Static addressing for Cisco IPSEC client

Hey Guys,
Is there a way for Cisco client based users to use static addresses instead of receivinga a dhcp address? This will be setup on a Cisco 2801 router. We usually just do dhcp but this customer is requesting static address for each user.
Thanks
Jimmy

A scalable solution would be to configure a RADIUS server and provide the client their IP address via the frame-ip-address attribute. A hack could be to have a group defined on the EasyVPN server which is associated with an IP pool that has only one address available.

Similar Messages

  • Unable to set the ip address for hosted network client after creating WIFI hotspot

    Original Title: INTERNET CONNECTIVITY PROBLEM WITH MY LAPTOP WIFI HOTSPOT
    HI all
    I am able to use internet connection from my lap hotspot, when the internet source is Public or private wifi.
    so I know the cmd window commands for hotspot and settings of client(sharing to hosted network client, assigning IP address etc.,)
    but the problem I am facing is slight different
    I am using my cdma wireless broadband datacard as my source internet connection(Reliance netconnect +)
    when I try to create hotspot for this, as usual I am able to create the hotspot and able to share the internet to hostednework client.
    but I am unable to set the ip address for hosted network client, if I try to set ip 192.169.137.1 and 255.255.255.0
    as soon as I close the window, the ip address also disappears
    when connect my android phone to that hotspot, it is able to connect but there is no internet connectivity.
    when I check the hostednetwork client for packet transmission, both sent and received packet is happening., I mean transmitting
    so what cause the failure in internet connectivity but success in hotspot connectivity?
    check the screen shots...
    can u help me..
    its little complicated

    Hi,
    Please make sure the Ad hoc connection IP adress is at the same range with your local connection. In addition, how about recreate the ad hoc connection for test, please have a try.
    If problem persists, please use Network troubleshooter in Action Center to fix this problem for test.
    Roger Lu
    TechNet Community Support

  • Cisco IPSec Client - shared key size

    Hello,
    I have got a question concerning the Cisco IPSec Client.
    Could you tell me, how large the key may be (max. 64 or 127 characters) ?
    Thanks and regards
    Patrick

    Just to help somebody else facing an issue similar to this one.
    Open Advanced menu from the configurated VPN in the Network Preferences and check 'Send all traffic over VPN connection'.
    The problem is when you have a VPN that routes all the traffic, if you want specific routes they should be configured and passed on from the router.
    I've configured a tested several vpn connections to Cisco ASA without an issue when the routes are configured on it (vpn_net1, vpn_net2 and so on) but when the route isn't specified in the router it should be considered as a default route and this option needed to be checked.

  • AAA static IP address for RA VPN Client

    Hi,
    my vpn group and VPN POOL  is locally created in Cisco VPN router but users are authenticated through ACS, AAA server via TACACS. Now I want to assign the static ip address to VPN Client. Everything is fine but due to the application problem I want to give them the static Ip address from the VPN Pool. I have greated one pool in AAA server and also configure the client in AAA to get the static ip address but unable to do this. Please help me out how to do this.
    My router is configured for TACACS+. I have checked the user configuration in AAA server to get the static ip address but it is not working. Please help me out how to do this. I cant change Router to Radius but this is my main router which is configured for 160 sites through ISDN and these sites also configured for TACACS+.
    crypto isakmp policy 10
    encr 3des
    authentication pre-share
    group 2 
    crypto isakmp client configuration group Aviation-VPN
    key egntosc
    pool aviation-pool
    acl avi-tunnel
    save-password
    netmask 255.255.255.0
    crypto isakmp profile vpnclient
       match identity group Aviation-VPN
       client authentication list default
       isakmp authorization list Aviation-authorization
       client configuration address respond
    crypto ipsec transform-set aviset esp-3des esp-sha-hmac
    crypto dynamic-map avi 10
    set transform-set aviset
    set isakmp-profile vpnclient
    reverse-route

    Since you're using ACS, I believe the way to do this is to
    go into ACS, and select the username of the user that you want
    to get the static IP. Under that user's setup, there is an option to
    always assign the same IP. Just select that and enter the IP you
    want them to get. - chris

  • Cisco IPSec Client Setup for Wireless

    I would like to set up Cisco IPSec VPN Client on a wireless Laptop to authenticate to a Cisco Radius Server 3.2. (WLC 4100)with pre-share keys.
    I have setup the basic parameters on the WLC,SSID, VLAN, L3 Security IPSec and default IPSec parameters. The WLC does not seem to send/forward any kind of request to ACS at all and when i connect on the Wireless Client it behaves as a pass through VPN.
    Thank you,

    Try these links:
    http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_example09186a008014a37c.shtml
    http://www.cisco.com/warp/public/480/acs-peap.html
    http://www.cisco.com/en/US/products/sw/secursw/ps2308/products_administration_guide_chapter09186a008015cfd8.html

  • Restrict certain IP addresses for establishing IPSec

    Is it possible on Cisco ASA 55xx to restrict (to filter) certain public IP addresses which would be THE ONLY addresses able to establish Remote Access IPSec VPN using Cisco VPN client? Let's assume that Cisco VPN client establishes VPN connection from fix public IP address (always the same).
    So, I am not talking about ACL actions on VPN traffic. I'm asking about establishing IPSec tunnel and preventing some public IPs of even trying that.
    Thanks.

    Hi Ivan,
    Yes, the "ssh 0 0 outside" overrides the control-plane ACL and allows the SSH connections to the ASA.
    Actually this statement creates  the following implicit ACL to permit the SSH traffic:
    Type: ACCESS-LIST
    Subtype:
    Result: ALLOW
    Config:
    Implicit Rule
    Additional Information:
    Forward Flow based lookup yields rule:
    in  id=0x732d57e8, priority=121, domain=permit, deny=false
            hits=1, user_data=0x0, cs_id=0x0, flags=0x0, protocol=6
            src ip/id=0.0.0.0, mask=0.0.0.0, port=0
            dst ip/id=0.0.0.0, mask=0.0.0.0, port=22, dscp=0x0
            input_ifc=outside, output_ifc=identity
    Hope this helps
    Mashal Shboul

  • A list of supported Android Phones for Cisco Jabber Client.

    Hi there,
    I opened a discussion before about the Cisco Jabber Client for Android phones.
    This product from Cisco is only official support bij a several mobile Android telephones. (very poor)
    As everyone knows is that the mobile market is continious in development. Since a half year the official support phone list is still the same, but a lot of new Adroid phones are now on the market.
    It's even so worse that some of the Cisco supported phones, are not available anymore in the market.
    - Samsung Galaxy S2 becomes a Samsung Galaxy S3
    - Samsung Galaxy TAB is still there
    - Samsung Galaxy S (are not available anymore) The S1 or S Plus are now becoming the Samsung Galaxy S Advanced.
    At what are the alternatives?
    Still the list on the documentation is out-dated.
    See:
    Samsung Galaxy S International (GT-I9000) with Android operating system (OS) Version 2.2.1 or 2.3
    Samsung Galaxy Tab International (GT-P1000) with Android 2.2.1 or 2.3
    Samsung Galaxy S II (AT&T) with Android 2.3
    To use Cisco Jabber for Android on the Samsung Galaxy S device, it is important that you upgrade your handset OS to Android Version 2.2.1 or 2.3. See the manufacturer/carrier site for more information about how to update the OS on your device. Minor voice quality issues may be experienced depending on the device used.
    So hopefully Cisco is still working on the Cisco Jabber solution, and a lot of mobile Android phones will be supported so the road to success will be open.
    Hopefully someone can help me to list of tested and supported phones (Official bij Cisco)
    Kind regards,
    Edgar

    The official list of tested Android phones is what you've already discovered.  With the next release of Cisco Jabber for Android, I'm sure it will be updated.
    While the official list of what we tested is short, the client will work on many Android devices and TAC will provide support if you run into technical issues; provided the issue is with the Cisco Jabber client itself, and not with the OS of the manufacturer.
    If there is a specific Android phone you are looking to have officially tested by Cisco, PM me with that information and I'll work with you to see what we can do to get it added.

  • Profile for Cisco IPsec VPN does not set shared secret correctly

    Hi,
    We have a shared secret configuration for a Cisco IPsec (connecting to an ASA). I can correctly configure a profile for the Cisco IPsec VPN and deliver it to the device. However, the VPN connection fails due to an invalid shared secret. If I then go into the VPN settings on the device itself and manually retype the shared secret, it works fine.
    I have noticed this when generating the mobileconfig profile both from Apple's iPhone Configuration Utility and also when using the MobileIron management platform to generate and push profiles.
    Has anyone else seen this problem? I'm really confident that I'm typing the shared secret correctly in the iPCU generated profile as I've tried it many times. It also has happened across every flavor of iOS 3.x and 4.x (including the 4.2 betas).
    thanks

    Hi,
    Thanks for the reply but it is a bit of a strange one. What makes you think the shared secret we are using - which you don't know - is more than 32 characters long. I can promise you it isn't. There's a bug in the way mobileconfig files are storing the encrypted shared secret values. I've now seen it on a third party mobile device management platform too.

  • Certificate authentication for Cisco VPN client

    I am trying to configure the cisco VPN client for certificate authentication on my ASA 5512-X. I have it setup currently for group authentication with shared pass. This works fine. But in order for you to pass pci compliance you cannot allow aggresive mode for ikev1. the only way to disable aggresive mode (and use main mode) is to use certificate authentication for the vpn client. I know that some one out there must being doing this already. I am goign round and round with this. I am missing some thing.
    I have tried as I might and all I can get are some cryptic error messages from the client and nothing on the firewall. IE failed to genterate signature, invalid remote signature id. I have tried using different signatures (one built on ASA and bought from Godaddy, and one built from Windows CA, and one self signed).
    Can some one provide the instructions on seting this up (asdm or cli). Can this even be done? I would love to just use the AnyConnect client but I believe you need licensing for that since our system states only 2 allowed. Thank you for your help.                    

    Dear Doug ,
              What is asa code your are running on ASA hardware , for cisco anyconnect you need have Code 8.0 on your hardware with cisco anyconnect essential license enabled .Paste your me show version i will help you whether you need to procure license for your hardware . By default your hardware will be shipped with any connect essential license when you have order your hardware with asa code above 8.0 .
    With Any connect essential you are allowed to use upto total VPN peers allowed based on your hardware
    1)  What is the AnyConnect Essentials License?
    The Anyconnect Essentials is a license that allows you to connect up to your 'Total VPN Peers"  platform limit with AnyConnect.  Without an AnyConnect Essentials license, you are limited to the 'SSLVPN Peers' limit on your device.  With the Anyconnect Essentials License, you can only use Anyconnect for SSL - other features such as CSD (Cisco Secure Desktop) and using the SSLVPN portal page for anything other than launching AnyConnect are restricted.
    You can see your limits for the various licensing by issuing the 'show version' command on your ASA.
    Licensed features for this platform:
    Maximum Physical Interfaces    : Unlimited
    Maximum VLANs                  : 150      
    Inside Hosts                   : Unlimited
    Failover                       : Active/Active
    VPN-DES                        : Enabled  
    VPN-3DES-AES                   : Enabled  
    Security Contexts              : 2        
    GTP/GPRS                       : Disabled 
    SSL VPN Peers                  : 2        
    Total VPN Peers                : 750      
    Shared License                 : Disabled
    AnyConnect for Mobile          : Disabled 
    AnyConnect for Cisco VPN Phone : Disabled 
    AnyConnect Essentials          : Disabled 
    Advanced Endpoint Assessment   : Disabled 
    UC Phone Proxy Sessions        : 2        
    Total UC Proxy Sessions        : 2        
    Botnet Traffic Filter          : Disabled
    Licensed features for this platform:
    Maximum Physical Interfaces    : Unlimited
    Maximum VLANs                  : 150      
    Inside Hosts                   : Unlimited
    Failover                       : Active/Active
    VPN-DES                        : Enabled  
    VPN-3DES-AES                   : Enabled  
    Security Contexts              : 2        
    GTP/GPRS                       : Disabled 
    SSL VPN Peers                  : 2        
    Total VPN Peers                : 750      
    Shared License                 : Disabled
    AnyConnect for Mobile          : Disabled 
    AnyConnect for Cisco VPN Phone : Disabled 
    AnyConnect Essentials          :  Enabled
    Advanced Endpoint Assessment   : Disabled 
    UC Phone Proxy Sessions        : 2        
    Total UC Proxy Sessions        : 2        
    Botnet Traffic Filter          : Disabled
    Any connect VPN Configuration .
    http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00808efbd2.shtml

  • How to get MAC Address for maintaning unique client id at server side?

    Hi All,
    Can somebody tell how can i get MAC id for maintaing Unique client id at server.
    or is there any alternative way to do this?
    Thanks in advance..
    CK

    Usually people just use cookies for that.

  • Friendly and static address for WSDL

    Hi,
    In NW7.1 one can see binded web service's WSDL from the SOAMANAGER.
    The resulting URL includes a GUID, that actually changes each time a new binding is done.
    I'd like to set a friendly and permanent URL for the WSDL.
    The alternate URL address only affects the SOAP call binding.
    I cannot find where to set an alternate address for the WSDL.
    Any clues?
    Thank you

    Hi Enrique,
    Use http://<hostname_>:<port>/sap/bc/bsp/sap/WebServiceBrowser/search.html, in order to browse web services on web browser. Then, select a function module and click on WSDL link on the upcoming screen. So, you can use that url in order to access wsdl.
    Best regards,
    Orkun Gedik

  • True IP address for ARD remote client via IPObserver [newbie]

    I have had success managing LAN clients via ARD, but now my situation is different.
    I want to still be able to provide ARD support via a network address specific to a workstation from outside the LAN, and the IP address I have tried does not connect. I am deriving the address from the IP Observer utility that I had my client launch on their system. [it is not the obvious 192.168.1.xxx address from DHCP]. I have confirmed that the Sharing attributes are correct on the client system, although it might be a 2.2 version [running 3.1 admin]. Based on a test, I believe the IP Observer address is the internet IP location of the router [not the actual router LAN IP], not the client.
    The IP address indicates that it is in the correct domain [Roadrunner, NYC], but the client-specific address is inaccurate. Is it because the client is setup through a DHCP router and switch? will they need a static IP? Can they somehow reveal their station-specific IP via an iChat connection log? should I try to address the client though a different port?
    I am new to this extension of ARD, so bear with the obviousness of the query to some of you.
    thx - steve

    Hi, here is what you asked me for:
    webvpn
    enable inside
    enable outside
    csd image disk0:/securedesktop-asa-3.2.1.103-k9.pkg
    svc image disk0:/anyconnect-win-2.2.0128-k9.pkg 3
    svc enable
    cache
    max-object-size 5000
    group-policy DfltGrpPolicy attributes
    dns-server value X.X.X.X
    dhcp-network-scope X.X.X.X
    vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
    default-domain value XXXXXX
    intercept-dhcp 255.255.255.XXX enable
    nac-settings value DfltGrpPolicy-nac-framework-create
    webvpn
    url-list value Lan_Applications
    svc keepalive none
    svc dpd-interval client none
    svc dpd-interval gateway none
    svc ask enable default webvpn
    customization value DfltCustomization
    tunnel-group DefaultRAGroup general-attributes
    authentication-server-group (outside) LOCAL
    authorization-server-group LOCAL
    authorization-server-group (outside) LOCAL
    dhcp-server XXX.XXX.XXX.XXX
    tunnel-group DefaultWEBVPNGroup general-attributes
    authentication-server-group (outside) LOCAL
    authorization-server-group LOCAL
    authorization-server-group (outside) LOCAL
    dhcp-server XXX.XXX.XXX.XXX
    authorization-required
    Best Regards,
    Jeyriku

  • Softphone feature for Cisco Jabber Client

    Hello everyone,
    I have a CUCM cluster v.8.6.2 and a CUPS v.8.6.4. I've installed my full CUWL licenses as well as my CUP Licenses AND the Jabber for Everyone COP file. I've managed to install Jabber on Mac and on Windows and have all the features such as Chat, Desktop phone integration and Visual Voicemail with Cisco Unity Connection working as well. The only feature I'm having a huge hassle getting to work is the Softphone feature. I've tried adding a CUPC device with the user (btw everything is integrated and uses LDAP for authentication) as the digest account for it as well as the Owner ID. I've tried adding a CSF device as well (I remember reading it somewhere) but the Jabber client never discovers a Softphone device and all of the options on the client are grayed out for me to put in the device settings. I thought I saw it once looking for a device name CSFACILLI (ACILLI being my username) in the System Diagnostics for the Jabber for Mac client but now it just shows:
       Soft Phone Server
    Server Address:           cucm02.mycompany.net
    Server Port:                     2748
    Server Protocol:           --
    Device:                               --
    Line ID:                               --
    Status:                               Disconnected
    Any help or thoughts on this would be greatly appreciated! Thanks!
    Tony

    Aaron,
    Here's the bit I found interesting from the reporting function:
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CCUCMClient::downloadConfig -- begin:
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CCUCMClient::getCnfFile -- begin: , strDeviceName.c_str()=CSFacill, bHttp=FALSE
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CTFTPClient::Get -- begin: , remotefile=CTLFile.tlv, host=cucm02.mycompany.net, bIsAsyMode=TRUE, port=69
    -- 2012-07-25 08:31:01.000 DEBUG [0xb038d000] -  TFTP_Error Select error
    -- 2012-07-25 08:31:01.000 DEBUG [0xb038d000] -  TFTP_Error Can't get packet, retrycount=3
    -- 2012-07-25 08:31:01.000 DEBUG [0xb038d000] -   CTFTPClient::ContinueGet -- end!
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CTFTPClient::Get -- end!
    -- 2012-07-25 08:31:01.000 DEBUG [0xb038d000] -  CTFTPClient::ReceiveData -- end!
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CCUCMClient::getCnfFile -- end!
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CCUCMClient::downloadConfig -- end!
    -- 2012-07-25 08:31:01.000 DEBUG [0xacab02c0] -  CPhone::setPhoneMode -- end!
    -- 2012-07-25 08:31:01.000 DEBUG [0xb030b000] -  CTFTPClient::ReceiveData -- begin: , nCookie=5, bIsAsyMode=TRUE
    It looks like it's trying to get CTLFile.tlv from my TFTP servers (which are my subscribers). I went under TFTP File Management under OS Administration on the Subscribers and no such file exists. Is this something I have to download from Cisco? It does look like it's trying for the correct device, just can't get the Configuration File it needs... Your thoughts?
    Thanks,
    Tony

  • Can AnyConnect & Cisco IPsec co-exist on client pc?

    Hi- a home user has to connect to one
    business using AnyConnect and to us using Cisco IPsec client.
    When installing AnyConnect, it wiped out the IPSec client. Can they co-exist on his pc and function side by side?
    I'm sure they can't be used simultaneously, but can't both clients be installed for very different connections?
    He's running 32-bit xp.
    Thanks.

    Kathy
    I am surprised that installation of AnyConnect removed the traditional IPSec client. I have not had that experience. I have several PCs running Windows XP SP3 which have both AnyConnect and IPSec clients installed. Either client works just fine (but not both at the same time).
    HTH
    Rick

  • Mapped drives do not open after connecting via Cisco VPN Client

    I have an issue when I initially connect to my remote network, I cannot get to any mapped drive unless I wait a few minutes for the VPN connect to mature. To explain further, I have to wait 2-4 minutes after connecting to the VPN for me to actually connect to those drives.
    The error that pops up is:
    "An error occurred while reconnecting to DriveLetter: to \\Server\sharedDrive\    Microsoft WIndows Network: The network path was not found. This connection has not been restored.
    Now, immediately after  I connect, I am able to successfully ping the server that hosts those folder locations but for some reason I cannot get to the server via UNC/shared drives until I wait a few minutes after connecting. 
    Below is the list of error logs I get when attempting to connect to the mapped drives during those first few minutes of connectivity:
    1      15:26:39.804  10/06/14  Sev=Warning/3 IKE/0xA300005F
    Firewall, Sygate Security Agent, is not running, the client will not send firewall information to concentrator.
    2      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    3      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    4      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    5      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    6      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    7      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    8      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    9      15:28:10.614  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    10     15:28:17.188  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    11     15:28:17.188  10/06/14  Sev=Warning/2 IPSEC/0xE3700003
    Function CniInjectSend() failed with an error code of 0xE4510023 (IPSecDrvCB:856)
    12     15:33:50.642  10/06/14  Sev=Warning/2 CVPND/0xA3400015
    Error with call to IpHlpApi.DLL: CheckUpVASettings: Found IPADDR entry addr=192.168.11.120, error 0
    13     15:33:51.656  10/06/14  Sev=Warning/2 CVPND/0xA3400015
    Error with call to IpHlpApi.DLL: CleanUpVASettings: Was able to delete all VA settings after all, error 0
    14     15:35:16.855  10/06/14  Sev=Warning/3 IKE/0xA300005F
    Firewall, Sygate Security Agent, is not running, the client will not send firewall information to concentrator.
    Any ideas on what it could be?

    I have a client that is showing a similar issue.. Windows 7 computer using Cisco IPSec client terminating on a Cisco 881 Router.  I can ping the server by IP, Name and even access the drive from the start menu option, but not the mapped drive.  Currently I am looking into this from a offline file issue in windows, but ran across this post and was wondering if you had figured this out?  I am going to try the following and will post back if that resolves it.
    Doing some research I found that Windows 7 and Vista both have what’s called “slow link mode”.  The behavior is that if the latency of the network connection exceeds 80 milliseconds (ms), the system will transition the files to “offline mode”.  The 80 ms value is configurable using a local group policy edit.
    Open Group policy (start -> run -> gpedit.msc)
    Expand “Computer Configuration”
    Expand “Administrative Templates”
    Expand “Network”
    Click on “Offline Files”
    Locate “Configure slow-link mode”
    This policy can either be disabled or set to a higher value for slower connections.
    https://www.conetrix.com/Blog/post/Fixing-Problem-With-Windows-7-Shared-Files-and-Mapped-Drives-Unavailable-Over-VPN.aspx

Maybe you are looking for