Sunfire 280R and Remote System Control (RSC)

I have a sunfire 280R machine, and I was wondering if RSC can be loaded onto it. The sunfire page says that it can, but the RSC page lists much newer models as system requirements for the software.
Also can anyone tell me if the RSC provides a windowing environment for the machine (i've been trying to figure out how to get remote access to a linux windowing environment without much success. I've installed cygwin/x on my windows computer)
Thanks!

Hello,
as the name implies the RSC allows to control and monitor the system from remote via serial or ethernet.
The lastest version can be downloaded from
http://www.sun.com/servers/rsc.html
I'm running RSC 2.2.3 on an E250 (the F280R and the other systems listed on the above page are supported as well).
Also can anyone tell me if the RSC provides a windowing environment for the machine. (i've been trying to figure out how to get remote access to a linux windowing environment without much success. I've installed cygwin/x on my windows computer).
No, it just the client/server application to communicate with the RSC hardware.
Michael

Similar Messages

SUN Remote System Control software

I doubt this is the correct forum, however I cannot find a more suitable one.
Recently my Windows XP PC, refuses to allow the RSC software to work.
When I attempt to run RSC it displays the following message:
"*Remote System Control requires the Java Runtime Environment version 1.3.0 or later"*
My PC is running with Java version 1.6.0_14-b08, I have tried installing older versions of Java but it still fails to work.
Does anyone have any idea what I have missed here?
Many thanks
Neil

Hello Neil,
please review the following thread.
[Information regarding using the RSC 2.2.3 GUI on Windows with JRE > 1.5 |http://forums.sun.com/thread.jspa?forumID=830&threadID=5348513]
If your system is under system contract you can file a RFE (request for enhancement) or report a bug. At least choosing this check was not very clever (certain versions instead of the minimal required version) !
Maybe Sun argues that the windows binary rsc.exe was only tested with with JRE 1.3, 1.4 and 1.5.
Michael
Edited by: MAAL on 09.07.2009 18:51
Corrected a typo in my post from 06.07.2009 22:16. Due to a forums bug the original date of posting is lost after editing.

Create DB link between my local system and remote system

Hi,
I need help to create DB link between my local system Database and remote system database both the database are oracle.
Please check the script which i have written is correct or not. Its giving me error sql command not ended properly
create public database link MERU_PROD_LOCAL_PROD
CONNECT TO SUDHIR
identified by sudhir123
using (DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS =
(COMMUNITY = tcp.world)
(PROTOCOL = TCP)
(Host = 23.23.150.144)
(Port = 1521)
(CONNECT_DATA = (SERVICE_NAME = sudhir)
I am executing this command in my local system connecting to the remote database link. Please suggest me is this method correct.
Thanks
Sudhir

Hi Hilton,
I fixed that issue. Now i am creating the DB link this ways please check is this proper or not
create or replace database link meru_prod_local_prod connect to portal identified by Oracle!123 using 'MERUPROD';
remote machine
User Name: portal
Password : Oracle!123
MERUPROD is the tnsora entry
It gives error as
Error starting at line 1 in command:
create or replace database link meru_prod_local_prod connect to portal identified by Oracle!123 using 'MERUPROD'
Error at Command Line:1 Column:18
Error report:
SQL Error: ORA-00922: missing or invalid option
00922. 00000 - "missing or invalid option"
*Cause:
*Action:

Search for [Remote Key] and [Remote System] in Data Manager

Hello all
I would like to be able to search on the remote key and the remote system in the MDM Data Manager is that not possible? I thought I remembered seeing that possibility under the Free-Form Search but now I can't find it.
I have, however, found this in the Data Manager reference guide:
REMOTE SYSTEM AND REMOTE KEY FIELDS
MDM uses the remote systems defined in the Remote Systems table
within the MDM Console to store and maintain key mapping information
for each record or text attribute. It does this using a virtual key
mapping field that you never see in the MDM Client.
This virtual key mapping field is very much like a qualified lookup field
into a virtual key mapping qualified lookup table.
Key Mapping information stored in virtual lookup field
The Remote System and Remote Key fields are normally not visible;
however, they do appear in several places in the MDM Client.
Specifically, both fields: (1) appear in the File > Export dialogs in Record
mode for exporting value pairs; (2) are recognized by the File > Import
dialog in Record mode for importing value pairs; and (3) appear in the
Edit Key Mappings dialogs in both Record mode and Taxonomy mode,
for viewing and editing value pairs.
Is there any way to search on the value in the remote key from the Data Manager?

Not sure search i think not possible.
But you can see keys as mentioned:
Enable Key mapping in Console.
MDM Client maens MDM Data Manager.
They do appear in several places in the MDM Client or Data Manager. Three different methods to see in DM are given already below:
Specifically, both fields: (1) appear in the File > Export dialogs in Record mode for exporting value pairs; (2) are recognized by the File > Import dialog in Record mode for importing value pairs; and (3) appear in the Edit Key Mappings dialogs in both Record mode and Taxonomy mode, for viewing and editing value pairs.
BR,
Alok

PT880 and System Control Utility

I do the Live Update feature with my two MSI boards-----great feature----wish ALL mobo companies had something like it!
Anyway----yesterday on my PT880 rig----it wanted me to update Live Update to Version 3.60 and now offers me another Utility called "System Control"
Neither of those are actually on MSI site in the PT880 motherboard download section.
Anybody know what "System Control" is or does??
I tried to load it but continued to get errors....
John

It shows up as a downloadable utility from within Live Update----when I do Live Monitor-----and it goes up to MSIs site and checks for latest Bios, drivers, and utilities.
I used to only be able to download eight different utilities, Core Center being one of them---LockBox, iSpeeder, GoodMem, WMI Viewer etc.
But now, two more are showing up----Playlist Editor and System Control.
And neither of those two show up in the actual download site for the PT880 Neo on the Taiwan site. In fact----the Taiwan Site is showing the latest version of Live Update to be 3.58------and a message came across my screen recommending that I update Live Update to ver 3.60----which I did.
When I download and install System Control----I get a "Port not found" error---and it won't do anything.
Strange......

Backupeventlog not working for remote system in PowerShell

I have the following code snippet that works if I specify localhost or the name of the local computer, but does not work if set to a remote server. I am running the script as Administrator using my Domain Admin account. Both local and remote systems
are Windows Server 2012 and in the same domain. PowerShell version = 3.0.
Param(
[parameter(Mandatory=$true,ValueFromPipeline=$true)]
[ValidateScript({Test-Connection $_ })]
[String]
$Server,
[parameter(Mandatory=$true,ValueFromPipeline=$true)]
[String]
$LogFileName,
[parameter(Mandatory=$true,ValueFromPipeline=$true)]
[ValidateScript({Test-Path $_ -PathType 'Container'})]
[String]
$OutputFolder
$EventLog = Get-WmiObject win32_nteventlogfile -ComputerName $Server -Filter "LogFileName = '$LogFileName'" -ErrorAction SilentlyContinue -ErrorVariable $ResultError
If ($ResultError)
Write-Host "ERROR: unable to event logs from $Server."
} Else {
Write-Host "Backing $Server."
$EventLog.backupeventlog("$OutputFolder\$Server.evtx")

After spending some more time troubleshooting this and doing some more research I found the link below. I found it strange the hoops the author went through to handle event logs on remote systems until I realized that the path for "backupeventlog"
is relative to the remote system, not the system running the script. So I checked the other systems and found that the event log backups had been created. This would explain the returnvalue of 80. What's worse is that the path for "backupeventlog"
can't be a UNC -- I tried, it didn't work.
Back Up Your Event Logs with a Windows PowerShell Script
https://technet.microsoft.com/en-ca/magazine/2009.07.heyscriptingguy.aspx
I decided to re-read Microsoft's documentation and found the magical text that I had over-looked:
BackupEventlog method of the Win32_NTEventlogFile class
https://msdn.microsoft.com/en-us/library/aa384808(v=vs.85).aspx
In addition, you must make backups to the local computer; you cannot save a backup of the event logs on Computer A to Computer B. Backups are implemented by using the LocalSystem account, which does not have the network credentials necessary to access remote
computers. If you want to save backups to a central repository, modify the script to first perform the backup, and then move the backup file to the central repository.
jrv:
I would mark your post of Wednesday, March 04, 2015 9:45 PM as helpful if this option were available. Your comment got me to dig into this deeper and discover
the root cause.
Thanks.

Change remote system in sydnicator map

I have imported a syndication map from a remote system and want to duplicate the same map out to another remote system, how can i change the remote system value in the map properties?
Adam Sellers.

Hi Adam,
When you are opening the MDM syndicator. Go to .. File>Connect to source
Here you can mention the Type and Remote system.The Remote system you select here gets reflected in your Map properties.
Now import The Exported Map.
Hope it helped
Thanks & Regards
Simona Pinto

No OK prompt RSC PGX32 Sunfire 280R

This is a bit chicken and egg.
I have just installed a second hand PGX32 graphics into a sunfire 280R that has previously been administered by RSC. How (please be verbose) do I get the server to output to the graphics card? I don't know how to get to the OK prompt using RSC to turn off RSC! I also have a USB keyboard and mouse. I am using the RSC gui client on windows and connecting to RSC using ethernet. Telnet to RSC works but I assume I can't telnet to the OK prompt?
Thanks,
Tim.

Yes, you can telnet to the ok prompt.
Once you are the rsc prompt type "console" to get to the ok prompt (assuming its not booted).
If its booted, you'll need to type "break" first.
Type "~." to get back to the rsc from the console
Personally I would leave the console on the rsc as its the most useful configuration for remote management.
But if you do want to change it, you need to do
setenv output-device screen
setenv input-device keyboard
Alternatively, you can do the same thing from the os level using the eeprom command.

Remote Control and Remote View Problem

Hi,
I work at a High School running Netware 6.0 SP5 and Zen works 4.01 ir7.
Remote Control and Remote View works great but I noticed one problem.
We have a logo of the school that is forced down on to the desktop when a
user logs in through group policies. This logo works perfect for the
desktop wall paper and loads every time a user logs in.
When I Remote Control or Remote View a computer the users desktop wall
paper turns from the logo being forced down through group policies to the
desktop to a blue desktop wall paper.
I would prefer the desktop wall paper staying the schools logo when I
Remote Control or Remote View because if the desktop wall paper changes to
the blue color I mentioned above when I Remote Control or Remote View the
users computer, they will know that someone is taking over their computer
which sometimes we dont want them knowing.
We have Windows 98SE computer running Novell Client 3.4 and we have some
computers running Windows XP Professional SP1 and Windows XP Professional
SP2 both running Novell Client 4.91 SP2.
The Remote Control and Remote View problem of the desktop wall paper
changing on the users computer occurs on all operating systems mentioned
above.
Is there a solution to my above problem? When Remote Controlling and
Remote Viewing someone's computer I don't want the desktop wall paper to
change.
Thanks!

Bpilon,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at
http://support.novell.com.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

ARD Hangs/Stops Responding when trying to "control" a remote system

I'm having the toughest time with a new setup for a client. Recently the client purchased 3 brand new Mac Mini systems, and I purchased a Sandy Bridges MBP 13".
After configuring the network and installing the Mac Mini's, I setup ARD so that I could remote desktop in to the systems for remote assistance and support. We purchased the Apple Remote Desktop administrator software from the Mac Store ($79.99 application). The administrator software seems to work great up until the point I try to "control" the remote device. I can schedule tasks, create remote users, modify files, remote upload/download files, and even observe or curtain the remote system. However, as soon as I click on "control" or start the session as observe and then attempt to take control of the remote system, ARD hangs and I'm forced to quit.
I have attempted a fresh installation on all systems to see if there was something cooky that happened, and I'm always exhibiting the same problem.
Does anyone have any suggestions of where to start? I feel like a fool, as I've spent $80 on a piece of software, that is absolutely useless to me as an IT admin... :\
I appreciate any ideas!
Regards,
Jordan W.

...unfortunately the only way I was able to fix the problem was to re-format and fresh install the administrator computer.
I'm going to mark as answered, even though it was not.

Software Systems Engineer (LV, LV RT, LV FPGA, CVI TestStand, Veristand, C/C++) available for full/part time and remote project work

I am a software engineer with lots of experience in embedded and test systems. I am a certified TestStand developer, and recently finished a cRIO based embedded system for a medical device company using LV RT and LV FPGA. I have done a lot of TestStand customization and APIs to HIL and other test equipment and created my share of Windows/Linux based C++ applications and libraries.
I am located in Southeast Michigan and interested in both local and remote project work, as well as full or part time employment.
I will be at NIWeek 2010 on Wednesday and Thursday. I am holding a session on Simple TCP/IP messaging on Thursday.
If you would like to meet during NIWeek and/or request my resume please email me at [email protected]

I saw your posting on the LabView discussion forum concerning your need for a LabView Software Systems Engineer.
I am a consultant and I am currently available for contract work.
I have done the things you describe as experience you would like to have.
I have attached a "Fact Sheet" which describes some of the systems I have built.
You will notice that I am experienced with developing hardware systems and controls as well as software systems..
I have over 20 years of experience developing these kinds of systems and have worked with many different kinds of hardware/computer interfaces as well as numerous different software environments.
If you are interested in discussing this further please call or email me.
Tom Moser
ForMost Systems
North Canton Ohio
330-470-0404 begin_of_the_skype_highlighting 330-470-0404 end_of_the_skype_highlighting x202
email: [email protected]
Attachments:
IS 071410a .pdf ‏253 KB

Startup taking too long and remote control

Hi,
today i used this cocktail software to run routine maintenance on my iMac G5(10.5.1), after the the software did it's thing issues started popping up
1. the initial start up sound the one when the light comes on, stays on for like 3 mins with a blank screen.
2. in the security pref. the apple remote control option has suddenly disappeared and the remote does not work, the remote it's works with my hi-fi and macbook so i am really lost i don't know what i have done
pls help

Yes i used the cocktail compaitble with leopard. the system appears to be working fine now but before that it displayed temp madness.
i tried to reset the system with cmdopt+PR, it took 2 mins for it to realize i was even pressing the keyboard when it finally did the fan went full power for a couple of seconds (the ambient light still on) and the system shut down. i tried to start it up again it will make the startup noise then shutdown i did that 5 times until i removed all the cables connected to it before it came back on. it started got to the desktop but 2 hardware's were disabled, USB's ports and the audio driver had to restart again.
now i am afraid to shut it down.

Remote System and Remote Key Mapping at a glance

Hi,
I want to discuss the concept of Remote System and Remote Key Mapping.
Remote System is a logical system which is defined in MDM Console for a MDM Repository.
We can define key mapping enabled at each table level.
The key mapping is used to distinguish records at Data Manager after running the Data Import.
Now 1 record can have 1 remote system with two different keys but two different records cannot have same remote system with same remote key. So, Remote key is an unique identifier for record for any remote system for each individual records.
Now whenever we import data from a Remote System, the remote system and remote key are mapped for each individual records. Usually all records have different remote keys.
Now, when syndicating back the record with default remote key is updated in the remote system that is sent by xml file format.
If same record is updated two times from a same remote system, the remote key will be different and the record which is latest contains highest remote key.
Now, I have to look at Data Syndication and Remote key.
I have not done Data Syndication but my concept tell if there is duplicate record with same remote system but different remote keys both will be syndicated back. But if same record have two remote keys for same remote system then only the default remote key is syndicated back.
Regards
Kaushik Banerjee

You are right Kaushik,
I have not done Data Syndication but my concept tell if there is duplicate record with same remote system but different remote keys both will be syndicated back.
Yes, but if they are duplicate, they needs to be merged.
But if same record have two remote keys for same remote system then only the default remote key is syndicated back.
This is after merging. So whichever remote key has tick mark in key mapping option(default) , it will be syndicated back.
Pls refer to these links for better understanding.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/uuid/80eb6ea5-2a2f-2b10-f68e-bf735a45705f
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/uuid/7051c376-f939-2b10-7da1-c4f8f9eecc8c%0c
Hope this helps,
+ An

Unplugging all network devices from Fios router prevents DVR freezing and remote control lock ups.

All,
I recently had a Verizon tech visit my house due to constant DVR and remote control freezing. TV content was freezing whether it was locally recorded, pulled from another DVR in the house, or On Demand. On a hunch after the tech tested everything and was about to leave, he unplugged my gigabit switch from the Fios router. Lo and behold everything started running perfectly. Since to the tech, the problem was solved, he closed the case and was on his way. The probem is of course I have more devices than the built in router switch provides ports for. My network is compised of an 8 port Netgear gigabit switch downstream from the Fios router with two wireless access points (with their own built in gigbait switches) connecting to the Netgear gigabit switch. There are no loops in the switch topology. I've tried changing out the router, the gigabit switch, removing the wireless acces points individually as well as plugging the access points directly into the Fios router switch (one at a time with no Netgear switch in the middle) and all scenarious cause the DVR/remote control freeezing to come back. The only devices I can plug into the Fios router without causing freezes are PC's....anything with it's own switch essentially brings the network to it's knees. If anyone has an idea how to get my network back in one piece AND make the DVR's/remotes behave, I'd greatly appreciate the help!
My Fios equipment:
MI-424WR GEN-3I rev I (eye) running firmware 40.19.36
5 Motorola HD-DVRs all QIP 7232-2 running software release 1.9.1 platform build 25.39 (Oct. 22, 2012)
Specific config:
75/35 Fios connecting via ethernet from ONT. Set-top boxes connect to Fios router coax port via powered splitter.
*All SNR/dB mesasurements taken by the tech from the set-top boxes and router are well within spec.
Fios router provides DHCP addressing. Wireless N access points are configured for roaming with the same SSID and non-overlapping channels. Access points are not providing routing or IP adressing...all layer 3 and up services still provided by Fios router
Diagram:
ONT
|
Fios Router ---------Cable Splitter---------Set Top Boxes
|
Netgear Switch
|           |
WAP1    WAP2

WayfarerII wrote:
... DVR ... remote ... freezing ... TV ... whether ... locally recorded, pulled from another DVR ...
... tech ... unplugged my gigabit switch from the Fios router ... and ... everything started running perfectly ...
... config:
75/35 Fios ... via ethernet from ONT ... Set-top boxes connect to Fios router via powered splitter ...
ONT
|
| cat5
|
Fios Router ---------Cable Splitter---------Set Top Boxes
|
Netgear Switch
|           |
WAP1    WAP2
I am inclined to echo several of the "tns" comments, particularly with respect to your splitter. My layout is based on a standard 8-port splitter of the type usually supplied in a VZ install. In addition I do have a ChannelPlus device that functions as a powered splitter, but its use is limited to distribution of secondary TV signals to older analog TVs. My first point then is that this may be an offender as "tns" has suggested.
In addition, I'd describe your wiring as "non-standard" (red-colored items in the above diagram)  As you're no doubt aware, with 75/35 you don't really need Cat5e from the ONT (your original diagram). It seems the highest tiers do require it, but in "standard" installations this run is coax directly to an 8-port non-powered splitter (below diagram), then from that splitter via coax to all STBs and CableCards, other TVs, et.), and also to the Actiontec.   Subsequent feeds from the Actiontec to wired devices (including WAPs) are via Ethernet (typically Cat 5e).
In fact I don't immediately see how your STBs get additional services such as On Demand and IMG with the wiring shown in your diagram (perhaps someone can help me out here). In "standard" installs the Actiontec must be connected via coax to the ONT to provide such services to other network clients. I don't see that requirement being met here.
For starters I'd recommend that you change your service from WAN Ethernet to WAN coax. This can easily be accomplished over the telephone. Then I'd run coax directly from the ONT to the Actiontec as in my revised diagram below (blue-colored items). If your setup can manage with this arrangement, I think it will help greatly with the "freezing" issue.
ONT - - - - - - coax - - - - -
                                         |
Fios Router --- coax--- Standard 8-Port Splitter --- coax --- Set Top Boxes
|cat5
Netgear Switch
|cat5          |cat5
WAP1 WAP2
Subsequent Note: You provided additional info while I was composing a response, and I'd like to offer another comment. Structured wiring "panels" of the type usually available are pre-configured to provide data, phone and video. This usually means that one is in certain respects limited by the ideas of the panel designer. I have what can be called a structured wiring layout, but it really is composed of individual small custom networks for each service (automation, security, video, data, telco, etc.), configured so that all wiring terminates in "home run" fashion at a central panel (a few details here: http://forums.verizon.com/t5/Home-Networking/Cmon-Show-Us-Your-Network/m-p/481733#M765 ). This layout makes it easier to make adjustments (and there have been quite a few over the intervening years). I'm thinking that in your case you may have to abandon the powered splitter (presumably) built into the panel in order to avoid your present fix.
Subsequent Subsequent Note:   From your description it seems that you are using more than a single "whole house" DVR to supply programming to other devices. This is a bit puzzling to me because somewhere along the line I recall reading that only a single whole house DVR was allowed on the network. Can you elaborate a bit?

Monitoring of remote system's Transactional RFC and Queued RFC

Hello,
In our production system, in rz20- CCMS monitor templates- Communication-Transactional RFC and Queued RFc- outbound queues- Queues otherwise not monitored we can see blocked queues for each client.
System is connected to solution manager and we wish the central auto reaction is implemented in solution manager
However i am unable to find Transactional RFC and Queued RFC for the remote system, they exist only for solution manager itself
Tell me how can i do the central monitoring

Hello,
First you need to check with your Landscape in solman in order to monitor any kind of activities to do so pls follow these steps.
Go to SMSY in solman under Landscape components>Product systemsselect you satellite system example SAP ECC.
On the main screen you will find client for which you have generated RFC connection. Please check though connection are working fine, Go to edit mode and try to click on generate button there will be a pop-up, which gives a clear picture of RFC connection which already exists, and you can also re-generate this RFC connection by clean it up when you re-generate pls select under Actions after generation assign RFC dest for system monitoring.
But make sure there is no project impact on this RFC, like they are not using any logical components and already have some projects running on this RFC connection.
I would advise you to first you the option of assign and check RFC button which is next to generate icon.
Regards
JUDE

Sunfire 280R and Remote System Control (RSC)

Similar Messages

Maybe you are looking for