SPA 3102 Admin Guide

Where can I download the Admin-Guide for the Linksys SPA 3102 ?
I don't remember how many times I tried to find such a link and how many hours I spent so far with it. I could find answers to this question but the provided links were not valid anymore.
Thank you for your help.
Solved!
Go to Solution.

Finally I managed to find a working link in this forum. Why can this document not be made easier avalable? It would have been an advantage if it could have beeen found by using the search on the Cisco home-page.

Similar Messages

SPA 3102 Port Forwarding

I am seriously stumped.....I have placed my SPA 3102 between my cable modem and my apple router. I would like to forward some ports from my spa 3102 to my apple router. I've gone into the admin console and defined the settings I want on the "Application" tab. Yet there seems to be no difference when I submit all changes. The darn SPA just doesn't seem to actually forward anything. After several hours banging my head against the wall I'd greatly appreciate any assistance. Thanks, -Chris

I agree the ideal solution is one where the Sipura is behind the Apple router. In fact I had previously been in the setup with my previous Netgear router. Currently there is a bug in the Apple Time Capsule that prevents the defining of a range of ports (ie. 10000-20000) therefore I was originally unable to get the setup to work. I have managed to get the Sipura to work behind the Apple router by enabling NTP-PMP on the Apple router. I'm a little concerned about this setup as I'm not familiar with how secure this setup is. I had at one point tried to set the Apple router in the DMZ on the Sipura and it always amounted to nothing. The darn Sipura just wouldn't ever allow for ports to be forwarded. In any case, thanks for the input.

SPA 3102 backup settings

Hi I have the SPA 3102
How do I backup the settings and then restore them?????
Thanks

You can backup the SPA3102 settings by logging into the SPA3102 as Admin/Advanced and then saving the web page to your hard disk drive using your web browser (MSIE, FireFox, etc). A single save will save all the tabs under the Voice tab. Password fields are not saved. You have to do a separate save for the Router tabs.
There is a technique to modify the saved web page which will allow you to restore the web page (without the passwords). I haven't used that for awhile so I am not sure about the details.
Message Edited by hw on 10-28-2008 06:39 AM

SPA 3102 settings for axon PBX

Has anyone got the spa 3102 running with the axon pbx. If so could you post your settings?
Thanks

spec wrote:
Has anyone got the spa 3102 running with the axon pbx. If so could you post your settings?
Here is a published guide.

SPA-3102 Caller number not seen

Hi ,
french user of a SPA3102 , i use this gateway between my phone port on DSL Box and a 3cx extension. It works for all the calls incoming or outgoing.
The only problem i have is about caller number identity, what is the parameter i have to modify to have transmission in INVITE field in 3CX and know which number calls me.
For now i just obtain my default 3cx number extension or my phone line number.
I hope to be clear because my english is not enough good to explain with lots of technical details.
Waiting for ideas, Thanks in advance,
Best Regards
Profwalken

I only wish that were the case in the UK. I cannot get Caller ID working. That last PSTN caller is not shown on the spa3102 web/admin/voice/advanced page internally the last pstn called number is shown.
The last previous firmware was 3.3.6 currently the spa3102 has
Product Information
Product Name:
SPA-3102
Serial Number:
FMxxxxxxxxx
Software Version:
5.2.13(GW002)
Hardware Version:
1.4.5(a)
MAC Address:
xxxxxxxxxxxxx
Client Certificate:
Installed
Customization:
Open
I can post any config needed if someone can assist me with this. I have read about everything I can find on the web over the last few weeks and cannot find an answer to this.
I MUST STRESS THAT I AM IN THE UK so US or other solutions do not work!
Any help or assistance appreciated.
Best regards
Anthony

Receiving fax trought spa 3102 asterisk 1.4 and spa2102

I have some problem receiving fax from a pstn line trought spa3102 - asterisk and spa 2102. I have updated the firmware of the latest version for spa3102 and 2102 and I have setting the port of spa 2102 were is attached the fax machine as described in the CISCO Small Business Administration guide (page nr. 55 - using a fax machine) but i cannot receive fax at speed upper to 2400 b.
My setup is:
pstn line -> spa3102 - asterisk 1.4.29 -> spa2102.
The spa3102 is configured to pass all control to asterisk. When a call is answered and it is a fax, this call is transferd by operator to the internall extension of spa2102 where is attached the fax machine.
I don't know as configure the pstn port of spa3102 for fax receiving.
Can you help me ?
thank in adavnce.
e.

Thank you for your reply.
Ok, I report my solution because I think that can be userfull for other users.
I have resolved the problem in this manner:
1) on the SPA 3102 I have set the PSTN Line, audio section:
a) preferred codec G711u;
b) use pref. codec: YES;
c) silence supp. enable: NO;
d) echo canc enable: YES;
e) echo canc. adapt enable: YES;
f) echo sup enable: NO;
g) FAX CED Detect Enable: YES;
h) FAX CNG Detect Enable: YES;
i) FAX Passthru Codec: G711u;
j) FAX Codec Symmetric: YES;
k) FAX Passthru Method: reinvite;
l) FAX Process NSE: YES;
m) FAX Disable ECAN: no
2) on the SPA 2102 on the line were is attached the fax machine, audio section:
I have followed the setup as described in the document that I have mentioned in my first message that is:
a) Preferred Codec: G711u;
b) Use Pref Codec Only: YES
c) Silence Supp Enable: NO
d) Echo Canc Enable: NO
e) Echo Canc Adapt Enable: NO
f) Echo Supp Enable: NO
g) FAX CED Detect Enable:YES
h) FAX CNG Detect Enable: YES
i) FAX Passthru Codec: G711u
j) FAX Codec Symmetric: YES
k) FAX Passthru Method: reinvite
l) FAX Process NSE: YES
m) FAX Disable ECAN: NO
n) FAX Enable T38: NO
o) FAX Tone Detect Mode: caller or callee
With this configuration I can receive and send fax to 14.400 on PSTN line acros the asterisk and the SPA 3102 / 2102 device.
The phone attached on the line 1 port of the spa 3102 have not echo when answer or call on the PSTN line as the other phone that have access to PSTN Line.
The phone of the fax macchine have echo, but usualy is not used as phone.
E.

WRTU54G-TM/SPA-3102/Asterisk Disconnect Tone/Busy-Reorder tone?

I have a setup where I'm using the T-Mobile@Home Router (WRTU54G-TM) as a Trunk on my Asterisk system (PIAF). The WRTU54G (Phone 1 Port) is connected to the FXO (Line) port of the SPA-3102. I can making outgoing calls without any problems. However, incoming calls to my T-Mobile@home number once it hits the voicemail system on the Asterisk system and if the call hangs up before or after leaving a message, the "system" does not release the line and not do so unless I physically unplug the phone cord from either port (SPA-3102 or WRTU54G-TM). If I answer the cincoming calls and either party terminate the call, there is no disconnect issues; only when the call goes to voicemail. Is there any changes I can make to either the SPA-3102 or Asterisk, that will solve this problem/issue?
The problem seem to be related to:
a) CPC isssue and/or
b) Busy/reorder tone and/or
C) Disconnect Tones (does anyone know what the specs are for the T-Mobile system? Looks like this: 480@-30,620 @-30;4(.25/.25/1+2))
I saw on another site where an individual was able to do this:
..."Im running FreePBX on Asterisk and was able to use the busy/reorder tone by editing some lines in my zap channel config files. My solution was to simply program the PBX to detect that busy tone that T-mobile's @Home router makes after the call has ended, and use that as a signal to know when to hang up. Worked excellently, although the tail end of our voice mail message usually records a couple seconds of the busy signal... which I decided was not worth worrying about."..........
Not sure how I would implement a similar scheme, since I'm not using any ZAP channels or digium cards. Any help or suggestions welcome!

You could try to adjust this options on your SPA3102 PSTN Line. Under PSTN Disconnect Detection.
PSTN Long Silence Duration
This is minimum length of PSTN silence (or inactivity) in seconds to trigger a gateway call disconnection if <Detect Long Silence> is yes.
The default is 30.
Try to lower the values.
And Also PSTN Silence Threshold:
This parameter adjusts the sensitivity of PSTN silence detection. Choose from {very low, low, medium, high, very high}. The higher the setting, the easier to detect silence and hence easier to trigger a disconnection.
The default is medium.
Regarding for the 480@-30,620 @-30;4(.25/.25/1+2. basically this it the default settings for the US Disconnect tones. No need for you adjust.
Hope this help

SPA-3102 and Fax

Here's the problem: I am currently using a fax-switch that answers the incoming line, listens for a fax tone and, should it hear it, forwards the call to a fax machine. Without fax tone, the call is routed to the SPA-3102 and treated as voice.
This setup works nicely, but has one BIG disadvantage: All fax switches 'steal' the Caller ID. I am now trying to skip the fax-switch and use the SPA-3102 directly, by connecting the fax machine directly to the phone port of the unit. Since the SPA-3102 has the ability to recognize incoming faxes, is it able to route the call directly to the phone port? Without actually bothering the connected VOIP equipment?
I have tried to find a solution all over the Internet, but I seem to either be to blind to find anything, or, it might just not work. Thanks for your answers and suggestions.
Michaela

Thank you. I knew there must be a quick fix. Though ring thru would make the fax machine take all calls, which would make incoming phone calls be lost. If things were that easy, I wouldn't have bothered to ask. I was expecting somebody with actual Linksys knowledge to answer my question. Thanks again.

Syslog not being sent by spa-3102

I can't seem to get any syslog to come out of my spa-3102. I've enabled syslog putting the ip address in both the syslog server and the debug server in the "System" tab. I set the debug level to 3. I have my system in a "double NAT" configuration: internet -- spa-3102 -- NAT router -- LAN (incl. syslogd) I don't know how the SPA chooses which interface to send its syslog UDP to. Since my syslog server is on my LAN, I assume that I have to specify my router's external IP (assigned by the SPA-3102), and then I configured my router to forward the packets to my LAN machine running syslogd. I reconfigured my linux syslogd to accept remote syslog and to log local0 and user. Kind of complex I know, and multiple points where it could be failing. But I want the SPA in front so it can do QOS and so I don't have to worry about NAT for its SIP support. Any suggestions on what I might do.

Just responding to myself -- it seems it was some problem with my particular syslog server, nothing to do with the SPA. I set up an alternative network syslog on a different LAN machine, and it is working fine through the double NAT and forwarding of UDP 514. -mda

Where can i find the UNIX Solaris Admin guide ?

I've downloaded the distrib on edelivery (Solaris 10) but most of the admin guide to install Primavera is refering to windows commands !
I've not really time to guess which is the replacement script in unix or whatever so ....
Where can i find the Solaris version of the admin Guide ?
Thanks a lot
PS: I'm a newbie on Primavera so i'm sorry if i'm asking stupid questions ....

You can use our documentation search page found at: http://otn.oracle.com/pls/db92/db92.federated_search
I searched 'application developer' and got plenty of results for 8i.
Regards,
OTN

Remote Provisioning for SPA 3102 and PAP 2 Series

Hi,
can some one help me with SETTING up Provisioning server for SPA 3102 pap2 etc using TFTP servers (I want a detailed explanation ) please it is urgent

These urls might help:
HTTPS Based Remote Provisioning with the SPA2102, SPA3102, and SPA9000:
http://www.cisco.com/en/US/products/ps10024/products_qanda_item09186a0080a33b6a.shtml
http://www.cisco.com/en/US/docs/voice_ip_comm/csbpvga/spa3102/release/notes/SPA3102_RN_V5-2.pdf

User/Admin guide after upgrade database for recover db provided by Oracle?

Does anyone has a user/admin guide which is provided by oracle about using RMAN and how to use RMAN to RECOVER database tailor make for after upgrade database? I have been searching for a long time and don't find this document.
Anyone has this, please share.
FAN

Look in the Backup & Recovery section:
http://www.oracle.com/pls/db102/portal.portal_db?selected=4

Configuring SPA 3102 with Ooma Telo Problems

Does anyone have any experience with configuring the SPA 3102 with the Ooma Telo devise. I have been around and around on this with no luck. I have been able to get into my 3102 ip address fine, but I need a proxy server to configure the 3102 with my existing Ooma device. Ooma doesn't seem to have one to dish out. Ooma is also saying that they don't have a portal for configuring external devices to the Ooma.
Has anyone ever tried to connect the two? I'm just trying to cut my losses here and move on if this is futile.
Thanks anyone!
Duncan

Wrong forum, post in "small business voice - SPA phones". You can move your post using the actions panel on the right.

SPA-3102s back-to-back

Hello, we are trying to use two spa-3102 boxes in a back to back configuration to provide phone lines to a construction site (via a Cisco wireless bridge) like this:
(PSTN)--(SPA3102 FXO PORT)--(Wireless Bridge)--(SPA3102 FXS PORT)--(Phone/Fax)
We have voice calls passing correctly in both directions, and the phone/fax machine at the construction site is able to receive faxes most of the time, but they are unable to send outgoing faxes. When the fax machine attempts to dial, you can hear the machine pick up, dial the number, and then there is a few moments of silence followed by a fast busy signal. Any ideas?
Thanks!

EvilFetus wrote:
When the fax machine attempts to dial, you can hear the machine pick up, dial the number, and then there is a few moments of silence followed by a fast busy signal. Any ideas?
Thanks!
If the dialing waits until the interdigit timeout and then gives a fast busy it usually means that the digits dialed are not correct. If the dialing is "back-to-back" as you say, you probably are dialing some code that sends a sip uri for direct ip dialing. There are a number of variables involved.
You should be able to view the last dialed number on the INFO tab.

BPC NW Admin Guide and Office Guide Availability

Dear All,
Can Any one tell me how can I have the BPC NW Admin Guide and Office Guide ?
Please do the needful and oblige.
Regards,
Sanjay Darji

Got the helip from help.sap.com

SPA 3102 Admin Guide

Similar Messages

Maybe you are looking for