Logical drive 1 status = Ready for recovery ml350 g5

Hi,
I have a problem with a HP Proliant ML350 G5, 2 weeks ago the server did shutdown unexpectedly i looked in the ACU and saw that the controller had a battery problem. I replaced the battery but the server keeps once or twice a day shutting down. I made a report from the ACU but i don't know what this all means.
Here is a part of the report, i hope someone can lead me to the right solution,
Thanks in advance.
Array Diagnostic Utility Version 7.85.16.0
Array Diagnostic Utility Inspection Report Version 7.85.16.0
Date/Time:          Friday, June 27, 2014 3:43:11PM
Computer Model:     HP Server
SLOT SUMMARY:
   Slot Num  Slot Type  Array Controllers and Host Adapters Detected
   SLOT 0    PCI        Smart Array E200i Controller
SLOT 0 Smart Array E200i Controller ERROR REPORT:
   Logical drive 1 status = Ready for recovery
SUBSYSTEM INFORMATION:
   Chassis Serial Num:              GB87494LT1
   This Controller
      Array Serial Number:          QT79MU6382    
      Cache Serial Number:          P9A3A0B9SV00ST
   Other Controller
      Array Serial Number:          Not Available
      Cache Serial Number:          Not Available
CONTROLLER IDENTIFICATION:
   Configured Logical Drives: 1
   Configuration Signature:   0xa00004c9
   Controller Firmware Rev:   1.66
   Controller ROM Revision:   1.66
   Controller Hardware Rev:   0x00
   Boot Block Version:        1.66
   Board ID:                  0x3211103c
   Cable or Config Error:     0x00 (No)
   Invalid Host RAM Address:  No
   CPU Revision:              0x00
   CPU to PCI ASIC Rev:       0x00
   Cache Controller ASIC Rev: 0x00
   PCI to Host ASIC Rev:      0x00
   Marketing Revision:        0x41 (Rev A)
   Expand Disable Code:       0x01
   Protocol Chip Count:       1
   Enclosure Count:           3
   Max SCSI IDs per Bus:      0
   Big Drive Map:             0x000c 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
   Big Ext Drive Map:         0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
   Big Non-Disk Drive Map:    0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
   Fibre Chip Count:          0
   Recovery ROM Inactive     
   Image Revision:               
   Recovery ROM Active Image 
   Flags Status:              0x10
   Battery PIC Rev:           0x20
   NCQ:                       Not Supported
LOGICAL DRIVE IDENTIFICATION:
   Logical Drive 1:
      Sector Size:              512
      Sectors Available:        143305920
      Fault Tolerance Mode:     Mirroring
      Logical Param Table:      cyl=17562 heads=255 sec/track=32 xlate sig=0x0
      BIOS Disabled:            No
      Logical Drive Ident:      0x       0
      Logical Drive Label:      A00004C9QT79MU6382     678E
LOGICAL DRIVE CONFIGURATION:
   Logical Drive 1:
      Configuration Signature:  0xa00004c9
      Mapping Scheme:           Multiple Block
      Physical Drives:          2 (number not valid after drive movement)
         This Logical Drive:    2 (excluding spare drives)
      Fault Tolerance Mode:     Mirroring
      Logical Param Table:      cyl=17562 heads=255 sec/track=32 xlate sig=0x0
      Distribution Factor:      256
      Operating System:         64768
      Controller Order:         0
      Additional Information:   0
      Offset to Data:           0
      Int 13h Support Enabled:  Yes
      Sectors on Volume:        143305920
      Sectors per Drive:        143305920
      Big Drive Assignment Map: 0x000c 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
      Big Spare Assignment Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
      Array Accelerator is enabled for this logical drive.
LOGICAL DRIVE STATUS:
   Logical Drive 1:
      Drive Status:           Ready for recovery
      Blocks to Rebuild:      0
      Blocks Re-mapped:      
      Spare Status Flags:     0x00
      Spare to Replaced Map:  See Big Spare to Replace Map:
      Media Was Exchanged:    No
      Cache Failure:          No
      Expand Failure:         0x00
      Unit Flags:             0x00
      Big Remap Count:        All Counts Zero
      Big Drive Failure Map:     0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
      Big Replacement Drive Map: 0x0004 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
      Big Active Spare Map:      0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
      Big Spare to Replace Map:  No spares have replaced any drives
      Big Spare Marked OK Map:   0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
MONITOR AND PERFORMANCE DATA:
   Port 1I, Box 1, Bay 2
      Factory:     Serial #, Firmware Rev, and Mfg/Model #:
         33 4e 50 32 34 36 59 30 30 30 30 30 39 38 31 36      3NP246Y000009816
         51 35 58 4e 48 50 44 37 00 00 00 00 48 50 20 20      Q5XNHPD7....HP 
         20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
         20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
         00 00 00 00                                          ....
      Since Power: Serial #, Firmware Rev, and Mfg/Model #:
         33 4e 50 32 34 36 59 30 30 30 30 30 39 38 31 36      3NP246Y000009816
         51 35 58 4e 48 50 44 37 00 00 00 00 48 50 20 20      Q5XNHPD7....HP 
         20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
         20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
         00 00 00 00                                          ....
      Serial Number Control:     0x0054
      Firmware Revision Control: 0x0248
      Mfg/Model Number Control:  0x0268
                 Factory          Since Power      Threshold        Control
      Serv. Time 00341415         000001d4         00000000         2104
      Read Blks  0000001788c34d46 00000000000002b1                  0108
      Hrd Read   00000485         00000000         00000000         2104
      Rtry Read  00000000         00000000         00000000         2104
      ECC Read   000000000000000d 0000000000000000 0000000000000000 2108
      Write Blks 00000006c04e371c 0000000000ffcf08                  0108
      Hrd Write  00000000         00000000         00000000         2104
      Rtry Write 00000006         00000000         00000000         2104
      Seeks      0000000000000000 0000000000000000                  0808
      Seek Errs  0000000000000000 0000000000000000 0000000000000000 0808
      Spin Cyls  00000000         00000000         00000000         2104
      Spin Time  0000             0000             0000             2202
      Test 1     0000             0000             0000             0802
      Test 2     0000             0000             0000             0802
      Test 3     0000             0000             0000             0802
      Test 4     0000             0000             0000             0802
      Spare Blks ffffffff         ffffffff                          0a04
      Re-mapped  0000009b         00000000         00000000         2504
      DRQ Tmots  0000             0000             0000             0802
      Timeouts   0000             0000             0000             2102
      Rebuilds   0002             0000             0000             2102
      Spn Retrs  ffff             ffff             0000             2902
      Fl Rd Recv 0000             0000             0000             2102
      Fl Wt Recv 0000             0000             0000             2102
      Format Err 0000             0000             0000             2102
      POST Err   0000             0000             0000             0802
      Drv Nt Ry  00000000         00000000         00000000         2104
      Reallc Abt 00000000         00000000         00000000         0804
      IRQ Gltchs 00000000         00000000         00000000         0804
      Bus Flts   00000054         00000001         00000000         2104
      Hot Plgs   00000000         00000000         00000000         2104
      Tk Rwt Err ffff             ffff             0000             2902
      Rmp Wt Err 0000             0000             0000             2102
      Bg Fw Rev  0000000000000000 0000000000000000                  0848
      Med Flrs   0000             0000             0000             2102
      Hrdw Errs  0007             0000             0000             2102
      Abt Cmd Fl 0000             0000             0000             2102
      Spn Up Fl  0000             0000             0000             2102
      Bd Tgt Cnt 0000             0000             0000             2102
      Pred Fails 00000000         00000000         00000000         2104
      DRIVE ERROR LOG:
         Error Log Header:
            Parameter Length    = 0x14
            Entry Size          = 0x0040
            Current Entry       = 0x1c
            Total Errors Logged = 0x0000021c
         Error Log Data:
SCSI  CAM   Sense  Sense
Stat  Stat  Key    Code    Qual   Block(Vl)       Time       Op   Info
02    04    06     29      02     00000000(0)     002f200b   00   0000
02    04    06     29      02     00000000(0)     002f477e   00   0000
02    04    06     29      02     00000000(0)     0030a78b   00   0000
02    04    06     29      02     00000000(0)     00311fd3   00   0000
02    04    06     29      02     00000000(0)     00316ebf   00   0000
00    0a    00     00      00     00000000(0)     00317117   00   0000
02    04    06     29      02     00000000(0)     0032043a   00   0000
02    04    06     29      02     00000000(0)     00329e1f   00   0000
02    04    06     29      02     00000000(0)     0032c9aa   00   0000
02    04    06     29      02     00000000(0)     0033b5c4   00   0000
00    0a    00     00      00     00000000(0)     0033e304   00   0000
00    0a    00     00      00     00000000(0)     0033e430   00   0000
00    22    00     00      00     3f000000(0)     0033e509   5a   0000
00    0a    00     00      00     00000000(0)     0033eec2   00   0000
00    0a    00     00      00     00000000(0)     0033f285   00   0000
00    0a    00     00      00     00000000(0)     0033f4f2   00   0000
00    0a    00     00      00     00000000(0)     0033f6d2   00   0000
00    0a    00     00      00     00000000(0)     0033fe90   00   0000
00    0a    00     00      00     00000000(0)     0034003c   00   0000
00    0a    00     00      00     00000000(0)     003402d0   00   0000
   Port 1I, Box 1, Bay 1
      Factory:     Serial #, Firmware Rev, and Mfg/Model #:
         33 4e 50 32 46 41 57 38 30 30 30 30 39 38 33 30      3NP2FAW800009830
         32 39 41 52 00 00 00 00 00 00 00 00 48 50 20 20      29AR........HP 
         20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
         20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
         00 00 00 00                                          ....
      Since Power: Serial #, Firmware Rev, and Mfg/Model #:
         33 4e 50 32 46 41 57 38 30 30 30 30 39 38 33 30      3NP2FAW800009830
         32 39 41 52 48 50 44 43 00 00 00 00 48 50 20 20      29ARHPDC....HP 
         20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20          DG072ABAB3 
         20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00          ............
         00 00 00 00                                          ....
      Serial Number Control:     0x0054
      Firmware Revision Control: 0x0248
      Mfg/Model Number Control:  0x0268
                 Factory          Since Power      Threshold        Control
      Serv. Time 00055b43         000001d4         00000000         2104
      Read Blks  000000029c28733f 0000000001e70b56                  0108
      Hrd Read   00000000         00000000         00000000         2104
      Rtry Read  00000000         00000000         00000000         2104
      ECC Read   0000000000000000 0000000000000000 0000000000000000 2108
      Write Blks 00000000c7b62ee8 0000000000ffcf36                  0108
      Hrd Write  00000000         00000000         00000000         2104
      Rtry Write 00000000         00000000         00000000         2104
      Seeks      0000000000000000 0000000000000000                  0808
      Seek Errs  0000000000000000 0000000000000000 0000000000000000 0808
      Spin Cyls  00000000         00000000         00000000         2104
      Spin Time  0000             0000             0000             2202
      Test 1     0000             0000             0000             0802
      Test 2     0000             0000             0000             0802
      Test 3     0000             0000             0000             0802
      Test 4     0000             0000             0000             0802
      Spare Blks ffffffff         ffffffff                          0a04
      Re-mapped  00000000         00000000         00000000         2504
      DRQ Tmots  0000             0000             0000             0802
      Timeouts   0000             0000             0000             2102
      Rebuilds   0001             0000             0000             2102
      Spn Retrs  ffff             ffff             0000             2902
      Fl Rd Recv 0000             0000             0000             2102
      Fl Wt Recv 0000             0000             0000             2102
      Format Err 0000             0000             0000             2102
      POST Err   0000             0000             0000             0802
      Drv Nt Ry  00000000         00000000         00000000         2104
      Reallc Abt 00000000         00000000         00000000         0804
      IRQ Gltchs 00000000         00000000         00000000         0804
      Bus Flts   00000004         00000001         00000000         2104
      Hot Plgs   00000000         00000000         00000000         2104
      Tk Rwt Err ffff             ffff             0000             2902
      Rmp Wt Err 0000             0000             0000             2102
      Bg Fw Rev  0000000000000000 0000000000000000                  0848
      Med Flrs   0000             0000             0000             2102
      Hrdw Errs  0000             0000             0000             2102
      Abt Cmd Fl 0000             0000             0000             2102
      Spn Up Fl  0000             0000             0000             2102
      Bd Tgt Cnt 0000             0000             0000             2102
      Pred Fails 00000000         00000000         00000000         2104
      DRIVE ERROR LOG:
         Error Log Header:
            Parameter Length    = 0x14
            Entry Size          = 0x0040
            Current Entry       = 0x1f
            Total Errors Logged = 0x0000001f
         Error Log Data:
SCSI  CAM   Sense  Sense
Stat  Stat  Key    Code    Qual   Block(Vl)       Time       Op   Info
02    04    06     29      02     00000000(0)     00000000   00   0000
02    04    06     29      02     00000000(0)     00000001   00   0000
02    04    06     29      02     00000000(0)     00006731   00   0000
02    04    06     29      02     00000000(0)     00008ea4   00   0000
02    04    06     29      02     00000000(0)     0001eeb1   00   0000
02    04    06     29      02     00000000(0)     000266f9   00   0000
02    04    06     29      02     00000000(0)     0002b5e5   00   0000
02    04    06     29      02     00000000(0)     0002b83d   00   0000
02    04    06     29      02     00000000(0)     00034b60   00   0000
02    04    06     29      02     00000000(0)     0003e545   00   0000
02    04    06     29      02     00000000(0)     000410d0   00   0000
02    04    06     29      02     00000000(0)     0004fcea   00   0000
02    04    06     29      02     00000000(0)     00052a2a   00   0000
02    04    06     29      02     00000000(0)     00052b56   00   0000
00    22    00     00      00     3f000000(0)     00052c2f   5a   0000
02    04    06     29      02     00000000(0)     000535e8   00   0000
02    04    06     29      02     00000000(0)     000539ab   00   0000
02    04    06     29      02     00000000(0)     00053c18   00   0000
02    04    06     29      02     00000000(0)     00053df8   00   0000
02    04    06     29      02     00000000(0)     000545b6   00   0000

Hi QUANT,
Your Proliant server is a commercial product and to get your issue more exposure I would suggest posting in the commercial forums. Here is a link to the Commercial Notebook forum.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Similar Messages

  • "This drive is not ready for use; it's door may be open ..."

    Hi.
    I recently updated to itunes 7, and then had an issue with a corrupt file on the i-pod (which resulted in chkdsk hanging itself at 27%, always). So I restored the i-pod and that took care of that - chkdsk now says it's fine.
    However - it is also empty. My machine and i-tunes recognize it fine upon start-up; however, a short while into a full synch to get my library back on the i-pod, I invariably get the following error message:
    "The drive is not ready for use; it's door may be open. Please check drive \Device\Harddisk\DR 3 and make sure that a disk is inserted and that the drive door is closed." The message comes with the options "cancel, ignore and continue", yet the latter two don't make a difference, and even if I choose cancel, itunes keeps trying until it eventually crashes.
    This always happens after itunes has synchronized about 1.13 GB (out of 18.55 available).
    As far as I can tell, both my system and the iPod are up to date (itunes and windows update say so, anyway). E: is unequivocally and exclusively allocated to the i-pod; changing the settings from "optimize for quick removal" to "optimize for performance" has made no discernible difference.
    Any ideas would be very much appreciated.
    Thanks.
    DELL Inspiron 4150   Windows XP  

    Hullo ...
    let me follow up on this again. I've followed your advice, de-installed spybot, no change. I looked through the windows support help base, nothing. While trying out different things, I started getting a "delayed write failed" message, and I did some things they suggested (including adjusting the registry - me, adjusting the registry!)and it went away, and now all I get is the "open door" message again.
    That is: everything works absolutely fine, I plug in the i-pod (latest version i-tunes and i-pod is up to date), it's recognized instantly by the explorer as well as i-tunes. I've run all scans you can possibly run on it, and it is fine (no corrupt files, nothing). I've restored it twice through i-tunes, twice through the explorer. I've changed the drive letter.
    It starts the synch fine (it's still almost empty after the last restore), but at some point, I get the error message. Interestingly enough, *up to* that point, it'll synch fine - I can disconnect it and play on it whatever's been synched thus far. I can also modify my i-tunes settings and preferences, all of which i-tunes will recognize and adhere to. It is just unwilling to put more than 1GB of stuff onto my 20GB i-pod.
    Something I've noticed is that it is sometimes indicating apparently faulty charges in the beginning (though that is quickly corrected once the synch starts), as in, it'll recognize a certain amount of audio files, but also claim a random amount of "other" files, which should not be there (apart from the 30MB or so of genuine i-pod software).
    Anyhow. I haven't seen any solutions to this on the forums or in the apple help files, but people appear to be having this problem still. Any ideas or input would be very much appreciated ...
    Thanks.

  • "The drive is not ready for use; its door may be open. Please check drive \

    3G IPOD problems which are driving me mad and i can see others have had the same problem but i can't find any solution written down.
    Basically my IPOD either freezes after a couple of songs or it downloads about 6Gb (of 40) and the freezes with the following message:
    "The drive is not ready for use; its door may be open. Please check drive \Device\Harddisk2\DR6 and make sure that a disk is inserted and that the drive door is closed"
    I've tried re-setting, installing etc but no luck. Any suggestions/solutions?
    Laptop - Packard Bell Notebook   Windows XP  

    Hmmmm. I'm not sure how to explain this.
    You need to change the Drive Letter for your iPod.
    You should be able to connect your iPod then open Windows Explorer and right click on your iPod(which seems to be Drive E:) and change it to a different letter (like H).
    If you haven't enabled disk use for your iPod it probably won't appear in Windows Explorer.
    To enable disk use: connect iPod, open iTunes. Open Preferences and select the iPod tab. Choose "enable disk use."
    Once you've done all that, try resyncing.

  • Hard Drive Crash and Desperate for Recovery Help

    Problem:  I have black and white JPEGS that need to be put back into color.
    We had a motor seize on a back up hard drive before getting the data backed up a second time.  I'm curious if there are any "backdoor" options for recovery.  Here is the scenario:
    3 months ago we finished editing a wedding and exported color and black & white photos for the client.  We moved the original RAW files off the laptop onto a back up external hard drive.   A few weeks later, that external hard drive, with ALL the original RAW images on it, crashed after our cat knocked it off our desk while the HD was running.  However, we have the final JPEGS saved on DVDs.  As fate would have it, the client came back later requesting several black and white photos to be given to them in color instead.
    After a thorough look from a computer expert it was concluded that the recovery would have to be done in a lab at a cost of $1800.  I gave a local shop our laptop to see if they could recover any "deleted" files and recapture the original RAW images.  Still looking through those but out of the RAW files that are there, most are unreadable or contain only part of the photos.  (Still haven't seen any of the clients photos we need anyway)
    Is there a way to get the eported black & white JPEGS back into color? 
    Maybe a backup file or saved catalogue combined with the JPEGS?
    Bottom line:  Is there a way to get around this problem at all without the original RAW images?

    3 months ago we finished editing a wedding and exported color and black & white photos for the client.  We moved the original RAW files off the laptop onto a back up external hard drive.
    Perhaps you are using the word backup to mean something different that I mean. To me, a backup means you have an original one on disk, and another copy on a different physical disk. It sounds as if you do not have this second copy. If you do, and I misunderstood, then please let me know.
    Is there a way to get the eported black & white JPEGS back into color?
    This is probably not possible. You could, if you were very good with photoshop, "colorize" thie images with a lot of effort, but there would be no way to guarantee that the colorized images are in any way close to the original color images, other than through tedious manual effort.
    Maybe a backup file or saved catalogue combined with the JPEGS?
    Saved catalogs do not contain the information about what was contained in the original RAW. If you have the Lightroom previews available as well, and these contain the color previews, there is a way to extract the previews, but depending on how you set your preferences, these may not be high-res previews.
    Is there a way to get around this problem at all without the original RAW images?
    I don't think there is an easy way to do it. Manual tedious colorizing of the photos, extracting previews, or paying $1800. I hope this prompts you to adopt a strategy of regularly backing up your photos and catalog file.

  • Order status:"ready for shipment"

    my credit card company called today to make sure i authorized a charge for a substantial amount, so i figured things must be happening. sure enough, i checked my order status online at the apple store and it has been changed to "ready for shipment".
    has anyone else's order status been changed, or iphones shipped?

    its more of an issue with how long it takes your bank to credit your account. The refund from apple will go through that day

  • Status ready for pickup but item is not in store??

    Pre-ordered Hardline Deluxe (PS4).  My order details says it's ready to be picked up in store (Montebello, CA - 1537).  I go to the store location and the sales rep says they haven't recieved any Deluxe Editions.  I was instructed to return later or Friday. (3 days from now). How does this happen with a pre-order?
    I called another location and they have received their allotment of Deluxe Editions (Glendora, CA).
    Should I cancel my current order and try another location?
    Is it possible to transfer the purchase to the Glendora, CA location and have them save a copy for me for pickup?
    Thanks for any help.

    Hello ZiGMoN,
    I’m not much of a gamer myself, but my younger brother sure is, and he is quite excited to get his hands on Battlefield Hardline Deluxe. It’s all he can talk about, so I know he’d be devastated if didn’t get his copy on release day.  There are times when circumstances outside of our control can cause unexpected delays though, and I’m sorry to hear this might have been the case for you.
    To see if I might be able to honor your request and modify your order for in-store pickup at our Glendora, CA store, I pulled up your account using the information attached to your forum profile. Thankfully, I see your concerns reached our phone customer care team, and they successfully changed the store location attached to your order. As such, I’m happy to report that our Glenda location has your order ready for pickup.  While we should be able to hold your order until March 25th, please feel free to visit the store at your earliest convenience.
    If you have any further questions or concerns for us, please don’t hesitate to let me know. I’ll be glad to help.
    Best wishes,
    Alex|Social Media Specialist | Best Buy® Corporate
     Private Message

  • Disk Partitioning / Logical Drives vs. One Key Recovery Functionality

    I just purchased a Windows 7 Lenovo H530 and need to know if I can shrink the C: drive and add an extended partition with logical volumes without disabling OKR / Rescue System 3.0 functionality. My 1 TB HDD:
    200 MB     SYSTEM_DRV (Primary Partition)
    906 GB     C: (Boot/System Primary Partition)
    25.07 GB  Unlabeled (OEM Partition)
    I've read loss of F2 functionality due to recovery partition ID changes and/or OKR fails to complete due to any change in the size of the original C: drive...also read post of successful OKR after altering the C: drive.
    Has anyone successfully attempted this on a newer machine? I can't find a definitive answer as the OKR software has been updated over time and most of the post are 2+ years old.  Thanks in advance for any assistance!

    Hi, You're lucky if you only have 2 partitions - isn't there a nice tiny one of 0,2 Gigabytes also?
    What I can tell you is that I spent a lot of time as well trying to mend the soft/partitioning and to get rid of bloatware!
    In short: I did a clean reinstall + recovered my OEM activation + partitioned the HDD as I wanted. Now it looks and reacts familiar (I used XP as well, before).
    BEWARE: trying partitions managers as Easeus or Paragon has blocked my partitions - they seem to be "coded" somehow.
    Do not hesitate: after you backup activation erase totally HDD (I used killdisc) and all shall be gone and you start fresh.
    Get a Win 7 serching for "digitalriver" Get ABW for activation restoring Get drivers from Lenovo support, install only what you need by function not all of them!
    Send a PM if you need more details. Regards from Romania!
    Enjoy!

  • Drive not ready for use

    when i go to update my ipod, i get this error: "the drive is not ready for use; it's door may be open. Please check drive\device\harddisk2\DR4 and make sure that a disk is inserted and that the driver door is closed." then it proceedes to freeze up itunes and then the computer. So when i get this, i have to format my ipod so that i will be able to put music on it again. then after 3 or 4 updates the same thing happens. but never right after i format it. anyone have this happen before or know why this would happen? it is an older ipod, with the click wheel. and it does have the most recent update.
      Windows XP  

    Try changing the drive letter for your iPod.
    If you don't know how to do it, I'll look around a bit and find an article to help
    ~iBook G4 1.07GHz (Kaiya), with extra 256MB RAM ~and a red Apple logo~(Mac OS X 10.3.9)~ LaCie 160GB external hard drive~ ~3G 15GB iPod (Nakai)~ ~GiveStarsto users who earn them.~

  • Drive not ready for use, door may be open

    iTunes transfers about 800mb of content before error message appears:
    The drive is not ready for use; its door may be open. Please check drive\...
    I have restored, formatted, tried different PC's always get same result. Visited genius bar and they declared that my iPod was healthy but refused to move enough content to the iPod to reproduce the problem. iPod is a little under 2 yrs old.
    My confidence and respect regarding Apple and it's products is now greatly in question. I spent $400 duchats on this thing and I am starting to feel like an unappreciated client.
    Thanks for any help...

    Hullo ...
    let me follow up on this again. I've followed your advice, de-installed spybot, no change. I looked through the windows support help base, nothing. While trying out different things, I started getting a "delayed write failed" message, and I did some things they suggested (including adjusting the registry - me, adjusting the registry!)and it went away, and now all I get is the "open door" message again.
    That is: everything works absolutely fine, I plug in the i-pod (latest version i-tunes and i-pod is up to date), it's recognized instantly by the explorer as well as i-tunes. I've run all scans you can possibly run on it, and it is fine (no corrupt files, nothing). I've restored it twice through i-tunes, twice through the explorer. I've changed the drive letter.
    It starts the synch fine (it's still almost empty after the last restore), but at some point, I get the error message. Interestingly enough, *up to* that point, it'll synch fine - I can disconnect it and play on it whatever's been synched thus far. I can also modify my i-tunes settings and preferences, all of which i-tunes will recognize and adhere to. It is just unwilling to put more than 1GB of stuff onto my 20GB i-pod.
    Something I've noticed is that it is sometimes indicating apparently faulty charges in the beginning (though that is quickly corrected once the synch starts), as in, it'll recognize a certain amount of audio files, but also claim a random amount of "other" files, which should not be there (apart from the 30MB or so of genuine i-pod software).
    Anyhow. I haven't seen any solutions to this on the forums or in the apple help files, but people appear to be having this problem still. Any ideas or input would be very much appreciated ...
    Thanks.

  • Apps no longer found on App Store - despite long been "Ready for Sale"

    As discovered yesterday, all our paid apps have been "lost" from the iOS App Store.
    An alert saying:
    "Your request could not be completed. The item you've requested is not currently available in the US store."
    ...appears instead.
    Nowhere are they to be found, either by navigating directly to their urls in a browser, or by searching via iTunes on computer, iPhone or iPad.
    Not even when clicking the link from within:
    [ my developers account > iTunes Connect > Manage your account > [particular app] > View in app store ]
    ...will they appear, despite them being marked as "Ready for Sale".
    This has been confirmed for the Swedish and US app stores so far, on different computers/locations.
    All these apps were approved between mid 2009 and mid 2010, and all have long had (and still have) the status "Ready for Sale" and are distributed worldwide.
    At the same time, only our FREE-apps are still to be found on the App Store.
    I've submitted a report to their support, but receiving a reply could take a while and in the meantime I'm loosing income.
    Does anybody know what's going on?
    Is this happening for others, or is it just our apps? Has this happened to others before?
    Thanks.

    Yes, apparently all of a sudden my previously active iOS-contract has been placed under "Request Contracts" instead of in "Contracts In Effect".
    When there's a change in contracts you'll always get a notification from Apple is my experience, but now nothing.
    My iAD and Free-contracts are still in effect, though.
    Could it be connection with having just paid the Mac OS X-developer fee? I strictly remember having ADDED this to my existing account, not creating a new one.
    So should I request a new contract, with all the hassle of having to send them the w8ben-form etc (taking forever)? Or is it a shorter process since I've been a registered developer for more than 2 years?
    Eh, I'll go ahead and click the "Request"-button for the iOS contract. If you have any more input I'll gladly hear it.

  • Error message: "the drive is not ready"

    Hi
    I have an 20 GB ipod that I bought a few years ago (the one with the dock connector) and a few weeks ago it started to give me problems.
    I can't transfer all my music from itunes to my ipod as the following message pops up after transfering about 2500 songs
    "the drive is not ready for use; its door may be open. Please check drive\device\hardisk\DR7and make sure that the disk is inserted and the drive door is closed"
    I have tried restoring the ipod and updating it with the 2005-10-12 updater. I have also updated itunes and checked both my c drive and the ipod harddrive for viruses, to no avail!!!!
    I don't really know what to do next so if anyone has had a similar problem and has any suggestions on how I might fix it then I would be very very grateful
    Thanks
    dell optiplex gx220   Windows 2000  

    argh i have the exact same problem...
    i bought my first ipod in june 04... may 05 i began getting connection and battery problems and so i sent it back... i recieved a new ipod of the same kind... black and white display, dock connector.. the four buttons at the top instead of on the wheel. now, four months after receiving my second ipod, i am getting more battery and connection problems, although they are not the same ones.
    last week i got the same message you got and after doing the same things you did i gave up when it still didnt work. i today tried again to update. instead of messages like i recieved before about drive doors being open (after it had transferred 1000 songs might i add) i got absolutely nothing from my pc or itunes (which was open and playing a pearl jam song) and my ipod turned itself off (even though it has full battery). i originally believed that the source of my problems is that my ipod was dropped by my 3 year old brother onto my tiled family room floor (at it froze often) but knowing that others have similar problems im not so sure..
    i have no idea how to fix this and i dont particularly wish to send my ipod back to apple and pay $250 for repairs, (for a second time), if that did result i would wait and buy myself an ipod photo for an extra few hundred dollars.
    anywho.. if anybody at all knows anything that could possibly work that i havent done (not including calling apple customer service, i tried that last time and the indian man at the other end of the line was absolutely no help.) your help would be greatly appreciated
    Thanks

  • Expense_status_code – Ready for Payment - Yet its already in Financials..!?

    To whom...
    An expense report that is 'Ready for Payment' is also in ORACLE Financials..?!?!?
    We have an issue with an expense report that has an expense_status_code of 'Ready for Payment' in the AP_EXPENSE_REPORT_HEADERS_all table.
    The thing is, it has already been imported into ORACLE Financials and exists in the ap_invoices_all tabgle and can be seen within Invoice Overview from Payables module.
    Under what curcumstances would/could this happen?
    What can I do with it in i-expenses?
    I'm not sure its related, but the 'Audit Reason' given is down as 'Unapplied Advance'.
    Thanks for looking..
    Steven

    The solution was due to an Administrator who put the IEXP in on the 27/1 BUT the date of the claim was 30/9 and because an Auditor runs the import from the 1/10 (as that's when IEXPS went live) so any ER's that are put in before that date will not be picked up until the Auditor does the AUTO APPROVAL Process at the end of every month. These are then validated and ready to pay the following month.
    So it seems, irrespective if they're in ORACLE Financials or not, if they're still as status 'Ready for Payment' they haven't yet been paid - although the Advance payment is probablies the reason why..
    Steven

  • Why logical partition is a must for voting disk and OCR

    Hi Guys,
    I just started handling jobs for RAC installation, I have a simple question regarding the setup.
    Why does logical partition have to be used for voting disk and OCR?
    I tried partition the disk that were provisioned for voting disk and OCR with primary partition but when OUI is trying to recognize the disk, it cannot find the disk that has been partitioned with primary partition.
    Thank you,
    Adhika

    Hello Adhika,
    I found it on this doc http://download.oracle.com/docs/cd/B28359_01/install.111/b28250/storage.htm
    Be aware of the following restrictions for partitions:
    * You cannot use primary partitions for storing Oracle Clusterware files while running the OUI to install Oracle Clusterware as described in Chapter 5, "Installing Oracle Clusterware". You must create logical drives inside extended partitions for the disks to be used by Oracle Clusterware files and Oracle ASM.
    * With 32-bit Windows, you cannot create more than four primary disk partitions for each disk. One of the primary partitions can be an extend partition, which can then be subdivided into multiple logical partitions.
    * You can assign mount points only to primary partitions and logical drives.
    * You must create logical drives inside extended partitions for the disks to be used by Oracle Clusterware files and Oracle ASM.
    * Oracle recommends that you limit the number of partitions you create on a single disk to prevent disk contention. Therefore, you may prefer to use extended partitions rather than primary partitions.
    For these reasons, you might prefer to use extended partitions for storing Oracle software files and not primary partitions.
    All the best,
    Rodrigo Mufalani
    http://www.mrdba.com.br/mufalani

  • First Blog - Ready for Approval

    I am not sure if this is the right forum for the below question.
    Few days back I submitted my first blog on SDN for approval. Later I updated it few times and re-posted it with status "Ready for Approval". Does anyone know if I need to inform SDN that I revised my earlier post or will SDN automatically pick up the latest version of my blog?
    Thanks.

    SDN will pick up the latest version of the "ready" blog, but depending on the blog and the area it can take several days.
    You might also get it back in "feedback" mode.
    After a while it should go faster, particularly if the blogs are reliably good.
    Cheers,
    Julius

  • Exit CL_HRASR00_POBJ_WF_EXIT triggered exeception for event STATE_CHG and (target) status READY- ERROR EVENT_RAISED - Error updating the process object

    Hi All
    I have set up a simple custom HCM process and Form regarding Infotype TO CREATE AND CHANGE POSITION. I have checked the process and form consistency and it seems fine. Now when I run the process from HRASR_DT it generates a process number but it also gives an error workflow could not start.I get following error (SWIA log - Step history)
    Executing flow work item - Transaction brackets of the workflow has been damaged
    Exception occurred - Error when starting work item 000000007031
    PROCESS_NODE - Error when processing node '0000000014' (ParForEach index 000000)
    CREATE - Error when creating a component of type 'Step'
    CREATE_WIM_HANDLE - Error when creating a work item
    CREATE_VIA_WFM - Exit CL_HRASR00_POBJ_WF_EXIT triggered exeception for event CREATED and (target) status
    EVENT_RAISED - Error updating the process object
    Executing flow work item - Exit CL_HRASR00_POBJ_WF_EXIT triggered exeception for event STATE_CHG and (target) status READY->ERROR
    EVENT_RAISED - Error updating the process object
    Executing flow work item - Transaction brackets of the workflow has been damaged
    Executing flow work item - Work item 000000007031: Object FLOWITEM method EXECUTE cannot be executed
    Executing flow work item - Error when processing node '0000000014' (ParForEach index 000000)
    Points to be noted:
    1) I have searched few SAP notes such as 1384961(Notes for 6.0.4) but our system is in higher level patch 6.0.5
    2) WF-BATCH have SAP_NEW and SAP_ALL authorization.
    Appreciate your valuable suggestions.
    Thanks
    Ragav

    Hi Ragav
    did you try to debug this? maybe something is missing in config of P&F?
    Since you are on 605, the following note would be there in your system....use it to debug:
    1422496 - Debugging background workflow tasks in HCM P&F
    This will help you find the root cause.
    regards,
    modak

Maybe you are looking for

  • Read excel cell when excel is already open

    Hello, I want to read a specific cell of a sheet with excel already open. Labview has only to read the cell and not have to open excel. I have several examples that show : Labvview open excel select excel file select workbook select sheet select cell

  • Synconizing Sound Files during Playback

    I'm trying to create a drumbox with multiple looped sound tracks. The user will have the ability to turn on and off sounds (e.g. hi-hat, snare drum, bass drum, etc). I've figured out how to start and stop sounds, loop them, and remove any unwanted de

  • IPHOTO EMAIL ATTACHMENT

    I am having difficulty attaching a photo to an email as a JPEG attachment. All the Iphoto email programs imbed the picture in the email message. I want to be able to attach an photo to an email such that our club newsletter editor can take the photo

  • Change Process in Provider Contracts

    We are trying to use the change process-Product Change in the  Provider Contracts. We have maintained the Up & Down selling by mentioning in COMMPR01 in the UP-Selling tab we have entered the different products B. C that needs to be shown for product

  • When I try to restore my iPod it says "itunes error 9006".

    I've done all updates for iTunes & IE8. I've checked security settings and everything. No matter what I do, I get error 9006 when I try to restore it. How do I fix this?