Support for recovery

I am joy, i have hp G61, recently warn me system recovery or start windows normally(windows 7 home premium) i was recovery almost  2-3rd time but recovery message show again and again other hand windows was not start normally, what i do now?
When i run memory test thare show error 303 ( i think here harddisc have some problem) so please say something what i will do ? send me information my mail address [email protected]/[email protected] please

Hi
If possible, turn on power, press F10 to enter BIOS mode, and run Memory Test and Hard Drive Test if any test fails you need to replace the part. Please note you need to be sure which part has failed and replace that part only then the unit will work fine. As per my understanding error code 303 is Hard drive failure.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Similar Messages

  • Poor Support for Recovery Media Error.

    T'm trying to recovery a Sattelite laptop L675D (part no. PSK3JU-03L02D) for a friend. There was no recovery partion on the machine and it was out of warrenty, so I purchased the recovery media ($29.95). I started the process and it read the 3 CDs and then started the process of creating the partitions, but 45% into the "creating CRC files" it failed with error code  10-FA12-045D. 
    A call to Toshiba support told me to remove battery and AC for 15 minutes and try again.  Same result so another call to support.  They did not tell me what the code indicated, but checked that I could enter the recovery process via the hard drive without the CDs. They said they could get the machine running without sending new disks.  They charged $49,95 since the machine was out of warranty.  I asked that if they were unsuccessful at resolving the issue, would the charge be refunded and the support person said "yes".  We then attempted the recovery from the hard drive. (I thought this was useless since the media created the recovery partition and I would probably get the same error, but I went along...)
    After 30 minutes, I got the exact same error (10-FA12-045D) that I had got on previous recovery attempts at the same point in the process.  The new support person said that the message indicated missing drivers and they would need to send new media.  He checked with his supervisor and said the $49,95 was non-refundable.  NOT A VERY SATISFACTORY EXPERIENCE.
    I am now waiting for the next recovery media to arive.

    Hi
    If possible, turn on power, press F10 to enter BIOS mode, and run Memory Test and Hard Drive Test if any test fails you need to replace the part. Please note you need to be sure which part has failed and replace that part only then the unit will work fine. As per my understanding error code 303 is Hard drive failure.
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • HT4718 No 1.    I can not activate Filevault : FileVault can't be turned on for the disk "Macintosh HD". Some disk formats don't support the recovery partition required by encryption. To use encryption, reinstall this version of Mac OS X on a reformatted

    I have TWO PROBLEMS
    No 1.  I can not activate FileVault. It displyas as follows :
    FileVault can’t be turned on for the disk “Macintosh HD”.
    Some disk formats don’t support the recovery partition required by encryption. To use encryption, reinstall this version of Mac OS X on a reformatted disk.
    No 2. I can not activate Find My Mac service. It displays as follows :
    Find My Mac requires a recovery partition
    Some configurations, such as software or hardware RAID, do not support a recovery partition and can't be used with find my mac

    Restart holding down the option/alt key and see if you have a Recovery Volume.
    Recovery Partition – Recreate Without Reinstalling
    Recovery Partition – Recreate Without Reinstalling (Requires Installer)
    Recovery Drive – Restore Missing
    Recovery Disk Assistant

  • How do I get support for Windows 7 on, and a W7 backup disk for, my new ThinkPad?

    I know these have got to be stupid questions, since I am sure that they have to have been asked before (unless they are clearly explained somewhere that everyone else has found, and I am somehow completely missed it), but I did search the forums and was surprised NOT to find any info on getting Windows 7 technical support after it was factory installed in a month-old Thinkpad. I wonder if the apparent defects in my W7, or maybe a different problem in my browser, could be affecting my ability to search to forums?
    I believe that my Windows 7 is defective, but calling Lenovo, they just talked about reinstalling Win7 from the partition, which makes no sense, if my W7 copy is defective, wouldn't the copy in the partition be defective too? My mom said she ordered a $20 W7 backup disk with the PC, but I never received it, and now Lenovo tech tells me those aren't actually available, and she must have confused it with the W7 upgrade disk, which didn't sound right, since I thought the upgrade disk was over $100, and I never received that one either anyway. If the W7 that was factory-installed is defective, I am assuming it's a copy of the same one in the partition, so that partition recovery is not feasible, is there any way to reorder a W7 re-install disk that will still register as Genuine Windows 7 on a Thinkpad? Now when I search the Lenovo site, I cannot find ANY W7 disks of any kind, neither a backup for factory-installed W7, nor for upgrade from a prior Windows version. Does anyone know how I could go about re-ordering the W7 backup disk when it appears to be missing from the online catalog? Unless this too is a defect in my browser search: can someone give me the link to page where I could select and re-purchase a W7 backup disk?
    It has been a few years since I had a new PC, but I have never even heard of one before that did not come with instruction manuals and OS and support disks, and did not provide any tech support for its own factory-installed software or Windows, at least during the first few months of ownership. Where do new Thinkpad owners turn for individual W7 software support, since Microsoft swears it is Lenovo's responsibility to support W7 under its OEM license, yet Lenovo swears they only support hardware? It almost seems that new users are expected to know everything already, or be initiated enough with the product to know exactly what your problem is and what's causing it, in order to find an online fix. Who do you call if W7 or Lenovo software (but not an ISP issue) appear to be doing something to prevent online access, but there are no discernible hardware issues? Where do you call for individualized W7, as well as Lenovo software, support, especially after no one online has ever heard of your specific issues and has no workable ideas for fixing them, or when your problem prevents you from getting online at all?
    Thanks so much

    http://www.apple.com/support/bootcamp/
    Boot Camp Assistant is already on your computer. You just need to buy Windows. Read the instructions and help files very carefully. Back up your data before taking on this task.

  • Logical drive 1 status = Ready for recovery ml350 g5

    Hi,
    I have a problem with a HP Proliant ML350 G5, 2 weeks ago the server did shutdown unexpectedly i looked in the ACU and saw that the controller had a battery problem. I replaced the battery but the server keeps once or twice a day shutting down. I made a report from the ACU but i don't know what this all means.
    Here is a part of the report, i hope someone can lead me to the right solution,
    Thanks in advance.
    Array Diagnostic Utility Version 7.85.16.0
    Array Diagnostic Utility Inspection Report Version 7.85.16.0
    Date/Time:          Friday, June 27, 2014 3:43:11PM
    Computer Model:     HP Server
    SLOT SUMMARY:
       Slot Num  Slot Type  Array Controllers and Host Adapters Detected
       SLOT 0    PCI        Smart Array E200i Controller
    SLOT 0 Smart Array E200i Controller ERROR REPORT:
       Logical drive 1 status = Ready for recovery
    SUBSYSTEM INFORMATION:
       Chassis Serial Num:              GB87494LT1
       This Controller
          Array Serial Number:          QT79MU6382    
          Cache Serial Number:          P9A3A0B9SV00ST
       Other Controller
          Array Serial Number:          Not Available
          Cache Serial Number:          Not Available
    CONTROLLER IDENTIFICATION:
       Configured Logical Drives: 1
       Configuration Signature:   0xa00004c9
       Controller Firmware Rev:   1.66
       Controller ROM Revision:   1.66
       Controller Hardware Rev:   0x00
       Boot Block Version:        1.66
       Board ID:                  0x3211103c
       Cable or Config Error:     0x00 (No)
       Invalid Host RAM Address:  No
       CPU Revision:              0x00
       CPU to PCI ASIC Rev:       0x00
       Cache Controller ASIC Rev: 0x00
       PCI to Host ASIC Rev:      0x00
       Marketing Revision:        0x41 (Rev A)
       Expand Disable Code:       0x01
       Protocol Chip Count:       1
       Enclosure Count:           3
       Max SCSI IDs per Bus:      0
       Big Drive Map:             0x000c 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
       Big Ext Drive Map:         0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
       Big Non-Disk Drive Map:    0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
       Fibre Chip Count:          0
       Recovery ROM Inactive     
       Image Revision:               
       Recovery ROM Active Image 
       Flags Status:              0x10
       Battery PIC Rev:           0x20
       NCQ:                       Not Supported
    LOGICAL DRIVE IDENTIFICATION:
       Logical Drive 1:
          Sector Size:              512
          Sectors Available:        143305920
          Fault Tolerance Mode:     Mirroring
          Logical Param Table:      cyl=17562 heads=255 sec/track=32 xlate sig=0x0
          BIOS Disabled:            No
          Logical Drive Ident:      0x       0
          Logical Drive Label:      A00004C9QT79MU6382     678E
    LOGICAL DRIVE CONFIGURATION:
       Logical Drive 1:
          Configuration Signature:  0xa00004c9
          Mapping Scheme:           Multiple Block
          Physical Drives:          2 (number not valid after drive movement)
             This Logical Drive:    2 (excluding spare drives)
          Fault Tolerance Mode:     Mirroring
          Logical Param Table:      cyl=17562 heads=255 sec/track=32 xlate sig=0x0
          Distribution Factor:      256
          Operating System:         64768
          Controller Order:         0
          Additional Information:   0
          Offset to Data:           0
          Int 13h Support Enabled:  Yes
          Sectors on Volume:        143305920
          Sectors per Drive:        143305920
          Big Drive Assignment Map: 0x000c 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
          Big Spare Assignment Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
          Array Accelerator is enabled for this logical drive.
    LOGICAL DRIVE STATUS:
       Logical Drive 1:
          Drive Status:           Ready for recovery
          Blocks to Rebuild:      0
          Blocks Re-mapped:      
          Spare Status Flags:     0x00
          Spare to Replaced Map:  See Big Spare to Replace Map:
          Media Was Exchanged:    No
          Cache Failure:          No
          Expand Failure:         0x00
          Unit Flags:             0x00
          Big Remap Count:        All Counts Zero
          Big Drive Failure Map:     0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
          Big Replacement Drive Map: 0x0004 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
          Big Active Spare Map:      0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
          Big Spare to Replace Map:  No spares have replaced any drives
          Big Spare Marked OK Map:   0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
    MONITOR AND PERFORMANCE DATA:
       Port 1I, Box 1, Bay 2
          Factory:     Serial #, Firmware Rev, and Mfg/Model #:
             33 4e 50 32 34 36 59 30 30 30 30 30 39 38 31 36      3NP246Y000009816
             51 35 58 4e 48 50 44 37 00 00 00 00 48 50 20 20      Q5XNHPD7....HP 
             20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
             20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
             00 00 00 00                                          ....
          Since Power: Serial #, Firmware Rev, and Mfg/Model #:
             33 4e 50 32 34 36 59 30 30 30 30 30 39 38 31 36      3NP246Y000009816
             51 35 58 4e 48 50 44 37 00 00 00 00 48 50 20 20      Q5XNHPD7....HP 
             20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
             20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
             00 00 00 00                                          ....
          Serial Number Control:     0x0054
          Firmware Revision Control: 0x0248
          Mfg/Model Number Control:  0x0268
                     Factory          Since Power      Threshold        Control
          Serv. Time 00341415         000001d4         00000000         2104
          Read Blks  0000001788c34d46 00000000000002b1                  0108
          Hrd Read   00000485         00000000         00000000         2104
          Rtry Read  00000000         00000000         00000000         2104
          ECC Read   000000000000000d 0000000000000000 0000000000000000 2108
          Write Blks 00000006c04e371c 0000000000ffcf08                  0108
          Hrd Write  00000000         00000000         00000000         2104
          Rtry Write 00000006         00000000         00000000         2104
          Seeks      0000000000000000 0000000000000000                  0808
          Seek Errs  0000000000000000 0000000000000000 0000000000000000 0808
          Spin Cyls  00000000         00000000         00000000         2104
          Spin Time  0000             0000             0000             2202
          Test 1     0000             0000             0000             0802
          Test 2     0000             0000             0000             0802
          Test 3     0000             0000             0000             0802
          Test 4     0000             0000             0000             0802
          Spare Blks ffffffff         ffffffff                          0a04
          Re-mapped  0000009b         00000000         00000000         2504
          DRQ Tmots  0000             0000             0000             0802
          Timeouts   0000             0000             0000             2102
          Rebuilds   0002             0000             0000             2102
          Spn Retrs  ffff             ffff             0000             2902
          Fl Rd Recv 0000             0000             0000             2102
          Fl Wt Recv 0000             0000             0000             2102
          Format Err 0000             0000             0000             2102
          POST Err   0000             0000             0000             0802
          Drv Nt Ry  00000000         00000000         00000000         2104
          Reallc Abt 00000000         00000000         00000000         0804
          IRQ Gltchs 00000000         00000000         00000000         0804
          Bus Flts   00000054         00000001         00000000         2104
          Hot Plgs   00000000         00000000         00000000         2104
          Tk Rwt Err ffff             ffff             0000             2902
          Rmp Wt Err 0000             0000             0000             2102
          Bg Fw Rev  0000000000000000 0000000000000000                  0848
          Med Flrs   0000             0000             0000             2102
          Hrdw Errs  0007             0000             0000             2102
          Abt Cmd Fl 0000             0000             0000             2102
          Spn Up Fl  0000             0000             0000             2102
          Bd Tgt Cnt 0000             0000             0000             2102
          Pred Fails 00000000         00000000         00000000         2104
          DRIVE ERROR LOG:
             Error Log Header:
                Parameter Length    = 0x14
                Entry Size          = 0x0040
                Current Entry       = 0x1c
                Total Errors Logged = 0x0000021c
             Error Log Data:
    SCSI  CAM   Sense  Sense
    Stat  Stat  Key    Code    Qual   Block(Vl)       Time       Op   Info
    02    04    06     29      02     00000000(0)     002f200b   00   0000
    02    04    06     29      02     00000000(0)     002f477e   00   0000
    02    04    06     29      02     00000000(0)     0030a78b   00   0000
    02    04    06     29      02     00000000(0)     00311fd3   00   0000
    02    04    06     29      02     00000000(0)     00316ebf   00   0000
    00    0a    00     00      00     00000000(0)     00317117   00   0000
    02    04    06     29      02     00000000(0)     0032043a   00   0000
    02    04    06     29      02     00000000(0)     00329e1f   00   0000
    02    04    06     29      02     00000000(0)     0032c9aa   00   0000
    02    04    06     29      02     00000000(0)     0033b5c4   00   0000
    00    0a    00     00      00     00000000(0)     0033e304   00   0000
    00    0a    00     00      00     00000000(0)     0033e430   00   0000
    00    22    00     00      00     3f000000(0)     0033e509   5a   0000
    00    0a    00     00      00     00000000(0)     0033eec2   00   0000
    00    0a    00     00      00     00000000(0)     0033f285   00   0000
    00    0a    00     00      00     00000000(0)     0033f4f2   00   0000
    00    0a    00     00      00     00000000(0)     0033f6d2   00   0000
    00    0a    00     00      00     00000000(0)     0033fe90   00   0000
    00    0a    00     00      00     00000000(0)     0034003c   00   0000
    00    0a    00     00      00     00000000(0)     003402d0   00   0000
       Port 1I, Box 1, Bay 1
          Factory:     Serial #, Firmware Rev, and Mfg/Model #:
             33 4e 50 32 46 41 57 38 30 30 30 30 39 38 33 30      3NP2FAW800009830
             32 39 41 52 00 00 00 00 00 00 00 00 48 50 20 20      29AR........HP 
             20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
             20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
             00 00 00 00                                          ....
          Since Power: Serial #, Firmware Rev, and Mfg/Model #:
             33 4e 50 32 46 41 57 38 30 30 30 30 39 38 33 30      3NP2FAW800009830
             32 39 41 52 48 50 44 43 00 00 00 00 48 50 20 20      29ARHPDC....HP 
             20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
             20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
             00 00 00 00                                          ....
          Serial Number Control:     0x0054
          Firmware Revision Control: 0x0248
          Mfg/Model Number Control:  0x0268
                     Factory          Since Power      Threshold        Control
          Serv. Time 00055b43         000001d4         00000000         2104
          Read Blks  000000029c28733f 0000000001e70b56                  0108
          Hrd Read   00000000         00000000         00000000         2104
          Rtry Read  00000000         00000000         00000000         2104
          ECC Read   0000000000000000 0000000000000000 0000000000000000 2108
          Write Blks 00000000c7b62ee8 0000000000ffcf36                  0108
          Hrd Write  00000000         00000000         00000000         2104
          Rtry Write 00000000         00000000         00000000         2104
          Seeks      0000000000000000 0000000000000000                  0808
          Seek Errs  0000000000000000 0000000000000000 0000000000000000 0808
          Spin Cyls  00000000         00000000         00000000         2104
          Spin Time  0000             0000             0000             2202
          Test 1     0000             0000             0000             0802
          Test 2     0000             0000             0000             0802
          Test 3     0000             0000             0000             0802
          Test 4     0000             0000             0000             0802
          Spare Blks ffffffff         ffffffff                          0a04
          Re-mapped  00000000         00000000         00000000         2504
          DRQ Tmots  0000             0000             0000             0802
          Timeouts   0000             0000             0000             2102
          Rebuilds   0001             0000             0000             2102
          Spn Retrs  ffff             ffff             0000             2902
          Fl Rd Recv 0000             0000             0000             2102
          Fl Wt Recv 0000             0000             0000             2102
          Format Err 0000             0000             0000             2102
          POST Err   0000             0000             0000             0802
          Drv Nt Ry  00000000         00000000         00000000         2104
          Reallc Abt 00000000         00000000         00000000         0804
          IRQ Gltchs 00000000         00000000         00000000         0804
          Bus Flts   00000004         00000001         00000000         2104
          Hot Plgs   00000000         00000000         00000000         2104
          Tk Rwt Err ffff             ffff             0000             2902
          Rmp Wt Err 0000             0000             0000             2102
          Bg Fw Rev  0000000000000000 0000000000000000                  0848
          Med Flrs   0000             0000             0000             2102
          Hrdw Errs  0000             0000             0000             2102
          Abt Cmd Fl 0000             0000             0000             2102
          Spn Up Fl  0000             0000             0000             2102
          Bd Tgt Cnt 0000             0000             0000             2102
          Pred Fails 00000000         00000000         00000000         2104
          DRIVE ERROR LOG:
             Error Log Header:
                Parameter Length    = 0x14
                Entry Size          = 0x0040
                Current Entry       = 0x1f
                Total Errors Logged = 0x0000001f
             Error Log Data:
    SCSI  CAM   Sense  Sense
    Stat  Stat  Key    Code    Qual   Block(Vl)       Time       Op   Info
    02    04    06     29      02     00000000(0)     00000000   00   0000
    02    04    06     29      02     00000000(0)     00000001   00   0000
    02    04    06     29      02     00000000(0)     00006731   00   0000
    02    04    06     29      02     00000000(0)     00008ea4   00   0000
    02    04    06     29      02     00000000(0)     0001eeb1   00   0000
    02    04    06     29      02     00000000(0)     000266f9   00   0000
    02    04    06     29      02     00000000(0)     0002b5e5   00   0000
    02    04    06     29      02     00000000(0)     0002b83d   00   0000
    02    04    06     29      02     00000000(0)     00034b60   00   0000
    02    04    06     29      02     00000000(0)     0003e545   00   0000
    02    04    06     29      02     00000000(0)     000410d0   00   0000
    02    04    06     29      02     00000000(0)     0004fcea   00   0000
    02    04    06     29      02     00000000(0)     00052a2a   00   0000
    02    04    06     29      02     00000000(0)     00052b56   00   0000
    00    22    00     00      00     3f000000(0)     00052c2f   5a   0000
    02    04    06     29      02     00000000(0)     000535e8   00   0000
    02    04    06     29      02     00000000(0)     000539ab   00   0000
    02    04    06     29      02     00000000(0)     00053c18   00   0000
    02    04    06     29      02     00000000(0)     00053df8   00   0000
    02    04    06     29      02     00000000(0)     000545b6   00   0000

    Hi QUANT,
    Your Proliant server is a commercial product and to get your issue more exposure I would suggest posting in the commercial forums. Here is a link to the Commercial Notebook forum.
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • Some configurations such as a software or hardware RAID do not support a recovery partition and can't be used with Find My Mac.

    I'm getting the following error message when attempting to invoke "Find My Mac"
    Some configurations such as a software or hardware RAID do not support a recovery partition and can't be used with Find My Mac.

    You have no recovery partition. This is a normal condition if your boot volume is a software RAID, or if you modified the partition table after running Boot Camp Assistant to create a Windows partition. Otherwise, you need to reinstall OS X in order to add a recovery partition.
    If you don't have a current backup, you need to back up before you do anything else.
    You have several options for reinstalling.
    1. If you have access to a local, unencrypted Time Machine backup volume, and if that volume has a backup of a Mac (not necessarily this one) that was running the same major version of OS X and did have a Recovery partition, then you can boot from the Time Machine volume into Recovery by holding down the option key at the startup chime. Encrypted Time Machine volumes are not bootable, nor are network backups.
    2. If your Mac shipped with OS X 10.7 or later preinstalled, or if it's one of the computers that can be upgraded to use OS X Internet Recovery, you may be able to netboot from an Apple server by holding down the key combination option-R  at the startup chime. Release the keys when you see a spinning globe.
     Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication. 
    3. Use Recovery Disk Assistant (RDA) on another Mac running the same major version of OS X as yours to create a bootable USB device. Boot your Mac from the device by holding down the option key at startup.Warning: All existing data on the USB device will be erased when you use RDA.
    Once you've booted into Recovery, the OS X Utilities screen will appear. Follow the prompts to reinstall OS X. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
    If none of the above choices is open to you, then you'll have to start over from an OS X 10.6.8 installation. There's no need to overwrite your existing boot volume; you can use an external drive. Install 10.6 from the DVD you originally used to upgrade, or that came with the machine. Run Software Update and install all available updates. Log into the App Store with the Apple ID you used to buy 10.7 or later, and download the installer. When you run it, be sure to choose the right drive to install on.

  • SBS Exchange not available for recovery with Server Backup

    Hi
    I have a Small Business Server 2008 that we have taken over, and have found that the Exchange has not been backed up over the last 2 years, showing now a total of around 62000 log files,
    When running windows backup it gets to the screen showing
    "Running consistency check for application Exchange"
    This then fails, and the backup continues, but then tells me after that "Completed with Warnings"
    and under the errors in windows server backup it says "Application will not be available for recovery from this backup, Consistency check failed for components Microsoft Exchange Server"
    The following is what I have done to try resolve this issue, 
    Stopped SQL services then tried running the backup
    Stopped Information store and tried running backup
    Used Eseutil /D 
    Enabled Circular logging on the Exchange and tried the backup again,
    Please remember this database has not been backed up in 3 years, and there are log files from 2011, so loosing all the data is not an option,
    Regards
    Sergio Spinola

    Loosing the data is unlikely, and most of those logs will have been committed already.
    If you dismount the store, and run eseutil /mh "dbpath.edb" you can see which log files are required for the store to mount.
    Please review: http://support.microsoft.com/kb/2616952/en-us
    Robert Pearman SBS MVP
    itauthority.co.uk |
    Title(Required)
    Facebook |
    Twitter |
    Linked in |
    Google+

  • Help! Some features of Mac OS X Mavericks are not supported for the disk "Macintosh HD"

    I'm on a MacBook 13" mid 2010, OS X 10.7.5, I want to upgrade to OS X Mavericks. I have searched around for a few days, I find people with the same problem but can't really get the solution for it. I prefer not to reinstall OS X, I want to upgrade. I don't have boot camp or something just a 250 GB HD.
    Well, while I'm trying to upgrade from the download from Apps Store, I open the installer, press continue then accepts the Terms.. then select Macintosh HD and click install, then an warning message shows up "Some features of Mac OS X Mavericks are not supported for the disk "Macintosh HD"
    As I've read the article that is included in the waring message i did try to install anyway because it say that I would be fine, but when i did try to install the installer starts and after like 3 minutes a window appears, Install Failed.
    I've even try to make a installer on USB, both with the command in terminal and with Diskmaker, but it does not help.
    It seems impossible to upgrade. Please Help me.

    First, see the heading "What to do if the installer warns that no Recovery System can be created" in this support article. If you use Boot Camp, back up and delete the Windows partition using Boot Camp Assistant. Try the installation again.

  • DPM encountered an error while reading from the recovery point used for recovery.

    Hi Guys I'm getting this error:
    DPM encountered an error while reading from the recovery point used for recovery. Either the recovery point no longer exists or, if you
    selected a share for recovery, the path to its contents is missing from the recovery point.  (265)
    The DPM Server is on Windows 2012 DPM is 2012R2 4.2.1273.0
    The Server being backed up is 2012 R2 with DPM Agent 4.2.1273.0
    The Server has 3 Data Volumes (C: Drive) and D and E its the D and E drive that i get this error if i try and recover data from DPM.  the C Drive is fine.  the D and E Drive are different
    in that 1 De-dupe is enabled and 2 the Shadow Copies for these Volumes are stored on separate Disks F and G respectively.
    I've removed the Protection from drives D and E and reinstated it but every recovery point created
    brings up the same error message. I'm not sure where to go next do I need to Protect the Disks that have the Shadow copies on also? Many thanks in advance Gordon.

    Hi,
    It seems you are in a configuration where the Windows 2012 based DPM server does not understand how to read Windows 2012 R2 Dedup data structure which is what the DPM replica volume is.
    See the DPM supported and unsupported scenarios
    here under the deduplication issues section. 
    We have a fix in DPM2012 R2 UR5 that will protect the Windows 2012 R2 dedup volume in a non-dedup state on the DPM Server, but unfortunately that will not allow previous recovery points to be read.
    KB3021791-Description of Update Rollup 5 for System Center 2012 R2 Data Protection Manager
    Backup job for dedupe-enabled volume on Windows 2012 R2 fails. For example, Data Protection Manager backup might fail for following setup:
    Data Protection Manager2012 R2 is installed on Windows Server 2012.
    Data Protection Manager is protecting a dedupe-enabled volume on Windows Server 2012 R2.
    This also applied to restores as the above was for D2D2T backup that may fail as it needs to read the recovery point to back it up to tape.
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
    posting is provided "AS IS" with no warranties, and confers no rights.

  • USB/Flash support for Mountain Lion

    What App is availiable on app store as USB support for mountain lion? There was one 'USBmate'. Is it okay? If not please tell me how to get the USB support. I have downoaded installation of ML but have not installed it because backups have to be on external HDD. Please help me.

    I don't know to what you are referring. I think you mean a bootable USB flash drive for installing OS X. If so, then know there is no such thing for Mountain Lion. There was for Lion, but it is no longer available. Apple never included any installer disc for computers with Lion or Mountain Lion pre-installed.
    Reinstalling Lion or Mountain Lion is done through the Internet Recovery - OS X (Lion/Mountain Lion)- About OS X Recovery.
    If you download Lion or Mountain Lion from the App Store you can save the installer application and make a bootable installer from it:
    Make Your Own Mountain/Lion Installer
    1. After downloading Mountain/Lion you must first save the Install Mac OS X Mountain/Lion application. After Mountain/Lion downloads DO NOT click on the Install button. Go to your Applications folder and make a copy of the Mountain/Lion installer. Move the copy into your Downloads folder. Now you can click on the Install button. You must do this because the installer deletes itself automatically when it finishes installing.
    2. Get a USB flash drive that is at least 8 GBs. Prep this flash drive as follows:
    Open Disk Utility in your Utilities folder.
    After DU loads select your flash drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
    Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    Click on the Erase button. The format process can take up to an hour depending upon the flash drive size.
    3. Locate the saved Mountain/Lion installer in your Downloads folder. CTRL- or RIGHT-click on the installer and select Show Package Contents from the contextual menu. Double-click on the Contents folder to open it. Double-click on the SharedSupport folder. In this folder you will see a disc image named InstallESD.dmg.
    4. Plug in your freshly prepared USB flash drive. You are going to clone the content of the InstallESD.dmg disc image to the flash drive as follows:
    Double-click on the InstallESD.dmg file to mount it on your Desktop.
    Open Disk Utility.
    Select the USB flash drive from the left side list.
    Click on the Restore tab in the DU main window.
    Select the USB flash drive volume from the left side list and drag it to the Destination entry field.
    Drag the mounted disc icon from the Desktop into the Source entry field.
    Double-check you got it right, then click on the Restore button.
    When the clone is completed you have a fully bootable installer that you can use without having to re-download Mountain/Lion.
    Note: The term Mountain/Lion used above means Lion or Mountain Lion.
    As an alternative to the above you can try using Lion DiskMaker 2.0 that automates the process.

  • Request for recovery image and activation key

    Dear HP Support,
    I am Bhavanarayana from Hyderabad India. I have got a laptop HP G60 Notebook PC with pre installed os. My friend purchased this laptop from US and gifted to me. Recently my laptop got effected with virus and receovery partition also got effected which obstractiong when attempted for recovery. I have downloaded OS ( not original OEM ) from website and now facing the activation problem. As the devise purchased at US, Microsoft as well as HP support at India are helpless to activate the product.
    Kindly help.
    system Serial Number : [Moderator edited Serial Number]
    Thanks & Regards
    P Bhavanarayana
    E-Mail ID : [Moderator edited email address]

    I have just sent you a private message. If you are not sure how to check your forum messages, this post
    has instructions.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • Where to request support for unsupported (so far) VM argument (pmoffscreen)

    hi,
    i'm serving an app via web start, which has been great so far, but the app is very slow when viewed by a remote x-server. i found the VM argument pmoffscreen to be very useful for speeding up such response, but unfortunately i find that this VM argument is not supported for VMs started via web start. does anyone know why (buffer overflow issues or somesuch?), and where can i go to register desire for the support of this argument in web start VMs (if not here...)
    thanks!
    bruce

    Quote
    Hi Svet,
    i have bought a Samsung 830 SSD for my gx660r notebook, but i realized that it is not recognized in the BIOS in AHCI mode.
    The MSIHQ Flashing Tool says the following about my BIOS:
    Mainboard:  MS-16F1
    PCB Version:  To be filled by O.E.M.
    BIOS Version: E16F1IMS VER3.0J
    BIOS Date:  28.03.2011
    EC-FW Version:
    Could you provide me with a BIOS that works with my Samsung SSD?
    I already donated some bucks.
    Yep, check PM
    Quote
    And can you give me a hint how i can rescue my system in case the update fails?
    As far as i know, my notebook does not have m-flash (at least i've seen no reference to m-flash), is there another way to restore the backup bios in case something goes wrong?
    Nope, in a case of bad flash there is no recovery.
    Else if everything goes fine, you can restore original BIOS if you want to do this for some reason.
    Quote
    BTW: Im using the latest version of the flashing tool, but it does not offer the mode 2 (where i can point to a single bios file).
    To prevent using the wrong flasher[which can kill the notebook],
    Tool automatically Disable Mode2 when notebook is detected.
    Quote
    Can you provide the modded bios as a zip/rar file so i can use it with mode1?
    Yes, ofc. Check PM

  • [svn] 4078: Add support for dataTips to Slider

    Revision: 4078
    Author: [email protected]
    Date: 2008-11-11 17:41:52 -0800 (Tue, 11 Nov 2008)
    Log Message:
    Add support for dataTips to Slider
    SDK-16291 Implement data tip for slider
    - Added new dynamic, optional skin part called "dataTip".
    - Added dataTipFormatFunction, dataTipPrecision and showDataTip properties
    - Added protected function positionDataTip
    - Added dataTip skin part to FxHSliderSkin and FxVSliderSkin
    - data tip is an IDataRenderer, so it can render any type of data
    The data tip appearance is defined entirely by the skin. The position of the
    data tip is calculated using a combination of the skin and the Slider controller.
    The following properties were not retained from the Halo Slider:
    - sliderDataTipClass (the skin part allows the developer to define the data tip type)
    - dataTipStyleName (styling is defined on the skin part)
    - dataTipOffset (the offset position is defined in the skin part)
    SDK-16823 - Gumbo Slider does not support scroll wheel to increment / decrement value
    Slider listens for scroll wheel events anywhere on or off the stage while it has focus.
    QE Notes: Test new properties, functions and data tip behavior
    Doc Notes: Added new properties and functions
    Bugs: SDK-16291, SDK-16823
    Reviewer: Glenn and Gordon
    Ticket Links:
    http://bugs.adobe.com/jira/browse/SDK-16291
    http://bugs.adobe.com/jira/browse/SDK-16823
    http://bugs.adobe.com/jira/browse/SDK-16291
    http://bugs.adobe.com/jira/browse/SDK-16823
    Modified Paths:
    flex/sdk/trunk/frameworks/projects/flex4/src/mx/components/FxHSlider.as
    flex/sdk/trunk/frameworks/projects/flex4/src/mx/components/FxVSlider.as
    flex/sdk/trunk/frameworks/projects/flex4/src/mx/components/baseClasses/FxSlider.as
    flex/sdk/trunk/frameworks/projects/flex4/src/mx/components/baseClasses/FxTrackBase.as
    flex/sdk/trunk/frameworks/projects/flex4/src/mx/skins/spark/FxHSliderSkin.mxml
    flex/sdk/trunk/frameworks/projects/flex4/src/mx/skins/spark/FxVSliderSkin.mxml

    Kaffeegler
    Try rolling your fingertip on the mouse pad. This works very well and you have much more control.
    You've mentioned that you get fed up and then insert numbers or even click the up/down arrows.
    Alternatively and I only found this out the other day - thanks Victoria B.
    Use the comma , and period / stop . keys to navigate down / up through the settings below
    LR4 settings
    temp (white balance)
    tint
    exposure
    contrast
    highlights
    shadows
    white clipping
    black clipping
    clarity
    saturation
    vibrance
    LR3 settings
    temp (white balance)
    tint
    exposure
    contrast
    higlight recovery
    fill light
    black clipping
    brightness
    contrast
    and use the + and - keys  to move the sliders up and down in medium (±5)  steps and press control / cmd and + -  keys to use smaller (±1) steps. I think using the alt / option key with the + and - keys moves the sliders in larger (±10 oe 20) steps.
    You can use the aleft right rrow keys, but for some reason (bug), they dont follow the focus with the , and ., so you still need to click on the sliders to move the focus from one setting to another if you prefer to use the arrows.
    As I said above, the apple magic mouse is amazing for OSX snow leopard and Lion and is so intuitive for LR, but its an expensive mouse but IMHO well worth it
    Hope these help, the , and . is a great alternative to rolling your finger on the touchpad.
    hamish NIVEN Photography

  • I can not remember my icloud password.  I would like to recover it but the difficulty is my apple id and Icloud have differnt passwords and the links for recovery all work only to chnage my apple id password.

    I can not remember my icloud password.  I would like to recover it but the difficulty is my apple id and icloud have different passwords and the links for recovery all work only to change my apple id password.  SO how do I recover the icloud password?

    An Apple ID is used for everything (including this site) and including iCloud. See the quote below from https://appleid.apple.com/
    There is no such thing as an iCloud password but it is possible that you have 2 Apple IDs and you are using one of them for iCloud.
    An Apple ID is your user name for everything you do with Apple: Shop the iTunes Store, enable iCloud on all your devices, buy from the Apple Online Store, make a reservation at an Apple Retail Store, access the Apple Support website, and more.

  • Preparing for Recovery Loop

    I have an iPod Shuffle 3rd Gen. Whenever I connect it to my PC, open up iTunes, the status says that it's Preparing for Recovery but it only stays there. The iPod also doesn't show up in Windows Explorer.

    If you have not already, shut down (power off) your computer.  Use this procedure to reset iPod shuffle.
    http://support.apple.com/kb/HT1655
    Start up computer, with shuffle NOT connected.  Run iTunes.  Connect shuffle.
    If you were connecting the shuffle to a USB hub, try using a direct port on the computer.  You may also want to try disconnecting all other USB devices, except for standard mouse and keyboard, then connect shuffle.

Maybe you are looking for