Streaming from Denon receiver to Airport Express Base Station?

Hello,
i know it's possible to strem music, video, etc. from your apple device to a Denon receiver with airplay, but is it also possible, to stream sound from the Denon receiver to an Airport Express Base Station? I'm about to purchase such a Denon receiver and 2 Airport Express Base Station. To the Airport Express Base Station's i want to connect speakers, the Denon receiver will be connected to the TV and Bluray. So i was wondering, if i could stream the sound from the TV / Bluray, via the Denon receiver to the Airport Express Base Stations. Or is the airplay function of the Denon a one-way road?
Thanks for feedback!
Jay

Jayelkay wrote:
is the airplay function of the Denon a one-way road?
yes.

Similar Messages

I want to re-use my old airport express base station but airport utility doesn't recognise it anymore (it dates from 2005) i would like to use it to connect to my speakers only

I have an old airport express base station from 2005
I would like to have a network on it so i can put it upstairs in a room and connect my speakers to it so i can send my music (from itunes) over the airport to my speakers.
I reset it and now i want to configure but the Airport utility doesn't recognise it anymore.
Can i update the firmware? has it become useless because too old or what can i do?
I work on macbook pro with macOSX 10.9.4
Can someone give me some tips please
thanks
J

Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

I have two airport express base stations that I want to configure on two separate sets of speakers in two separate rooms. How do I do this? Airport Utility only seems to scan one express at a time.

I am currently running a PowerPC G5 imac and have a wired broadband modem via ethernet with airport wireless network turned on, on the G5. I have the computer in the bedroom and have an airport express wired into a mixer that connects to my stereo. I have recently bought another airport express base station to connect to a pair of active monitors in the kitchen. When I try to scan these on Airport Utility version 5.42 I am only managing to scan one base unit at a time. I have plugged them in separately and reset them, they both have firmware updates, however the utility will only read one at once. I have read that you can link base stations to the same WDS. I would like to know how to go about doing this if it will only scan one airport express at a time. I have looked it up on the net and not found anything that is a simple fix. Can anyone help? In Apple Support it says that multiple Base Stations can be used. I would like to get both Apple Airport Express units to be able play airtunes separately or at the same time depending where I am in my flat. I do not need different music in each room. I would like to stream music from the computer to multiple rooms in the flat without having to continually unplug and configure the Base Stations. Has anyone come across such a challenge? Any help would be welcome.

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

Can you add new AirPort Express Base Station Simultaneous dual-band 802.11n with a 1st Gen time capsule network

Hi
Has anyone tried using the AirPort Express Base Station with a first generation Time Capsule and used it to extend their network, while still being able to use the Simultaneous dual-band 802.11n on their network?
Thanks in advance

The first generation Time Capsule was not a simultaneous dual band device.
If you add the "new" AirPort Express to the network and configure it to "Extend a wireless network", it will extend the one single band signal that it is receiving from the Time Capsule.
In other words, the AirPort Express will not extend simultaneous dual bands in this type of setup...since it can only "extend" what it receives. You would need a simultaneous dual band Time Capsule if you want that type of functionality.

I have got a Airport Extreme Basestation and an 3 x Airport Express Base station.

Hi
I have a netgear modem. Would like help with how to create one network with strong wireless signal all around the house and the gym outside. I basically know how I will setup the Airport Extreme and One Express ( for streaming music from Itunes ). How to use the other two Expresses to extend the wireless side of the network to have a strong signal all around the residental area.
Please help

Not knowing your exact building floorplan, I would start with the following basic setup of your AirPorts:
Connect the 802.11n AirPort Extreme Base Station (AEBSn) to the Netgear router by Ethernet.
Reconfigure the AEBSn as a bridge.
Configure the AEBSn for the option "Allow this network to be extended" enabled.
Configure each of the 802.11n AirPort Express Base Stations (AXn) with the option "Wireless Mode = Extend a wireless network" enabled.
Both AXns will be connected back to the AEBSn by wireless.

Getting the Most Out of My Airport Express Base Station, Part# MB321LLA

I'm assigned in northern Europe and have recently ordered an Airport Express Base Station through the APO (US Military Postal Service). It hasn't arrived yet and I decided to read up on it's positives and negatives. I currently have an Apple iMac 27" and a HP PC on my wireless network at home. I recently purchased an iPad2 and enjoy using it over my wireless network while sitting in the living room in the evenings. Unfortunately, the wireless signal alternates between 1 and 2 bars (sometimes even 0 bars) causing considerable delay in downloading and surfing the web on my new iPad2. I recently purchased a new LED Samsung "Smart System" HD TV and plan on setting it up in the living room this next weekend (replacing a very old TV). Part of my plan was to order (which I have along with the Airport Express) Apple TV and hook it up to the new HD TV at the same time. I was concerned about the wireless signal strength, due to the non-Apple wireless router being on the far end of my home, so I ordered the Airport Express hoping it would do the job of boosting the range and also helping increase the wireless signal strength for both my Apple TV (which is still on order) and my newly purchased iPad2.
The question is this: What is the best way for me to set up the Airport Express to optimize the wireless network (and my investment). As previously mentioned, the primary non-Apple wireless router is at least 50 ft away and is on the far end of the house (going through several thick walls in the process) from my living room area where the new HD TV is to be installed. Is it best to just add the Airport Express to the existing router via an Ethernet connection and emulate the existing wireless network, or is it best to actually set it up in the living room at the other end of the house?
I wish I had read the comments in this forum prior to having ordered this new Airport Express device.
Thanks...
Cheyenne22

What is the best way for me to set up the Airport Express to optimize the wireless network (and my investment).
The "best" way to connect network devices is always using a wired Ethernet connection if possible. Bandwidth is much higher, and you don't have to worry about wireless interference from other electronic sources in the area or obstructions in the signal path that reduce the signal strength quickly.
The AirPort Express can "extend" or "repeat" a wireless signal (using a wireless connection only) from another AirPort router, such as an AirPort Extreme, Time Capsule, or another AirPort Express. But, unfortunately it will not perform this service with devices from other manufacturers.
So, you will have to go the Ethernet connection option for your network.
If you configure the AirPort Express to "create a wireless network" using the exact same wireless network name, same type of security setting, and same password as your main router, it will provide more wireless coverage in the area where it is located.
The AirPort Express will need to be in "bridge mode" to do this. AirPort Utility, the application used to set up the AirPort Express will walk you through the installation and select the bridge mode option for you.
You can use the USB port on the AirPort Express to connect a compatible printer. If you want to stream AirTunes to the Express, you will be able to do that as well.

Problems setting up AirPort Express Base Station

I'm a real newbie at this, so pardon the ignorance in advance haha.
I just bought a new Airport Express base station. I wanted to be able to stream my music via iTunes to my living room. I'm just having problems getting the aiport utility to recognize the base station. I have the base station plugged in and everything. Right now it is flashing the amber light.
This is my set-up. I have a Netgear WGR614 54MBPS wireless G router connected to my broadband modem. From the router I have it connected to my desktop thats running windows xp pro. The network is up and running just fine. I can connect via any laptop or other device with wifi. Now, how do I get my wireless router to pick up the base station? Do I have to wrong idea here or something? haha. thanks in advance!

In the Airport Utility for your Airport Express, you should set the Airport Express in "client" mode. You might have to connect your Airport Express directly to your router with ethernet cable, while doing this. If you are using encryption, make sure that you enter the encryption number onto the express that your router/access point is using. Again, if you plug the Express directly into the router, you should be able to modify the settings quite easily. Once you unplug the express, it will blink orange for awhile (maybe a minute), so wait a bit.
Good luck.

Anybody use an Apple AirPort Express Base Station (windows)

http://store.apple.com/uk/product/MB...mco=MTIxODk3Mw
Im thinking about getting one of these and just wanting people opinions on it working with windows.
Just im a little confused, can i use it as a wireless router insted of my net gear, or will i still have to use my net gear router. My internet comes from the telephone wire if that helps?
Many thanks James

Hello jshrubb. Welcome to the Apple Discussions!
Since you didn't include the model of your Netgear router, it will be a little hard to determine if the AirPort Express Base Station (AX) could replace all of its functions.
So, here's what the AirPort Express is, and is not to help you decide:
o The AX is an Internet wireless router.
o The AX does not have a built-in modem: DSL, ADSL, Satellite or cable ... so one of these will still be required.
o The AX does not have a built-in Ethernet switch. It does have an Ethernet port, but that ports primary function is to be connected to the modem. However, it could be used to connect a wired client, but only if the AX is reconfigured as either a remote or relay base station in a Wireless Distribution System (WDS). The bottom-line here is that if you need to support wired clients, the AX would not be the appropriate choice for your network.
o The AX does support iTunes audio streaming so that when connected to either a pair of powered speakers or an audio system, you can stream iTunes to speakers wirelessly.

Can't read airport express base station configuration wirelessly

The setup:
2TB time capsule that takes the ethernet feed from the cable modem for internet access.
Airport express 802.11g plugged into speakers for Airtunes. No ethernet connection, just a wireless network.
The problem:
I can only read the airport express base station configuration when the mac is plugged into the time capsule by ethernet cable. This does not happen with the other mac I have on the network. It can connect to both the time capsule and the airport express without any problems. So unless I'm plugged in, iTunes and airtunes doesn't connect to the base station, and neither can Airfoil 3.5 or Airport Utility. Airport Utility does see the airport express. It just doesn't read the configuration wirelessly.
I think this had something to do with elgato eyetv not liking airfoil, but I can't say for sure.
Any thoughts?

When I switch it on all three lights flash, but then after a while the middle one stays on and nothing happens.
You posted in the AirPort Express area, but it sounds like you have an AirPort Extreme Base Station (AEBS)--correct?
If so, let's start by performing a complete power recycling of your network components to make sure that the BT Voyager router "recognizes" the AEBS.
Modem/Router Power Recycling - Quick
- Power-off the BT Voyager modem, AEBS, & computer(s); Wait at least 5 minutes.
- Power-on the BT Voyager modem; Wait at least 5 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
- Power-off the BT Voyager modem, AEBS, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the BT Voyager modem; Wait at least 30 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)

Airport Utility can no longer see my Airport Express Base Station.

Hi all the problem I have is as follows;
I've set up my Airport Express Base Station some time ago to print wirelessly from my HP Photosmart C4280 and it was working fine.
However recently when I've gone to print a document, even though the printer is working fine and the Airport Express Base Station is showing a green light nothing happens. I've gone into the Airport Utility and its say's it can't see the Airport Express Base Station (even though it still has a green light showing). If I unplug the Airport Express and plug it in again, the Airport Utility can suddenly see it again.
I've successfully gone through the reset process but after a few minutes the Airport Utility can no longer see the Airport Express Base Station which means I can't print a document wirelessly. I've repeated the reset process several times with the same outcome.
Everything was working fine up until recently, has the Airport Express Base Station developed a fault? or is there something I'm not doing.
Any advice would be greatly appreciated.

If you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices'

After downloading firmware for airport utility, airport express base station no longer registers with airport utility on my Mac. Now the base station is blinking amber with no info of what is causing all this to happen. Any suggestions?

After downloading firmware for airport utility last night, airport express base station was deleted from airport utility and only Time Capsule remains. When I plug in the base station, an amber light blinks without being able to verify the cause. Any suggestions to remedy this problem?

There are only a couple of things you can do to resuscitate a nonresponsive Express:
"Hard reset":
Press and hold the reset button with a pen or pencil until you see the status light (LED) start to flash amber rapidly, which should occur after about five seconds.
If that does not work,
"Factory defaults reset":
Unplug the Express from power.
Press and hold the reset button with a pen or pencil, then plug the Express back in while continuing to hold the button until you see the light (LED) flash rapidly. This should happen after a few seconds.
Release the button.
In either case you will have to reconfigure the Express as a new device. A moment or two after it has been reset, the LED should be blinking slowly. It must then appear in your Wi-Fi menu like this:
Earlier versions of OS X will report it as "Apple Network nnnnnn".
In either case, select it, and then launch AirPort Utility.
If it does no appear in your Wi-Fi menu after it has been reset using one of the two techniques above, it is defective. Other than attempting another reset, there is nothing you can do.

Airport Express Base Station and HP Laserjet 1020 printer connected

Dear all,
I have a Laptop (PC) Sony Vaio PCG-Z1XSP and an Airport Express Base Station which work perfectly together (internet access and I-tunes). I recently bought a printer HP Laserjet 1020 and connected it to the Airport Express USB soket. I managed to make it work and print a couple of times, but as soon as I turn off the printer or the computer or Airport Express, the next time I want to print, it doesn't work anymore.
The Airport Admin Utility recognises the printer (I can see it listed). I have updated the Airport Express software to the Firmware version 6.3 as well as downloaded the latest driver available on HP's website for my printer. I've also substituted the USB cable. Can anybody help me here? Thank you very much and best regards.

Hallo everybody,
Thanks for all the answers. I have contacted HP's chat online and gone through the problem with 3 different technicians. I've tried a lot myself too. The issue was partially solved by restarting the printer spooler, i.e. stop, then start and then restart it.
However after I was so happy that the printer worked, I turn off everything. When I turn on again, it was not working anymore. Then I tried to see by exclusion what the problem is, I had to restart the Hardwar I don't know how many times.
Conclusion:
1. The USB cable must be plugged into the airport express before turning on anything.
2. Turn on the printer first.
3. Turn on the airport express and the computer.
4. If you try to print it doesn't work, even if you reset the airport express through the airport express utility software. The printer is recognized and appears in it though.
5. Disconnect the USB cable from the airport express and connect it to the PC directly.
6. Print a document.
7. Disconnect the cable and reconnect it to the airport express.
8. Now you should be able to print wireless. You may need to reset the airport expresst with the utility softwar, but I managed to print without having to do it.
9. The pörinter works even if you turn off and on again the computer, or you suspend the windows session and restart it, or if you put it in standby and restart it.
10. The printer works even if you turn off the airport express and the computer, or the airport express alone and restart them/it.
11. The printer doens't work anymore if you turn it off and onn again. In such a case you have to plug in/out as discribeb above.
Solution: Leave the printer always on, or make the plug in/out every morning when you start the computer and print one page direclty before being able to print wireless.
Does anybody have a solution to this problem? I mean it prints, but it is annoying to plug in/out every day, no?
HP's technician says that it is not a recommanded solution the HP Laserjet 1020 with the airport express, since the printer works on a host based server basis... I mean it is easy to say that, but one expects to buy a printer that works always and not to have to plug in/out everyday, restart spooler and so on.
Can anybody comment or suggest anything I can do to avoid this? Thank you and I hope this helps others too.

I want to set up my Airport Express Base Station again but do not remember how. Please walk me thru it.

I am trying to hook my Airport Express Base Station up to be a router again and have forgotten how to do this. Before I had it hooked through the modeum and would like to have it that way again but for some reason the process has completely left my memory. I know it has something to do with the little icon on the top of the computer but not what it has to do with it. Because it is not hooked up I am unable to get my printer to work unless I connect to another wireless that I have but do not want to use all of the time since I have to pay for it and do not have many GB. I am also paying for another that I want to use all of the time (unless necessary to use the other) so It only cost me when I am away from home. Please walk me through the process of hooking the Apple router back up.

All apple routers are setup via Airport Utility.. there is no icon for it in the top menu area.. I think you are confusing the airport network setup (ie the internal wireless card in the Mac) with the airport express setup.. Apple insist on calling everything the same name which makes it more confusing.
Open the airport utility which you find under applications/utilties.
Router setting will depend on what version of the utility you are using.
In version 5 it is under Internet tab and in v6 utility under network. You need to set it to DHCP + NAT.
Download and read the manual for setting up the express if you have forgotten the details.. manuals are always good.. all the manuals are listed at the head of the section. But you are in Time Capsule instead of extreme/express specific area.
https://discussions.apple.com/community/wireless/airport
Manuals link http://support.apple.com/manuals/%23airport
If you want the express as router the modem should be bridged or it should be a pure modem for it to work without Double NAT issues. There is nothing wrong with bridging the Express.. that is not the same as using it in wireless bridge modes.. that is router bridge.
What modem do you have?
I am at a loss to understand the rest.. why the printer is not part of your own network.. and how setting up the airport this way is important. You need to give us specific details if you need more help.
How exactly is the airport setup now?
How do you connect to the modem?
How is the printer connected? What kind of printer?

1st generation airport express base station not showing up in network utilities

when i plug it in the amber light appears and sometimes blinks and/or sometimes steady. needless to say my desktop imac is not picking up its signal. what do i need to do to make it work or is it just not compatible with my new mac?

Your new iMac should not have any issues connecting to the 1st generation AirPort Express Base Station (AX).
When having difficulties accessing the AirPort thru the AirPort Utility, try the following, in order checking accessibility with the utility after each step:
Check the local connection. If you are trying to access the AirPort wirelessly, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the base station's LAN ports.
Power cycle the base station. Remove the power adapter's plug from the power outlet, and then, wait 15 seconds before plugging it back in.
Perform a "factory default" reset on the base station.

Connecting to multiple Airport Express base stations at the same time?

I want to be able to use wireless internet and stream music to my stereo at the same time, but I only have a single internet connection behind my stereo and it's connected to the Pay TV. My options seem to be getting a new line installed behind the stereo so I can insert this into the same Airport Express base station I use for my music, or buying a second Airport Express base station and connecting it to one of the other internet connections in the room, then connecting to both Airport Express base stations at the same time.
Is this possible? Are there other alternatives?
Many thanks

Nate, Welcome to the discussion area!
Once you have a network, you can connect multiple AirPort Express (AX) to that network (wirelessly or via Ethernet). When your computer joins that network it can access all the AX.
You could take your current internet connection and run it into an inexpensive router with multiple Ethernet ports (not the AX). If this is a wireless router then your AXs could be located elsewhere and connect as wireless clients to that network. Once you computer joined that network it could stream music to the AXs.

Streaming from Denon receiver to Airport Express Base Station?

Similar Messages

Maybe you are looking for