Stuck on Bios screen after GPU upgrade

Hello,
I own a HP Pavilion HPE h8-1024ch (http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&lc=en&os=4132&product=5144367). I've replaced the GTX 550 ti with a Gigabyte GTX 760 (http://www.gigabyte.com/products/product-page.aspx?pid=4935) and when I power on the computer, the screen get stuck on the bios.
Is there a new bios update for my computer or how can I fix it?
The problem don't come from the power supply, I changed it for a Corsaire 850Watts.
(sorry for my english, I speak french)
Thank you in advance for your answers.

Hi,
Most if not all NVIDIA GTX 760 graphics cards will not work in your PC.  Return the graphics card and try the NVIDIA GTX 660.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Similar Messages

  • MacBook Pro stuck at grey screen after Yosemite upgrade

    upgraded to yosemite yesterday. Reboot and stuck at grey screen(login in page) when i log in there is some codes thing at the left top corner of the screen. and then it reboots again. Which means I can never log onto the computer. what should I do

    If you can't start up and log in in the usual way, try in safe mode.
    During startup, you’ll see a progress bar, and then the login screen, which appears even if you normally log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Log in as an administrator to carry out these instructions. If you have only one account, you are the administrator.
    ☞ If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
    Safe mode is slower than normal, and some things won’t work at all.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t start in safe mode.
    If you're able to log in, launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    In the Console window, select
              DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
    (not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar.
    There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
    I know the report is long, maybe several hundred lines. Please post all of it anyway.
    In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
    Please don’t post other kinds of diagnostic report.

  • Stuck at login screen after Yosemite Upgrade - 2013 27" imac won't recognize keyboard or mouse

    I installed yosemite without issues on my 2013 macbook pro retina so decided to try it on my 2013 27" imac. Install went fine until I get to login screen. Wireless keyboard and mouse won't pair so I can't type in password. Connected generic wired keyboard and mouse and still won't recognize it.
    However, when I restart it I can hold down option on keyboard and it will bring up list of hard drives to boot from (I also have windows installed with bootcamp) so I know imac pairs the key

    So the iMac was purchased by my father in 2011 shortly before he died.  I thought, why not check if he also purchased Applecare at the same time? Turns out he did! So after calling and trying to reset the SMC, etc. with it not working the Apple tech told me to turn it over to an authorized repair shop here in Louisiana.  Hopefully they can fix it.

  • Lenovo G560 - Issue with won't boot and black screen after HDD upgrade

    Lenovo G560 - Issue with won't boot and black screen after HDD upgrade.
     What happen: My laptop was working fine, no blue screen issue, no funny business at all. I bought a new SSD Intel 120 GB and thought it would be a good idea to replace the HDD. I shutdown and disconnected the power adapter, waited a couple of minutes and removed the battery. I opened up the back case and replaced the HDD. And put all the screws back and put the battery back in.
    Problem: The very first time I turned the power on, nothing happens besides a black screen. I pressed the dvd drive it works and opens up and closes. I waited for about 30 mins and still has blac screen. When I mean black screen, no bios menu, no logo, just a black screen with the fan sound on.
    I have tried these:
    1. Unplugged everything - battery, adapter, and pressed the power on button for about 60 seconds, nothing, the laptop turns on with the LED display on for both on and battery LED's. But nothing but black screen, no sound of windows loading just the fan and black screen.
    2. I tried putting back my old 2.5" and nothing but black screen.
    Thoughts and suggestions?
    Solved!
    Go to Solution.

    Hi Autoexit173,
    Welcome to Lenovo Community!
     As per the query we understood that you are facing issue with system not booting in your Lenovo G560 laptop.
    As you have mentioned that the system not booting, please try to remove the RAM and  turn on the system and check if you can hear any beep sound. Also try to clean the RAM slots and check for the issue.
    Click here for the steps to remove the RAM and refer page number 40.
    Hope this helps. Do post back if issue persists!
    Best regards,       
    Ashwin.S
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • I am trying to load photos from my computer on to my ipad but keep getting the message "the device is no longer connected to the computer. It keeps popping up and I am stuck. This happened after I upgraded to the latest itunes

    I am trying to load photos from my computer on to my ipad but keep getting the message "the device is no longer connected to the computer". It keeps popping up and I am stuck. This happened after I upgraded to the latest itunes software.

    Greetings cdewinkel,
    It seems your iPad is not staying connected to your computer during syncing. The following article provides a number of troubleshooting steps which may help. This article is intended for devices which are not being detected, but the troubleshooting steps are relevant to your issue:
    If you don't see your connected device in iTunes for Mac - Apple Support
    Make sure that your device is on
    Also make sure that you can get to the Home screen.
    Get help if you have one of these issues:
    Your iOS device won't respond or turn on.
    Your iPod won't turn on.
    You forgot your passcode or your device is disabled.
    Make sure that your Mac supports your device
    See the system requirements for iPhone, iPad, or iPod.Check your USB connections
    Unplug other USB devices from your Mac and try again.
    Try a different USB port.
    Try a different USB cable. 
    Learn more about using USB cables with your Mac.Make sure that your device trusts the computer
    You might get an alert if you haven't connected your iOS device to this computer before. Unlock your device and tap Trust. 
    Learn more about the Trust This Computer alert.Restart your device
    Restart your iOS device or reset your iPod.Restart your Mac
    Turn your Mac off and back on.Update your software
    Check for software updates on your Mac.
    Check for an iTunes update.
    Check your security software
    If you have security software installed, learn how to resolve issues between iTunes and your security software. 
    Get more help
    If you still don't see your device in iTunes, contact Apple Support.
    Thank you for contributing to Apple Support Communities.
    Best,
    Bobby_D

  • HT201263 iPod touch 4th gen stuck on apple screen after trying to update ios 6

    iPod 4th gen stuck on apple screen after I tried updating to IOS 6. It won't turn off or reset even after updating iTunes to latest version. My iPod doesn't show up when I connect to iTunes. HELP PLEASE!

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • 27" 2009 iMac is stuck on white screen after OS X Maverick update

    27" 2009 iMac is stuck on white screen after OS X Maverick update.  How do I get past this White Screen?  I have tried to use the PRAM reset, holding down Shift,Command, R, and P after turning off computer then when I turn it on, having those pressed until I see the apple symbol.  I only hear one chime. Never get to a second chime.  Thank you.

    Startup - Gray, Blue or White screen at boot, w/spinner/progress bar
    Startup - Gray Screen
    Startup Issues - Resolve
    Startup Issues - Resolve (2)

  • HT4623 Hi, I am suck on the Terms and Conditions screen after the upgrade and have agreed, but I am not progressing further from this sceen after agreeing? What do I need to do?

    Hi, I am suck on the Terms and Conditions screen after the upgrade and have agreed, but I am not progressing further from this sceen after agreeing? What do I need to do?

    Have you tried resetting (Hold the Sleep/Wake and Home buttons and don’t let go until the screen goes dark and the Apple logo appears) and starting the set up again?

  • My MacBook pro is stuck on white screen after shut down. Now, neither this is turn on nor turn off. I had to do

    My MacBook pro is stuck on white screen after shut down. Now, neither this is turn on nor turn off.

    You should be able to turn off your MBP by pressing the power button down continously for about 5-10 sec. When you reboot it you are going to want to enter into a terminal screen. Hopefully the following YouTube video helps: http://www.youtube.com/watch?v=qKOX72xNmbo

  • IMAC intel A1208 is stuck on blue screen after start-up. What is the fix?

    IMAC intel A1208 is stuck on blue screen after start-up. How can this condition be resolved?

    Please carefully read Apple's Gray screen appears during startup

  • Lenovo B570 Stuck at bios screen

    I have a B570 that I recieved with a cracked LCD.  Upon replacing it everything powers on just fine however I cannot get into the bios.  When I press F2 it just says please wait in the bottom corner but never enters the BIOS.  Furthermore it will not go past the bios either.  The progress bar on the bios splash screen will get about half way done then just hang.  I have tried booting without the hard drive and it does the same thing.  It never gets past the BIOS screen.  There are no beeps or anything.

    Hi theath6123,
    You may want to try removing the RAM on your computer just to check if the system would beep. Also you may want to try reseating your RAM. Please exercise caution while doing this and please follow the rules listed under Chapter 7. Removing and replacing a FRU under page 45 of hardware and maintenance manual.
    See if reseating the RAM allows you to go into the bios options. After that you can put in the HDD back and see if it is detected under the bios. From there you can try to boot to windows from your hard drive.
    Listed below is the link for the hardware and maintenance manual:
    B570 manual
    Let me know if this helps.
    Don

  • Photoshop Crashes after GPU Upgrade

    I just recently upgraded my GPU from an nVidia GTX 460 to an AMD Radeon R9 290, and since then I've been experiencing problems with Photoshop.
    Just after I upgraded my GPU, I did a clean uninstall of my old drivers, installed my new drivers (which I also updated to the latest version [13.12] just today), and tried using Photoshop.
    At first, I was prompted with an error dialog saying that Photoshop could not detect my graphics card, so it has disabled OpenGL support.
    I ignored the error, and proceeded to editing an image, but after a few actions Photoshop crashed, prompting me with the 'Photoshop has stopped working' windows dialog.
    After restarting Photoshop, I went to Edit -> Preferences -> Performance and checked the GPU Settings box, which was now grayed out.
    When hovering over it, Photoshop displayed a notification saying that there is a problem with my Display Driver, and that I should re-install it.
    I re-installed my graphics driver, tried several different versions too, re-installed Photoshop, did a clean uninstall (with the help of the Adobe Clean tool) and re-install, but none of these actions helped.
    While I was in safe mode (for cleaning up my GPU drivers), I launched Photoshop and realized that even though it told me that there was an error with my drivers, it would work just fine, without crashing after executing a few actions.
    I also checked the Help -> System Info dialog for possibly obtaining additional information about the error, but the only relevant thing I can see is 'The GPU Sniffer crashed on XX/XX/XXXX at XX:XX:XX'.
    I find this weird, because when I manually run the sniffer, it simply exits after printing 'snifferStart="XXXX-XX-XX_XX:XX:XX"'.
    The last thing I tried doing was renaming sniffer.exe to something different.
    This resulted in Photoshop re-enabling the GPU Settings box (but obviously saying that there is no GPU detected), and getting rid of the weird crashes.
    However, it also resulted in various other glitches, like the main view not updating, the layer previews not properly working, etc.
    Finally, I should note that I tried using both Photoshop CS6 (which I initially had installed), and a trial version of Photoshop CC.
    My system specs are the following:
    OS: Windows 8.1 (64 bit)
    RAM: 16GB DDR3
    CPU: Intel i5 3570K
    GPU: AMD Radeon R9 290
    Secondary GPU (Onboard): Intel HD 4000 Series
    Currently Installed Photoshop Version: Photoshop CC 14.1.2 (x64)
    Any help would be greatly appreciated.
    Thanks in advance!

    I noticed the same problem if I had my two R9 290s in Crossfire mode. If I turn off Crossfire, I get no error.
    HOWEVER, as I have just upgraded from 2 GTX580s, and I do a lot of professional digital painting, I noticed using my Wacom Intuos5 (I usew the Cintiq 24HD with GTX580 at work), there was heaps of lag in painting with a standard brush. If I just did a slow stroke, the 'paint' would be lagging behind the brush 5-10mm onscreen. I tried setting the 'Use Graphics Processor' down to Normal and Basic, and it got worse. I turned 'Use Graphics Processor' off completely and there is no real discernible lag, feels very natural as with the Nvidia cards. However, because this is turned off, I loose any GPU 'accelerated' advantages like animated zoom etc.
    My setup:
    Catalyst Software Suite: 13.12
    Display Driver ver. 13.11
    OpenGL(tm) Driver ver. 6.14.10.12618
    Catalyst Control Center ver. 2013.1206.1603.28764
    i7 2600K @ 4428Mhz | Asus p8z68 Deluxe | 8GB RAM | 2 x Gigabyte R9 290 | X-Fi Ti | 5TB | Silverstone Strider 1500W | SilverStone FT02B Fortress | Win7 64bit | ASUS VG236H 23" 3D LCD x 3 | Logitech G19 KB and G9 Mouse

  • Crash on the account screen after an upgrade

    Hi experts.
    We have made recently an upgrade from CRM 5.2 to 6.0 and we have some errors.
    For example, we can't no longer access the Individual account creation screen, 3 exceptions are raised.
    Cannot display view MainWindow
    An exception has occurred Exception Class  CX_BSP_WD_INCORRECT_IMPLEMENT - The view controller or custom controller "" was implemented incorrectly 
    Method:  CL_BSP_WD_COMPONENT_USAGE=>IF_BSP_WD_COMPONENT_USAGE~BIND_CONTEXT_NODE 
    Source Text Row:  24
    An exception occurred during the activation of target view Overview.MainWindow for the navigation
    An exception has occurred Exception Class  CX_BSP_WD_RUNTIME_ERROR - View Overview.MainWindow could not be bound 
    Method:  CL_BSP_WD_VIEW_CONTROLLER=>BIND_VIEW 
    Source Text Row:  162
    An exception occurred during the activation of target view Overview.MainWindow for the navigation
    An exception has occurred Exception Class  CX_SY_REF_IS_INITIAL - Dereferencing of the NULL reference 
    Method:  CL_BSP_WD_VIEW_MANAGER=>HANDLE_FOLLOWUP_NAVIGATION 
    Source Text Row:  6
    For the first exception, I have debugged the system and here is what happens. In the BP_HEAD_MAIN component controller (method WD_USAGE_INITIALIZE), at one point, the
    system retrieves the context nodes available and the context node
    MESSAGEFILTER is not retrieved. That's why an exception is raised.
    The error occurs in the following bloc of code of the :
    class : CL_BP_HEAD__BSPWDCOMPONE1_IMPLCM001
    method : WD_USAGE_INITIALIZE
    CALL METHOD lv_usage->bind_context_node
    EXPORTING
    iv_controller_type = cl_bsp_wd_controller=>co_type_component
    iv_target_node_name = 'MESSAGEFILTER'
    iv_node_2_bind = 'MESSAGEFILTER'.
    Inside the bind_context_node method, when the system tries to get the
    context node (IF_BSP_WD_COMPONENT_USAGE~GET_CONTEXT_NODE), MESSAGEFILTERis not included in the table LT_ALLOWED_NODES
    Does anyone have a clue on how we can correct this ?
    Thanks in advance for your help.
    Regards.
    Helder.

    Helder,
    All you need to do is readjust the repository.xml file after you copied in the standard so that your navigation link or viewset addition changes are put back in.  If you never added a new view to the component or changed the navigation links or did any manual edits to the repository.xml then a straight copy will work.
    For example say you enhanced BP_HEAD and stored the enhancements in ZBP_HEAD.  You need to copy the respository.xml file in BP_HEAD over to ZBP_HEAD after the upgrade.  Then you need to reinsert any navigation links,component usages, etc, that you added in CRM 52.  That will then get your component back to standard.  You can also "turn-off" your enhancements by de-assigning the enhancement set to the client and run the "standard roles" to see if your issue is fixed.
    Take care,
    Stephen

  • Stuck at grey screen after reboot

    I seem to be stuck at the grey screen after a reboot of my server. Here are the symptoms and I'm wondering if anyone has experienced them before or has some idea of where to look:
    1) Over the last couple of weeks, I've noticed the entire system freezing up for 10-20 seconds. The spinning pinwheel pops up and when my office is really quite, it sounds like either a fan is starting on the system or a hard drive is spinning up. Note that I've turned off all 'spin drives down when possible' in energy savings.
    2) After the 10-20 seconds, a bunch of disk activity occurs and everything goes back to normal.
    I've tried repairing permissions, checking for errors with the drive, etc. I've got two drives striped in Raid 0 (yes, the system is backed up--so I'm not worried about loosing data).
    After a recent software update, I had to reboot it, and that's where it got stuck. Could be something there for some time, but my server usually runs for months at a time, unless an update requires a reboot.
    Thanks for any help or suggestions!

    Could you be more specific about what disks you used to boot with and exactly what programs you ran...
    I cannot seem to get it to boot from the "Admin Tools" disk using the "D" key.
    Also, when booting from the "Mac OS X Server" disk I can access Disk Utility, but do not see Raid Utility anywhwere.

  • Stuck at preloading screen after failed reboot with cd

    I am stuck at the preloading screen after i got the "something was wrong during reboot from cd message", but now i can't seem to reboot from the cd by pressing "c" after startup, nor go into safemode by pressing "shift" or hardware by "d", i just go onto the preloading screen for 20+ mins and nothing happens...

    Hi d,
    You can try an SMCReset: http://support.apple.com/kb/HT3964
    If that doesn't help, it might be time for a "genius" bar appointment. Was the optical drive working ok? Does the DVD look ok? Is it the proper one for your MBP? What issues were you having prior to this that made you decide to boot from the disc?

Maybe you are looking for