Speeding up the drawing of a letter?

I drew letter on screen and added the Write On Behavior to it. The animation spans around 300 frames. How do I speed it up so the drawing of the letter takes less frames?
Thanks.

Hi Stan-
This is pretty easy. Type Cmd-4 to bring up the layers tab, and select the Write On Behavior (not the layer it's applied to, but the actual behavior).
Look at the mini-timeline, which is right below the the canvas and layers tab. There will be a purple rectangle that says "Write On." You'll want to put your cursor over the right edge of the rectangle, click, and drag to the left to shorten the behavior. This will change the length.
For more control, Go to the inspector tab, and there are quite a lot of options for the speed. But just changing the length of the behavior is probably enough.
Good luck!

Similar Messages

Speeding up the drawing of spectrum

Dear expert,
I am using DIO 6533 board (PCI-32-HS) connected with my Optical Spectrum Analyzer to do data acquisition. Now I can get data out from the Spectrum Analyzer�s memory and drew the spectrum chart using the Labview application software. But the main problem I met is that the speed is very slow, the more data points took out, the slow the spectrum drew. It seems that the period of data abstraction time is slow. Because I have several control lines in port D, such as /Reset, /CE, /WE, etc. Which will send DIO strobe
signals in specific amount of nina second to my Optical Spectrum Analyzer. For example, I need to send an at most 40ns. digital "0" signal on the /CE line from my PC to the Optical Spectrum
Analyzer, how I can do that to satisfy the time requirement of my control lines. I know using the Labview application software can�t provide the nina seconds. Is there easier way to support this restriction? Please give me any suggestions and details on this case. Thanks a lot!

The 6533 has can be clocked to output data at 20MS/s (or 20MHz) using Pattern Generation to output data. 20 MHz will only give you control of 50ns, so 40ns timing cannot be accomplished with the 6533.
The other option would be to use a 5411 which is a function generator, but it has the ability to ouput digital data at a rate of 40MHz which would be 25ns.
You have the option to output digital data at a rate of 40MHz/n; n=integer 1....2^24-1.
The 5411 has 16-bits of digital output.
You can also use RTSI to trigger both cards at the same time if your application requires, but the 6533 will still run at a max rate of 20MHz and the 5411 at a max of 40MHz.

Hi i am currently editing clips in premiere pro cc but everytime i go to change the speed not the duration of a clip it will not let me select it - also when i go to effect controls it will not let me select time mapping? please help

Hi i am currently editing clips in premiere pro cc but everytime i go to change the speed not the duration of a clip it will not let me select it - also when i go to effect controls it will not let me select time mapping? please help

savannahp
What version of Premiere Elements and on what computer operating system?
Please review the following that I excerpted from an older post here regarding Adobe's PRE_help comments about Hollywood Effect and mention of
Red Noir. Does any of the following apply to any of what is happening to you.
- Whenever I try to add an effect from the Hollywood Looks menu, it brings up a warning that all my previous effects on that clip will be deleted. However it will let me add those same effects *after* applying Hollywood Looks.
This is because of how the Hollywood Looks are designed to be used. Since these are effect presets (multiple effects in combination) that result in a specific "look"; they are best applied in isolation. If any previous effect is applied and we still allow a Hollywood effect to be applied, we will not be able to see what the effect does clearly. For e.g. if you already have a Gaussian Blur effect applied to your clip, and then we allow you to apply the "Red Noir" Hollywood effect, the fact that the "Reds" in the scenes will be highlighted and the others converted to B/W will not be clearly seen since the content is already blurred out. So any previously applied effects was designed to be removed. This holds good even if you apply a Hollywood look "on top of" another one. The previous one will be replaced. Having said that, you can customize the look further by either tweaking an already applied filter or by adding a newer effect on top. That is the reason you can apply an effect on top of the Hollywood Effects and not vice versa.
Please review and consider and then we can proceed from there if necessary.
ATR

The speed of the "for loop iteration"

Hi all:
I have written a short mini program just to test out the speed of a "for loop iteration"
package generator;
* Title: 
* Description: 
* Copyright: Copyright (c) 2004
* Company: 
* @author not attributable
* @version 1.0
private static long tmp = 0;
public static int count=0;
public synchronized long getValue(){
 long value = 0;
 value = 10 * System.currentTimeMillis();
 if(value == tmp){
 value++;
 count++;
 tmp = value;
 return value;
public static void main(String[] args) {
 for (int i=0;i<1000;i++){
 getValue();
 System.out.println("count is " + count);
}And i find that on average, count will be a value between 498-500, which probably means that on average the speed of a for loop is around 0.5 ms. But I guess the speed of the "for loop " iteration is also very much CPU dependent, could somebody possibly give me some education on this issue :) ?
Also, anybody know exactly how System.currentTimeMillis works? For example, how does it get the current time from the OS, etc. let me know.
Again, Many many thanks...

Hi all:
I have written a short mini program just to test out the speed of a "for loop iteration"You will find the overhead of the getValue() call, the increments and most importantly the System.currentTimeMillis() is what you are timing.
 public static void main(String args[]) {
 int ITER = 1000000000;
 long start = System.currentTimeMillis();
 for(int i=0;i<ITER;i++);
 long end = System.currentTimeMillis();
 System.out.println("Iterations per sec="+ITER*1000L/(end - start));
 }Prints the following Iterations per sec=576368876Running on a 1.8 GHz Intel/Windows2000

Speeding up the footage more than 1000% but with transitions

Hey there,
I am trying to speed up the footage of a view out of an airplane window in Premiere Pro CC. I basically want to have a view over the whole landscape, let's say in a height of 300m, and then speed this view gradually up until the airplane lands, and all this within around 3-5 seconds seconds.
The first problem I have is that I seem to not be able to speed my footage up to more than 1000%. If I wanted to have a time lapse between being up in the air and landing on the runway within like 5 seconds that is definitely not enough.
The second problem is that I don't want to start the timelapse sudden, but have a transition when changing the speed. Normally, I do that with these blue little handles to get a S-curve for my speed of a certain clip. When I tried googling it considering a higher speed than 1000% someone only suggested to export the speeded clip, import it again and then speed it up again. But then there is no gradually speed up possible, it only works for the same speed over the whole clip
Summarizing these problems, I can't find a way to speed my footage up to more than 1000% without loosing the effect of a gradually S-speed-curve.
Does anyone have an advice on how to solve this problem, especially focussing on my specific clip?
Thank you and sorry for my english.
Peter

You should not have to render your captured material. If the capture settings match the sequence settings (conform this by checking item properties for both) then no rendering is necessary except for effects and filters.
Offline editing (editing in low res and capturing in full res) is not a function available in FCE.

Is there a similar function in Edge Animate that is similar to the draw path function in After Effects?

Is there a similar function in Edge Animate that is similar to the draw path function in After Effects?

No, I'm afraid not. However, you can drop a clip from in to out into the timeline and the hit CMD+R and grab the end, changing the length of the clip to fit in the space that you need by speeding up the clip.
Hope that helps.
Andy

Speed issue when drawing field of Rectangles

I'm working on a fullscreen java app that consists of a 320x320 field of randomly-colored dots, a variable percentage of which should eventually move in concert at up to 100 fps. Right now I'm simply working on drawing a varying field of dots on the screen at that speed. I'm using multiple buffers with the help of the MultiBufferTest example from Sun's Full Screen Exclusive Mode API tutorial. The demo runs great, pages flipping at what appears to be the speed at which I need my graphics to appear on the screen, but the demo draws only one Rectangle.
The problem I'm having seems to be the speed at which my 102400 Rectangles are being drawn on one of the back buffers before being flipped onto the screen. Right now I'm working with 3 buffers, but it doesn't seem to matter how many I use; the speed at which the field appears to plateau at around 1 fps. Some thoughts:
* My random color generation code is outside of the rendering loop.
* I've casted the Graphics object into a Graphics2D object g2, but that hasn't helped.
* The Rectangles are drawn inside nested for loops by row (r) and column (c) using g2.fillRect(c * mSide, r * mSide, mSide, mSide); where mSide is the side length of each Rectangle.
* Is it possible to draw all the frames into a Vector of buffers before the 'animation' begins? Presumably it would still take around 1 second to generate each frame that will appear, so that probably wouldn't work too well.
* I have the O'Reilly book Java 2D Graphics, but it doesn't help much in this situation.
I'm a novice at Java and a novice at graphics programming to boot, so is there anyone out there that can give me some advice on how to speed up the graphics generation?

I'm working on a fullscreen java app that consists of a 320x320 field of randomly-colored dots, a variable percentage of which should eventually move in concert at up to 100 fps. Right now I'm simply working on drawing a varying field of dots on the screen at that speed. I'm using multiple buffers with the help of the MultiBufferTest example from Sun's Full Screen Exclusive Mode API tutorial. The demo runs great, pages flipping at what appears to be the speed at which I need my graphics to appear on the screen, but the demo draws only one Rectangle.
The problem I'm having seems to be the speed at which my 102400 Rectangles are being drawn on one of the back buffers before being flipped onto the screen. Right now I'm working with 3 buffers, but it doesn't seem to matter how many I use; the speed at which the field appears to plateau at around 1 fps. Some thoughts:
* My random color generation code is outside of the rendering loop.
* I've casted the Graphics object into a Graphics2D object g2, but that hasn't helped.
* The Rectangles are drawn inside nested for loops by row (r) and column (c) using g2.fillRect(c * mSide, r * mSide, mSide, mSide); where mSide is the side length of each Rectangle.
* Is it possible to draw all the frames into a Vector of buffers before the 'animation' begins? Presumably it would still take around 1 second to generate each frame that will appear, so that probably wouldn't work too well.
* I have the O'Reilly book Java 2D Graphics, but it doesn't help much in this situation.
I'm a novice at Java and a novice at graphics programming to boot, so is there anyone out there that can give me some advice on how to speed up the graphics generation?

Strange download/upload speeds using the airport express as a repeater

HI,
i am having strange speed issues. Let me start off by stating my AirPort Extreme is on the middle floor of a 3 story condo. The condo has 2ft concrete slabs between floors. I have a repeater for the first floor as my signal strength was poor. I get great speeds on the same floor as the AirPort Extreme 45/15. On the 1st floor with the airport express, I get 4 down/12 up. My upload speed is always faster by a wide margin. On the 3rd floor (no repeater) I get similar results. I don't understand how my upload speeds are preserved, yet my download speeds via the repeater or 3rd are awful.
HElp! I'm using 2.4gHz for better penetration and I have changed the channels to help with congestion. Any ideas ?

Having the upload speed not change is odd indeed, but the loss of download speeds can almost invariably be attributed to the concrete walls in your condo. These do a poor job of allowing Wi-Fi signals to pass through them. Your actual Internet speeds are not affected by them, but the overall bandwidth speeds between the Internet server and your computer will be.
The best solution, albeit maybe not practical, would be to interconnect each of these base stations with an Ethernet connection and reconfigure the entire network for roaming.

Pictures in Preview Drawer...Where's the drawer???

Okay, this does it. Note to self: Buy Dummies book for operating system!
I use a lot of pictures and sort them using Preview...in the "drawer" mode, meaning that they appear in a thumbnail and I can scroll up and down to see all of the pictures.
All of a sudden, the drawer is missing and each picture opens separately. I certainly don't remember changing any preferences, etc. I did have to use Adobe Acrobat a couple times when a .pdf would not open properly in Preview. I read a couple earlier posts, so I ran Disk Utility, etc.
Can someone tell me how to get the "drawer" back. And this "Dummy" is hoping you know what I am talking about!
Geez....it's the little things in life that are so frustrating!
Thanks!
j

Hi Mickey560,
This is a bit after the fact, but I wanted to mention that this may have been a matter of just resetting the toolbar in your Preview app. I'm not sure why resetting the PRAM settings would correct the Preview drawer missing problem but it sounds more like your drawer was just hidden.
The settings held in PRAM are listed at:
http://docs.info.apple.com/article.html?artnum=2238
so I'm not sure why that would have corrected the problem (?).
When you opened Preview was the "Toolbar" for Preview visible? Was the icon for the "drawer" visible in the toolbar if the toolbar was visible? If "this" was the problem all you needed to do was go to the "View" menu (in Preview app) and select "Customize Toolbar" selection. This would allow you to drag the "Drawer" icon back to the Toolbar. Or if the Toolbar was missing you just needed to select "Show Toolbar" in the View Menu.
Sorry if that was not your original problem but just wanted to let you know if the problem ever arises again.
All's well at this point, so I guess this is moot, but just in case for your future information....
good luck,
littleshoulders

Really slow speeds during the daytime?

So i've been with BT for as long as i can remember (Broadband Option 3) and for as long as i remember it's never been that great. Not bad, but not great. Apparently i should be getting up to 8mbps but i was normally around 3mbps, which was never slow enough to bother complaining about. But in the last 2 weeks for some reason im getting extremely slow speeds during the day. From 1pm - 1am i've have around a 1mbps (if im lucky), and from 1am - pm i'll have 5 - 6mbps (which is faster than normal). Im really not sure what's going on, but it makes it impossible to do anything other than use text based websites during the day, which is a pain. Im about 250 metres away from my local exchance so i don't see why im getting 1mbps all day.
Also the wireless connection in my house is awful. My laptop that's 2 ft away from my router (BT Homehub 1 or maybe 1.5 im not sure) and it's getting a 2/5 bar signla strength. I could connect to my neighbours wifi and have a stronger signal. Addmitiedly the Home Hub is pretty wore down, so would getting the Home Hub 4 improve the wireless connection or the speeds problems? Is there any way to get it without paying £60? I mean i could switch to sky broadband, get a new router, and get a years worth of broadband for cheaper than that. The only thing keeping me with BT right now is BT sports, and i can't even any BPL games on that anymore since my connection is too slow when the games are on.
Here's the current speed (9:30 PM) http://www.speedtest.net/result/3704808533.png
I'll post the updated speed at around 2am and see how much better it is. Also any other tests/information you guys might need. Thanks.

welcome to the BT community forum where customers help customers and only BT employees are the forum mods
in order for the forum members to help please can you post the adsl stats from your router you may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or if HH4/5 then go to troubleshooting then logs and you are looking for 2 line together when hub last connected to internet and they will show your connection speed and noise margin or if netgear enter 192.168.0.1). Then run btspeedtester (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

HT1270 I own a MacBook Pro 13 inch [dec 2009] 4gb ram. I'm upgrading it to 8gb. Can I increase the speed of the ram from 1066 to 1333 Mhz..?.

I own a MacBook Pro 13 inch [dec 2009] 4gb ram. I'm upgrading it to 8gb. Can I increase the speed of the ram from 1066 to 1333 Mhz..?
Which is the best company and is it necessary to buy it from the Apple store.

Let's clear the air here between fact and fiction.
Brand of RAM has little if anything to do with its quality.
A reliable vendor is more important that brand of RAM.
Installing faster rated RAM than required for your computer doesn't result in a faster computer. The RAM still runs at the speed of the system's memory bus.
Installing slower rated RAM than required for your computer will make the computer run slower.
Using faster rated RAM is a tricky business. Sometimes it will work and sometimes it will not work. This may be due to other factors related to your computer's memory bus speed and clock speed as well as other characteristics of the RAM such as CAS Latency (CL.)
The reliable thing to do is use RAM that meets the specifications set for your computer. That information is found in either the user manual or the system specs.

When connecting wired my router straight from my internet provider I get speeds in the 90mps range. Now when connecting wired through my airport extreme I get speeds near 10mps. Also when using wireless for my ipad3 I recieve download speeds of .63mps.

When connecting, wired, to my router from my ISP I get speeds in the 90mbps range. Then when connecting, wired, to my Airport Extreme I get speeds of 10mbps. Wirelessly I get download speeds of 6mbps on my laptops and only 1mbs with my Ipad3. I am making sure only one device is sharing the network to make sure to get accurate results. Why are things so slow?

Hi Ty,
First, check with you ISP to see what speed they've promised. In my case, they indicated that the speed should be greater than 50 Mbps. If they say that it should be significantly higher than what your getting, then try the following if you're using Airport Utility v.6.:
1. Open the Airport Utility (Desktop: Command+Shift+U to open Utility Folder, select Airport Utility)
2. Click on the visual representation of the Airport Extreme and then select "Edit" (bottom right corner)
3. When the window opens (to a tab "Base Station"), click on the "Wireless" tab,
-it should have the following options: Network Mode, Wireless Network Name, Wireless Security, Wireless Password, Verify Password, a checkbox with "Enable Guest Network", and a button "Wireless Options..."]
4. Select "Wireless Options", which should open another window with the following options:
5Ghz network name, Country, a checkbox with "Create hidden Network", Radio Mode, 2.4 GHz Channel, and 5 GHz Channel [both of which can stay on "Automatic"]
5. Clicking on "Radio Mode" will bring up a list in which the las option should read:
802.11n only (5Ghz) - 802.11n only (2.4 GHz)
Once you click "Save", your router will blink amber for a little while and then it should work.
Hope this helps. Let me know if it does/doesn't.
DFLovesBikes
p.s. I apologize if the directions were excessively explicit, but I was thinking about my 73 year-old mother trying to follow them, so I erred on the side of making them more understandable. Good luck.

What is the average speed for the fans? Mine seem really slow.

What is the average speed for the fans in a MacBook Pro? When my computer is fairly idle, like right now, the fans are at roughly 1000 rpm each. Is that normal? I have seen posts where the fans are 2500-5000 rpm, so mine seem a bit low. That may explain why my computer has been getting hotter more quickly lately - this started happening after Apple replaced my logic board a few days ago.

I installed smcFanControl2 and according to that program, Apple's defaults are 2,000RPMs and the program will not let you set it any lower than that because of the increased risk of damage.
My fans are always at 2,000RPMs during normal usage, and then once I fire up a DVD or Photoshop it usually goes up to the 3,000s or so.

HI Team, Recently One week back I bought a new iphone 5 from India. They have given me a used mobile which has a different IMEI number when compared to the IMEI number present on the box. Please let me know how to proceed further

HI Team, Recently One week back I bought a new iphone 5 from India. They have given me a used mobile which has a different IMEI number when compared to the IMEI number present on the box. Please let me know how to proceed further

When you went back to the place where you purchased this phone, & asked them, what did they say?
No one here can help you with this, nor can/will Apple. You need to take this up with whoever you purchased this phone from.

Speed on the Airport Extreme

Hi I have a Macbook running Leopard. Everything runs well. Ever since I bought the Airport extreme WIFI N router my connection speed to the connected external hard drive is rather slow.....
Here is what i do....
I have a 250gig Mybook connected to the Airport extreme. On the airport utility settings, if I set it to only N wifi the speed is very slow. So i have to keep it on the multiple settings (b/g/n). According to my Macbook, when I have the multiple settings the speed is 130 mbs but if it's on only n then it's 300mbs.
So my question is, why is the connection faster when it's on multiple settings then when it's on just N?
is there a fix for this?

Leopard Ron, Welcome to the discussion area!
According to my Macbook, when I have the multiple settings the speed is 130 mbs but if it's on only n then it's 300mbs.
So my question is, why is the connection faster when it's on multiple settings then when it's on just N?
I'm confused by your question. Your first statement says that it is faster (300 Mbps) in 802.11n only. Your question seems to indicate the opposite.

Speeding up the drawing of a letter?

Similar Messages

Maybe you are looking for