Switch configuration

Can i get any sample configuration for core , Distribution and Access layer switches with 7206 router using OSPF as a routing protocol .
Please give some 5 to 6 VLANs in core switches ( i need three tier config)

Hi Antony,
Check this link as it will guide you how to configure 3550 switch for ospf and other routing protocols which you can use as distrubution as well as core switch
http://www.cisco.com/en/US/products/hw/switches/ps646/products_configuration_guide_chapter09186a00801f0a42.html#1068572
HTH, if yes please rate the post.
Ankur

Similar Messages

"Server either does not have a virtual switch configured or none of the configured virtual switches have an IP address assigned" error driving me nuts!

OK; have been trying to setup a test VM based RDS deployment for a few days now with no luck.
this error mentioned above:
"Server <server name> either does not have a virtual switch configured or none of the configured virtual switches have an IP address assigned" error is driving me nuts!
I have removed and re-added the RD Virtualization Host role numerous times, each time having the "create a virtual switch" checkbox selected, but it did NOT create any virtual switch.
I created the external virtual switch manually and tried to create the desktop collection again, no luck with the same error.
a few questions:
1. you don't assign IP to a switch! you assign IP to Network Interfaces. why does the error puts it like this?! it is technically wrong.(yeah yeah I know all about how you'd assign IP to managed switches in real world to telnet into them and manage them.
you know better than me that it is not the case here!)
2.the RDS Virtualization hosts are using their wifi card as the card for the virtual switch. could that be the reason? I even disabled their unplugged wired NIC just to make sure that the wifi is the only available option for the RDS wizard to use for the
virtual switch creation; but it didn't use it and it didn't create any virtual switch automatically.
3.if WIFI nic is indeed the reason, is it your suspension or an official documents is there somewhere stating so (that the WIFI NICS on a Virtualization hosts are not supported as the hub for a virtual switch).
4.what are the properties of the virtual switch the RDS requires? does it have to be external? why can't it work even with my manually created external switch?
5.how would I fix it?
P.S: the environment is made up of 2 laptops, having windows 2012 R2 trial installed on them, using their wifi to connect to the out world. no cable is plugged into their wired NIC card.

Hi,
Thank you for posting in Windows Server Forum.
The simplest short term solution was to connect each computer to a small switch that had no other connectivity. This brought up the link light on the external NIC and allowed the creation of the collection to complete. You need to use an external switch. You
can create one external switch which might fix the problem.
Please check below article for information.
VDI Deployment Error About Virtual Switch
In addition please referthis article for information regarding virtual switch.
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support

Switch configuration for AP's

We are trying to install a 2106 controller with a few 1261 AP's which we have downgraded to Lightweight.
We are getting our head around the 2106 config but am unsure as to what config to put on the switchport the AP's connect to.
As far as our reading goes it is best practice to plug the AP's into a network swtich and trunk vlan's from the switch to the controller.
Bit confused about the way the AP's connect to the switch.
Thanks
Roger

Hi,
As I understood ... you need to map existing vlan subnet with your wlan ...
you will have interfaces which you first need to configure on your controller .
1) Management IP of wlc
2) AP- manager
3) dynamic interface which will be used to map the vlan with respective wlan
4) virtual
procedure :
1) if you do not have dhcp seperate configured , first you need to create vlan then configure svi interface with ip address and dhcp pool for your ap to get ip address in your l3 switch which is connected to your controller with default-router command which will point to your switch
2) login to your controller through console and configure the management IP address
command : WLC( config ) > interface address management ... ip address... mask .... gateway ( it will be your switch )
configure AP-manager interface with above command with ap manager option ..
Now switch side you configure the one port which is connected to your controller as a TRUNK
connect ap to any port which will configured with above vlan which you have configured in l3 switch
Now AP should get registered and then follow below procedure for getting client connected to respective WLAN
3 ) once you configure login to gui of controller and configure dynamic interface with existing vlan subnet and give the dhcp server ip address if you have or else configure the dhcp pool for users also.
4) go to " wireless " option
5) select the respective wlan and map the vlan with respective dynamic interface
check whether clients got ip address.
please let me know ........ if you have doubt about it

Switch configuration distributed environment

Hi
I have ISE 1.2 and catalyst 2960
Please I nedd a document of controller and switch configuration exemple in distributed environement (primary and secondary ISE MNT PSN)
Thanks

https://supportforums.cisco.com/docs/DOC-18325
http://www.cisco.com/en/US/docs/security/ise/1.0/user_guide/ise10_sw_cnfg.html
https://supportforums.cisco.com/docs/DOC-18121

IviSwitch looses value when sending, "configure switch" configuration = TRUE

Hi all,
we are currently evaluating Teststand 4.1 with a keithley 3706 system switch multimeter.
After a first enthusiasm, thinking this tool together with the switch multimeter fits perfect our needs, real life seems some harder.
Between several other problems, we need to tell the device, that the channel "s1com1" and "s1com2" are configuration channels.
Configuring the teststand step : Edit IVI Switch Step -> IVI switching, Configure Switch : Channels "s1com1", Configuration = True
leads to two actions observable in Ni Spy:
GetAttributeViBoolean(...,"s1com1", _IS_CONFIGURATION_CHANNEL , VI_FALSE)
SetAttributeViBoolean(...,"s1com1", _IS_CONFIGURATION_CHANNEL , VI_FALSE)
manually calling this class functions from an interactive CVI fp works as expected (setting it to VI_TRUE)
Does anybody have any hint what we could do wrong? Currently we are just before writing wrappers in cvi and skipping all the wonderful IVIStep Types in teststand.
Looking forward to any feedback
David Clus
Solved!
Go to Solution.

David -
This might the same problem that we recently discovered in our internal testing. For the problem that we found, we will likely include our fix in an upcoming maintenance release. Can you verify whether the problem still occurs if you change your regional settings to English in the control panel? If the problem no longer occurs, can you use this as a workaround for now?
Message Edited by Scott Richardson on 10-06-2008 10:48 AM
Scott Richardson
National Instruments

Redundant Switch Configuration

I'm trying to setup two Catalyst 3750X-48T-L switches to support redundant networking. Most pieces of equipment will have two Ethernet interfaces, each on separate subnets.
So far, I've got the switches configured as separate VLANs, connected together with stack cables as shown below. I can propagate Ethernet traffic in each subnet/VLAN independently. However, I cannot get packets routed across the VLANs/subnets.
I'm looking for guidance on what additional steps are needed. Do I need to define each port as a trunk connection?

If you want to route between the vlans then you need to have L3 vlan interfaces (SVIs) on the switches.
So for each vlan you need to create an SVI and assign it an IP address from the IP subnet used for that vlan.
Then you set the default gateway of the clients in that vlan to the be the SVI IP address.
Note - if your switches are stacked you only need to create the SVIs on the stack master.
Edit - haven't used 3750-X switches so you many also need to enable IP routing using the "ip routing" command.
Jon

Sf300 switch configuration

Hello , This is Shanker from India . can you tell me sf 300 switch configuration . how disable in traffic. .
my picture like i have ring network connect to my Gig port but i don't want to input 1 to 24 port .
so tell me how configuration

Hi Siva,
Now it would be good idea to upgrade boot code and firmware to the latest one:
firmware: 1.4.0.88
boot code: 1.3.5.06
to download:
http://software.cisco.com/download/release.html?mdfid=283019670&softwareid=282463181&release=1.4.0.88&relind=AVAILABLE&rellifecycle=&reltype=latest
for boot code upgrade:
http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=f1e39061efb14c94a570bcbd6582167b_Firmware_Upgrade_Troubleshooting_on_300_and_500_Series_Manag.xml&pid=4&fcid=&fpid=&slnid=6
Regards,
Aleksandra

Invalid switch configuration-oob error

Hi all,
We are using NAC in OOB Virtual Gateway mode only for wireless users.But we are facing an error on user PC stating that,
    invalid switch configuration-OOB error:OOB client MAC ADD/IP ADD not
                   found. Please contact your network administrator.
              Please contact your administrator if the problem persists.
Thanks in advance.

Please check your snmp settings on the wlc and the manager. This is usually seen when the agent passes the mac address and clients ip address to the CAS but the CAM never receives the mac notification trap.
thanks,
Tarik

How can I automate switch configuration

I am looking for a way to automate switch configurations. I want to create a standard configuration that I can apply to all new switches. What methods (software, scripts etc) are available to automate the configuration process? Ideally, the system would download and install a standard image and then apply a baseline config, which I could modify as needed after initial install.
Thanks

Sorry, this is correct URL - http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca735.html
Also search Cisco website for release notes for your specific product since there might be some differences in supported features (like auto save of configuration after auto-install finished etc.). Here is one of them:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5013/prod_bulletin0900aecd803fdc15.html
Regards,
iLya

Configuration Help 1130AG-VoIP-Vlans-Switch Configuration

1130AG running c1130-k9w7-tar.124-3g.JA1, in autonomous mode.
VoIP - Call manager 6x, Cisco phones only,
Vlans - Open, secure data using WPA2, VoIP Vlan is using pre shared keys.
Switch Configuration - C3548xl's, C356048ps, 6509 cores
I have been looking for configuration examples to help me configure the interfaces from the 3546xl and the C356048ps switched to the 1130AG.
Configuration between the C3548xl's, C356048ps, and 6509 cores on the trunk ports for QoS.
The call Manager is on Vlan 210 and the Vlan for the wireless voice is 202.
Any suggested links would be grate, I think I have found most of it but want to be sure.
Thanks

Just to expound upon the commands that were not working, I did use the /? switch to see available commands, so for example, the mls qos trust dscp command, I entered mls qos trust /? and the only option was cos.
I globally configured the switches with:
lldp run
no lldp tlv-select power-management
mls qos
network-policy profile 50
voice vlan 50 dscp 46
All of these commands worked fine. I was going to assign the network-policy 50 on each access port along with the commands of mls qos trust dscp, auto qos voip trust too, but did not get to that step.

Update Switch Configuration from Switch Executive 2.1 to 3.5

Hi everybody,
I tried to update from Switch Executive 2.1 to 3.5 and had to find out, that my configurations have stoppped working. To me, it looks like 3.5 doesn't like my IVI configuration for the switching modules.
The Verify function in MAX tells me that the PXI cards are not accessible. The frontpage of the switch configuration shows no configurations / terminal blocks.
Since the configuration consists of nine matrix cards with a lot of hardwires, I'd really appreciate a way to properly import the old configurations (xml files are available)
Any ideas?
Cheers
Oli
Programming languages don't create bad code, programmers create bad code....
Solved!
Go to Solution.

Hey Oli,
Background:
By default, NISE 3.5 and later use the DAQmx API (instead of IVI) to directly control switch modules. This is different from previous versions, which required setting up an IVI session for each NI Switch module. You can still use IVI with NI Switch modules in NISE 3.5 and later, but this is not the default behavior.
The KB Sebastian referenced lists three different upgrade paths to use exported IVI Virtual devices in NISE 3.5 and later. As you've discovered, NISE 2.1 has fewer export formats, so we'll need to take the following steps:
Assumptions:
You have virtual devices created in NISE 2.1 (file format doesn't matter).
IVI Sessions and Logical names haven't been setup on your NISE 3.5 machine:
Action items:
Create IVI sessions and logical names. You could manually create the IVI sessions (as mentioned in the KB), but there's a MUCH easier method:
Right click on the NISE Virtual Devices tab and select 'Create New':
Click the 'auto create IVI devices' button. A dialogue will pop up... just click yes:
The NISE Create Virtual device window should now look like this:
Notice that we now have IVI devices. Sweet! So now just click cancel (yes, cancel)... we only used this dummy virtual device to simplify the IVI creation process.
If you look in MAX, it'll appear as if there still aren't any IVI devices:
Fear not, all we need to do is refresh. To do this, hit F5, and voila!:
So now all you need to do is change the IVI Logical name to whatever your old IVI Logical name was and then import as normal.
At this point, you should be operational using IVI devices in NISE 3.5 (if not, post up). If you'd like to go one step further and upgrade to purely DAQmx calls, just follow the steps in the 'Upgrading from IVI to NI-DAQmx' section. Note that once you've upgraded to DAQmx, you'll only be able to use exported Virtual devices with NISE 3.5 and later.
Have a great day!
-John Sullivan
Analog Engineer

Switch configuration urgent help (edge and core)

hi
i have new project in with the bellow product :
20 X WS-C2960-24TC-S
2 X WS-C3750X-48T-S
2 X WS-C2960S-24TS-S
i need to configure this switch in order to work without having vlan, first the 2 core switch for redundancy, then each catalyst switch 2960(edge Switch) connected to the two core with 2 uplink each uplink will be connected to single core switch(i have 2 core switch and i want to configure it in stack mode redundancy)
i need help to configure this switch to work perfectly with each other in best redundancy mode any configuration for this switch will be very helpfull for me
thank you

Hey,
This is a very open question but i believe the document below is a good point to start:
http://www.cisco.com/c/dam/en/us/td/docs/solutions/Enterprise/Small_Enterprise_Design_Profile/chap2sba.pdf
HTH.
Regards,
RS.

WAE-7326-K9 Content Services Switch Configuration

Hello -
Our ITC purchased a new Cisco 7326 Wide Area Application Engine equipped with three 300GB hard drives and ACNS version 5.5. We intend to utilize this applicance as a cache engine only.
The 7326 will connect to our Cisco 7206 BGP Router and Cisco 6513. The BGP is connected to an 80Mbit/s Internet source and the other is 10Mbit/s.
Anyone installed a 7326 cache engine? Any configuration examples or help is appreciated.
We are replacing a StrataCache 3 server cache engine with an F5 switch.
Thank You.

Dim sReturn
sReturn = Request.Cookies("MSCSFirstRequestedURL") & "guid=" & sGUID
Response.Redirect sReturn

Appropriate procedure to export and import switch configurations??

We have several SFP-300 series PoE switches already configured and in production usage.
What is the appropriate procedure to export the configuration from one of these switches, then import into a newly-purchased switch of the same model??
The only thing that needs to be different asap is the switch's IP address...can I modify this within the exported configuration file to be imported??
Or is there some other way I should go about this process??
Thank you, Tom

The configuration is just a text file. It's contents is basically just a list of configuration commands. You can download a backup from one of the switches that are already in use and modify it in a text editor. Then, you should be able to upload it to the new switch. That probably just works without adjustments, if the new switch has the same interface type and count.

Basic switch configuration

hi
I need help about Cisco switch 2960 issue how i give IP address gateway in switch if there more than two vlan and how configure telnet command
plz help me

Hi,
Do you have Lan Lite or Lan Base license (check with "show version")? LAN LITE does not permit routing.
With LAN BASE:
sdm prefer lanbase-routing // save before your config, you may loose some configuration
reload the switch
Example for gateway configuration:
vlan 10
vlan 20
interface vlan 10
ip address 10.0.10.1 255.255.255.0
interface vlan 20
ip address 10.0.20.1 255.255.255.0
For telnet:
username name privilege 15 secret password
line vty 0 15
login local
transport input all
But, do not use telnet (all traffic passes on clear including passwords), use instead ssh if the switch permits:
hostname switch
ip domain name company.com
crypto key generate rsa general-keys modulus 2028
line vty 0 15
login local
transport input ssh
Hope this could help you!
Regards,
Pedro Lereno

Switch configuration

Similar Messages

Maybe you are looking for