Show sysinfo command output
Hi all ,
In our cisco 5508 WLC show sysinfo output , we are not able to see the current license level and license level on next reboot.
Any idea on why it is not showing?
Thanks,
Vijay
Hi Vijay,
Show sysinfo does not provide that information. Here is what show sysinfo provide. Probably you need to look at "show license summary" output
(WC01) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.111.5
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 7.0.112.21
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WC01
System Location.................................. ELT
System Contact................................... ICT
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.14.7.247
Last Reset....................................... Software reset
System Up Time................................... 2 days 5 hrs 11 mins 56 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +30 C
External Temperature............................. +18 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 116
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ D0:D0:FD:1F:C2:00
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 350
(WC01) >show license summary
License Store: Primary License Storage
StoreIndex: 1 Feature: base-ap-count Version: 1.0
License Type: Permanent
License State: Inactive
License Count: 250 / 0 (Active/In-use)
License Priority: Medium
License Store: Primary License Storage
StoreIndex: 2 Feature: base-ap-count Version: 1.0
License Type: Permanent
License State: Active, In Use
License Count: 350 /350 (Active/In-use)
License Priority: Medium
HTH
Rasika
**** Pls rate all useful responses ****
Similar Messages
-
"SHOW ALL" command output comes from where?
Hi,
when we give command "SHOW ALL" it gives parameter values.
actually from where it gathers this data?those are SQLPLUS settings. sqlplus is a CLIENT. it's an app, and it has it's own settings. read the SQLPLUS manual
-
Sample Command Output of show chassis inventory for CSS
Hi,
I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
Can anyone help?
Thanks in advance.
MikeHi Mchi,
When I use the command: show chassis inventory. I found :
Slot Module Serial
1 CSS5-SCM-2GE F0 JABxxxxxxx
2 CSS5-IOM-2GE E0 JAB08xxxxxx
3 CSS5-IOM-8FE F0 JAB0xxxxxxx
4 CSS503-SM-INT JAB09xxxxxxx
this is the switch fabric module that connects the other modules.
This is an internal module and it can't be removed/replaced.
Use the show chassis command to display a chassis configuration for the CSS. The syntax and options for this command are as follows:
•show chassis - Displays a summary of the chassis configuration.
•show chassis slot number - Displays the operational parameters for a slot in a CSS 11503 or CSS 11506 chassis. Enter an integer value for the chassis slot number.
•show chassis verbose - Displays detailed information about the chassis configuration.
•show chassis flash - Displays the operational and locked Flash software code on the CSS 11501, and the CSS 11503 or CSS 11506 SCM and I/O modules. An asterisk (*) character before a Flash version of code and build number indicates that it is active.
•show chassis inventory - Displays the physical configuration of the CSS including part and serial numbers.
•show chassis session-processors - Displays the weight and power summary of the session processors in the CSS chassis.
CSS11506# show chassis inventory
Chassis Inventory:
Product Name: CSS11506-2AC E0 SW Version: 07.50.1.05s
Serial Number: JAB09xxxxxx Base Mac Address: 00-13-80-37-xx-xx
Slot Module Serial
1 CSS5-SCM-2GE F0 JAB0915xxxx
2 CSS5-SCM-2GE F0 JAB0914xxxx
3 CSS5-SSL-K9 F0 JAB0848xxxx
4 CSS5-IOM-2GE E0 JAB0808xxxx
7 CSS506-SM E0 JAB0911xxxx
8 CSS506-SM E0 JAB0911xxxx
Even a "show chassis verbose" command does not indicate the presence of a GBIC. It shows the Operational Status of a port as "online" whether there is a GBIC installed or not. For example, in the output below Slot 4 has a GBIC installed in port 4/1, but 4/2 is empty:
CSS11506# sho chassis verbose
Configuration for CSS11506-2AC E0:
Product Name: CSS11506-2AC E0 SW Version: 07.50.1.05s
Serial Number: JAB0916xxxx Base Mac Address: 00-13-80-37-xx-xx
Module(s) Found: 6
Power Supplies(s) Found: 2
Fan(s) Found: 3
Slot/SubSlot Operational Locked
1/1 *07.50.1.05 07.40.1.03
2/1 *07.50.1.05 07.40.1.03
3/1 *07.50.1.05 07.40.1.03
4/1 *07.50.1.05 07.20.2.06
Slot Number: 1 Type: CSS5-SCM-2GE F0
Serial Number: JAB0915xxxx Number of Ports: 2
Operational Status: primary
Port Number: 1 Port Name: SCM-2GE
Operational Status online
Port Number: 2 Port Name: SCM-2GE
Operational Status online
Slot Number: 2 Type: CSS5-SCM-2GE F0
Serial Number: JAB0914xxxx Number of Ports: 0
Operational Status: backup
Slot Number: 3 Type: CSS5-SSL-K9 F0
Serial Number: JAB0848xxxx Number of Ports: 0
Operational Status: primary
Slot Number: 4 Type: CSS5-IOM-2GE E0
Serial Number: JAB0808xxxx Number of Ports: 2
Operational Status: primary
Port Number: 1 Port Name: IOM-2GE
Operational Status online
Port Number: 2 Port Name: IOM-2GE
Operational Status online
Slot Number: 7 Type: CSS506-SM E0
Serial Number: JAB0911xxxx Number of Ports: 0
Operational Status: powered-on
Slot Number: 8 Type: CSS506-SM E0
Serial Number: JAB0911xxxx Number of Ports: 0
Operational Status: powered-on
end of buffer.
Maybe you can use "show tech"
HTH
Sachin -
Show ip interface brief command output
Hi,
I have seen 'show ip interface brief' command output.
For some interfaces 'method' it is showing 'NVRAM' and for some interfaces it is 'Manual'.
What does it mean?
Regards
SKRhello,
what about CONFIG method. what is the difference between that and manual and how can I change it to CONFIG? this is related to the ASA 5585.
thanks!! -
Question about ACE show Conn command (tcp duration)
Hello,
I was checking connections and noticed that I would see the initial connection, but after a short time the connection quits showing up in the counters and the “show conn” command. However the user is still up and working.
This is the command I used:
sho conn serverfarm STAGING-HTTPS detail
The output shows all the connection info from source to destination, and in the ESTABLISHED state.
However, after maybe 2~3 minutes, when I up arrow I don't see any connection info. The web page is still up. If I refresh the web page, I do see the connections come in.
Can someone kindly point me to a document or provide an answer on how long should the connection be stored before they are flushed?
Config profile:
4 real servers
HTTPS protocol
Leastconn for predictor
sticky based on src/dst IP
Thanks,
RamanRaman,
If you would play with a sniffer capture, you could answer the question yourself.
If the browser loads a flash object or a java applet, once it is loaded, you can still work on the page but there is no data transfer.
with a sniffer tool you could see the browser closing the connections.
The default TCP idle timeout on ACE is 1 hour.
Gilles. -
Hi
I need to understand, what does RMAN use to read configuration info in case of No Recovery catalog.
We all know that it read from Control file about backup information.
But, when my database is in NOMOUNT mode, I connect to rman target /
Then I run show all; command.
It displays RMAN configuration, Where is this information stored?
Any idea?
Thanks in advanceHi,
Did you compare the output of the <show all ;> commands in nomount and mount (or open) mode?
In nomount you get the defaults :
RMAN configuration parameters are:
CONFIGURE RETENTION POLICY TO REDUNDANCY 1; # default
CONFIGURE BACKUP OPTIMIZATION OFF; # default
CONFIGURE DEFAULT DEVICE TYPE TO DISK; # default
CONFIGURE CONTROLFILE AUTOBACKUP OFF; # default
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO '%F'; # default
CONFIGURE DEVICE TYPE DISK PARALLELISM 1 BACKUP TYPE TO BACKUPSET; # default
CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
CONFIGURE MAXSETSIZE TO UNLIMITED; # default
CONFIGURE ENCRYPTION FOR DATABASE OFF; # default
CONFIGURE ENCRYPTION ALGORITHM 'AES128'; # default
CONFIGURE ARCHIVELOG DELETION POLICY TO NONE; # default
In mount mode you get the actual settings:
using target database control file instead of recovery catalog
RMAN configuration parameters are:
CONFIGURE RETENTION POLICY TO REDUNDANCY 1; # default
CONFIGURE BACKUP OPTIMIZATION OFF; # default
CONFIGURE DEFAULT DEVICE TYPE TO DISK; # default
CONFIGURE CONTROLFILE AUTOBACKUP ON;
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO '%F'; # default
CONFIGURE DEVICE TYPE DISK PARALLELISM 1 BACKUP TYPE TO BACKUPSET; # default
CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
CONFIGURE CHANNEL DEVICE TYPE DISK FORMAT '/backup/DB10G/%U';
CONFIGURE MAXSETSIZE TO UNLIMITED; # default
CONFIGURE ENCRYPTION FOR DATABASE OFF; # default
CONFIGURE ENCRYPTION ALGORITHM 'AES128'; # default
CONFIGURE ARCHIVELOG DELETION POLICY TO NONE; # default
CONFIGURE SNAPSHOT CONTROLFILE NAME TO '/u01/appl/ora102/product/10.2.0/dbs/snapcf_DB10G.f'; # default
Regards,
Tycho -
"Show Diag" command on 3750 IOS 12.1(19)EA1c
Hi,
I'm trying to run the "show diag" command on a 3750 with IOS 12.1(19)EA1c and the command is not recongised. I'm in enable mode and cannot find an equivalent command.
I need to do this as the Cisco Software Advisor is asking for a copy of the output.
Any pointers gladly recived.
Cheers,
GarethHi,
The tool you need is the "Feature Navigator" which can be found here:
http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
Launch the tool by selecting "Search by Feature"
Searching for "802.1x" gives a list of all those features, select "Wake on LAN support" (for example) and click add, then continue.
The platform box gives a list of all platforms that support the feature, so select 3750.
The lowest feature set is IP Base (you might have something else but worth checking this first as it's the lowest feature set)
This gives a list of about 20 versions of software which support the feature so you can see you need at least 12.2(25)SEC to get this particular feature.
The process is pretty much the same for any feature. If you know the actual command you need (in this case it's "dot1x control-direction" then you could get the same info by just looking it up in the latest command reference as that will also tell you when the feature first appeared.
Finally, if you just want a list of features for a particular release then use the same link and choose search by platform, but be aware this will be a *long* list.
HTH
Andrew. -
Hi,
Can anybody describe the following TOP Command output...
==========================================
Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie
Cpu(s): 12.0% us, 0.7% sy, 0.0% ni, 71.8% id, 15.5% wa, 0.0% hi, 0.0% si
Mem: 4147796k total, 4120904k used, 26892k free, 25708k buffers
Swap: 8191992k total, 160k used, 8191832k free, 3624432k cached
4615 root 16 0 54320 15m 5952 S 24 0.4 4:41.11 X
1915 oratest 16 0 923m 620m 485m S 20 15.3 17:09.41 oracle
1730 oratest 16 0 385m 64m 23m S 4 1.6 0:54.07 java
1912 oratest 15 0 23516 9.9m 5368 S 1 0.2 0:36.71 sqlplus
1726 oratest 16 0 385m 64m 23m S 1 1.6 0:03.35 java
1913 oratest 16 0 385m 64m 23m S 1 1.6 0:13.00 java
2135 oratest 16 0 2448 1028 760 R 1 0.0 0:00.13 top
1887 oratest 15 0 689m 23m 21m D 0 0.6 0:20.74 oracle
1 root 16 0 3468 592 504 S 0 0.0 0:01.06 init
2 root RT 0 0 0 0 S 0 0.0 0:00.04 migration/0
3 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/0
4 root RT 0 0 0 0 S 0 0.0 0:00.03 migration/1
5 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/1
6 root RT 0 0 0 0 S 0 0.0 0:00.04 migration/2
7 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/2
8 root RT 0 0 0 0 S 0 0.0 0:00.03 migration/3
9 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/3
10 root 5 -10 0 0 0 S 0 0.0 0:00.00 events/0
11 root 5 -10 0 0 0 S 0 0.0 0:00.00 events/1
12 root 5 -10 0 0 0 S 0 0.0 0:00.00 events/2
13 root 5 -10 0 0 0 S 0 0.0 0:00.00 events/3
14 root 5 -10 0 0 0 S 0 0.0 0:00.00 khelper
15 root 15 -10 0 0 0 S 0 0.0 0:00.00 kacpid
================================================
Why it is showing the Memory Free is 26 MB only...
Only one Database is running on this Machine SGA is around 600MB only.....
Why it is showing 26 MB Free of memory ....Can anybody please describe the TOP Command output.....Hi, this doest look too good... " Swap: 8191992k total, 160k used"
this means you'r using some of you'r swap, "25708k buffers" and not becouse of you'r buffers.
try using ps -ef or top ( and sort by memory by hitting "m" ) and search for the process that uses you'r memory. -
Hi all,
Can somebody ,please, clarify for me what the command "show dot11 statistics client-traffic" shows to me? The output usually looks like:
xxxx.xxxx.xxx pak in 24289 bytes in 5050182 pak out 32230 bytes out 35936358
dup 47 decrpyt err 0 mic mismatch 0 mic miss 0
tx retries 3455 data retries 3455 rts retries 0
signal strength 62 signal quality N/A
But is the units for signal strength are dBm or mW? And why the quality is N/A? What values are better ? 60 or 19 (for strength)? So if anybody can provide me with an explanation for the last 2 lines it would be great. By the way, do you know where on Cisco.com all the "show dot11" commands get explained?
Cause, additional hard to understood output is "show dot11 associations" shows MACs "not related to any ssid" (how can it be in the first place?) or shows MACs which are do associated to (the only) broadcasted SSID but the IP is 0.0.0.0? Why and what does it mean?
Thanks in advance,
Alex.First of all thank you for answering my question. On the other hand, look - this was the first place for me to go on Cisco.com. Unfortunately (and this is the very problem itself), for some odd and mysterious reasons there is no clear explanation for those commands on this or any other page on Cisco.com. In fact, the only (!) explanation for "show dot11 statistics client-traffic" is "Use the show dot 11 statistics client-traffic privileged EXEC command to display the radio client traffic statistics".
No single word about the output and it interpretation. That's strange as its sounds.
The same goes for why there are Macs which are "not associated to any SSID" in "show dot11 associations".
So, if anybody knows the answer for the previously posted questions - please post the answers. For my opinion it would be interesting for the whole community. -
Hi everyone, I'm doing a performance report, I have the output of show tech command, I'm considering the cpu and memory information for my performance report, but Im not sure about the normal operation, there is some parameter for a normal operation?, for example a router 2900, and whitch commands also I have to considering fomr my performance report?, I want a good inform for my lab, any help is welcome.
Thanks in advance.I think that you're talking about the output interpreter
https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl
cheers. -
My internal speaker no longer shows as an output option; has anyone experienced this?
My internal speaker no longer shows as an output option; has anyone encountered this before?
Hopefully one of these steps should solve the problem.
1. System Preference > Sound > Output > Internal Speakers
Highlight Internal Speakers / Headphones
Make sure Mute is not enabled.
2. Remove the headphone.
If you see red light in the headphone port, plug the headphone
in and out of the port 5 or 6 times to flip the microswitch inside.
Sound output may be stuck in the digital mode.
3. Reset PRAM. http://support.apple.com/kb/PH4405
4. Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
5. Applications > Utilities > Audio MIDI Setup
Audio Devices window
Side Bar
Click the Built-in Output.
Under Mute any of the boxes checked? If so, uncheck it.
Option click the speaker icon, if present and select Internal Speakers. -
How to copy the linux command output to the clipboard xclip is not working?
Friends,
OS: OEL 5.5
i want to copy the command output to the clipboard.
so, which rpm i have to install?
i tried with xclip rpm its not working...
xclip /etc/sysctl.conf
but its not working, not only the above command but all the commands of xclip is not working.
so, can anybody suggest me a solution?
thanksi have already tried that...
below is thru the secureCRT terminal
[root@rac1 /]# cat /etc/sysctl.conf | xclip
Error: Can't open display: (null)below is directly from the os
[root@rac1 ~]# vi tet
[root@rac1 ~]# tail -100 /var/log/messages | xclip
[root@rac1 ~]# vi test
[root@rac1 ~]# cat /etc/sysctl.conf | xclip
[root@rac1 ~]# vi test
[root@rac1 ~]# echo 'hello' | xclip
[root@rac1 ~]# vi testEdited by: OraDB on Aug 19, 2012 10:33 AM -
How to? multiline label containing exact system command output
Background info: I'm triggering a system command to display memory utilization. As you know, the "free" linux command displays many lines of text one after the other. It is similar to the mem command used in Window$.
I want to have a label displaying the command output as it is: multiple lines. Just like you see it in the console. I want to mirror whatever comes up on console after executing free from java.
Using html tags won't work out for me in this particular situation. It just doesn't do the trick. Still displays the LAST line of command output with or without html tags.
any ideas? it doesn't have to be a label. It can be anything as long as it works.
Again, as it is, it just displays the last line of the command output
//events will trigger every second
Timer t = new Timer(1000, new ActionListener(){
public void actionPerformed(ActionEvent event)
//determine memory utilization.
String cmd = "free -m";
try {
String line;
Process p = Runtime.getRuntime().exec(cmd);
BufferedReader input =
new BufferedReader
(new InputStreamReader(p.getInputStream()));
while ((line = input.readLine()) != null) {
label.setText(line);
input.close();
catch (Exception err) {
err.printStackTrace();
t.start();got it. thanks.
String cmdMem = "free -m -t -o" ;
try {
String lineMem ;
String outputMem = "" ;
Process procMem = Runtime.getRuntime ().exec ( cmdMem ) ;
BufferedReader input =
new BufferedReader
( new InputStreamReader ( procMem.getInputStream () ) ) ;
while ( ( lineMem = input.readLine () ) != null ) {
outputMem = ( lineMem + "\n" ) ;
jTextAreaSystemResourcesOutput.append ( outputMem ) ;
input.close () ;
catch ( Exception err ) {
err.printStackTrace () ;
} -
Where is the "show duplicates" command in iTunes 11?
I can't find the "show dupicates" command in iTunes 11 and I have a number I want to delete.
https://discussions.apple.com/message/20438897?ac_cid=op123456#20438897
-
Can't get computer to show volume input/output controls, Can't get computer to show volume input/output controls
How, what, why, where, when!
This is the Logic Pro forum.
We're going to need more information if this is in regards to using Logic Pro.
Computer model & year, audio interface, Logic Pro version..etc..etc
Maybe you are looking for
-
Can you delete an iCloud account but then make a new account with the same password?
Me and my mum share the same iCloud account with her email address, but I can't make my own unless I delete my mum's account that I share with her. If I delete the account, will my mum be able to make a new account with the same password? Thank you!
-
Help! Compiled help won't display
My Webhelp project was working fine until yesterday. Now, when I compile the help, I don't get an error message but when I click View Result, IE 8 can't display it! It tries a couple times and then gives up. I am using Windows XP Professional and Rob
-
CS3 Imports bad Characters from Word
Not the first time I've had to ask this... I placed a Word Doc - Remove Styles & Formatting, Retain Character Styles. Several characters have just completely fouled up. As near as I can tell, CS4 and CS2 do not experience the problem. I have highlig
-
i am unable to connect my iphone4s or ipad2 to my pc/laptop(windows7) on wi-fi on itunes. why? rbvaidya
-
Upgrade FCE from 2.0 to 3.5
When I try to upgrade my FCE 2.0 to 3.5, the installation does not allow me to upgrade the app. It will upgrade the "helper" apps but not the FCE. Version 2.0 runs well, no problem. And I'm using an AGP card (ATI Radeon 9600 Pro) on a dual G5, with p