[Solved] Cannot burn CD's with LG drive on new system

Arch x86_64 (up-to-date) on a Zotac GF-8200-C-E miniITX motherboard, Athlon II X2 240 CPU with an LG SATA GH22NS50 DVD+-RW drive. The drive reads CD's fine, but cannot burn anything successfully. The drive works fine on a WinXP system. I have tried burning as root with bashburn, cdrecord, and xfburn, to no avail. I have also tried changing the SATA section in my BIOS from IDE to AHCI to no avail and have tried various media. The drive has the latest firmware installed. Part of my cdrecord log is below - showing the errors:
Starting new track at sector: 0
Track 01: 1 of 520 MB written (fifo 100%) [buf 96%] 1.3x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 02 0F 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 2A 30 06 90 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 40s
write track data: error after 1079296 bytes
wodim: The current problem looks like a buffer underrun.
wodim: It looks like 'driveropts=burnfree' does not work for this drive.
wodim: Please report.
wodim: Make sure that you are root, enable DMA and check your HW/OS set up.
Writing time: 13.317s
Average write speed 268.0x.
Min drive buffer fill was 96%
Fixating...
There are both sense errors and wodim errors above. Below is relevant output from "lspci -v":
00:09.0 SATA controller: nVidia Corporation Device 0584 (rev a2) (prog-if 01 [AHCI 1.0])
Subsystem: ZOTAC International (MCO) Ltd. Device a100
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 28
I/O ports at 09f0 [size=8]
I/O ports at 0bf0 [size=4]
I/O ports at 0970 [size=8]
I/O ports at 0b70 [size=4]
I/O ports at dc00 [size=16]
Memory at fe026000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
And relevant output from "hwinfo -cdrom":
28: SCSI 100.0: 10602 CD-ROM (DVD)
[Created at block.249]
Unique ID: KD9E.Am5rv5hXfm7
Parent ID: WL76.n+8cCHqK4_3
SysFS ID: /class/block/sr0
SysFS BusID: 1:0:0:0
SysFS Device Link: /devices/pci0000:00/0000:00:09.0/host1/target1:0:0/1:0:0:0
Hardware Class: cdrom
Model: "HL-DT-ST DVDRAM GH22NS50"
Vendor: "HL-DT-ST"
Device: "DVDRAM GH22NS50"
Revision: "TN02"
Driver: "ahci", "sr"
Driver Modules: "ahci"
Device File: /dev/sr0 (/dev/sg1)
Device Files: /dev/sr0, /dev/block/11:0, /dev/scd0, /dev/disk/by-path/pci-0000:00:09.0-scsi-1:0:0:0, /dev/cd/cdrom-1:0:0:0, /dev/cd/cdrw-1:0:0:0, /dev/cd/dvd-1:0:0:0, /dev/cd/dvdrw-1:0:0:0
Device Number: block 11:0 (char 21:1)
Features: CD-R, CD-RW, DVD, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL, DVD-RAM, MRW, MRW-W
Drive status: no medium
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #14 (SATA controller)
Drive Speed: 48
And more information from "cdrecord -scanbus":
scsibus1:
1,0,0 100) 'HL-DT-ST' 'DVDRAM GH22NS50 ' 'TN02' Removable CD-ROM
1,1,0 101) *
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
Any ideas on what I can do to burn successfully with this drive would be appreciated.
Larry
Last edited by lagagnon (2010-08-11 16:35:27)

kfgz: thanks for the input. I tried your suggestion, but the burn still fails, this time with slightly different errors from cdrecord:
Performing OPC...
Sending CUE sheet...
cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 520 MB written.cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 00 50 00 00 10 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 2A 00 00 90 30 05 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 200s
write track data: error after 163840 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
Writing time: 69.338s
Average write speed 51.3x.
Fixating...
Fixating time: 0.004s
cdrecord: fifo had 133 puts and 6 gets.
cdrecord: fifo was 0 times empty and 2 times full, min fill was 96%.
??? Strange and frustrating as I have now tried so many possibilites and burned at least 15 coasters!

Similar Messages

Cannot burn data dvd with super drive

Hello together,
i try to burn a dvd in my Mac mini with superdrive using the disk-utility.
It is possible to delete a DVD +RW (fast or normal)
It is not possible to set a new name for the disk
It is not possible to burn the disk ("not enough space")
I'm logged in as admin.
What do i have to do else to burn a dvd?

Quite cool + thanks a bunch!
I still don't know (but for the moment: i don't care anyway ;-)) why it's not possible with the Disk utility, the "Help" sytem makes a lot ado about. Anyway, for the moment i'm happy again :-D
Good night from the other side of the ocean,
Joachim
MacMini 1,5GHz Mac OS X (10.4.3)

Cannot rip a cd with internal drive while burning disc with external drive

Does anyone know why I cannot access any disc with my internal superdrive while Toast Titanium 11 is burning a blu-ray movie on my external drive?
Drive that is being used to burn externally is a LG WH10LS30 model

Pretty simple. You just can't do that.

Cannot burn to DVD with iPhoto 5.0.4

Looks like I'm not the only one with this problem. I simply cannot burn my photos to DVD or CD. I was planning to make a backup copy of my summer photos and run into this problem. iPhoto starts the burning process and returns error with the DVD drive.
How much does iPhoto require free disk space on the boot volume? I currently have about 1.37 GB free. When I tried to burn I had over 2 GB free disk space.
Has anyone reported this problem to Apple yet?
By the way when I exported a couple photo albums from iPhoto it (iPhoto) flipped a couple of photos upside down. No, I didn't even touch the rotate button, the program did this on it own, none of those photos were even selected at the moment. I instally hit the revert to original button. I'm starting to get worried without current backup now. Strange things are happening...

1.37G is way too little! The system needs at least the size of the DVD as free space to burn. It's highly recommended that you have a minimum of 15% or 10G, whichever is greater, as free space to assure efficient and trouble free operation. If you get down really low and the system tries to write needed files to the HD you can trash you HD with little hope of recovery. I would do whatever it takes to get your free space up to around the recommended limit.
One way to get a little of it back is the following:
1 - run either Cache Out, OnyX or Mac Sweeper to clean out the various cache and archived log files.
2 - run Monolingual to remove the unneeded language modules. I saved 900+MB the first time I did it.
Do you have a camera that has an autorotate option? if so and it's turned on that may be the reason for the rotation issue. The 5.0.4 update corrects this but only for subsequent imports.
Hope this has been of some help. Good luck.
OT

[Solved] xorg stuck in tty1 with nouveau driver on dell xps laptop

hi all, struggling with xorg on dell xps with nouveau driver.
Nouveau works under ubuntu LTS so no hardware problem.
Followed the arch wiki for installation and all related links (nouveau, xorg etc.)
startx (and startxfce4): it seems like xserver has started but I'm stuck
in tty1 still seeing the text output of the command; ctrl-c doesn't work and I need to log into tty2 to be able to kill the xserver.
Had to create an Xorg.conf with Xorg :0 -configure (else xserver couldn't start with fatal error screen not found).
Xorg.log.0 shows no EE errors.
Tried all the tricks read on the wiki, e.g. downgraded the kernel, deleted ~/.xinitrc, deleted xorg.conf (also tried
a minimal xorg.conf with only the screen section), blacklisted modules i915 and intel_agp, checked there's no vga=
options in my bootloader. Tried some other tricks found on forum posts to no avail.
Any suggestions highly appreciated.
lspci:
http://pastebin.com/uuGEJL0D
dmesg:
http://pastebin.com/8WVPp2ZB
xorg.conf:
http://pastebin.com/SgbNX9Wn
Xorg.log.0:
http://pastebin.com/8yH2zUHq
Last edited by firippusan (2013-08-30 12:38:11)

firippusan wrote:
I don't think this possible, if you have two video cards and only want to use the nvidia, you need to have a possibility to disable the intel in your bios.
If this is not possible, then first install the intel driver, then Bumblebee and 'friends'
I overlooked that issue. It seems under ubuntu both cards are used together and it works automagically without bumblebee. I was hoping to achieve the same on arch,
given bumblebee's wiki says: "Warning: Bumblebee is still under heavy development! But your help is very welcome."
All Bumblebee is under heavy development, true, but no reason to not install it, I mean Arch is under heavy development too....
As for Ubuntu, I don't use it, and have no plans to do so, but tell me, how are they putting it together?
Just open the Bumblebee wiki, read carefully, and install it.
Take extra care with nvidia, you then need to reinstall Intel too.
Basically as advised in the install guide:
pacman -S xorg-server xorg-server-utils xorg-xinit
pacman -S xorg-twm xorg-xclock xterm
I wanted to know if you installed the Xorg group, but you did it the right way.

Cannot Adjust Screen Brightness with Fn Keys on New L540 (8.1 x64)

Hello everyone. I just purchased a new L540 with Windows 8.1 x64 on it and have run into a problem I'm seeing is apparently common. While my other Fn keys work as intended, I cannot adjust screen brightness with them. Pressing the buttons just does nothing and the laptop is running at full brightness at all times, even when on the battery. I have installed the latest Power Management Driver and from what I can tell, there is no version of the Power Management Software for anything newer than Windows 7. I also have installed the latest Hotkey driver (in fact, I've installed all the latest drivers for this machine.) I read in another thread that this can be caused by the latest HD Graphics driver from Intel but I actually can't even install that driver (says my system is not supported) so I am still using the latest Lenovo provided driver.
Can anyone please assist with this? I want to be able to quickly adjust screen brightness when on battery but I can't do that at present. Thanks!
Solved!
Go to Solution.

I have the same problem with my L540. It started with the update of the BIOS to version 1.65. Because I didn't find a solution, I went back to BIOS version 1.64, where all the brightness options are there and work properly.
You can download older versions. When on the page with the new drivers (http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS037285) go to BIOS Driver 1.65, then choose "learn more". At the end of the following page you'll see all the older versions.
That you can install version 1.64, you have to change the "Secure RollBack Prevention" Option in the BIOS: Restart the Computer. When you see the option "To interrupt normal startup, press Enter", press Enter. Press once again Enter. Press F1 to enter the BIOS Setup Utility. Choose "Security" -> then "UEFI Bios Update Option" -> then "Secure RollBack Prevention". Change this option to "Disabled". Then press F10 to save configuration changes and exit.
After restarting Windows you can install BIOS 1.64.
Another possibility is to wait for the next BIOS version ....

Office 2013 - Word cannot establish a connection with this document after the system resumed from suspend mode

Hiya!
This issue has been answered numerous times for Office 2010 and Office 2007, but I have yet to any solutions or Hotfixes that work for Office 2013 (x64) on Win7.
How to replicate the issue:
Open a file from a network share.
Edit file.
Leave computer on with file open. Computer goes to sleep or into stand-by mode.
Wait a bit
Wake up computer
CPU opens file in Read-Only mode and gives you the following error "Word cannot establish a network connection with this document after the system resumed from suspend mode. Save the document into a different file to keep any changes."
What I've tried:
http://support.microsoft.com/kb/2434898 - Office 2007 registry fixes. Does not apply.
http://support.microsoft.com/kb/2413659 - Office 2010 problem. This exact issue. Says 'No microsoft products that match this hotfix are installed'
Work Around:
I can saving new versions of these files overrides this issue, but this is sometimes not possible for end-users who only have specific access to ONE SPECIFIC FILE in a particular network share.
Please let me know how I can alleviate this issue!
Thanks
-Chris

Hi,
Are those problematic documents created via previous versions of Office?
Please also try to run a repair of your Office 2013 installtion and check if it helps. See:
http://office.microsoft.com/en-in/excel-help/repair-office-programs-HA010357402.aspx
Regards,
Steve Fan
TechNet Community Support

Ibook with CD drive only + new software on DVD = problems

The 500mhz ibook with cd drive is still going strong! I would like to move up to at least Tiger and iWork 2005 on the ibook but these titles are on DVD. I have a G5 iMac... is there anyway to connect the two machines and install software onto the ibook via the G5? Any other creative workaround suggestions are welcome!
Thanks!
Greg

Hi, Greg. Have you upgraded the hard drive, or was it a custom-build iBook with a bigger hard drive than standard? I don't really recommend installing Tiger on a 10 GB hard drive.
Our own F.J. has written an article on Installing Tiger without a DVD drive.
You may want to check it out, but if you have just a 10 GB hard drive, I'd think about it long and hard before proceeding. You need to keep about 5 GB free for Panther or Tiger to run smoothly. You are going to have to be consumed with disk maintenance if you install it on a 10 GB hard drive.

Cannot see Transaction replication with updatable subscription in new publication wizard-sqlserver 2005 standard edition

Folks,
I am planning to implement transactional replication with updatable subscription between two sql2005 Instance .I am surprised that i cold see this type of replication in the new publication wizard in the source server instead i see peer-to-peer replication.
Could you please help me in understanding how to setup transactional replication with updatable subscription in sqlserver 2005 standard edition.
Thanks.

Hi soories,
In addition to Ashwin’s post, peer-to-peer replication is available only in SQL Server 2005 Enterprise Edition. Please
execute ‘Select @@version’ in SQL Server to verify the version and edition of your SQL Server instance.
Also if you cannot see the option “Transaction replication with updatable subscription” in New Publication Wizard, you can use T-SQL to achieve this requirement.
How to: Create an Updatable Subscription to a Transactional Publication (Replication Transact-SQL Programming)
https://technet.microsoft.com/en-us/library/ms146922(v=sql.90).aspx
Thanks,
Lydia Zhang
Lydia Zhang
TechNet Community Support

[SOLVED]Cannot burn CDs

I am trying to use recorder and no matter whether I enter my path to the drive as /dev/cd or /dev/cdrom or /dev/dvd, I get errors in burning CDs
This is everything.log immediately after I put in a CD
Apr 10 17:23:11 arch kernel: sr0: Hmm, seems the drive doesn't support multisession CD's
Apr 10 17:23:11 arch kernel: cdrom: This disc doesn't have any tracks I recognize!
Apr 10 17:23:11 arch kernel: sr 0:0:1:0: [sr0] Result: hostbyte=0x00 driverbyte=0x08
Apr 10 17:23:11 arch kernel: sr 0:0:1:0: [sr0] Sense Key : 0x5 [current]
Apr 10 17:23:11 arch kernel: ILI
Apr 10 17:23:11 arch kernel: sr 0:0:1:0: [sr0] ASC=0x64 ASCQ=0x0
Apr 10 17:23:11 arch kernel: end_request: I/O error, dev sr0, sector 0
Apr 10 17:23:11 arch kernel: Buffer I/O error on device sr0, logical block 0
Apr 10 17:23:11 arch kernel: sr 0:0:1:0: [sr0] Result: hostbyte=0x00 driverbyte=0x08
Apr 10 17:23:11 arch kernel: sr 0:0:1:0: [sr0] Sense Key : 0x5 [current]
Apr 10 17:23:11 arch kernel: ILI
Apr 10 17:23:11 arch kernel: sr 0:0:1:0: [sr0] ASC=0x64 ASCQ=0x0
Apr 10 17:23:11 arch kernel: end_request: I/O error, dev sr0, sector 0
Apr 10 17:23:11 arch kernel: Buffer I/O error on device sr0, logical block 0
I have already tried it with 2 different blank CDs
Recorder gives me this error
Help appreciated !!
Last edited by Inxsible (2009-04-10 22:27:15)

Killa B wrote:
Offtopic, but your prompt is freaking awesome!
Also, this probably won't make a difference, but maybe you should use /dev/cdrw
HAHA !
I just did that a second ago and came in to update the thread. Adding /dev/cdrw does work...which is strange because I only have 1 CDRW/DVD combo drive.
and here's my PS1 if you are interested. I stole it off from the forums as well. from the thread which posts PS1. I don't remember who it was though. Credit to him/her
PROMPT_COMMAND='DIR=`pwd|sed -e "s!$HOME!~!"`; if [ ${#DIR} -gt 30 ]; then CurDir=${DIR:0:12}...${DIR:${#DIR}-15}; else CurDir=$DIR; fi'
PS1="\n╔═[$CYAN\A$WHITE]═[$CYAN\u$RED @ $BLUE\h$WHITE]\n$WHITE╚═══$GREEN=$YELLOW=$RED=$WHITE═══[$BLUE\$CurDir$WHITE]$GREEN>>$white "
Last edited by Inxsible (2009-04-10 22:26:50)

[SOLVED] Cannot open x apps with sudo

Hi all,
I just did a fresh install of kde in Arch, and I cannot open any x server apps, like kwrite, using "sudo kwrite". I tried xhost +localhost and my user name, but that didn't work. Then I tried tweaking the $DISPLAY... I couldn't get anything to happen either. Can anyone give me a few helpful pointers? Thanks!
Last edited by sunnieside-up (2011-09-20 05:56:56)

try with "sudo -E gedit"
from sudo manual:
-E The -E (preserve environment) option indicates to the
security policy that the user wishes to preserve their
existing environment variables. The security policy may
return an error if the -E option is specified and the user
does not have permission to preserve the environment.

External Burner for macbook with combo drive and IDVD 6

Hey everybody
I have been thinking of finally utilizing apples IDVD but as mentioned I have a combo drive
so my questions are these
1. What are some suggested external dvd burners for mac
2. What is the process of setting up my mac os 10.4(with latest update) for an external burner

Hi h
1. LaCie seems to be most recommended in this forum. I got a ForMac one
(old but good when copying home brewed DVDs)
2. Set-up ? Should work. Only thing that might be problematic is that using
iDVD is a hard disk space needing/consuming activity.
My goal is to at least free up 25Gb on the internal hard disk (iDVD uses only this)
after I've prepared the DVD in iDVD.
No USB/USB2 external hard disk drives - if needed use FireWire one.
Yours Bengt W

[SOLVED]Cannot move files from mounted usb drive

When I try to move a file off of my usb drive I get the following error:
mv: cannot remove ‘homework-1.txt’: Permission denied
The usb drive is mounted to a folder that I created as a normal user in my home directory. However, when I call ls -l on my home directory it says that the directory I'm using as a mount point is owned by root:
$ ls -l | grep mnt/
drwxr-xr-x 10 root root 4096 Dec 31 1969 mnt
When I unmount the flash drive, the ownership of the mount point changes back to me:
$ ls -l | grep mnt/
drwxr-xr-x 2 hugo hugo 4096 Feb 4 16:12 mnt
When I move the file I want as a super user it works but I don't get to retain ownership of the file anymore.
How can I make it so that when I mount the usb drive I have access to it as a normal user?
Last edited by Hurricane (2014-02-05 20:19:37)

Mr.Elendig wrote:
fivedigits wrote:
Seems to me that udev is giving ownership of the device to root and no write permission to world. Try adding something like:
SUBSYSTEM=="block" ID_BUS=="usb" GROUP="users" MODE=0660
to /etc/udev/rules.d/10-locale.rules
Read up on http://www.reactivated.net/writing_udev_rules.html
no, just no.
To expand on this... the rule changes permissions on all USB block devices (and will change permissions on some sysfs nodes as well), which is dangerous and doesn't accomplish what the OP wants -- to change permissions on the filesystem. You've also given the rule an irrelevant name (locale? wat?), and then point to an incredibly outdated resource (last updated nearly 6 years ago!!!) about udev rules. udev(7) is far more relevant and up to date. It doesn't mention outdated commands which no longer exist (udev$foo were all merged into udevadm).

[won't solve] cannot get chromium-libpdf with qpdfview to work

Hello!
I tried to get qpdfview working with chromium, but I didn't find out how… does someone knows how to do this?
Is it possible? I only read about people installing evince, acroread or okular but I don't really like any of them pdfreaders…
Thanks in advance for the help!
Cheers
Edit: Got the wrong AUR package for chromium-libpdf. (Can be deleted)
Last edited by domac (2012-08-12 12:31:30)

Hi, I had a similar issue with an HPC4480, I unplugged both the power & connecting cable from the printer,
rebooted my mac & then reconnected the printer, it was ok after that, check with the HP site about updates for your particular OS & drivers etc..

[Solved]Cannot copy marked region with 「M-w」 in Emacs 24.2-1

I upgraded my Emacs to version 24.2-1,and I found the default keybinding 「M-w」 cannot work,I did not rebind the key combinatory,neither change the configuration of Emacs. I searched and found nobody like me,and I didn't get information about this officially.
Could anyone give me some hints?
Last edited by tomisacat (2012-09-23 12:28:16)

jdarnold wrote:What does Ctrl-h k say the binding is for M-w?
fixed! another program bind the key.NOT Emacs's problem.

[Solved] Cannot burn CD's with LG drive on new system

Similar Messages

Maybe you are looking for