Strange high low frequencyy sound in solaris 11 usb live

Hi,
When I boot Solaris 11 (fresh usb image from oracle.com/technetwork/server-storage/solaris11/downloads/index.html Download LiveUSB (985 MB) ) and just after screen where I can choose keyboard strange high frequency sound starts to increase and decrease. I searched on internet and the problem is mostly about fan (http://www.tomshardware.co.uk/forum/282076-10-high-pitch-noise) and CPU.
The problem is that laptop (http://www.dell.com/hr/p/inspiron-15r-n5110/pd) is working just fine on windows and ubuntu (not so much heating and that sound) . So does anybody knows whats the problem because this is something new in my computer xp and I would like to know what component can actually reproduce that strange high low frequencyy sound

The easiest solution is the best in most cases

Similar Messages

High-Low Alarm on KT4V

Just got a KT4V motherboard, with Athlon XP2100, 256MB PC2700 SDRAM.
Everything runs fine for an hour or so, and then the PC abruptly turns off accompanied by a high/ low alarm sound which continues until I unplug from mains and restart.
I am assuming this is a high temp shut down, but can find no mention of it in the manual/ website to confirm this, and the temp monitor is reporting only 40 degrees.
Any one got any suggestions?

Thanks for your thoughts.
I checked the cooler, which was located correctly (hopefully gone passed that level of mistake now), but noticed, as I picked up the PC to have a look, it truned off again with the alarm going.
Rebooted, tapped the PC on the top, alarm goes of. Does the motherboard have a state of the art anti theft movement sensor built into it? I was beginning to think to myself.
So, rebuilt PC thinking stay screw got under the motherboard causing it to short or that sort of thing, but same problems afterwards, so I replaced the power supply and now everything is working OK.
Stange thing is though, the power supply works fine in another PC with similar spec (but non-MSI) motherboard, no mattger how hard you bang it!
Thanks for help anyway.

My iPad makes a high low high tune every fifteen to twenty minutes, anyone know of this and have a fix for this annoying sound.

My iPad makes a high low high tune every fifteen to twenty minutes, anyone know of this and have a fix for this annoying sound.

I Also have this problem!!
In my situation, the screen simply started exhibiting the same symptoms a few weeks ago (early February) for no apparent reason. At first I thought the screen was dead, but discovered the heat solution by accident. Now I turn it on and keep it from going to sleep until I go to bed. Thank goodness the battery is still awesome on this thing.
I bought it new and still has the original screen, I keep it at home (never below 62 degrees). Coincidentally, this happened a day or two after the expiration of the warranty!! Any help figuring this one out would be eternally appreciated.
iPad mini retina Wi-Fi, iOS 8.1.3

Random 3 note tone, low high mid tone sound in succession.

Hi All,
Occasionally I get a three tone sound from my MBP. It sounds like something you would hear on a station with a low high mid tone sound in succession. As it is too random it is hard to capture using opensnoop and filemon.
Thanks, Dave.

If you are running Skype, it could be alerts that contacts are available. You can turn the off in Skype/Preferences.

Sound Quality from usb connector bad

serial connection/usb connection does not give good sound quality although connections through headphone jack is perfect. How can this be fixed?

Am i understanding your problem correctly, it sounds (haha! No pun intended!) like the earphones are not able to handle the highs & lows of these songs and basically you're overloading them causing the crackling noise.
Are you using the earphones/buds that came with your iPod? If so, that could be why the song sounds good on your external speakers, but not through your earbuds.
Hope that helps

Changing OSX default volume setting to a higher level in sound preferences

When I change the default volume setting to a higher level in sound preferences within OSX, it is back at the lower level at the next listening session the following time I use iTunes on my Mac Mini. Within System Preferences there is a section that lets you "choose a device for sound output" but the only choice I have is "line-out" and under the "port" heading there is only "built-in output"--no other choices are shown. I have external speakers attached which I like to use for listening to music as I work. What is the problem? Why won't the higher volume I set remain? Also, shouldn't more than one choice be shown for sound output?

This sounds like the problem that I'm experiencing and <a href-"http://discussions.apple.com/message.jspa?messageID=2694517#2694517">aske d about a couple of days ago. The sound level resets to 50% after shutdown.
I tried setting the levels in Audio MIDI Set Up as suggested above, but that hasn't changed anything.
In answer to B_web, I am running my external speakers through the headphone jack.
So, any other suggestions?

High low chimes..?

My Imac makes high low chimes when it's off and when I don't touch anything,the sound takes about 4/5sec..,anyone any idea what he's trying to say..?
The sounds repeats maybe three times a month or so..

Yep..,imac is only connected to electrical outlet on the wall..

Down payment amount cannot be higher/lower than the preset value Error

Hello. Can anyone help me with this error. When creating a down payment request from a sales order with a billing plan, I get the message 'Down payment amount cannot be higher/lower than the preset value' and the document isn't released to accounting. When creating the sales order, I included a condition type that I created. The billing plan then calculates the down payment request value with the total sum i.e net value plus condition value. Upon creating the down payment request in VF01, I get this message. I did a test and noticed that, if the condition is not included in the sales order, the down payment request is created without errors. How do I correct this? Thanks for you anticipated response.

Hi
As you are getting error, 'Down payment amount cannot be higher/lower than the preset value' ,please check the total value of the document.So in the sales document ,billing plan check what is the invoice value for the first billing date , also check what is the sales order value.Secondly what is the condition type that has been created and for what purpose it is being used.
Regards
Srinath

K8D Master-F High/Low beep tones

Hello,
Running the system even on bare minimum (PSU, memory and CPUs only) the board will not post and will only return a constant high then low tone beep code. Information from AMIBIOS suggests faulty CPUs, but this is doubtful that both CPUs would be damaged (I've tried one at a time, and in different sockets), as their serial numbers are quite a distance apart.
Anything else I can try? or do I have a dead board?
Thanks in advance,
LJP

Quote
Originally posted by Wonkanoby
it would help if you listed full hardware specs
and psu details
the 4 pin 12v feed is connected?
the ram is registered ddr ?
Full specs:
MSI K8D Master-F motherboard
2x Opteron 240 CPUs
4xGiel 512mb Dual channel ddr 3200 ram (even with all removed it gives the high low beep tones)
This board uses a SSI compliant PSU, its 24 pin main power, 8 pin additional power. 550W supply thats in it.
*Mass of edits*
Couldn't tell you if its registered DDR, ram isnt the problem though, it would give a ram error beep code running with no ram onboard, yet it still has the high/low beeptones.

How come some apps won't play sound on a USB device but only on the internal speaker while others can?

How come some apps won't play sound on a USB device but only on the internal speaker while others can? Mac OS 10.8.5

You can simply set your system preferences
Sound preference
output - to whatever your USB device/audio interface is
Your question seems a bit vague to me though. So can you actually inform us of what it is you are trying to do and give us examples with named kit.

High pitch ringing sound when i plug my headphones in.

Hi
I am currently using a Macbook Pro 15" retina display
There has been no problems previously. Out of no where, today my headphones has this high pitched ringing sound whenever i plug it in.
The audio is fine when I do not use any headphones. but when i plug them in, there is a ringing sound. This is happens as well when i plug in other headphones I have.
I have tried going to Sound under System Preferences and adjusting the stuff there but nothing seems to work.
This ringing sound makes listening to anything unbearable.
Please help

There is a micro switch inside the socket to switch between the optical output (digtal), headphones and internal speakers. It sometimes gets stuck.
Push the headphone plug into the socket numereous times and see if it frees the switch. Please do not push other foreigh objects into the socket as you may break the switch and/or the electrical contacts.

High Pitched Microphone sound

My laptop - ASUS K501L - produces a high pitched whistling sound, as well as other background static noises, when I use Skype. However, the problem is not present on other platforms, such as Google Hangouts and Line. I have tried manually adjusting the mic volume, but this does not fix the issue, and moreover it does not seem to change the volume of sound the receiving party hears. Plugging in earphones to eliminate audio feedback also does not work, but muting my mic stops the static the other end hears.
Thus, I have determined it is a problem with Skype, but I can't find any way to fix this. Help?
Thanks!

Hey, great suggestion Burn. It prompted me to look at iChat preferences, since that was the only application that I've had open which might engage the internal microphone.
Within iChat Preferences, I clicked on the 'Video' icon, and for the 'Microphone' setting I saw that 'None selected' (or something like that - that option has gone now?) was in place. So I changed the setting to Internal Microphone. The whistle or screech was still there. Then I changed the setting to 'Line In'. No more screech!!
A good result, but is this the way it's supposed to be? Does having the setting as 'Line In' mean that I have to plug headphones in whenever I want to use iChat for internet telephony? Unless I manually change to Internal Microphone, but then I suffer screeching again?
Cheers, Steven

Expressions and Defining High/Low Limits

I have an accuracy requirement to assign a 1.5% and a 1% High/Low from a previous test. The previous test is a Numeric Array where the first 12 values have to be assigned a 1.5% limit and the remaining 4 have a 1% limit.
Is there a way to do two while loops on the same step or do I have to break out each element in the array and define its own Parameter.
So basically I have something like this so far:
First test with post expression:
Parameters.Test = Step.NumericArray
Then I have an expression step with the loop options going 1-16 with this...
RunState.NextStep.Result.Measurement[ RunState.LoopIndex ].Limits.Low = (Parameters.Test[ RunState.LoopIndex ] * 0.985),
RunState.NextStep.Result.Measurement[ RunState.LoopIndex ].Limits.High = (Parameter.Test RunState.LoopIndex ] * 1.015)
But as you see that will add a 1.5% to all of them...Do I have to break out each element in the array individually?? Or is there a way to modify that expression to make the last 4 values of my array multiply by .99 and 1.01?
Thanks
Message Edited by Roons1159 on 02-20-2007 03:22 PM

I got it.. I didn't know I could define paramters for any given step in a sequence, only thought Step, previous step, and next step...

No sound when AT2020 USB mic is connected.

Followed set up instructions I can see logic pro x recognizes the mic but I get no sound. I will only get sound from my USB keyboard when the USB mic is disconnected.

Did you select the USB audio in the audio menu ? Have you created an audio track on the arrage page and selected the proper input source (AT2020 USB) and lastly did you record enable the audio track or the (I) at the bottom of the channel strip to audition the incoming audio signal?

How to display and print CCR showing not only results, high, low or normal, but also normal ranges of tests.

How do I display and print CCR showing not only my actual results, high, low or normal results, but also normal ranges of each test? I can do this individually but not for the composite CCR.
Thanks.

Hi,
I'm not exactly clear on what you are doing. I can tell you that the ranges and flags for high, low, and normal come from the lab results provider in the lab results they sent you, not from HealthVault. If you go back to the original document that came from
the laboratory, you should be able to open it as a document and print it.
I hope this helps. If not, please respond with more details, or if you'd prefer a private conversation, please contact HealthVault customer support by opening a support ticket with them.
Thanks,
Kathy

Strange high low frequencyy sound in solaris 11 usb live

Similar Messages

Maybe you are looking for