[Solved]All wireless networks have stopped working
Connecting to wireless networks that i have previously connected to times out, both with network manager, and iwconfig.
I have tried on two networks i have previously connected to and both time out.
What is interesting is that i am able to connect if i set a static ip, but i cannot reach any addresses, not even 192.168.1.1
SOLVED:
Issue was determined to be the ath9k module, fixed it by running:
modprobe ath9k nohwcrypt=1
Last edited by seniorsassycat (2012-01-28 23:14:25)
Some news:
Networks without security works, right now i am using my tethering features for my Android phone.
I am already checking for last packages, un til now: uninstall usb_modeswitch no offers a solution (was one of the last packages with network relation), looking for more
ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 1c:75:08:21:dd:4d brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 1c:65:9d:69:fa:c1 brd ff:ff:ff:ff:ff:ff
inet 192.168.43.218/24 brd 192.168.43.255 scope global wlan0
inet6 fe80::1e65:9dff:fe69:fac1/64 scope link
valid_lft forever preferred_lft forever
iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"AndroidAP"
Mode:Managed Frequency:2.412 GHz Access Point: E0:2A:82:E6:29:06
Bit Rate=54 Mb/s Tx-Power=13 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=62/70 Signal level=-48 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:27 Invalid misc:325 Missed beacon:0
eth0 no wireless extensions.
iwlist scan
lo Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:25:86:C5:15:B
Channel:6
Frequency:2.437 GHz (Chan
Quality=50/70 Signal lev
Encryption key:on
ESSID:"4714046"
Bit Rates:1 Mb/s; 2 Mb/s;
12 Mb/s; 24 Mb/
Bit Rates:9 Mb/s; 18 Mb/s
Mode:Master
Extra:tsf=00000000ae9f498
Extra: Last beacon: 400ms
IE: Unknown: 000734373134
IE: Unknown: 010882848B96
IE: Unknown: 030106
IE: Unknown: 2A0104
IE: Unknown: 32041224606C
Cell 02 - Address: 00:25:12:F5:64:F
Channel:6
Frequency:2.437 GHz (Chan
Quality=51/70 Signal lev
Encryption key:on
ESSID:"4714046"
Bit Rates:1 Mb/s; 2 Mb/s;
9 Mb/s; 12 Mb/s
Bit Rates:24 Mb/s; 36 Mb/
Mode:Master
Extra:tsf=00000037ef592b7
Extra: Last beacon: 1036m
IE: Unknown: 000734373134
IE: Unknown: 010882848B96
IE: Unknown: 030106
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: DD950050F204104A0001101044000102103B0001031047001063041253101920061228002512F564FD1021001B5265616C74656B2053656D69636F6E647563746F7220436F72702E1023000752544C383637311024000D45562D323030362D30372D32371042000F3132333435363738393031323334371054000800060050F20400011011000A5A585631302057333030100800020086
Cell 03 - Address: E0:2A:82:E6:29:06
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=63/70 Signal level=-47 dBm
Encryption key:off
ESSID:"AndroidAP"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=0000000035539181
Extra: Last beacon: 1673ms ago
IE: Unknown: 0009416E64726F69644150
IE: Unknown: 010882848B0C12961824
IE: Unknown: 030101
IE: Unknown: 0706555320010B1B
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
eth0 Interface doesn't support scanning.
Similar Messages
-
Airport Express Wireless Network Suddenly Stops Working
Hi, I have a wireless network set up with a single airport express using WPA/WPA 2 Personal wireless security. The 5 daily clients on the network are 2 Mac laptops (Both Mac OS X.4), 2 PC's (1 Windows XP and 1 Windows Vista), and an iPhone.
Internet comes in from a Comcast connection directly into the airport express, which is set to create a wireless network and play music wirelessly using AirTunes. The Base station software is up to date, on Automatic Channel selection, and connecting to the internet using DHCP, automatic configuration and sharing a public IP address.
For some reason, every couple of weeks the airport network just stops working altogether. My Macbook Pro shows that it still has a connection with full signal to the network but has no internet connection. When I disconnect and try to reconnect, all attemps to reconnect fail. No other clients are able to get internet at this point, and I cannot even access airport settings from my Macbook Pro unless I manually reset the airport by unplugging and plugging it back in. With this reset the network starts to work again immediately and continues for several weeks again. Does anyone have any idea why it would have this random shut-off every few weeks? ThanksI have a similiar problem. Every now and then, connecting to my Airport Express network results in "there was an error joining the airport network". It appears to me that this happens at random. Usually, the problem is solved by rebooting to Windows XP using Boot Camp, connecting to the network and then rebooting to OS X.
Recently, it's become worse: the problem persist but sometimes even rebooting to Windows doesn't solve it anymore. When I try to find out what's going on using the Airport Utility, the program tells me "airport utility was unable to find any airport base stations". The only thing that helps in this case is resetting/unplugging my Airport Express and reconfiguring it.
The problems occur independently from the type of security I'm using. It's very annoying and disappointing, since my current high-end MBP has this problem and my previous mac (an iBook) never had it. -
All google apps have stopped working
Hi all.
My Z2 has has given me nothing but problems.
The latest one being that all Google apps (Play store,google +, gmail, search etc..) Have stopped working.
So I'm in a pickle.
Anyone else had this?
Solved!
Go to Solution.Clear data for those apps,remove your google account and log in again.
All we have to decide is what to do with the time that is given to us - J.R.R. Tolkien -
All my plugins have stopped working
Hi
I switched Logic Pro 9 to run in 64 bit, I opened Logic and my MacBook froze. I then manually restarted it. Now all my AU plugins wont work on Logic or GargeBand. I have even reinstalled them. WHAT DO I DO?Hi, dgroyer.
A lot of 3rd party plugins are only 32 bit. After reading peoples letters to the forum, many state that they won't run properly in 64 bit mode. Try switching back to 32 and see if that solves the problem. Good luck. I hope you solve it.
Scorpii. -
I am currently receiving the above "pop up" in the bottom tool bar.....I have contacted Microsoft, Dell support....completed three system restores, reinstalled/uninstalled drivers, etc. etc......can ANYONE help with this issue??? When I go to start, Dell wireless, etc.....this does/will NOT come up...
NORMALLY...there are two(2) icons in the bottom right hand tool bar....1=green signal bar code & 2=computer to computer conection.....the first is no longer present....this is really annoying and I wish to get corrected asap! Everything in/on the computer is working ok.....I even have INet connection!!! PLEASE ADVISE.
Dell 1721 Laptop with wireless internal card(?).......Del, after 1 1/2 hours....and no "renewal" of warranty....hung up on me.....imagine that!
Solved!
Go to Solution.After many, many hours....I finally gave in & called 800 support....
it went through four levels and finally ended at a superior tech. software/hardware
writer/installer person....took 2 minutes and he was done!
Thanks!!!
Now....as of today...#2 laptop will not work!!!!! Here I/we go again.... -
It was OK until a few days ago but now no links work in either Thunderbird or Windows Mail. I have changed nothing so I can only assume that this is another case of an update changing things without my knowledge.
Links within web pages still work. Firefox is the default browser and we have been using Windows Mail and Thunderbird (gmail and googlemail) for at least a couple of years on this computer.Open your firewall program. First check the settings. Make sure that the
program is set to tell you if a new program wants access to the web. Then
go to the list of programs the firewall has. Make sure that all the programs
you want to access the web are set to '''ALLOW'''. If it is set to '''AUTO''', the
firewall may not allow access.
This problem occurs when your Internet security program was set to trust the
previous version of Firefox, but no longer recognizes your updated version as
trusted. Now how to fix the problem: To allow Firefox to connect to the Internet
again:<BR><BR>
* Make sure your Internet security software is up-to-date (i.e. you are running the latest version)<BR><BR>
* Remove Firefox from your program's list of trusted or recognized programs, then add it back. For detailed instructions, see Configure firewalls so that Firefox can access the Internet. -
All of my apps have stopped working
I do not know if I Have changed anything but all my Apps have stopped working. When pressed they blink as though they are going to start but nothing happens - need help please
Hey it works many thanks - how clever are you. Am most grateful. Learn something new about my iPad every day
-
I have my Hp Officejet Pro 8500 A connected to my MAc Book Pro which is running Lion OS on a wireless network. It works just fine and prints and everything. The problem is a "HP Utility" window that pops up on my screen and says it is "connecting to device" and lists my printer. It just runs and runs and the entire thing is gray - meaning I can't close it, cancel it, or anything. When you try to click on it, the arrow becomes the color wheel of death. It is driving me crazy. I have gone through settings, I have downloaded the latest drivers, I have looked in utilities, I have opened the printer folder and can't find where this thing is coming from or how to turn it off. Please help. And yes I have turned offf the computer and rebooted.
If you are using Snow Leopard or Lion and have HP software for pre-Snow Leopard (either from a CD not marked as compatible with 10.6 or you recently upgraded to Snow Leopard or Lion and had the HP software on your Mac before you upgraded - even if you did a standard uninstall of the old software or installed new software over the top of it) you must uninstall the software using the 'scrubber' option:
Go to Applications/Hewlett Packard/ click on HP Uninstaller
Click on Continue
Highlight your device on the left pane
Press and hold Control + Alt + Cmd keys on the keyboard simultaneously while you click on Uninstall <<<< This IS the Scrubber Option, there is no button labeled "Scrubber"
There will be a pop up that asks if you are sure you want to uninstall ALL hp software. (At this point, if you continue, any HP printers you have installed will need to be reinstalled)
Click Continue and let it finish
Restart your Mac
Download and install this: http://support.apple.com/kb/DL907
Now reset the printing system:
- Sys Prefs, Print & Fax
- Right (control) click in the rectangle listing your printers and select Reset Printing System.
WARNING - this will delete ALL of your printers!
- Select the plus sign to re-add it. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
If you want more features, you can download and install the Full Featured software from the "Support & Drivers" button at the top of this page, otherwise, basic printing and scanning will work without it.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
FaceTime and iMessages have stopped working since i updated to 7.0.3, saying there is a network error and to try again later. Have tried reinstalling Find my iPhone to see if it works. It doesn't for me. The message says "FaceTime (iMessage) Activation: Could not sign in. Please check your network connection and try again". My network is perfectly alright as I keep buying on the App Store. can u please help out???
(A) Reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.
(B) Reset all settings
Settings>General>Reset>Reset all settings
Note: Data will not be affected but settings will be reset. -
Suddenly all of my Office-programs have stopped working and will not launch on my MacBook. They were all already installed when I bought the computer. Could anyone give an amateur from Norway a hint of what may cause the problem? (And I can not find the installation-disc for the Office Programs...Super!)
Have you contacted Microsoft support - http://www.microsoft.com/mac/support ?
-
My external speakers have stopped working. A circle with a line through it shows up when I try to adjust the volume. I have been in system prefrences to check all the sound settings and everything is set properly. What do I need to do to fix this. Help!
Though I have doubts for success, you might try a SMC reset. It can do no harm. Otherwise, barring suggestions from others, the Apple Store or qualified repair facility is the last option.
http://support.apple.com/kb/HT3964
Ciao. -
My laptop's internal speakers have stopped working since i connected my wireless beats through bluetooth. It's as if it no longer recognises any other audio output, even when i have disconnected the headphones
System Prefernces > Sound > Output
Internal Speakers selected?
"Mute" enabled? Disable it
Reset PRAM. http://support.apple.com/kb/PH4405
If this does not help, try resetting SMC.
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Best. -
All of a sudden my Embed directives have stopped working
All of a sudden my Embed directives have stopped working which is really strange. I havn't moved any of my files.
Invalid Embed directive in stylesheet - can't resolve source 'Embed("/assets/img/closeButton.png")'.
.closeBtn {
upSkin: Embed('/assets/img/closeButton.png');
overSkin: Embed('/assets/img/closeButton.png');
downSkin: Embed('/assets/img/closeButton.png');
disabledSkin: Embed('/assets/img/closeButton.png');
Could anyone shed some light on this?I tried this in the first error in the style sheet:
SuperPanel
resize-grip-skin: Embed(source="H:/flash/net/brandonmeyer/assets/images/resizeHandler.png");
etc
but I am still getting the same error -
All my apps including email have stopped working..
All my apps including email have stopped working.. and i have no idea why this happened a few days ago now and ever since ive noticed that ive no GPSR icon only 3G (sorry if i sound stupid im not very tech savy at all).
First noticed my apps not working when the normal facebook at twiter wouldnt work and then bbm messages wouldnt send and the same for emails as i havnt been reciveing any and nethier will they send.
Can anyone help with this?
Many thanks
DebbieOk it has all of a sudden came back to life!! and 50 emails came through as proof! grr!!
-
Laser Jet M1217nfwMF​P wireless and fax stopped working printer works with usb cord
I have an HP computer 64 bit version. The printer suddenly stopped working wireless, fax stopped working weeks ago. Printer does work with a usb cord. Turning it off (removing elec cord) on both computer and printer, didn't help. Nothing changed that was different to cause either problem.
Hi agueda
I see that your Laserjet M1217 wireless and fax stopped working but the usb connection does work.
I would restore the printers defaults to setup the wireless again.
Touch the setup (wrench button) on the printer, select network config, select restore defaults.
Then make sure the wireless radio is turned on.
Touch the setup button (wrench), network configuration, wireless menu, wireless radio-on.
Temporarily connect the usb cable from the printer to the computer and go to start, all programs, hp, laserjet m1217 and select wireless configuration and go through the wizard to reset up the wireless again.
or if your router has a wps button on it then you touch the wps wireless button on the printer and immediately touch the wps button on the router.
Printer should automatically connect to the wireless network.
Run the add printer wizard.
Go to control panel,(win7) devices and printers then click add a printer, next, select network
highlight printer, next, message installing printer.
Should be able to print over wireless again.
Check fax connections.
Then run a fax test.
Touch the setup (wrench button) on the printer, service, run fax test.
You should have 4 passes.
Change these fax settings on the printer.
private receive-wrench/fax setup menu/ok/fax receive setup/ok/private receive/ok/set it to off
error correction-wrench/arrow to fax setup/ok/all faxes/error correction/ok/set it to off/ok
speed-wrench/arrow to fax setup/ok/all faxes/ok/fax speed/ok//change speed to medium.
clear saved faxes-wrench/fax functions menu/clear saved faxes/ok/ok to clear.
Try sending and receiving a fax.
If you have any further issues please let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP
Maybe you are looking for
-
Error Code: -8155 I get this message even when logging on to THIS Apple Site. I even get it at times when accessing my bank or other institution where ID is required. How do I examine Certificates and determine acceptability of same - as opposed to o
-
Making jar file for the project
Hello Everybody, I have a project which has hibernate capability on and also have postgresql facility in the back-end. I have used Myeclipse to make the project which imports all the necessary libraries. Now I want to make an executable jar which wil
-
when creating a reminder in reminders(IOS5) the "add location" is not available. I am using a 3gs Thnaks
-
I have a Nikon D 50 and and confused as to whether I can open raw files with Photoshop Elements 4.0 for Mac. On the list of cameras supported there's an asterisk for Nikon. Do I need to buy the Nikon software for raw to open in PE? Here's the note fo
-
Convert table MARA -- Help Me Please!!
Hi all, I was to experiment if bapi extension works for currency field or not. As such added two fields ( one CURR other CUKY) in a Z-STRUCTURE already appended in MARA table. After experimenting, I deleted these fields from the Z-Structure and tried