[SOLVED] HP Touchpad not detected or working with kernel 3.4.6-1

On my HP Folio 13 (https://wiki.archlinux.org/index.php/HP_Folio_13), the touchpad stopped working tonight after upgrading to kernel 3.4.6-1.
Downgrading back to 3.4.5 fixed it. I've tried AUR xf86-input-synaptics-led and the stock xf86-input-synaptics packages.
Doesn't even seem to be detected, as there's not even a mention or reference to "synaptics" in /var/log/xorg.0.log, and it's nowhere to be found under /dev/inputs/.
It isn't listed under "xinput -list" either (normally shows as "SynPS/2 Synaptics Touchpad").
Last edited by sultanoswing (2012-07-26 08:18:15)

anrxc wrote:Hello you need to rebuild synaptics-led with the new kernel if you have it installed. It replaces/overrides psmouse module in the kernel, and if it fails to load you would be left without a touchpad.
Yep that was the problem. I'd forgotten I'd compiled and installed the psmouse module using synaptics-led (/face-palm)
The AUR package, along with xf86-input-synaptics-led, did make the double-tap top-left corner hotspot work to turn the touch pad on and off. The LED light showing whether the pad is on or off never worked, however.
So - I'm now back to stock xf86-input-synaptics and on kernel 3.4.6-1 and all is working as it should.

Similar Messages

[Solved] ati-fglrx, DRI don't works with kernel 2.6.16.14-1

dmesg | grep fglrx (after start X)
[fglrx:firegl_mmap] *ERROR* No map found!
Solution : switch back to kernel 2.6.16.13-1 and wait for a fix.
pacman -U /var/cache/pacman/pkg/kernel26-2.6.16.13-1.pkg.tar.gz

the updated ati-fglrx package (8.24.8-2) solve the problem

Firefox 4 Menu Bar - When I hover over or select a menu bar item, the menu bar sub-menu becomes transparent and unreadable. Is this a known issue that can be corrected with an update or is it functionality that is not designed to work with this version?

Firefox 4 Menu Bar - When I hover over or select a menu bar item, the menu bar sub-menu becomes transparent and unreadable. Is this a known issue that can be corrected with an update or is it functionality that is not designed to work with this version?

If this happens on monitor 2 of 2, this problem has been solved here:
http://support.mozilla.com/en-US/questions/794823#answer-157988
Go to "Firefox"--> "Options" --> "Advanced"
Then un-check "Use hardware acceleration when available"
While not verified, I believe this problem is due to an SLI configuration where the focus is on monitor 1. (I.e acceleration is available, but only on monitor 1.)

Touchpad not detected after Xorg update

cat /proc/bus/input/devices:
I: Bus=0017 Vendor=0001 Product=0001 Version=0100
N: Name="Macintosh mouse button emulation"
P: Phys=
S: Sysfs=/class/input/input0
U: Uniq=
H: Handlers=mouse0 event0
B: EV=7
B: KEY=70000 0 0 0 0
B: REL=3
I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
N: Name="AT Translated Set 2 keyboard"
P: Phys=isa0060/serio0/input0
S: Sysfs=/class/input/input1
U: Uniq=
H: Handlers=kbd event1
B: EV=120013
B: KEY=800000000000 0 0 500f02102002 380307cf810d001 feffffdfffefffff ffffffffffffffff
B: MSC=10
B: LED=7
I: Bus=0019 Vendor=0000 Product=0005 Version=0000
N: Name="Lid Switch"
P: Phys=PNP0C0D/button/input0
S: Sysfs=/class/input/input2
U: Uniq=
H: Handlers=event2
B: EV=21
B: SW=1
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button (CM)"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/class/input/input3
U: Uniq=
H: Handlers=kbd event3
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button (CM)"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/class/input/input4
U: Uniq=
H: Handlers=kbd event4
B: EV=3
B: KEY=4000 0 0
I: Bus=0010 Vendor=001f Product=0001 Version=0100
N: Name="PC Speaker"
P: Phys=isa0061/input0
S: Sysfs=/class/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=40001
B: SND=6
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=/video/input0
S: Sysfs=/class/input/input6
U: Uniq=
H: Handlers=kbd event6
B: EV=3
B: KEY=3f000b00000000 0 0 0
I: Bus=0003 Vendor=0a5c Product=4502 Version=0111
N: Name="Broadcom Corp"
P: Phys=usb-0000:00:1a.0-2.2/input0
S: Sysfs=/class/input/input7
U: Uniq=
H: Handlers=kbd event7
B: EV=120013
B: KEY=1000000000007 ff800000000007ff febeffdff3cfffff fffffffffffffffe
B: MSC=10
B: LED=7
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=/video/input0
S: Sysfs=/class/input/input8
U: Uniq=
H: Handlers=kbd event8
B: EV=3
B: KEY=3f000b00000000 0 0 0
I: Bus=0003 Vendor=0a5c Product=4503 Version=0111
N: Name="Broadcom Corp"
P: Phys=usb-0000:00:1a.0-2.3/input0
S: Sysfs=/class/input/input9
U: Uniq=
H: Handlers=mouse1 event9
B: EV=17
B: KEY=70000 0 0 0 0
B: REL=3
B: MSC=10
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=/video/input0
S: Sysfs=/class/input/input10
U: Uniq=
H: Handlers=kbd event10
B: EV=3
B: KEY=3f000b00000000 0 0 0
I: Bus=0003 Vendor=05a9 Product=2640 Version=0100
N: Name="Laptop Integrated Webcam"
P: Phys=usb-0000:00:1d.7-6
S: Sysfs=/class/input/input11
U: Uniq=
H: Handlers=event11
B: EV=3
B: KEY=1 0 0 0 0
I: Bus=0011 Vendor=0002 Product=0001 Version=0000
N: Name="PS/2 Generic Mouse"
P: Phys=isa0060/serio1/input0
S: Sysfs=/class/input/input12
U: Uniq=
H: Handlers=mouse2 event12
B: EV=7
B: KEY=70000 0 0 0 0
B: REL=3

mcmillan wrote:Probably related to the xorg upgrade with hotplugging
http://wiki.archlinux.org/index.php/Xor … otplugging
If you haven't already searched the forums there seem to be a few threads going already where people are dealing with issues with this upgrade
I searched and got my keyboard and touchpad set up to work with hotplugging. Keyboard worked, touchpad did not. Any configuration changes I made dont get reconginzed. I dont know what the deal is unfortunately

The search feature in messages does not seem to work with pre IOS 7 messages

After updating to IOS 7 the search feature in the Messages app does not seem to work with messages received prior to the update. Texts received since the IOS 7 update search correctly. Is this a bug or a feature of moving to iMessages rather than just receiving standard texts?

Although not related to your question you have outdated ShockWave Flash Player go ahead and update your flash player by going to www.get.adobe.com/flashplayer
As for your problem, One of your add-ons might be the culprit too. Try running Firefox in [[Safe Mode]] with all add-ons disabled. If that solves the problem, see [[Troubleshooting extensions and themes]] and possibly [[Troubleshooting plugins]]

"This accessory is not made to work with iPhone"

I have a first generation iphone. It recently started showing a message that reads:
This accessory is not made to work with iPhone
Would you like to turn on Airplane Mode to reduce audio interference?
You will not be able to make call during this mode
YES NO
There is no accessory in the phone. Any thoughts on how to stop this behavior?
I tried reloading the OS and it didn't help.

I was having the same problem and it was draining my battery! After reading a couple of threads I was resigned to take my 1st gen iphone to the genius bar to see if they could do something. Before going to the bar I took off my pics, videos, movies, podcasts, and some applications in preparation for my visit. That night the problem stopped. This had been happening for about 3-4 weeks so I could replicate at will. After removing things from the phone when I tried to replicate the problem it would not happen. So I then started to re-sync things one at a time. After re-syncing everything but the applications I still could not replicate the problem. My feeling is that one of the applications, or combinations of, was causing the issue. I have not re-synced all the applications at this time because I am happy to have my phone back. Hope this helps.

Iphone will not charge via usb-to-computer nor via brick; I've tested with two different cables. Just before this problem arose, I got messages similar to "This accessory is not made to work with iPhone."

Most of my concern is in the subject line. I probably should've saved some content to include here. Allow me to elaborate:
While traveling with the tiny brick, I got a message on my 3GS phone that "This accessory is not made to work with iPhone”; however, the charger was working fine with another phone and with an iPad.
I tested alternatives by removing and re-inserting the cable (obviously, as I tested other devices), changing wall receptacles, shutting the phone off (all the way), all to no avail.
When I got home, I plugged a different cable--one that was connected to my iMac rather than the brick--into the my 3GS; it still didn't charge.
So, I'm hypothesizing that perhaps some debris (from a pocket?) got into the charging receptacle of the 3GS and is disrupting the connection. Perhaps there are other hypotheses.
I am reluctant to do a reset, as (a) the problem doesn't appear to be a software issue (the phone and software are all working, though the charge is declining) and (b) I don't want to lose the contents before I can sync it (now that I'm home, again).
I'd welcome suggestions. Meanwhile, I suppose I shall e-mail photos and notes from the phone to myself before I lose the remaining charge.

Try to clean the 30-pin receiver slot either by blowing air into it or using a microfiber cloth. If the problem persists, based on what you've already said, I'd say the problem is most likely hardware, and would need to be replaced or repaired. I hope your iPhone is still under the 1-Year Manufacturer Warranty, or if applicaable extended warranty. You can check by calling AppleCare National iPhone Technical Support at 1 (800) 694-7466.

Windows movie maker dose not seem to work with itunes music.

Windows movie maker dose not seem to work with itunes music anymore. Hear is what happend in a nut shell.
For reasons I can not explain I had to reinstall all my software on my Vista HP notbook. But I only had one why of saving my data music,photos. I had to use my flash drive to save everything as my DVD recoder would not work right at the time.
So I save everything I needed and then did the deed then when that was all done and everything was working right again. I put all my photos and music back to my computer. All my music or aleast most of my music is from itunes some music is from CD I do not have anymore.
My question is when I go to put music with my movie or slideshow with Windows movie maker. A box pops up and tells me that this song dose not have the right codec but it also tell me did I download the right codec. I have know idea what its talking about. Movie Maker worked fine with itunse music before the reinstall. I am thinking I did not save the music right though the music plays great on itunes but just will not import right to my movie project. I am at a lose for words can someone please help me shed some well needed light on this all the help I can get would be a God send thank you.

this happens to me too can someone please tell us what is going on?

Premiere Pro cc 2014 do not import After Effects composition. Inside Premiere Pro CC 2014 is not possible call back After Effects, is not possible to work with After Effects. Thank you

Premiere Pro cc 2014 do not import After Effects composition. Inside Premiere Pro CC 2014 is not possible call back After Effects, is not possible to work with After Effects. Thank you

You haven't given us much to go on here. What exactly are you doing and what exactly happens when you try? Which specific version of each program are you using? (Go to Help>About...)
On a side note, a simple, brief thread title is all that's needed. Something like "After Effects Issue" would be fine. You don't need the full question there.

Please Help "This accessory is not made to work with iPhone" iPod??

Hiya i wondered if someone here can help me please.
Today i went to play my ipod feature on my iPhone and it started playing on the iPhone speakers which i wanted, Then all of a sudden it stoped i checked it out and had an error message saying the following.
"This accessory is not made to work with iPhone
Do you wish to switch to aeroplane mode
YES/NO"
There is no accessory connected to the phone and also it has not been in contact with water which i heard sometimes triggers this error.
When i press the NO option the volume cuts out and the volume slider disapears on the ipod and also the volume buttons dont work.
I dont really want to factory restore it but if thats my only option then i will do it. Also i have only had the phone for less than 20 days.
Any Help/Advice is really apprieciated.

Check your iPhone's dock connector port for any dirt, lint, or foreign material, and it doesn't take much.
If clear, the standard troubleshooting steps in order are power your iPhone off and on, an iPhone reset - which is done by pressing and holding the home button and the sleep/wake or on/off button simultaneously until you see the Apple logo and then release - ignoring the slide to turn off prompt when doing so, restoring your iPhone with iTunes from your iPhone's backup, and restoring as a new iPhone or not from your iPhone's backup.
If no change after any of these steps in order, you can call AppleCare or make an appointment at an Apple store if there is one nearby.

FaceTime Camera not detected @ Google Hangout with OS X Mavericks 10.9

after i update my mac book air 2013 mid, my FaceTime Camera not detected @ Google Hangout with OS X Mavericks 10.9

ekeong wrote:
after i update my mac book air 2013 mid, my FaceTime Camera not detected @ Google Hangout with OS X Mavericks 10.9
If the problem is only with Google Hangout, take a look at FaceTime Camera not detected @ Google Hangout with OS X Mavericks 10.9 - Google Groups. You may need to wait for a google update or contact Google Support.
If ithe trouble is with other apps, too, see Apple's http://support.apple.com/kb/HT2090
(Over time, Apple has changed the built-in camera's name on newer Macs from "iSight" to "FaceTime" and then to "FaceTime HD." Regardless of the name of your Mac's built-in camera, the same info and troubleshooting applies.)
Message was edited by: EZ Jim
Mac OSX 10.8.5

I bought the external DVD player/burner for my Macbook. I tried using it with my Dell laptop but it will not work. Is it not configured to work with anything but apple operating systems?

I bought the external DVD player/burner for my Macbook. I tried using it with my Dell laptop but it will not work. Is it not configured to work with anything but apple operating systems?

If you purchased the Apple USB SuperDrive, it will only work with select Apple devices. It won't work, for example, on my Late 2011 model that has a SuperDrive built-in, but it will work with an Air, Retina model, new 'drive-less' iMacs, etc.
As far as I know, though, you can only hack the drive to work with some other Apple devices, but not with Windows PCs. Which is a shame as other, less expensive DVD/CD devices will work with just about any machine.
Sorry,
Clinton

Iphone bluetooth charging cradle--not made to work with iphone??

About every 5 minutes, my iphone pops up with a note that "this accessory is not made to work with iphone", whenever it's in the charging cradle that came with the apple bluetooth earpiece. Anybody else see this? any idea what's up? I just love the inability to get direct communication with apple on the topic.

I have the same problem. The same pop-up comes up when I plug the iPhone into the cradle that comes with the Apple-branded iPhone bluetooth headpiece. It didn't use to have this problem before, and the iPhone used to recognize the headset as also charging when both were in the cradle. Now, the headset does not even charge up when the iPhone is in the cradle at the same time!! I think the latest iPhone firmware upgrade messed up everything!! HELP!!!!

Recovery and Applications CD not configured to work with this machine.

Satellite A215-S4757
Machine trashed due to virus and want to reset to original configuration. Using disk 1 of 2 labeled RECOVERY AND APPLICATIONS/DRIVERS SATELLITE A210/215 SERIES WINDOWS VISTA HOME PREMIUM 32 BIT. When the CD boots an error is displayed. The error reads:
"This Recovery and Applications CD is not configured to work with this machine (*).
This CD is for: Satellite A215, Satellite A210
Please use the correct Recovery and Applications CD."
Can you tell me why this is not recognizing the machine correctly? Thanks for the help.
R/Jim

Satellite A215-S4757
You need the utility which resets the DMI string for that model. Call Toshiba tech support at 800-457-7777.
-Jerry

"This accessory is not made to work with the iPhone"

Makes sense right? Yes, that is if there's something plugged into it that the iPhone doesn't support. Problem is, there's NOTHING plugged into my phone. This message literally pops up every 5-10 seconds, and below the message it asks if I want to turn on airplane mode to reduce audio interference or something. Has anyone experienced this problem? I've heard of it being fixed by popping out the sim an popping it back in, didn't work - plugging in headphones an unplugging them, didn't work. Is my dock connector shorted? If that's the case I can just buy a new dock connector for $30 on ebay, take apart my phone an replace it an everything should be good then right?

oswaldswell
Posts: 1
From: Shropshire
Registered: Feb 24, 2010
Re: "This accessory is not made to work with the iPhone"
Posted: Feb 24, 2010 3:49 AM in response to: Dizzy714
I too struggled with the same problem after updating some 5-6 apps on miphone the same day i upgraded itunes software to 9.1.1(12)
lost volume from onboard speakers, volume control etc...
after deleting the updated apps one by one, rebooting after each loss I found this post(among dozens) and tried plugging in The SAME cable from my hours worth of troubleshooting,syncing only This time into the Wall plug...
Instant sound! from ipod/onboard speakers.
THANX bunches to "Oswaldswell"
not sure why or for how long...

[SOLVED] HP Touchpad not detected or working with kernel 3.4.6-1

Similar Messages

Maybe you are looking for