Make sure GPU acceleration is enabled.
3) Add warp stabilizer to the clips in both sequences. Again, the more clips the longer the delay/freeze will be as the render bar goes from YELLOW to RED and then eventually back to YELLOW again.
4) Hit SAVE.
5) Now, toggle between sequences. You'll hit a short delay with a few clips stabilized and a LONG delay with lots stabilized. In my case this delay is around a full minute. The render bar will go from YELLOW to RED and then back to yellow...eventually.
6) Toggle back to the original sequence and the delay occurs again.
7) Once you've toggled between sequences and have gone through this delay, that's it, there is no longer a delay...UNTIL...(and here's the big kicker)...until the project is SAVED again. After that the issue returns when you toggle between sequences. Both saving manually and AUTOSAVING cause this issue. No way around it except not editing with GPU acceleration.
Not sure what the issue is...caching issue when saving maybe? Either way, it stinks and it's still there in 8.1. Big bummer.
Again, lots to be excited about with this release but I really was hopefully this specific issue was resolved.
Sigh. -
I purchased a season of a TV show from itunes and it won't go onto my ipad, i've purchased several seasons in the past and never had this issue, how can i fix this?
Drew how is that even possible? I use gift cards all the time, any time I've had insufficient funds iTunes will not allow the purchase, sights Insufficient funds and rejects the purchase. Any time I log into my account the money in that account appears in the upper left corner. If you're not seeing that then you have other issues. Anyway... Kneil is right you should be able to rip CDs you own to your iTunes library (regardless of your money matters with iTunes), then depending on how you set up the music you need to add it to your playlist and then sync it to your iPod. Did imported music ever work? How are you ripping or importing the music to iTunes? Are you using a compatible format?
Something else to look at-- It's possible your cable is defective, have you tried a new or different cable? Some of what your describing is a bad cable issue. Good luck, Cheers. -
I am currently deployed and was using my iMessage to be able to talk to family back in the states and my iMessage stopped working. It will no longer select my number to use as the send/receive. How do I fix this so I can continue to talk to family?
Read here:
http://support.apple.com/kb/TS2755 -
Have over 86GB of music now showing as "other" and although it is still on my iPod it is not playable. Most is from imported CDs. I do have a backup file on an external hard drive. How can I fix this?
To import music into your iTunes library on the computer go to iTunes>Help>iTunes Help>Add items to iTunes and follow the instructions
Delete the "songs" that do not play in your iTunes library and reimport them. -
Got action sequence to "loop" but it shows in all states - conditional statement to fix it?
Using Flash Catalyst & Notepad (to open and alter the code in the "Main" MXML file) I'm able to "loop" an action sequence on the home state for my swf by changing the code as follows:
ORIGINAL CODE
<s:Parallel id="Sequence3">
ALTERED CODE
<s:Parallel id="Sequence3" effectEnd="Sequence3.play()">
The desired effect is a sequence (of 4 images) that loops whenever a user is viewing the home state. It is activated "On Application Start"
The PROBLEM is that the loop continues in all other states (it appears in the background - behind the objects that are supposed to show up on the other pages and only begins to show up in each state when the sequence begins another loop).
I am assuming I need a conditional statement --- something along the lines of:
while (condition){ statements;}
...in other words, ONLY while currentstate = "Home" it should loop the sequence. What would be the correct code for this conditional statement and where would the conditional statement be inserted to loop the sequence as desired??? Or... is there another better way??
My current code for this action sequence is:
<s:Parallel id="Sequence3" effectEnd="Sequence3.play()">
<s:Parallel target="{designlayer1}">
<s:Fade alphaTo="0" duration="500" startDelay="2100"/>
</s:Parallel>
<s:Parallel target="{bitmapimage2}">
<s:Fade alphaTo="0" startDelay="2100"/>
</s:Parallel>
<s:Parallel target="{bitmapimage3}">
<s:Fade alphaTo="0" startDelay="2100"/>
</s:Parallel>
<s:Parallel target="{bitmapimage4}">
<s:Fade alphaTo="0" startDelay="2100"/>
</s:Parallel>
<s:Parallel target="{bitmapimage5}">
<s:Fade alphaTo="0" startDelay="1650"/>
</s:Parallel>
<s:Parallel target="{bitmapimage6}">
<s:Fade alphaTo="0" startDelay="1800"/>
</s:Parallel>
<s:Parallel target="{bitmapimage7}">
<s:Fade alphaTo="0" startDelay="1950"/>
</s:Parallel>
<s:Parallel target="{designlayer5}">
<s:Fade alphaFrom="1" alphaTo="0" duration="0" startDelay="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="2650"/>
<s:Fade alphaTo="0" startDelay="5300"/>
</s:Parallel>
<s:Parallel target="{bitmapimage8}">
<s:Fade alphaFrom="1" alphaTo="0" duration="0" startDelay="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="2650"/>
<s:Fade alphaTo="0" startDelay="5350"/>
</s:Parallel>
<s:Parallel target="{bitmapimage9}">
<s:Fade alphaFrom="1" alphaTo="0" duration="0" startDelay="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="2650"/>
<s:Fade alphaTo="0" startDelay="5350"/>
</s:Parallel>
<s:Parallel target="{bitmapimage10}">
<s:Fade alphaFrom="1" alphaTo="0" duration="0" startDelay="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="2650"/>
<s:Fade alphaTo="0" startDelay="5350"/>
</s:Parallel>
<s:Parallel target="{bitmapimage11}">
<s:Fade alphaFrom="1" alphaTo="0" duration="0" startDelay="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="2650"/>
<s:Fade alphaTo="0" startDelay="4750"/>
</s:Parallel>
<s:Parallel target="{bitmapimage12}">
<s:Fade alphaFrom="1" alphaTo="0" duration="0" startDelay="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="2650"/>
<s:Fade alphaTo="0" startDelay="5000"/>
</s:Parallel>
<s:Parallel target="{designlayer6}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="5900"/>
<s:Fade alphaTo="0" startDelay="7900"/>
</s:Parallel>
<s:Parallel target="{bitmapimage13}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="5900"/>
<s:Fade alphaTo="0" startDelay="7550"/>
</s:Parallel>
<s:Parallel target="{bitmapimage14}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="5900"/>
<s:Fade alphaTo="0" startDelay="7900"/>
</s:Parallel>
<s:Parallel target="{bitmapimage15}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="5900"/>
<s:Fade alphaTo="0" startDelay="7750"/>
</s:Parallel>
<s:Parallel target="{bitmapimage16}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="5900"/>
<s:Fade alphaTo="0" startDelay="7900"/>
</s:Parallel>
<s:Parallel target="{bitmapimage17}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="5900"/>
<s:Fade alphaTo="0" startDelay="7900"/>
</s:Parallel>
<s:Parallel target="{designlayer7}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="8500"/>
<s:Fade alphaFrom="1" alphaTo="0" startDelay="11000"/>
</s:Parallel>
<s:Parallel target="{bitmapimage18}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="8500"/>
<s:Fade alphaFrom="1" alphaTo="0" startDelay="11000"/>
</s:Parallel>
<s:Parallel target="{bitmapimage19}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="8500"/>
<s:Fade alphaFrom="1" alphaTo="0" startDelay="11000"/>
</s:Parallel>
<s:Parallel target="{bitmapimage20}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="8500"/>
<s:Fade alphaFrom="1" alphaTo="0" startDelay="11000"/>
</s:Parallel>
<s:Parallel target="{bitmapimage21}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="8500"/>
<s:Fade alphaFrom="1" alphaTo="0" startDelay="10650"/>
</s:Parallel>
<s:Parallel target="{bitmapimage22}">
<s:Fade alphaTo="0" duration="0"/>
<s:Fade alphaFrom="0" alphaTo="1" duration="0" startDelay="8500"/>
<s:Fade alphaFrom="1" alphaTo="0" startDelay="10800"/>
</s:Parallel>
</s:Parallel>
Thank you!!!!!!!!Figured out my issue...
I had to select each layer for the 4 photo sequence and "Remove From State" for each layer. If this is done with all layers except the "Home" state, the images show only where appropriate.
So... "Loop an action sequence" is really easy.
I've seen a lot of complaining that "FC can't do it" but with a very simple code mod, I was able to do it WITHOUT using the video timer method.
I should also mention that I've never worked with Flash at all before this project and am only self-taught in HTML (basics). I was able to make a pretty good looking Flash component for a web site and never would have attempted it without FC. I have to say, while FC is a bit limited, GUI-based Flash is a great add for Adobe and will save me over $2k per year in web admin.
To edit the document in Notepad as mentioned in the first post:
the full text can be found here http://www.judahfrangipane.com/blog/2010/09/03/flash-catalyst-jailbreak-for-flex-developer s/
Editing MXML Documents
To edit your projects MXML documents we first need to find the path to the Flash Catalyst workspace. To do this publish your Flash Catalyst project (CMD / CTRL + ENTER). Now, the browsers URL shows the path to the project workspace. So in this URL, "file:///Users/judah/Library/Application Support/Adobe/Flash Catalyst/workspace/Project/bin-debug/Main.html", the project MXML documents are located at, "file:///Users/monkeypunch/Library/Application Support/Adobe/Flash Catalyst/workspace/Project/" when on a Mac.
Flash Catalyst project files
Project Files Description
/src - location of the application source files
/bin - the location of any additional flex libraries
/bin-debug - location of testing swf
/html-template - location of the html template that wraps around your application
/src/Main.mxml - the main application file. make your application changes here
/src/Main.css - the css stylesheet of the main application
/src/components - the location of custom components and component skins
/src/assets/graphics - location of optimized FXG graphic symbols
/src/assets/images - location of images
You can edit these XML documents in any text editor. To apply the changes you need to save the file and refresh the Flash Catalyst project. You can do this by opening the changed document in Flash Catalyst code view. When we do this it will recognize the document has changed and prompt you to use the newer version of the file. Select Yes. If the project does not rebuild immediately publish it using CMD + Enter. -
i cant open iphoto here, open with a circle turning show loading,how to fix it. help!! i nit to reopen it and keep my precious photo
What version of iPhoto?
If it's 09 or later try
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD -
SPA 30x and 50x - show miss state when call was pickup
Hello
do you know, how to show on display miss state (softkey miss) when call was pickup in pickup group.
My IP phone is SPA 303 and 502, and 922 but SPA 922 is showing miss state well.
Server is Asteriks.
MarekCall completed elsewhere has not been missed, so SPA922 is on the wrong side ...
If the line is declared as shared AND call is CANCELed with
Reason: SIP;cause=200;text="Call completed elsewhere"
then no missed call is logged.
I'm not sure if you can configure Asterisk not to use this Reason in such particular case. If I remember correctly, there is and option of Dial() Application for it ...
Of course, unless you have User->Supplementary Services->Log Missed Calls for extension in question set to "Yes" no missed calls are logged at all.
Rate useful advices and/or mark answer as "correct". It will help others to found solutions. -
Xserve raid shows power state UPS backup
How do I change the power state from UPS backup to on like the rest of the xserve raids we have? None of the xserve raids we have ever used a UPS so I do not know why this one is showing power state UPS Backup under the information tab of the GUI.
This is annoying since it's causing the circle to be yellow instead of green. Any ideas or suggestions?Never seen this. Does it help if you temporally disconnect the power cable?
-
My iphone 4s cut off and it 100% then it show low battery and no power how can i fix it
my iphone 4s cut off and it 100% then it show low battery and no power gow can i fix it
Try this Discussion
https://discussions.apple.com/message/19521062
If no joy... it looks like a trip to the Store. -
cgcontextresetctm errors on mac - shows in console and states it contributes to the degradation of the system. Any ideas?
Hi murr18140,
Welcome to the Support Communities! The article below will help you troubleshoot the issue you are having with your iPod classic not being recognized in iTunes for Windows:
iPod: Appears in Windows but not in iTunes
http://support.apple.com/kb/TS1363?viewlocale=en_US
I hope this information helps ....
- Judy -
my ipod was in recovery mode and fixed it. i can use it. but the problem is whenever am i connect it with itunes it says IPOD is in recovery mode even after recover is done. i cant sync ipod rite now. it showing same msg again. nyone knows wat to do plz??
I did the restore and it cleared and reset the iPod but after it finished the same error came up. I tried this 3 times. Also it no longer shows up as a drine in My Computer.
if it's relentlessly doing that to you, it's plausible that the message is being caused by a Windows drive letter confusion. (that's consistent with the disappearance for My Computer, too.)
see the following article for troubleshooting information on that possibility:
"iTunes has detected an iPod in recovery mode - Use iTunes to restore"
Maybe you are looking for
-
Hi, are having serious issues with my Mac Pro. Kernel panics occur on frequent basis during Final Cut Pro, but also with other processes. Trying to re-install Mac OSX on a different harddisk doesn't work. Is there anyone who knows what is happening?
-
Incorrect page orientation when rendering EPS to PDF
Hi, Using Adobe Pro 9 (tried with Adobe Pro 7 as well) trial version to convert EPS files to PDF. Was able to convert to PDF with no errors. We noticed that some of the pages within the generated PDF are oriented side ways, pages that need to be orie
-
What's wrong with my system? details inside...
hey all. i'm using the k8t Master 2 FAR board with dual opteron 940 (1.8 ghz) chips and 2 gigs ddr ram, ecc registered 266 mhz. the video card is a 256 meg ati 9600. monitor is a 17 inch samsung lcd. power supply is 400 watts. when i turn on the syst
-
How to convert string into date
Hi all, I m new to JDeveloper I m taking the date as a string then passing it as a string in the method. I want to convert tht string into the date of format (DD-MON-YYYY) or any other format require yur assistance in this job. THANKXX in advance ank
-
How to make Spry Accordion Content Panel with a variable content fit
I have a problem. The content panel has a fixed length so I changed it to auto so I can view all the content of each panel. The problem is that the content panel takes the dimensions of the longest content and applies that to ALL the panels. So as