Status 51 regarding help

Hi,
i am getting this message please can u suggest me this help
Conditions in IDoc E1EDP05 have been transferred: Check data
Message no. VG201
Diagnosis
Condition data has been sent to the IDOC segment. This data is not automatically transferred.
Procedure
Check the incoming data and, if necessary, copy it into the document manually.
Regarding
anil

Hi,
Is your message type COND_A?
~ Bineah.

Similar Messages

How To display our Z*status in Crm_dno_monitor under Status Field -F4 help

Hi,
In Crm_dno_monitor transaction - on the Selection screen Status field comes , Now in that status Field F4 Help Shows the Standard status only, For Ex: Open, Super user,....ect,.
Now I want to display the our Z status* in that F4 help of that status Field in that particular Crm_dno_monitor transaction.
Let me know how it's possible,
Thanks,
Nirmal

Dear Saxena,
Thank's to Response,
We used our own Zstatus profile, So we want our Zstatus profile - status in F4 help in status field. Ex: we are using the Zstat status profile and we want to display Zstat status in status field by F4 help but now it shows the standard status only.
Thanks & Regards,
Nirmal
Edited by: Nirmal R on Feb 28, 2008 7:57 AM
Edited by: Nirmal R on Feb 28, 2008 7:58 AM

How To change the status in Crm_dno_monitor under Status Field -F4 help

In Crm_dno_monitor transaction - on the Selection screen Status field comes , Now in that status Field F4 Help Shows the Standard status only, For Ex: Open, Super user,....ect,.
Now I want to display the our Z status in that F4 help of that status Field in that particular Crm_dno_monitor transaction.
please help it out .
Thanks,
Deepak Saini

thanks a lot dear frnd,
In crm_dno_monitor
how can i find that staus field ,currently using which status profile-statuses.how can i replace our status profile statuses in place of standard status profile-statuses.
(in crm_dno_monitor
just check for the field status profile and provide your status profile name.) - i did not got that point.
please give me the clear explanation.
Thanks and Regards ,
Deepak

My ipod touchs location services has stopped working. I just installed a new modem to my pc could that be the problem and how to fix ? ive already reset the ipod to new status and no help. thank for any help

my ipod touch has lost location services after i installed a new modem to my pc . it is turned on in the settings and i have even reset the ipod to new status. Any help would be appreciated thanks.

Nothing you can do except wait until Apple adds the router to their database of routers and their location. If you or someone nearby does not have an iPhone it can take a while. There is no way to tell Apple to add a router to their database.
iOS 5: Understanding Location Services

Business transaction control in status schema regarding date determination

Hi all,
is there a business transaction in the status schema that can control the date determination ?
My problem is that the dates are redetermined every time I change status. I can't set the flag "Determine date only once" in the date profile because I wan't the dates to be re-determined when I change the priority. But not when changing the status. How is that controlled ?
Best regards
Annette

Hi Anette,
ITS not possible to control the date determination with standard customizing. Its the event handler CRMV_EVENT that triggers the date determination on change of status. Functions CRM_DATES_RESET_CALENDAR_EC and CRM_DATES_ACTUALDATE_SET_EC are defined for object name STATUS on Event AFTER_CHANGE. You would need to modify this to change the standard functionality.
Hope this helps.
Kind regards,
Vanessa

S.M.A.R.T. Status: Failing, Please Help...

About a week ago my iMac G5 froze. I had to unplug it from the wall to restart it, and when I did I got the "?" folder meaning it couldn't find a startup disk. I then ran the disk utility from the Tiger install disk and that froze halfway through also. Now the utility says that the drive has reported a fatal hardware error and the S.M.A.R.T. status is failing. I can't do anything with my 6 month old computer, which is no longer covered by warranty. Any help or suggestions would be much appreciated.

Ouch doesn't sound good, sounds expensive. You can if I'm not mistaken still purchase Apple Care and I thought it was a 1 year warrantee with 90 days phone support. Bob :~)
PRODUCT WARRANTY
All Apple hardware products, including clearance and refurbished products, carry a one-year Limited Warranty against defects in materials and workmanship. You may review a copy of the Limited Warranty on new products, including its limitations and exclusions, before you purchase.

Regarding help to identify errors in 10g xe

Hi,
plz help , how to identify the error code in sql command line (like ORA-04030).

Hi,
This might help
http://download.oracle.com/docs/cd/B25329_01/doc/admin.102/b25107/memory.htm#BGBFCHGI
Regards,
Jari

Regarding Help File

Hi All,
I used the following code for showing the help of user form. Means when i run user form through .Net it shows in SAP and when i will press F1 then it shows help of that user form. It works fine.
But in my .CHM help file i have two or more form information in that file. I want suppose i wil open first form i want display help of that perticular form from that file and when i wil open second i want to desplay help of second form from that file. How i show help of perticular form from .CHM file.
If pVal.MenuUID = "275" And pVal.BeforeAction = True Then
                If SBO_Application.Forms.ActiveForm.TypeEx = "ChkRdo" Then
                    Dim psi As New ProcessStartInfo()
                    psi.UseShellExecute = True
                    psi.FileName = "C:\Documents and Settings\Harish Patil\Desktop\Checkbox and Option button\ChkOpt\ChkOpt\New HTML Help.chm"
                    Process.Start(psi)
                    BubbleEvent = False
                End If
            End If
Thanks and Regards,

check call specfic file in CHM file
The trick is load the chm file with parameters.

Regarding help for merep_sbuilder and merep_mon transactions

Hi,
Where do I get help for the MI related transactions in SAP WAS like merep_sbuilder and merep_mon
I want help documentaion to make out the log shown in merep_mon.
There are also lot of options while enabling the syncbo like push etc. What is the significance of these options.
Do suggest where I can find proper documentation for the above
Regards
Raja Sekhar

Hi Raja,
just go through this troubleshooting guide for smart synchronizations.
http://sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/909d75c3-0801-0010-5f92-920a78c53daa
from this document , u will get a clear picture on merep_mon and transactions for troubleshooting .
just refer this Installations document also ..
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/mi/best practices for sap mobile engine 2.5/bblibrary/documentation/mi25_installation_guide.pdf
<<
There are also lot of options while enabling the syncbo like push etc. What is the significance of these options
>>
r u talking about the mass data upload in the case of T01 n t51 SyncBos.?. make it clear.
Regards
Kishor Gopinathan

Regarding help on sap

How should i go about finding path for particular topic on help.sap.com
for instance if i want screen painter i go for path http://help.sap.com/saphelp_erp2005vp/helpdata/en/d1/801c61454211d189710000e8322d00/frameset.htm
similarly if i want to know about different path how to go about finding the path.
Regards.
Edited by: chidambar dixit on Jan 1, 2008 4:55 PM

http://www.easymarketplace.de/online-pdfs.php
http://help.sap.com/saphelp_erp2004/helpdata/en/35/2cd77bd7705394e10000009b387c12/frameset.htm
http://www.sapabaplive.blogspot.com/
>award points if helpful

Regarding help for selecting module in SAP

Dear Sir,
Myself manish kumar singh still working as an enduser in SD & PP (R/3) module.But now i want to select one module from both of them. But i confuesed for selecting one. I am graduate from commerce side and now persuing MBA. I am working in Excsie deptt. Pls help me for selecting the module and also pls guide me the good institutes for coaching which is chepest and also located in delhi.

Hi Manish,
As in my view PP will be good one.
Regarding SAP training centers, check the below list of all the SAP Authoried training centers where from you can pursue the course:
http://www.sap.com/asia/services/education/centres/partners.epx
Regards,
Subhasha

I can not clean status yahoo, who help me

i hope some one help me

what do you mean "I can not clean status yahoo"? That doesn't make sense in English.

Gigabit interface status faulty please help

When I do a show interface status on 4500 switch I got a status faulty
I did never see such thing
Port- Name-Status-Vlan-Duplex-Speed Type
Gi2/7-jsh3 faulty 188 full XXBaseSX
Could you please help?
Thanks a lot

this usually indicates the port is faulty (bad; not working; will not work)
this may have been set via the POST of the device. the internal tests failed and the port was marked FAULTY.
this could also be the result of a good port simply went bad for some unknown reason.
try to disable/reEnable the port. will probably still say faulty. (cannot initialize a faulty port)
try to reset the blade the port is on, or the supervisor if it resides on that.
do a "show test" (catOS) to see what the POST found when it did its powerOnSelfTests.
i've seen plenty of FAULTY ports and 99% of the time, the port is simply bad and must be replaced. (usually an ASIC or the likes)

Regarding Help File *F1*

Dear Experts,
I have Facing Problem while pressing "F1"
The following error massage comes
Navigation to the webpage was canceled
What you can try:
Retype the address.
Thanks & Regard
Nishikant S Virkhare

HI
Check that you can access the help file. If it has not worked before you will need to doenload it. You may choose to have a help file per client of a shared help file.
This can be set from the B1 Client under Help pulldown menu / Document settings.
There are lots of config issues that can come in to play, especially windows permissions
You should search the forum as this will have been posted many times before.
Peter

Clarification regarding " " & "" - Help

The below code produces
$ java t103
Hello World!
HelloWorld!
is there any logical or any difference in using the two ways of declaring c and cc, because in one of the program that I was writing i was figuring out the problem for a long time and this was issue. I figure out the problem and solved it, but was not sure the actual reason for such a behavior by java. Could somebody help me please.
class t103
     public static void main(String[] args)
          String c = " ";
          String cc = "";
          System.out.println("Hello" + c + "World!");
          System.out.println("Hello" + cc + "World!");
}

I dont know it was kind of strange to me also, I also knew that the cc is length of zero and c is one. But then why did the behavior of the program change by changing this. Meaning when I used c it never worked and when I used cc it worked perfectly fine.
This is the code snippet, When I declared charSequence " " with a space it never got passed through the for loop that I have mentioned and when I changed it to "" it works fine. So it was not clear to me why it worked when I changed it.
String charSequence = "";
          charSequence += theBoard [ r ] [ c ];
                  for( int i = r, j = c;
                 i >= 0 && j >= 0 && i < x && j < y;
                 i += z, j += a )
/code]

Status 51 regarding help

Similar Messages

Maybe you are looking for