Stub Multicast Router on ASA

Hi,
I'm swapping out a PIX, IOS 6.3 with an ASA 5520 v8. The PIX has the following 2 commands in it's config:
multicast interface outside
multicast interface inside
These commands do not exist on the ASA. I do not wish to enable multicast routing. What commands on the ASA are equivalent to the multicast commands on the PIX?
Thanks
Yolande

hostname(config-if)#igmp
hostname(config-if)#igmp forward interface outside
This will enable the inside interface for IGMP forwarding and configure
all multicast requests coming from the inside interface and forward them
to the outside.
This should be it, remember to remove all your PIM configurations as PIM
and IGMP Stub Multicast Routing are not simultaneously supported.

Similar Messages

  • Help required in configuring multicast routing

    Hi,
    We have two 2 servers and 200 clients.
    2 servers are in one vlan, 200 clients are in another vlan.
    first server will send data to second server with multicast address 234.5.6.7
    second server will send data to 200 clients with multicast address 234.5.6.8
    first server is able to send data to second server.
    but second server is not able to send data to clients.
    If we put clients in same vlan, second server is able to send data to clients.
    So we understood that multicast routing needs to be enabled in L3 switch.
    Switch Model: 3550
    IOS version: 12.1(19)EA1a
    Any help in configuration required for this.........
    Regards
    SKRAO

    Hi Skrao,
    Does your client vlan and server vlan exist on same layer 3 switch if yes then perform this config and it should work..
    On global config mode
    ip multicast-routing distributed
    On interface vlan config (for both client vlan and server vlan)
    ip pim sparse-dense-mode
    You can very well fine tune later.Try this and update if it worked.
    HTH
    Ankur

  • Multicast routing daemons under Solaris 10 ?

    hi all
    i'm actually looking for a multicast routing daemon, for solaris 10 x86.
    any hint ?
    i tried to search for "mrouted", but it seems there's no recent version (last one seems to be for solaris 2.5, and sparc naturlly)
    help !
    thanks :)
    Edited by: Olivier_G on Apr 8, 2009 9:42 AM

    nm, i found. my collegs gave me the trick.
    quagga + zebra can do it.
    i just configured zebra (via quagga), it's like an IOS/Cisco router, and you can setup your comp as a router, and setup static routes, multicast and all.
    topic closed :) thanks.

  • Distributed multicast routing command not working on Catalyst 3850 switch

    Hi Cisco community,
    I was wondering if there is a known problem as to why the ip multicast-routing [distributed] option is not available on the Cat 3850 platforms
    global command " ip multicast-routing " is accepted 
    the configuration guide named:
    IP Multicast Routing Configuration Guide, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)
    First Published: January 29, 2013
    Last Modified: October 22, 2013
    explains that this option "key word" [distributed]  should be available>
    Enables IP multicast routing.
    ip multicast-routing [distributed] 
    Device(config)# ip multicast-routing distributed
    =============== Here is what i have and see =========
    Config attempt
    ============
    CAT-3850-1(config)#ip multicast-routing distributed
                                                ^
    Show command:
    ========
    CAT-3850-1#show ip multicast 
      Multicast Routing: enabled
      Multicast Multipath: disabled
      Multicast Route limit: No limit
      Multicast Fallback group mode: Sparse
      Number of multicast boundaries configured with filter-autorp option: 0
    Software:
    ========
    Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), 
    Version 03.03.03SE RELEASE SOFTWARE (fc2)
    License rights:
    ============
    CAT-3850-1#sh license right-to-use 
     Slot#  License name   Type     Count   Period left 
     1      ipservices   permanent     N/A   Lifetime
     1      apcount      adder         10     Lifetime
    License Level on Reboot: ipservices
     Slot#  License name   Type     Count   Period left 
     2      ipservices   permanent     N/A   Lifetime
     2      apcount      adder         10     Lifetime
    License Level on Reboot: ipservices
    Any hints and help would be greately appreciated.
    Many thanks in advance
    Markus 

    Hi Reza,
    Thank you for your quick reply, and for putting the record staright. As such, a helpful rating was provided
    PS: Feel free to help me one more time if you happend to know folllow on this query :)>
    I guess that the disributed function has been included in the standard mulitcast routing command because the key word is no longer needed. Or perhaps this platform does not support this at all.#
    Once again , thank you for your help above.
    Best regards

  • Setting up Multicast Routing for Imaging on HP Switches

    I've just spent a bit of time getting multicast imaging to work on our
    HP ProCurve switched network so I thought I'd post what was necessary
    so if anyone else had to look for it then they'd have some help.
    You'll need a switch capable of routing such as a 5300 series that is
    already routing regualr IP traffic. By default IGMP routing is disabled
    so that multicast traffic will not cross VLANs. Here's how to change
    that:
    Log into the 5300 in Manager mode (aka Admin)
    type "config" /goes into config mode
    type "ip multicast routing" /sets up IGMP routing
    type "router pim" /sets up Protocol Independant Multicast routing
    type "vlan *" /where * is a VLAN numeric ID
    type "ip igmp" /sets up IGMP routing on that VLAN
    type "ip pim" /sets up PIM routing on that VLAN
    Repeat those last three steps for all necessary VLANs
    type "exit" /to get back out of config mode - you may have to do
    that more than once
    type "wri mem" to save the config changes
    Then go out to any other switches in the network path for multicasts
    and login in Manager mode
    type "config"
    type "vlan *" /where * is VLAN numeric ID
    type "ip igmp" /turns on IGMP routing
    Repeat those last two steps for all VLANs that need it
    type "exit" /to get back out of config mode - you may have to do
    that more than once
    type "wri mem" to save the config changes
    That's it and it meant I went from "Session Master not found" to "New
    Image successful". I hope it helps somebody.
    Andrew

    On Fri, 22 Sep 2006 18:47:21 GMT, Andrew Ferris wrote:
    > I've just spent a bit of time getting multicast imaging to work on our
    > HP ProCurve switched network so I thought I'd post what was necessary
    > so if anyone else had to look for it then they'd have some help.
    Did somebody say coolsolutions?
    http://www.novell.com/coolsolutions/...mit_a_tip.html
    If you have already compiled drivers or have linux.2 please put them on
    http://forge.novell.com/modules/xfmo...ect/?zfdimgdrv
    Live BootCd and USB Disk from Mike Charles
    http://forge.novell.com/modules/xfmod/project/?imagingx
    eZie http://forge.novell.com/modules/xfmod/project/?ezie
    Marcus Breiden
    If you are asked to email me information please change -- to - in my e-mail
    address.
    The content of this mail is my private and personal opinion.
    http://www.edu-magic.net

  • Multicast route enabling

    I am doing video conference coding using jmf in internet.Instead of doing peer to peer,is it possible to do it in multicast?if yes,what about multicast route enabling?is thier any charge for enabling?Any software for enabling is available or we have to ask isp providers?please help.....

    is it possible or not...pLease help

  • Multicast routing issues when a subinterface is configured

    Strange issue here. Cisco and the vendor are unable to help so far...
    Most of our layer 3 lives on core switches. However, we have  a couple sites off our WAN connected via  Cisco routers. In these offices, we can not get paging to work.
    I  setup a lab and have finally determined what is at least causing the  issue. My lab "branch" has  the same problems, but I can resolve the  problem by removing the sub-interface off the router.
    On my LAN side  of the router, with this  config, everything works fine.
    #--- THIS WORKS ---#
    R1#
    ip pim rp-address 192.168.251.254
    gig 0/0 (connects to SW1 g0/1)
     ip address 10.254.253.254 255.255.255.0
     ip pim sparse-dense mode
    SW1#
     gig 0/1 (connects to R1 g0/0)
     !no config - default VLAN1
    When I apply this config...everything breaks. The phone goes off
    #--- THIS DOES NOT WORK ---#
    R1#
    ip pim rp-address 192.168.251.254
    gig 0/0 (connects to SW1 g0/1)
     no ip
    gig 0/0.777 (connects to SW1 g0/1)
     ip address 10.254.253.254 255.255.255.0
     ip pim sparse-dense mode
    SW1#
     gig 0/1 (connects to R1 g0/0)
     sw mode trunk
     sw trunk  encap dot1q
    int vlan 777
     ip address 10.254.253.1 255.255.255.0
     ip pim sparse-dense mode
    int vlan 778
     ip address 10.254.251.1 255.255.255.0
     ip pim sparse-dense mode
     gig 0/17 (phone port)
     switch access vlan 778 (keeping it simple for now)
    I have tried this on 2 different model routers, each with different IOS versions.  The same issues follow each router. What is it about the  sub interfaces?
    Any insight? Calling all multicast experts! Thanks!

    Hi,
    creating sub-interface should not create any difference here. Only difference i can see earlier switch was working in l2 mode now it is participating in multicast routing as SVI is configured and pim neighborship established. Have you configured RP address on SW1. Please share below outputs from both devices
    - running config
    - show ip mroute <group>
    - show ip pim rp address mapping
    Regards,
    Akash

  • Site to Site VPN Problems With 2801 Router and ASA 5505

    Hello,
    I am having some issue setting up a site to site ipsec VPN between a Cisco 2801 router and a Cisco ASA 5505. I was told there was a vpn previously setup with an old hosting provider, but those connections have been servered. Right now I am trying to get the sites to talk to the 2801. Here ere are my current configs, please let me know if you need anything else. Im stumped on this one. Thanks.
    IP scheme at SIte A:
    IP    172.19.3.x
    sub 255.255.255.128
    GW 172.19.3.129
    Site A Ciscso 2801 Router
    Current configuration : 11858 bytes
    version 12.4
    service timestamps debug datetime localtime
    service timestamps log datetime localtime show-timezone
    service password-encryption
    hostname router-2801
    boot-start-marker
    boot-end-marker
    logging message-counter syslog
    logging buffered 4096
    aaa new-model
    aaa authentication login userauthen group radius local
    aaa authorization network groupauthor local
    aaa session-id common
    clock timezone est -5
    clock summer-time zone recurring last Sun Mar 2:00 1 Sun Nov 2:00
    dot11 syslog
    ip source-route
    ip dhcp excluded-address 172.19.3.129 172.19.3.149
    ip dhcp excluded-address 172.19.10.1 172.19.10.253
    ip dhcp excluded-address 172.19.3.140
    ip dhcp ping timeout 900
    ip dhcp pool DHCP
       network 172.19.3.128 255.255.255.128
       default-router 172.19.3.129
       domain-name domain.local
       netbios-name-server 172.19.3.7
       option 66 ascii 172.19.3.225
       dns-server 172.19.3.140 208.67.220.220 208.67.222.222
    ip dhcp pool VoiceDHCP
       network 172.19.10.0 255.255.255.0
       default-router 172.19.10.1
       dns-server 208.67.220.220 8.8.8.8
       option 66 ascii 172.19.10.2
       lease 2
    ip cef
    ip inspect name SDM_LOW cuseeme
    ip inspect name SDM_LOW dns
    ip inspect name SDM_LOW ftp
    ip inspect name SDM_LOW h323
    ip inspect name SDM_LOW https
    ip inspect name SDM_LOW icmp
    ip inspect name SDM_LOW imap
    ip inspect name SDM_LOW pop3
    ip inspect name SDM_LOW netshow
    ip inspect name SDM_LOW rcmd
    ip inspect name SDM_LOW realaudio
    ip inspect name SDM_LOW rtsp
    ip inspect name SDM_LOW esmtp
    ip inspect name SDM_LOW sqlnet
    ip inspect name SDM_LOW streamworks
    ip inspect name SDM_LOW tftp
    ip inspect name SDM_LOW tcp
    ip inspect name SDM_LOW udp
    ip inspect name SDM_LOW vdolive
    no ip domain lookup
    ip domain name domain.local
    multilink bundle-name authenticated
    key chain key1
    key 1
       key-string 7 06040033484B1B484557
    crypto pki trustpoint TP-self-signed-3448656681
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-3448bb6681
    revocation-check none
    rsakeypair TP-self-signed-344bbb56681
    crypto pki certificate chain TP-self-signed-3448656681
    certificate self-signed 01
      3082024F
                quit
    username admin privilege 15 password 7 F55
    archive
    log config
      hidekeys
    crypto isakmp policy 10
    encr 3des
    hash md5
    authentication pre-share
    group 2
    crypto isakmp key XXXXX address 209.118.0.1
    crypto isakmp key xxxxx address SITE B Public IP
    crypto isakmp keepalive 40 5
    crypto isakmp nat keepalive 20
    crypto isakmp client configuration group IISVPN
    key 1nsur3m3
    dns 172.19.3.140
    wins 172.19.3.140
    domain domain.local
    pool VPN_Pool
    acl 198
    crypto isakmp profile IISVPNClient
       description VPN clients profile
       match identity group IISVPN
       client authentication list userauthen
       isakmp authorization list groupauthor
       client configuration address respond
    crypto ipsec transform-set myset esp-3des esp-md5-hmac
    crypto dynamic-map Dynamic 5
    set transform-set myset
    set isakmp-profile IISVPNClient
    qos pre-classify
    crypto map VPN 10 ipsec-isakmp
    set peer 209.118.0.1
    set peer SITE B Public IP
    set transform-set myset
    match address 101
    qos pre-classify
    crypto map VPN 65535 ipsec-isakmp dynamic Dynamic
    track 123 ip sla 1 reachability
    delay down 15 up 10
    class-map match-any VoiceTraffic
    match protocol rtp audio
    match protocol h323
    match protocol rtcp
    match access-group name VOIP
    match protocol sip
    class-map match-any RDP
    match access-group 199
    policy-map QOS
    class VoiceTraffic
        bandwidth 512
    class RDP
        bandwidth 768
    policy-map MainQOS
    class class-default
        shape average 1500000
      service-policy QOS
    interface FastEthernet0/0
    description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$$FW_INSIDE$
    ip address 172.19.3.129 255.255.255.128
    ip access-group 100 in
    ip inspect SDM_LOW in
    ip nat inside
    ip virtual-reassembly
    duplex auto
    speed auto
    interface FastEthernet0/0.10
    description $ETH-VoiceVLAN$$
    encapsulation dot1Q 10
    ip address 172.19.10.1 255.255.255.0
    ip inspect SDM_LOW in
    ip nat inside
    ip virtual-reassembly
    interface FastEthernet0/1
    description "Comcast"
    ip address PUB IP 255.255.255.248
    ip access-group 102 in
    ip inspect SDM_LOW out
    ip nat outside
    ip virtual-reassembly
    duplex auto
    speed auto
    crypto map VPN
    interface Serial0/1/0
    description "Verizon LEC Circuit ID: w0w13908 Site ID: U276420-1"
    bandwidth 1536
    no ip address
    encapsulation frame-relay IETF
    frame-relay lmi-type ansi
    interface Serial0/1/0.1 point-to-point
    bandwidth 1536
    ip address 152.000.000.18 255.255.255.252
    ip access-group 102 in
    ip verify unicast reverse-path
    ip inspect SDM_LOW out
    ip nat outside
    ip virtual-reassembly
    frame-relay interface-dlci 500 IETF 
    crypto map VPN
    service-policy output MainQOS
    interface Serial0/2/0
    description "PAETEC 46.HCGS.788446.CV (Verizon ID) / 46.HCGS.3 (PAETEC ID)"
    ip address 123.252.123.102 255.255.255.252
    ip access-group 102 in
    ip inspect SDM_LOW out
    ip nat outside
    ip virtual-reassembly
    encapsulation ppp
    crypto map VPN
    service-policy output MainQOS
    ip local pool VPN_Pool 172.20.3.130 172.20.3.254
    ip forward-protocol nd
    ip route 0.0.0.0 0.0.0.0 50.00.000.110 track 123
    ip route 0.0.0.0 0.0.0.0 111.252.237.000 254
    ip route 122.112.197.20 255.255.255.255 209.252.237.101
    ip route 208.67.220.220 255.255.255.255 50.78.233.110
    no ip http server
    no ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    ip flow-top-talkers
    top 20
    sort-by bytes
    ip nat inside source route-map COMCAST interface FastEthernet0/1 overload
    ip nat inside source route-map PAETEC interface Serial0/2/0 overload
    ip nat inside source route-map VERIZON interface Serial0/1/0.1 overload
    ip nat inside source static tcp 172.19.3.140 21 PUB IP 21 extendable
    ip access-list extended VOIP
    permit ip 172.20.3.0 0.0.0.127 host 172.19.3.190
    permit ip host 172.19.3.190 172.20.3.0 0.0.0.127
    ip radius source-interface FastEthernet0/0
    ip sla 1
    icmp-echo 000.67.220.220 source-interface FastEthernet0/1
    timeout 10000
    frequency 15
    ip sla schedule 1 life forever start-time now
    access-list 23 permit 172.19.3.0 0.0.0.127
    access-list 23 permit 172.19.3.128 0.0.0.127
    access-list 23 permit 173.189.251.192 0.0.0.63
    access-list 23 permit 107.0.197.0 0.0.0.63
    access-list 23 permit 173.163.157.32 0.0.0.15
    access-list 23 permit 72.55.33.0 0.0.0.255
    access-list 23 permit 172.19.5.0 0.0.0.63
    access-list 100 remark "Outgoing Traffic"
    access-list 100 deny   ip 67.128.87.156 0.0.0.3 any
    access-list 100 deny   ip host 255.255.255.255 any
    access-list 100 deny   ip 127.0.0.0 0.255.255.255 any
    access-list 100 permit tcp host 172.19.3.190 any eq smtp
    access-list 100 permit tcp host 172.19.3.137 any eq smtp
    access-list 100 permit tcp any host 66.251.35.131 eq smtp
    access-list 100 permit tcp any host 173.201.193.101 eq smtp
    access-list 100 permit ip any any
    access-list 100 permit tcp any any eq ftp
    access-list 101 remark "Interesting VPN Traffic"
    access-list 101 permit ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
    access-list 101 permit ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
    access-list 101 permit ip 172.19.3.128 0.0.0.127 host 172.19.250.10
    access-list 101 permit ip 172.19.3.128 0.0.0.127 host 172.19.250.11
    access-list 101 permit tcp any any eq ftp
    access-list 101 permit tcp any any eq ftp-data
    access-list 102 remark "Inbound Access"
    access-list 102 permit udp any host 152.179.53.18 eq non500-isakmp
    access-list 102 permit udp any host 152.179.53.18 eq isakmp
    access-list 102 permit esp any host 152.179.53.18
    access-list 102 permit ahp any host 152.179.53.18
    access-list 102 permit udp any host 209.000.000.102 eq non500-isakmp
    access-list 102 permit udp any host 209.000.000.102 eq isakmp
    access-list 102 permit esp any host 209.000.000.102
    access-list 102 permit ahp any host 209.000.000.102
    access-list 102 permit udp any host PUB IP eq non500-isakmp
    access-list 102 permit udp any host PUB IP eq isakmp
    access-list 102 permit esp any host PUB IP
    access-list 102 permit ahp any host PUB IP
    access-list 102 permit ip 72.55.33.0 0.0.0.255 any
    access-list 102 permit ip 107.0.197.0 0.0.0.63 any
    access-list 102 deny   ip 172.19.3.128 0.0.0.127 any
    access-list 102 permit icmp any any echo-reply
    access-list 102 permit icmp any any time-exceeded
    access-list 102 permit icmp any any unreachable
    access-list 102 permit icmp any any
    access-list 102 deny   ip any any log
    access-list 102 permit tcp any host 172.19.3.140 eq ftp
    access-list 102 permit tcp any host 172.19.3.140 eq ftp-data established
    access-list 102 permit udp any host SITE B Public IP  eq non500-isakmp
    access-list 102 permit udp any host SITE B Public IP  eq isakmp
    access-list 102 permit esp any host SITE B Public IP
    access-list 102 permit ahp any host SITE B Public IP
    access-list 110 remark "Outbound NAT Rule"
    access-list 110 remark "Deny VPN Traffic NAT"
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.10.0 0.0.0.255
    access-list 110 deny   ip 172.19.10.0 0.0.0.255 172.19.3.128 0.0.0.127
    access-list 110 deny   ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.11
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.10
    access-list 110 permit ip 172.19.3.128 0.0.0.127 any
    access-list 110 permit ip 172.19.10.0 0.0.0.255 any
    access-list 198 remark "Networks for IISVPN Client"
    access-list 198 permit ip 172.19.3.0 0.0.0.127 172.20.3.128 0.0.0.127
    access-list 198 permit ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
    access-list 199 permit tcp any any eq 3389
    route-map PAETEC permit 10
    match ip address 110
    match interface Serial0/2/0
    route-map COMCAST permit 10
    match ip address 110
    match interface FastEthernet0/1
    route-map VERIZON permit 10
    match ip address 110
    match interface Serial0/1/0.1
    snmp-server community 123 RO
    radius-server host 172.19.3.7 auth-port 1645 acct-port 1646 key 7 000000000000000
    control-plane
    line con 0
    line aux 0
    line vty 0 4
    access-class 23 in
    privilege level 15
    transport input telnet ssh
    line vty 5 15
    access-class 23 in
    privilege level 15
    transport input telnet ssh
    scheduler allocate 20000 1000
    ntp server 128.118.25.3
    ntp server 217.150.242.8
    end
    IP scheme at site B:
    ip     172.19.5.x
    sub  255.255.255.292
    gw   172.19.5.65
    Cisco ASA 5505 at Site B
    ASA Version 8.2(5)
    hostname ASA5505
    domain-name domain.com
    enable password b04DSH2HQqXwS8wi encrypted
    passwd b04DSH2HQqXwS8wi encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 172.19.5.65 255.255.255.192
    interface Vlan2
    nameif outside
    security-level 0
    ip address SITE B public IP 255.255.255.224
    boot system disk0:/asa825-k8.bin
    ftp mode passive
    clock timezone est -5
    clock summer-time zone recurring last Sun Mar 2:00 last Sun Oct 2:00
    dns server-group DefaultDNS
    domain-name iis-usa.com
    same-security-traffic permit intra-interface
    object-group network old hosting provider
    network-object 72.55.34.64 255.255.255.192
    network-object 72.55.33.0 255.255.255.0
    network-object 173.189.251.192 255.255.255.192
    network-object 173.163.157.32 255.255.255.240
    network-object 66.11.1.64 255.255.255.192
    network-object 107.0.197.0 255.255.255.192
    object-group network old hosting provider
    network-object host 172.19.250.10
    network-object host 172.19.250.11
    access-list 100 extended permit ip 172.19.5.64 255.255.255.192 object-group old hosting provider
    access-list 100 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.128 255.255.255.128
    access-list 10 extended deny ip 0.0.0.0 255.0.0.0 any
    access-list 10 extended deny ip 127.0.0.0 255.0.0.0 any
    access-list 10 extended deny ip 169.254.0.0 255.255.0.0 any
    access-list 10 extended deny ip 172.16.0.0 255.255.0.0 any
    access-list 10 extended deny ip 224.0.0.0 224.0.0.0 any
    access-list 10 extended permit icmp any any echo-reply
    access-list 10 extended permit icmp any any time-exceeded
    access-list 10 extended permit icmp any any unreachable
    access-list 10 extended permit icmp any any traceroute
    access-list 10 extended permit icmp any any source-quench
    access-list 10 extended permit icmp any any
    access-list 10 extended permit tcp object-group old hosting provider any eq 3389
    access-list 10 extended permit tcp any any eq https
    access-list 10 extended permit tcp any any eq www
    access-list 110 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.0 255.255.255.128
    access-list 110 extended permit ip 172.19.5.64 255.255.255.192 object-group old hosting provider
    pager lines 24
    logging enable
    logging timestamp
    logging console emergencies
    logging monitor emergencies
    logging buffered warnings
    logging trap debugging
    logging history debugging
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip verify reverse-path interface inside
    ip verify reverse-path interface outside
    ip audit name jab attack action alarm drop reset
    ip audit name probe info action alarm drop reset
    ip audit interface outside probe
    ip audit interface outside jab
    ip audit info action alarm drop reset
    ip audit attack action alarm drop reset
    ip audit signature 2000 disable
    ip audit signature 2001 disable
    ip audit signature 2004 disable
    ip audit signature 2005 disable
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit 75.150.169.48 255.255.255.240 outside
    icmp permit 72.44.134.16 255.255.255.240 outside
    icmp permit 72.55.33.0 255.255.255.0 outside
    icmp permit any outside
    icmp permit 173.163.157.32 255.255.255.240 outside
    icmp permit 107.0.197.0 255.255.255.192 outside
    icmp permit 66.11.1.64 255.255.255.192 outside
    icmp deny any outside
    asdm image disk0:/asdm-645.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list 100
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group 10 in interface outside
    route outside 0.0.0.0 0.0.0.0 174.78.151.225 1
    timeout xlate 3:00:00
    timeout conn 24:00:00 half-closed 0:10:00 udp 0:10:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 24:00:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    http 107.0.197.0 255.255.255.192 outside
    http 66.11.1.64 255.255.255.192 outside
    snmp-server host outside 107.0.197.29 community *****
    snmp-server host outside 107.0.197.30 community *****
    snmp-server host inside 172.19.250.10 community *****
    snmp-server host outside 172.19.250.10 community *****
    snmp-server host inside 172.19.250.11 community *****
    snmp-server host outside 172.19.250.11 community *****
    snmp-server host outside 68.82.122.239 community *****
    snmp-server host outside 72.55.33.37 community *****
    snmp-server host outside 72.55.33.38 community *****
    snmp-server host outside 75.150.169.50 community *****
    snmp-server host outside 75.150.169.51 community *****
    no snmp-server location
    no snmp-server contact
    snmp-server community *****
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto map VPNMAP 10 match address 110
    crypto map VPNMAP 10 set peer 72.00.00.7 old vpn public ip Site B Public IP
    crypto map VPNMAP 10 set transform-set ESP-3DES-MD5
    crypto map VPNMAP 10 set security-association lifetime seconds 86400
    crypto map VPNMAP 10 set security-association lifetime kilobytes 4608000
    crypto map VPNMAP interface outside
    crypto isakmp identity address
    crypto isakmp enable outside
    crypto isakmp policy 20
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet 172.19.5.64 255.255.255.192 inside
    telnet 172.19.3.0 255.255.255.128 outside
    telnet timeout 60
    ssh 0.0.0.0 0.0.0.0 inside
    ssh 0.0.0.0 0.0.0.0 outside
    ssh timeout 60
    console timeout 0
    management-access inside
    dhcpd dns 172.19.3.140
    dhcpd wins 172.19.3.140
    dhcpd ping_timeout 750
    dhcpd domain iis-usa.com
    dhcpd address 172.19.5.80-172.19.5.111 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection scanning-threat shun except object-group old hosting provider
    threat-detection statistics
    threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
    ntp server 128.118.25.3 source outside
    ntp server 217.150.242.8 source outside
    tunnel-group 72.00.00.7 type ipsec-l2l
    tunnel-group 72.00.00.7 ipsec-attributes
    pre-shared-key *****
    tunnel-group old vpn public ip type ipsec-l2l
    tunnel-group old vpn public ip ipsec-attributes
    pre-shared-key *****
    tunnel-group SITE A Public IP  type ipsec-l2l
    tunnel-group SITE A Public IP  ipsec-attributes
    pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect netbios
      inspect tftp
      inspect pptp
      inspect sip 
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:
    : end

    I have removed the old "set peer" and have added:
    IOS router:
    access-list 101 permit ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.65
    ASA fw:
    access-list 110 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.128 255.255.255.128
    on the router I have also added;
    access-list 110 deny  ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.63
    Here is my acl :
    access-list 110 remark "Outbound NAT Rule"
    access-list 110 remark "Deny VPN Traffic NAT"
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.10.0 0.0.0.255
    access-list 110 deny   ip 172.19.10.0 0.0.0.255 172.19.3.128 0.0.0.127
    access-list 110 deny   ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.11
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.10
    access-list 110 permit ip 172.19.3.128 0.0.0.127 any
    access-list 110 permit ip 172.19.10.0 0.0.0.255 any
    access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.63
    access-list 198 remark "Networks for IISVPN Client"
    access-list 198 permit ip 172.19.3.0 0.0.0.127 172.20.3.128 0.0.0.127
    access-list 198 permit ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
    Still no ping tothe other site.

  • One router on ASA 5505 Site to Site VPN can't ping other router

    I have two Cisco ASA routers and I have a site to site vpn set up between the two. The VPN link works but Site A can't ping anything on Site B. Site B can ping Site A. Site B can ping other pcs on it's own network. Site A has been in place for a while and has other site to site VPNs that work fine, so I think the problem is with Site B. Here is the config for Site B:
    Result of the command: "show running-config"
    : Saved
    ASA Version 8.4(4)1
    hostname SaskASA
    enable password POgOWyKyb0jgJ1Hm encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.16.1 255.255.254.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    ftp mode passive
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network NETWORK_OBJ_192.168.16.0_23
    subnet 192.168.16.0 255.255.254.0
    object network NETWORK_OBJ_192.168.2.0_23
    subnet 192.168.2.0 255.255.254.0
    access-list outside_cryptomap extended permit ip 192.168.16.0 255.255.254.0 192.168.2.0 255.255.254.0
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source static NETWORK_OBJ_192.168.16.0_23 NETWORK_OBJ_192.168.16.0_23 destination static NETWORK_OBJ_192.168.2.0_23 NETWORK_OBJ_192.168.2.0_23 no-proxy-arp route-lookup
    object network obj_any
    nat (inside,outside) dynamic interface
    nat (inside,outside) after-auto source dynamic any interface
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable 444
    http 192.168.16.0 255.255.254.0 inside
    http 0.0.0.0 0.0.0.0 inside
    http 0.0.0.0 0.0.0.0 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev2 ipsec-proposal DES
    protocol esp encryption des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
    protocol esp encryption 3des
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
    protocol esp encryption aes
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
    protocol esp encryption aes-192
    protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
    protocol esp encryption aes-256
    protocol esp integrity sha-1 md5
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs group1
    crypto map outside_map 1 set peer 207.228.xx.xx
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
    crypto map outside_map interface outside
    crypto ikev2 policy 1
    encryption aes-256
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 10
    encryption aes-192
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 20
    encryption aes
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 30
    encryption 3des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 policy 40
    encryption des
    integrity sha
    group 5 2
    prf sha
    lifetime seconds 86400
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication crack
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication rsa-sig
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 40
    authentication crack
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 50
    authentication rsa-sig
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 60
    authentication pre-share
    encryption aes-192
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 70
    authentication crack
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 80
    authentication rsa-sig
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 90
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication crack
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 110
    authentication rsa-sig
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 120
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 130
    authentication crack
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 140
    authentication rsa-sig
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 150
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    dhcp-client client-id interface outside
    dhcpd auto_config outside
    dhcpd address 192.168.16.100-192.168.16.200 inside
    dhcpd auto_config outside interface inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy GroupPolicy_207.228.xx.xxinternal
    group-policy GroupPolicy_207.228.xx.xx attributes
    vpn-tunnel-protocol ikev1 ikev2
    username User password shbn5zbLkuHP/mJX encrypted privilege 15
    tunnel-group 207.228.xx.xxtype ipsec-l2l
    tunnel-group 207.228.xx.xxgeneral-attributes
    default-group-policy GroupPolicy_207.228.xx.xx
    tunnel-group 207.228.xx.xxipsec-attributes
    ikev1 pre-shared-key *****
    ikev2 remote-authentication pre-shared-key *****
    ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    message-length maximum client auto
    message-length maximum 512
    policy-map global_policy
    class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    inspect ip-options
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:f06bd1d6d063318339d98417b171175e
    : end
    Any ideas? Thanks.

    I looked over the config for Site A, but couldn't find anything unusual. Perhaps I'm overlooking something. Here is the config for site A:
    Result of the command: "show running-config"
    : Saved
    ASA Version 8.2(1)
    hostname SiteA
    domain-name domain
    enable password POgOWyKyb0jgJ1Hm encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.2.1 255.255.254.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns domain-lookup inside
    dns server-group DefaultDNS
    name-server 192.168.2.6
    domain-name domain
    object-group network DM_INLINE_NETWORK_1
    network-object 192.168.14.0 255.255.254.0
    network-object 192.168.4.0 255.255.254.0
    network-object 192.168.6.0 255.255.254.0
    network-object 192.168.8.0 255.255.254.0
    object-group network DM_INLINE_NETWORK_2
    network-object 192.168.12.0 255.255.254.0
    network-object 192.168.14.0 255.255.254.0
    network-object 192.168.4.0 255.255.254.0
    network-object 192.168.6.0 255.255.254.0
    network-object 192.168.8.0 255.255.254.0
    access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.254.0 object-group DM_INLINE_NETWORK_1
    access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.254.0 object-group DM_INLINE_NETWORK_2
    access-list inside_nat0_outbound extended permit ip any 192.168.15.192 255.255.255.192
    access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.254.0 192.168.16.0 255.255.254.0
    access-list VPNGeo_splitTunnelAcl standard permit any
    access-list outside_2_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.6.0 255.255.254.0
    access-list outside_3_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.4.0 255.255.254.0
    access-list outside_4_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.8.0 255.255.254.0
    access-list outside_5_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.16.0 255.255.254.0
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool GeoVPNPool 192.168.15.200-192.168.15.254 mask 255.255.254.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable 444
    http 192.168.2.0 255.255.254.0 inside
    http 0.0.0.0 0.0.0.0 inside
    http 0.0.0.0 0.0.0.0 outside
    http authentication-certificate inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group1
    crypto map outside_map 1 set peer 207.228.xx.xx
    crypto map outside_map 1 set transform-set ESP-3DES-SHA
    crypto map outside_map 2 match address outside_2_cryptomap
    crypto map outside_map 2 set pfs
    crypto map outside_map 2 set peer 208.119.xx.xx
    crypto map outside_map 2 set transform-set ESP-3DES-SHA
    crypto map outside_map 3 match address outside_3_cryptomap
    crypto map outside_map 3 set pfs group1
    crypto map outside_map 3 set peer 208.119.xx.xx
    crypto map outside_map 3 set transform-set ESP-3DES-SHA
    crypto map outside_map 4 match address outside_4_cryptomap
    crypto map outside_map 4 set pfs
    crypto map outside_map 4 set peer 208.119.xx.xx
    crypto map outside_map 4 set transform-set ESP-3DES-SHA
    crypto map outside_map 5 match address outside_5_cryptomap
    crypto map outside_map 5 set pfs group1
    crypto map outside_map 5 set peer 70.64.xx.xx
    crypto map outside_map 5 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 0.0.0.0 0.0.0.0 inside
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcp-client client-id interface outside
    dhcpd auto_config outside
    dhcpd address 192.168.2.100-192.168.2.254 inside
    dhcpd auto_config outside interface inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy VPNGeo internal
    group-policy VPNGeo attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value VPNGeo_splitTunnelAcl
    username user password shbn5zbLkuHP/mJX encrypted privilege 15
    username namepassword vP98Lj8Vm5SLs9PW encrypted
    username nameattributes
    vpn-group-policy VPNGeo
    tunnel-group 207.228.xx.xxtype ipsec-l2l
    tunnel-group 207.228.xx.xxipsec-attributes
    pre-shared-key *
    tunnel-group VPNGeo type remote-access
    tunnel-group VPNGeo general-attributes
    address-pool GeoVPNPool
    default-group-policy VPNGeo
    tunnel-group VPNGeo ipsec-attributes
    pre-shared-key *
    tunnel-group 208.119.xx.xxtype ipsec-l2l
    tunnel-group 208.119.xx.xxipsec-attributes
    pre-shared-key *
    tunnel-group 208.119.xx.xx type ipsec-l2l
    tunnel-group 208.119.xx.xx ipsec-attributes
    pre-shared-key *
    tunnel-group 208.119.xx.xxtype ipsec-l2l
    tunnel-group 208.119.xx.xxipsec-attributes
    pre-shared-key *
    tunnel-group 70.64.xx.xxtype ipsec-l2l
    tunnel-group 70.64.xx.xxipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    message-length maximum 512
    policy-map global_policy
    class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:e3adf4e597198f58cd21e508aabdbab9
    : end

  • 1 router === 2 ASA (how to connect without switch)

    Internet ----  ASR ------ Switch ------- ASA 1 (active) 
                                           |              |
                                           |              |
                                           |---------- ASA 2 (standby)
    ASR supports BDI (Bridge Domain Interface), in that case, it seems like possible.

    Hi,
    I think you might be able to bridge the 2 interfaces (even if they are not switchports) and enable the use of ASA Failover behind the 2 interfaces. I have only operated one ASR1001 just lately. To my understanding every port it has is a normal router port.
    Have a look at this section of the configuration guide
    http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/bdi.html
    Also have a look at this thread on these forums which seems to handle the same situation as yours
    https://supportforums.cisco.com/thread/2169496
    Hope this helps
    Please remember to mark the question as answered if it was.
    - Jouni

  • Error when attempting to remove static route from ASA 5525x running version 9.0(4)

    Hello, 
    I am having difficulty in removing static routes from my ASA5525x, hoping someone here may be able to help.
    Example:
    ASA5525X/pri/act# sh route | in 192.168
    S    192.168.60.0 255.255.255.0 [1/0] via 64.57.xxx.xx, OUTSIDE
    ATLCOLO-ASA5525X/pri/act(config)# no route OUTSIDE 192.168.60.0 255.255.255.0 64.57.xxx.xx
    %No matching route to delete
    There are several which need to be removed, all 192.168.x.x/24, pointing to the Outside interface using the same address 64.57.xxx.xx

    Hi,
    I think i agree with Jon that this is probably due to RRI from the VPN configuration.
    Also , check this output:-
    show asp table routing and see if you see it in here as well.
    We also have some defects so please provide the relevant interface and routing configuration and also the ASA code version.
    Thanks and Regards,
    Vibhor Amrodia

  • Policy base routing in asa

    hi 
    i attach picture
    i want answer to any user from the same router
    example :
    request user1 from isp1 , i answer it from same isp1 router
    i think asa dose not support pbr ,, please help me with same senario .

    policy-based routing, similar to what an IOS router can do  based on incoming traffic and then overriding the routing table for the next hop, isn't a feature in the ASA.
    We can do policy based NAT, inspection and filtering, but not policy based routing.

  • Consumer Edge Router to ASA to Internal

    I have a difficult problem...Please forgive my ignorance.
    I have a consumer-grade router called a "Fritz!Box 7390" on the edge of our network (in Germany -- very capable, very popular little box).
    Following are the telephony characteristics:
    ISDN BRI is emulated but runs over IP (as far as I understand, Telekom is trying to move all their clients to this configuration, or at least some form of it)
    The device has two analog phone jacks and one ISDN -- we use all three: 1x for our regular telephone; 1x for our fax machine; 1x for a home office ISDN line
    Next are the "WAN" characteristics:
    The device connects to Deutsche Telekom over VDSL at 50Mbps down / 10Mbps up
    The Fritz!Box allows for opening TCP/UDP ports to just a single device/IP address, not to an entire network
    We currently have HTTP, HTTPS, SMTP, and Microsoft's RDP protocols opened to various servers running on Hyper-V virtual machines
    We use Dyn's DDNS to resolve our internal Microsoft domain and Exchange servers
    The device does allow for establishing a default route to a particular network
    Finally, the internal network specs on this device:
    1x 100Mb port on the Fritz!Box connects to a Cisco/LinkSys SLM2008 switch that connects to the VMs and the NAS
    It acts as a WLAN access point for mostly consumer devices (tablets, smartphones, etc.)
    DHCP is provided from Windows Active Directory domain controllers
    DNS is also from AD DCs
    "One ring to rule them all" -- ahem! -- one common subnet for all servers and consumer devices, incl. game consoles, blue-ray players, the above-mentioned tablets and smartphones, WiFi printers, etc.
    What I want to do (PLEASE tell me if I can't or if it's just too crazy):
    I want to put an ASA between the internal network and the edge
    I'd like to put VLANs internally, including one VLAN for client workstations, one VLAN for servers, and one VLAN for a Cisco lab, all on the (internal) "business" network
    I'd like network/application services to be able to pass from the "business" network through the ASA to both the "consumer" network and out to the Internet (and vice versa), including Exchange, Exchange web apps, access to a QNAP NAS, and access to an application running on SQL Server
    Longer-term I'd like to build a site-to-site VPN between this office and a remote site (has a Cisco 887), and I'd like to set up the VPN for direct client access from the Internet as well
    Longer-term I'd also like to create a DMZ and put the SMTP and HTTP servers there
    What equipment I have in addition to the servers/NAS:
    ASA 5505
    Catalyst 2960 for the server "farm"
    Cisco 881 ISR
    Right now everything works fine on the one common subnet. I tried splitting out the VLANs using the 881 and could ping everything from both sides but couldn't get the services to traverse to the "consumer" network, and, for example, couldn't get access from the Internet (or the consumer network) to the Exchange server. My Microsoft DNS also got messed up because of the subnet changes, though I think that was just a matter of letting things settle out for it to work. I was flummoxed.
    I know I should be using a simple DSL modem on the edge and connecting that to the ASA, but I'm pretty sure that I can't easily mess up my telephony from Deutsche Telekom and I would lose my WAP.
    Is there any way to keep this consumer network separate and add new VLANs/subnets for the business network? I actually have multiple PCs I'd like to have join the domain, but I can't really get there until I address this problem. I'd also like to get to lab devices over the Internet, even if that only means going through the 2511 terminal server.
    If you think I should break up this post -- separate it out -- and/or post it in multiple communities, I'd be happy to. Just let me know.
    Is there anyone who can help me with this thorny issue??
    Regards,
    jeremyNLSO
    P.S. I can post the configs from the attempt with the 881 and 2960 if it's helpful...

    Hello.
    Reading through the description I thought of the following topics:
     1. get rid off your current WAN VDSL device (or at least make it a bridge);
     2. configure your ASA for routing, making it WAN-faced;
     3. move your devices from current shared subnet to ASA.
    Regarding the topic 1 - I'm not sure if you could decommission the box, as it terminates you phone lines and also is provided as managed service. I believe you either need a dedicated service for telephony and ethernet link, or you may ask you provider how to configure the box as a bridge, so your ASA device could have public IP-address.
    I would recommend to buy static IP-address, so you wouldn't have to leverage on DynDNS. Also it might be worth to buy a subnet of public IP-addresses (like /29).
    Regarding the topic 2 - you may configure your ASA as WAN-facing device, configure NAT and routing for current shared subnet; also you may start configuring other subnets.
    ASA supports DNS doctoring, so it would be easier if you want to support split-DNS.
    Also if you need HA for ASA, you would better look for 5510 or 5515 device.
    PS: do not publish RDP service over NAT, as it's not safe! Always wrap RDP into VPN (ASA or router based) or SSL (RD Gateway).

  • Information on 3945 router and ASA 5520 FW

    Kindly help me.
    I requested for 3945 Router, to be equipped with advanced security IOS. On delivery, it came with only one power source, and no IOS license for the security feature.. All the ones i have seen on cisco site have two power sources. The vendor is claiming that it comes with one power source by default, and that the security feature does not need any license.
    Kindly confirm this to me.
    Secondly, the ASA firewall has a slot meant to be occupied by a flash-like PCMCIA card, but it is empty. Asking the vendor, he says the card is embedded in the interior of the chassis. Can this be true?
    I need you to help me with these clarifications.
    Thank you.

    Kindly help me.
    I requested
    for 3945 Router, to be equipped with advanced security IOS. On
    delivery, it came with only one power source, and no IOS license for
    the security feature.. All the ones i have seen on cisco site have two
    power sources. The vendor is claiming that it comes with one power
    source by default, and that the security feature does not need any
    license.
    Kindly confirm this to me.
    Secondly, the ASA
    firewall has a slot meant to be occupied by a flash-like PCMCIA card,
    but it is empty. Asking the vendor, he says the card is embedded in the
    interior of the chassis. Can this be true?
    I need you to help me with these clarifications.
    Thank you.
    Hi,
    If you have oredered with ios for cisco 3945 it should have pre loaded at the time of delvery and just check out the BOM at the time of order placement have order for dual power source for cisco 3945 router, As per the data sheet it has dual power supplies.
    http://www.cisco.com/en/US/products/ps10541/index.html
    Hope to Help !!
    Ganesh.H
    Remember to rate the helpful post

  • Inter VLAN Routing with ASA 5520 and Cat 2960

    Hi there,
    I am a complete novice at networking, but I was tasked to have an ASA 5520 do inter VLAN routing (since my shop doesn't have a layer 3 router).
    As a basic setup, I am trying to have three workstations on three different VLANs communicate with each other.  The attached screenshot shows the topology.
    I am unable to ping from a PC to the ASA...therefore I can't ping to other VLANs.  Any assistance would be greatly appreciated.
    ROUTER CONFIG:
    ciscoasa#
    ciscoasa# show run
    : Saved
    ASA Version 8.3(1)
    hostname ciscoasa
    domain-name null
    enable password ###### encrypted
    passwd ###### encrypted
    names
    dns-guard
    interface GigabitEthernet0/0
    no nameif
    no security-level
    no ip address
    interface GigabitEthernet0/1
    no nameif
    security-level 100
    ip address 10.10.1.1 255.255.255.0
    interface GigabitEthernet0/1.10
    vlan 10
    nameif vlan10
    security-level 100
    ip address 10.10.10.1 255.255.255.0
    interface GigabitEthernet0/1.20
    vlan 20
    nameif vlan20
    security-level 100
    ip address 10.10.20.1 255.255.255.0
    interface GigabitEthernet0/1.30
    vlan 30
    nameif vlan30
    security-level 100
    ip address 10.10.30.1 255.255.255.0
    interface GigabitEthernet0/2
    shutdown
    no nameif
    no security-level
    no ip address
    interface GigabitEthernet0/3
    shutdown
    no nameif
    no security-level
    no ip address
    interface Management0/0
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    management-only
    boot system disk0:/asa831-k8.bin
    ftp mode passive
    dns server-group DefaultDNS
    domain-name null
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    access-list global_access extended permit icmp any any
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu vlan10 1500
    mtu vlan20 1500
    mtu vlan30 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any inside
    asdm image disk0:/asdm-631.bin
    no asdm history enable
    arp timeout 14400
    access-group global_access global
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcpd address 192.168.1.2-192.168.1.5 inside
    dhcpd enable inside
    dhcpd address 10.10.10.101-10.10.10.253 vlan10
    dhcpd enable vlan10
    dhcpd address 10.10.20.101-10.10.20.253 vlan20
    dhcpd enable vlan20
    dhcpd address 10.10.30.101-10.10.30.253 vlan30
    dhcpd enable vlan30
    threat-detection basic-threat
    threat-detection statistics host
    threat-detection statistics port
    threat-detection statistics protocol
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns migrated_dns_map_1
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns migrated_dns_map_1
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip
      inspect xdmcp
      inspect ip-options
    service-policy global_policy global
    prompt hostname context
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DD
    CEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:4ad1bba72f1f51b2a47e8cacb9d3606a
    : end
    SWITCH CONFIG
    Switch#show run
    Building configuration...
    Current configuration : 2543 bytes
    version 12.2
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname Switch
    boot-start-marker
    boot-end-marker
    no aaa new-model
    system mtu routing 1500
    ip subnet-zero
    spanning-tree mode pvst
    spanning-tree extend system-id
    no spanning-tree vlan 1
    vlan internal allocation policy ascending
    interface GigabitEthernet0/1
    description Port Configured As Trunk
    switchport trunk allowed vlan 1,10,20,30,1002-1005
    switchport mode trunk
    interface GigabitEthernet0/2
    switchport access vlan 10
    switchport mode access
    interface GigabitEthernet0/3
    switchport access vlan 20
    switchport mode access
    interface GigabitEthernet0/4
    switchport access vlan 30
    switchport mode access
    interface GigabitEthernet0/5
    interface GigabitEthernet0/6
    interface GigabitEthernet0/7
    interface GigabitEthernet0/8
    interface GigabitEthernet0/9
    interface GigabitEthernet0/10
    interface GigabitEthernet0/11
    interface GigabitEthernet0/12
    interface GigabitEthernet0/13
    interface GigabitEthernet0/14
    interface GigabitEthernet0/15
    interface GigabitEthernet0/16
    interface GigabitEthernet0/17
    interface GigabitEthernet0/18
    interface GigabitEthernet0/19
    interface GigabitEthernet0/20
    interface GigabitEthernet0/21
    interface GigabitEthernet0/22
    interface GigabitEthernet0/23
    interface GigabitEthernet0/24
    interface GigabitEthernet0/25
    interface GigabitEthernet0/26
    interface GigabitEthernet0/27
    interface GigabitEthernet0/28
    interface GigabitEthernet0/29
    interface GigabitEthernet0/30
    interface GigabitEthernet0/31
    interface GigabitEthernet0/32
    interface GigabitEthernet0/33
    interface GigabitEthernet0/34
    interface GigabitEthernet0/35
    interface GigabitEthernet0/36
    interface GigabitEthernet0/37
    interface GigabitEthernet0/38
    interface GigabitEthernet0/39
    interface GigabitEthernet0/40
    interface GigabitEthernet0/41
    interface GigabitEthernet0/42
    interface GigabitEthernet0/43
    interface GigabitEthernet0/44
    interface GigabitEthernet0/45
    interface GigabitEthernet0/46
    interface GigabitEthernet0/47
    interface GigabitEthernet0/48
    interface Vlan1
    ip address 10.10.1.2 255.255.255.0
    no ip route-cache
    interface Vlan10
    no ip address
    no ip route-cache
    interface Vlan20
    no ip address
    no ip route-cache
    interface Vlan30
    no ip address
    no ip route-cache
    ip default-gateway 10.10.1.1
    ip http server
    ip http secure-server
    control-plane
    line con 0
    line vty 5 15
    end

    ciscoasa# capture cap10 interface vlan10
    ciscoasa# capture cap20 interface vlan20
    ciscoasa# show cap cap10
    97 packets captured
       1: 17:32:32.541262 802.1Q vlan#10 P0 10.10.10.101.2461 > 10.10.10.1.8905:  ud
    p 96
       2: 17:32:36.741294 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
       3: 17:32:36.741523 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
       4: 17:32:37.539217 802.1Q vlan#10 P0 10.10.10.101.2462 > 10.10.10.1.8905:  ud
    p 98
       5: 17:32:39.104914 802.1Q vlan#10 P0 10.10.10.101.2463 > 10.12.5.64.8906:  ud
    p 95
       6: 17:32:41.738914 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
       7: 17:32:41.739143 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
       8: 17:32:42.544023 802.1Q vlan#10 P0 10.10.10.101.2464 > 10.10.10.1.8905:  ud
    p 93
       9: 17:32:46.747352 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      10: 17:32:46.747580 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      11: 17:32:47.546633 802.1Q vlan#10 P0 10.10.10.101.2465 > 10.10.10.1.8905:  ud
    p 98
      12: 17:32:51.739921 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      13: 17:32:51.740150 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      14: 17:32:52.544100 802.1Q vlan#10 P0 10.10.10.101.2466 > 10.10.10.1.8905:  ud
    p 98
      15: 17:32:56.741859 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      16: 17:32:56.742088 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      17: 17:32:57.547396 802.1Q vlan#10 P0 10.10.10.101.2467 > 10.10.10.1.8905:  ud
    p 98
      18: 17:33:01.742728 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      19: 17:33:01.742957 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      20: 17:33:02.547609 802.1Q vlan#10 P0 10.10.10.101.2468 > 10.10.10.1.8905:  ud
    p 97
      21: 17:33:06.742774 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      22: 17:33:06.743018 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      23: 17:33:07.543337 802.1Q vlan#10 P0 10.10.10.101.2469 > 10.10.10.1.8905:  ud
    p 93
      24: 17:33:10.375514 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137:  ud
    p 50
      25: 17:33:11.114679 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137:  ud
    p 50
      26: 17:33:11.742728 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      27: 17:33:11.742957 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      28: 17:33:11.864731 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137:  ud
    p 50
      29: 17:33:12.546266 802.1Q vlan#10 P0 10.10.10.101.2470 > 10.10.10.1.8905:  ud
    p 98
      30: 17:33:16.746497 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      31: 17:33:16.746726 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      32: 17:33:17.548403 802.1Q vlan#10 P0 10.10.10.101.2471 > 10.10.10.1.8905:  ud
    p 97
      33: 17:33:21.744880 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      34: 17:33:21.745109 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      35: 17:33:22.545351 802.1Q vlan#10 P0 10.10.10.101.2472 > 10.10.10.1.8905:  ud
    p 95
      36: 17:33:23.785558 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137:  ud
    p 50
      37: 17:33:24.522464 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137:  ud
    p 50
      38: 17:33:25.272568 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137:  ud
    p 50
      39: 17:33:26.744926 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      40: 17:33:26.745154 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      41: 17:33:27.548708 802.1Q vlan#10 P0 10.10.10.101.2473 > 10.10.10.1.8905:  ud
    p 96
      42: 17:33:31.749625 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      43: 17:33:31.749854 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      44: 17:33:32.550096 802.1Q vlan#10 P0 10.10.10.101.2474 > 10.10.10.1.8905:  ud
    p 97
      45: 17:33:36.748343 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      46: 17:33:36.748572 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      47: 17:33:37.546251 802.1Q vlan#10 P0 10.10.10.101.2475 > 10.10.10.1.8905:  ud
    p 95
      48: 17:33:41.745566 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      49: 17:33:41.745795 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      50: 17:33:42.547975 802.1Q vlan#10 P0 10.10.10.101.2476 > 10.10.10.1.8905:  ud
    p 97
      51: 17:33:46.747855 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      52: 17:33:46.748084 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      53: 17:33:47.548403 802.1Q vlan#10 P0 10.10.10.101.2477 > 10.10.10.1.8905:  ud
    p 94
      54: 17:33:51.747718 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      55: 17:33:51.747931 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      56: 17:33:52.547670 802.1Q vlan#10 P0 10.10.10.101.2478 > 10.10.10.1.8905:  ud
    p 97
      57: 17:33:54.134239 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      58: 17:33:56.750678 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      59: 17:33:56.750891 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      60: 17:33:57.563035 802.1Q vlan#10 P0 10.10.10.101.2479 > 10.10.10.1.8905:  ud
    p 97
      61: 17:33:59.245272 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      62: 17:34:01.752188 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      63: 17:34:01.752402 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      64: 17:34:01.995737 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 49
      65: 17:34:01.995813 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 34
      66: 17:34:01.995950 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 49
      67: 17:34:01.996011 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 34
      68: 17:34:01.996118 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 49
      69: 17:34:01.996179 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 34
      70: 17:34:02.551836 802.1Q vlan#10 P0 10.10.10.101.2480 > 10.10.10.1.8905:  ud
    p 98
      71: 17:34:03.011306 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 49
      72: 17:34:03.011367 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 34
      73: 17:34:03.011443 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 49
      74: 17:34:03.011489 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 34
      75: 17:34:03.011550 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 49
      76: 17:34:03.011596 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 34
      77: 17:34:04.027037 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 49
      78: 17:34:04.027082 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 34
      79: 17:34:04.027174 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 49
      80: 17:34:04.027250 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 34
      81: 17:34:04.027311 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 49
      82: 17:34:04.027357 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 34
      83: 17:34:04.745811 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      84: 17:34:06.058514 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 49
      85: 17:34:06.058605 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427:  u
    dp 34
      86: 17:34:06.058651 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 49
      87: 17:34:06.058712 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427:  u
    dp 34
      88: 17:34:06.058758 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 49
      89: 17:34:06.058819 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
    udp 34
      90: 17:34:06.750907 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      91: 17:34:06.751151 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      92: 17:34:07.552751 802.1Q vlan#10 P0 10.10.10.101.2481 > 10.10.10.1.8905:  ud
    p 96
      93: 17:34:11.752082 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      94: 17:34:11.752326 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      95: 17:34:12.553392 802.1Q vlan#10 P0 10.10.10.101.2482 > 10.10.10.1.8905:  ud
    p 96
      96: 17:34:16.755438 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
      97: 17:34:16.755682 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
      98: 17:34:17.554811 802.1Q vlan#10 P0 10.10.10.101.2483 > 10.10.10.1.8905:  ud
    p 97
      99: 17:34:21.751303 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
    100: 17:34:21.751563 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
    101: 17:34:22.552034 802.1Q vlan#10 P0 10.10.10.101.2484 > 10.10.10.1.8905:  ud
    p 95
    102: 17:34:26.753989 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
    103: 17:34:26.754218 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
    104: 17:34:27.560334 802.1Q vlan#10 P0 10.10.10.101.2485 > 10.10.10.1.8905:  ud
    p 98
    105: 17:34:31.755499 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
    quest
    106: 17:34:31.755728 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
    ply
    107: 17:34:32.563950 802.1Q vlan#10 P0 10.10.10.101.2486 > 10.10.10.1.8905:  ud
    p 95
    107 packets shown
    ciscoasa# show cap cap20
    92 packets captured
       1: 17:26:53.653378 802.1Q vlan#20 P0 10.10.20.101.1187 > 216.49.94.13.80: S 8
    20343450:820343450(0) win 65535
       2: 17:27:12.019133 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
       3: 17:27:17.214481 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
       4: 17:27:55.593688 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
    499891746:1499891746(0) win 65535
       5: 17:27:58.555284 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
    499891746:1499891746(0) win 65535
       6: 17:28:04.564790 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
    499891746:1499891746(0) win 65535
       7: 17:29:06.504856 802.1Q vlan#20 P0 arp who-has 10.10.20.1 tell 10.10.20.101
       8: 17:29:06.504917 802.1Q vlan#20 P0 arp reply 10.10.20.1 is-at 54:75:d0:ba:4
    6:bb
       9: 17:29:06.505222 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
    7080594:47080594(0) win 65535
      10: 17:29:09.467032 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
    7080594:47080594(0) win 65535
      11: 17:29:15.476537 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
    7080594:47080594(0) win 65535
      12: 17:30:17.417245 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
    445997597:1445997597(0) win 65535
      13: 17:30:18.156043 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      14: 17:30:20.378688 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
    445997597:1445997597(0) win 65535
      15: 17:30:23.220356 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      16: 17:30:26.388102 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
    445997597:1445997597(0) win 65535
      17: 17:30:28.721047 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      18: 17:30:34.222507 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      19: 17:33:43.156928 802.1Q vlan#20 P0 arp who-has 10.10.20.101 tell 10.10.20.1
    01
      20: 17:33:44.187002 802.1Q vlan#20 P0 arp who-has 10.10.20.1 tell 10.10.20.101
      21: 17:33:44.187047 802.1Q vlan#20 P0 arp reply 10.10.20.1 is-at 54:75:d0:ba:4
    6:bb
      22: 17:33:44.187261 802.1Q vlan#20 P0 10.10.20.101 > 10.10.20.1: icmp: echo re
    quest
      23: 17:33:44.187520 802.1Q vlan#20 P0 10.10.20.1 > 10.10.20.101: icmp: echo re
    ply
      24: 17:33:44.239016 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      25: 17:33:44.327360 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
    udp 34
      26: 17:33:44.989740 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      27: 17:33:45.150611 802.1Q vlan#20 P0 10.10.20.101.6646 > 10.10.20.255.6646:
    udp 236
      28: 17:33:45.331312 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
    udp 34
      29: 17:33:45.740943 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      30: 17:33:46.331892 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
    udp 34
      31: 17:33:46.492131 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      32: 17:33:47.243502 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      33: 17:33:47.994501 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      34: 17:33:48.335050 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
    udp 34
      35: 17:33:48.335141 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
    udp 34
      36: 17:33:48.745658 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      37: 17:33:49.496861 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      38: 17:33:50.248812 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      39: 17:33:50.249300 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      40: 17:33:50.999170 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      41: 17:33:50.999246 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      42: 17:33:51.750342 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      43: 17:33:51.750418 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      44: 17:33:52.341336 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
    udp 34
      45: 17:33:52.341474 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
    udp 34
      46: 17:33:52.501576 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      47: 17:33:52.501652 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      48: 17:33:53.254183 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 174
      49: 17:33:53.254320 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 204
      50: 17:33:54.134361 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      51: 17:33:54.755118 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 174
      52: 17:33:54.823535 802.1Q vlan#20 P0 10.120.2.198.1261 > 161.69.12.13.443: R
    250934743:250934743(0) ack 2427374744 win 0
      53: 17:33:54.823901 802.1Q vlan#20 P0 10.120.2.198.1262 > 161.69.12.13.443: R
    3313764765:3313764765(0) ack 1397588942 win 0
      54: 17:33:54.824618 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
    2860571026:2860571026(0) win 65535
      55: 17:33:56.257448 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 174
      56: 17:33:57.759833 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 174
      57: 17:33:57.779729 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
    2860571026:2860571026(0) win 65535
      58: 17:33:59.245394 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      59: 17:33:59.262178 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 186
      60: 17:34:00.263780 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 186
      61: 17:34:01.265382 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 186
      62: 17:34:02.266908 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 186
      63: 17:34:03.268540 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      64: 17:34:03.789189 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
    2860571026:2860571026(0) win 65535
      65: 17:34:04.019591 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      66: 17:34:04.745933 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
    request
      67: 17:34:04.770757 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      68: 17:34:05.521991 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      69: 17:34:06.273209 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      70: 17:34:07.024367 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      71: 17:34:07.775518 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      72: 17:34:08.526706 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 68
      73: 17:34:09.277939 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 174
      74: 17:34:09.278061 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 174
      75: 17:34:09.278702 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138:  ud
    p 204
      76: 17:34:15.810489 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
    udp 31
      77: 17:34:16.809726 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
    udp 31
      78: 17:34:17.811222 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
    udp 31
      79: 17:34:19.814349 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
    udp 31
      80: 17:34:19.814380 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
    udp 31
      81: 17:34:23.820682 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
    udp 31
      82: 17:34:23.820788 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
    udp 31
      83: 17:34:30.822924 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 50
      84: 17:34:31.572892 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 50
      85: 17:34:32.324079 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137:  ud
    p 50
      86: 17:34:33.083079 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
    udp 44
      87: 17:34:34.077007 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
    udp 44
      88: 17:34:35.078639 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
    udp 44
      89: 17:34:37.081584 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
    udp 44
      90: 17:34:37.081706 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
    udp 44
      91: 17:34:41.087809 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
    udp 44
      92: 17:34:41.087840 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
    udp 44
    92 packets shown

Maybe you are looking for

  • Direcrt GL account activation restriction to specific PO's

    Dear All, We have activated the direct GL account posting(G/L account tab), which tab appears in MIRO. Can we restrict this GL account tab appearence for specific PO types only? Please suggest the possibilities. Regards

  • How do i insert into temp table

    Hi ALL, I have a table APP APP_I Acronym Desc 1 ACC Accounts PLTFRM swr_pltfrm_i swr_pltfrm_x swr_pltfrm_typ_x 1 AIX-JAVA Execution 2 COBOL/BATCH Execution 3 COBOL/CICS Execution 4 CONSULTWORKS/MOBILE Delivery 5 CONSULTWORKS Delivery PLTFRM_APP_ENVT

  • Fullscreen Video Playback, from Button? Video Question

    I have used the external URL to link directly to a video and it opened in an HTML window, not just fullscreen. I would like to emulate what is seen in this example. LINK: http://youtu.be/-YMyQZki0bY?hd=1&t=1m2s

  • Order of expression in where clause matters

    Connected to: Oracle8i Release 8.1.5.0.0 - Production With the Java option PL/SQL Release 8.1.5.0.0 - Production SQL> select * from dual where 1 = 1 or 1/0 < 1; D X SQL> select * from dual where 1/0 < 1 or 1 = 1; select * from dual where 1/0 < 1 or 1

  • Can we connect the ipads with Oracle ERP ?

    if we have an Oracle ERP system which is has a sets of HR apps. can we make the iPad as authorized client admin on this system ? please, if you can link me to more information about this subject. good day