System halt after installation

Hi,
i installed Solaris 8 2/02 on an SunFire120. After the installation with the "installation cd" the system rebooted and started the "Web Start Launcher in Command Line Mode". After that he wants to install "Additional Software". The status bar is up to 100% at the beginning and then it seems, that the system halted. You cannot execute any commands oder start a cd. You are not in de OS (no prompt).
Does anybody have a solution?

Two suggestion you might try:
1. Update your video monitor to the latest version.
2. Put a small delay (around 10 to 100 ms) in all your For and While Loops (including sub VIs). To create a delay, use the the 'Wait' sub VI in the Time & Dialog sub palette. This will force LabVIEW to pause momentarily and let Windows do other stuff....
Chris_Mitchell
Product Development Engineer
Certified LabVIEW Architect

Similar Messages

System freezes after installation of version 11.5.502.149

WindowsXp, Firefox, Flash player 11.5.502.149 - I have made 2 attempts to load latest version; both times when I have restarted my system Windows will only load to Wallpaper and then stops- I waited for atleast 30 minutes - no program icons, no taskbar etc, Have used safe mode to uninstall flash player, did registry fix, have used system restore, still will not load. Did chkdsk - no apparent disk problems - but then after attempting to restart several times after long wait finally loaded. System will now restart, but as this happened after installation of flash player 2x I am unwilling to retry. - and now can not reload older version of flashplayer. - have recently installed other program updates and have not had system freeze so do not think it is a general installation problem. Any ideas?
Thanks

Pat
Trying to install an older version I got a message something to the effect that a newer version is available and program does not install. By hunting around the support areas on Adobe I did find a page that noted that if for some reason the new version did not work an older version was archived and a link.. so I did find an older version that would load.. of course I had to find a Zip program to unzip the file and it did try the same message ... there were 2 unzipped versions - only one worked but I do now have a working version albeit of Flash Player.
I googled for WindowsXp freezing and found a number of bulletin boards/forums that discussed solutions - which were pretty much what I did. Typically it happened after installing a new or updated program. No reasons were mentioned as to why or what was happening and the solutions of starting in safe mode, uninstalling, restoring, chkdsk are all sort of hit and miss... if one doesn't work try another... with the final solution being reload windows.. of course my version came installed and I don't have a backup disk so I imagine that would be another day or two of total frustration... so I guess I will avoid trying to update the flash player as long as possible. I have my system set up to only allow updates I have confirmed.
Thanks for your prompt response.
Janet Forbes
Quoting Pat Willener <[email protected]>:
Pat Willener http://forums.adobe.com/people/pwillener created the
discussion
"Re: system freezes after installation of version 11.5.502.149"
To view the discussion, visit:
http://forums.adobe.com/message/5057581#5057581

System halt after my program run

infoI make a program by LabVIEW 6i. The program function is that firstly it get data from OPC server by network, secondly to send command by RS-232. But the program do not run correctly. some information as follows:
1. computer: advantech industrial PC, CPU: P3-800(intel), memory:128M, HD:20G, display memory:4M(ATI), net crad: 3Com(3c905,10-100M)
2. system: windows NT4.0 workstation with SP4 (chinese), LabVIEW 6i
3. OPC: server: citect.opc (citect is automation & industrial software),
client: labVIEW.opc
4. some phenomena: when the program run after 4-5 hours or 10-12 hours, system halt and show that visual memory is shortage(visual memory of system is 160M).
I do not know why it is, need you help.
thanks
in advance.
Liu Weixing
2001/10/23
Attachments:
Opc.exe ‏608 KB

Two suggestion you might try:
1. Update your video monitor to the latest version.
2. Put a small delay (around 10 to 100 ms) in all your For and While Loops (including sub VIs). To create a delay, use the the 'Wait' sub VI in the Time & Dialog sub palette. This will force LabVIEW to pause momentarily and let Windows do other stuff....
Chris_Mitchell
Product Development Engineer
Certified LabVIEW Architect

System Halts after DVD-Au

As long as I'm reading these forums, I mise wll post another problem I am having.
When using my SB Audigy 2 ZS to DVD Audio, I use the Creative DVD-Audio Player, which I think is pretty much required. The sound is amazing..etc... However, when I close the dvd-audio player I get a system error (one of those prompts with sending information to microsoft) and then the system halts...screen goes blank and I have to reset the computer.
I havn't seen anything about this in the FAQ. I've re-installed the drivers before for other reasons and nothing seems to fix this.
Any ideas on this, or is it a known bug/hardware conflict with certain computers? I have an AMD Athlon XP, via chipset..on board sound but disabled the driver. No conflicts given from system. I am using the analog 5. outputs. The dvd-rom is a generic brand, but I suspect that should not matter. I do not have issues playing DVD movies and the audio works fine for the audio. It is simply the program...
Thanks fo rany help.
-Andy

Checking again for anybody who might know the issue?

App doesn't show up in System Preferences after Installation

Hi -
I've been trying to install a Wireless-G USB Adapter on a G3
and is is supposed to show up in the System Preferences,
but after the installation is complete, it's not there.
Can anyone help???
Thanks...

The guide that came with the adapter says it's for OSX - OS10.3, and I'm running 10.2 - The adapter is a Hawking HWL2A for Apple users, and I was told it would work on my G3.
I understand that my USB is only 1.1, but does that affect the installer?
Would you recommend me to just obtain the original airport card & adapter?
Thanks for your help...

Significant system slowdown after installation of 10.5.4

I downloaded update 10.5.4 this afternoon (about 3:30PM MDT Jun 30). Thereafter I noted a significant system slowdown. Symptoms: much slower system boot.
Safari, instead of the usual 2 "bounces" to start, took 8. I rebooted twice to confirm. (Now, even Firefox3 is faster!)
I am a relative newbie to the MacOSX world (10-year Windows veteran) so I haven't the slightest hint how to investigate... A simple-minded hint, for the likes of me, would be much appreciated! I'll check back in tomorrow morning.

Hi fjpoblam-
I have some possible causes for you, and a couple solutions to suggest...
CAUSES?
(Keeping in mind that some of these may be unlikely, they are all possible and shouldn't be automatically discounted because of their odds.)
1. The 10.5.4 update may have been corrupted or done something wrong.
2. A previous OS X update may have somehow been corrupted or done something wrong that was then made worse by the 10.5.4 update.
3. You may have some third-party software that isn't playing nice with 10.5.4.
4. Your unit could have a hardware issue which may have been triggered by the 10.5.4 update, or that just happened to appear at the same time by coincidence.
TROUBLESHOOT:
(letting me know the results of these tests might help narrow down the problem)
I. Unplug all external devices (USB, Firewire, ExpressCard, Ethernet, Monitor) and turn off Airport. Restart and see if the problem is gone.
II. From the Login screen, hold down shift immediately after pressing Login, which will prevent any Login Items from starting. Play around a bit and see if the problem is gone.
III. Startup holding down the Shift key, which will boot into "Safe Mode", temporarily disabling third-party and unnecessary extensions. Check to see if the problem is gone.
IV. Does it occur just on AC power, just on battery power, or both? Is there anything about the hardware that did not originally come with it from Apple? Do you have any third-party RAM installed?
_(Possible) SOLUTIONS_:
a) Download and run the 10.5.4 "Combo Updater" from http://www.apple.com/support/downloads/macosx1054comboupdate.html. It should still run even though you are already at 10.5.4. This will often have the ability to fix problems that were created by previous OS X updates and/or conflicts between updates as a result of corruption or errors. *(Likelihood to fix: 30%)* +Note: I always prefer to do OS X updates via combo updaters rather than the automatic Software Updates just to be safe, even though it works fine for most people.+
b) Do an "Archive and Install" via your original Leopard disc _(Backup everything first!!)_. This is one of the most time consuming and least enjoyable options, but almost always works. Startup from the Leopard disc and run the installer; when you see an "Options" button, click it and select "Archive and Install" and check the boxes to Preserve Users and Applications. Make sure you do not skip that option because if you continue with the install without making that selection you will loose your data. *(Likelihood to fix: 90%)*
c) Take the unit to an Apple retail store or call Technical support. My guess is that their recommendation will be to do an Archive and Install, but if that doesn't work and it turns out to be a hardware issue they will be your only options for repair or replacement. If you go to a retail store, you can make an appointment ahead of time through this site: http://www.apple.com/retail/storelist/ by selecting a store and clicking "Reserve" under Genius Bar so that you don't have to wait in line. *(Likelihood to fix: 100%)*
+REMINDER TO EVERYONE: Although hardware and software perform without problems most of the time for most people, things can go wrong for no good reason to anyone at anytime with any OS (sadly, some people get hit more often than others). ALWAYS make a backup of your data before doing major updates (especially OS updates). I know it doesn't help to hear after the fact, and backing up isn't convenient for many people, but it's guaranteed to prevent this problem every time. I at least suggest holding off from immediately doing updates and letting others be the guinea pigs instead.+

[SOLVED] No operating system found after installation

Hey there,
I'm new to Arch, I switched from Ubuntu and I'm willing to give Arch a fair try. My system is now more or less up and running and I'm very excited.
However, I can only boot with the CD inserted and by choosing "Boot existing OS". If I remove the CD, I cannot boot because no OS is found on the harddisk.
I tried running "grub-install /dev/sda" again, but that didn't work.
I installed using "gdisk". My main system partition is encrypted, but /boot is not encrypted. I used a simple partition layout with LUKS, no LVM. I tried to find my error on the Installation Guide and the Beginners Guide, but I can't figure out what I did wrong...
Help would be much appreciated. Let me know if you use further information.
Thanks in advance
Jonas
Last edited by freijon (2014-04-06 14:04:36)

Oxyd wrote:
For UEFI, you need an EFI System Partition. You don't need the BIOS boot partition.
Oh, and the installation CD needs to have been booted in UEFI mode as well. UEFI systems generally support both UEFI booting and legacy BIOS emulation. If you boot in BIOS mode, GRUB won't be able to install properly. You can run your whole setup in BIOS emulation mode if you don't particularly care for UEFI, but then using a legacy MSDOS partition table would perhaps be preferrable over GPT. (Or so the Wiki says.)
As for "booting in UEFI mode" -- when I start my system up, I can press F11 to bring up a selection of where to boot from. Your key is likely going to vary, but the important bit is that -- on my computer at least -- it shows me two very similar entries for the Arch CD -- except one has "UEFI: " prepended to it -- that's the one I use to boot in UEFI mode. Your mileage is going to vary, but hopefully it'll be somewhat similar.
I found an option in my BIOS to enable UEFI, but it is disabled by default. I find it quite strange that I have to enable this in order to make my installation work, as I never did this with Ubuntu. If I enable the third option (see pic), then I can boot the CD in UEFI mode. So that works. My question now is: Can I fix my installation or do I have to reinstall the entire system? I read in the wiki that the UEFI system partition has to be FAT32 and there is a minimal size of 256MB. However, my current boot partition is only 200MB. So I cant just reformat my old boot partition, or am I wrong?
http://i.imgur.com/LS6x1VBl.jpg
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code [jwr] --

Error while connecting to workflow builder after installation...first time!

Hi,
I have installed Oracle Workflow Builder 2.6.3 recently on my system and after installation, when I am trying to connect the workflow builder (using database username/password of that particular instance), it is throwing me the following error:
220: Unable to set NLS_LANGUAGE.
210: Oracle Error: ORA-01403: no data found
. SQL text: SELECT NLS_LANGUAGE FROM WF_LANGUAGES WHERE :l IN (NLS_LANGUAGE, CODE)
In the previous threads when I searched for the same issue, I found that if
select value from v$nls_parameters
where parameter='NLS_CHARACTERSET';
returns the value other then WE8ISO8859P1 then that is what I should change my NLS_LANG entry for the builder - i.e. AMERICAN_AMERICA.<character set>.
But I am not getting where should I change NLS_LANG, it is located where...some file? I am new to Workflow.
Please help me. I tried a lot. Any type of help will be highly appreciated.
Thanks,
Sumir

This issue (and solution) is described in ML Doc 577905.1 (Error While Connecting To Database Via Workflow Builder)
HTH
Srini

Acarbat Freezed after installation and run it for Mac Pro!

Dear all,
I tried to install Acrobat 9 Pro to one station this morning (or install
Adobe Reader 9 couple days ago), but the system hanged after installation
and ran it. Clicking "force quit", it showed that "Acrobat (no response)".
Following are the general description about the workstation and it is
connected to Mac server.
Workstation which tried to install Acrobat 9 Pro:
- Mac Pro Processor: 2* 3GHz Dual-core Intel Xeon
- Memory: 4GHz
- Mac OS X 10.5.6
Server
- Mac Pro Processor: Dual 2 GHz Power PC G5
- Memory: 3GHz
- Mac OS X Server 10.5.6
- Service: AFP, FTP, Open Directory (control the use login for all
workstations)
Installation procedures:
- Login the workstation as an Administrator (local)
- Install Acrobat 9 PRO
- Registration
- Shut down the workstation after installation
- Restart the workstation
- Use my unique name to login (all my files are stored in Server)
Problem:
- Double-click "Acrobat 9 Pro" to run the software, it hangs
or
- Click one PDF file and use "Open with" to select "Acrobat 9 Pro", it
hangs again.
Does anyone have the same situation or have any idea to solve this
problem?
I really appreciate your kind help.
Best,
Ei-Wen

Home>Library>Preferences>com.apple.SoftwareUpdate.plist. Trash this file, repair permissions and restart your computer. Empty the trash when done.
P.S. If you shut down your computer, the window should have disappeared. Why didn't you use Force Quit?

COM+ Event System failed to fire the StartShell and Logon method after installation of PM 1.43

Hi Guys,
After installation of Power Manager 1.43, the following errors were immediate shown at event viewer: COM+ Event System failed to fire the StartShell and Logon method on subscription {F6FE5592-FCBC-44AD-A836-D37F5085ED5B}-{00000000-0000-0000-0000-000000000000}-{00000000-0000-0000-0000-000000000000}. The subscriber returned HRESULT 80004001.
Please advice if this is a known issue? Thanks!

Hello,
this is a known problem. See this thread
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

System does not turn off after halt after successful suspend-resume

I have the following problem: when I try to shut down my laptop after it resumed from suspend to ram. It seems to shut down normally until, at the very end, it reaches the system halted part (which you wouldn't even be able to read if the system would actually halt). I'm running an updated system, no testing, on an Dell Latitude E6400. The system shuts down normally if I don't suspend it.
Any ideas? What additional information do you need?

karol wrote:
iamsmrt wrote:It wouldn't accept keyboard input afterwards, not even magic keys.
I meant: turn off via 'sudo init 0' instead of 'sudo halt', not after.
Ok, wasn't sure. Isn't "sudo halt" effectively the same thing? How are they different?

Problems with System Update 3.14.0019 after installation SP2

Have you encountered problems with System Update 3.14.0019 after installation SP2 for Windows Vista?
After this upgrade I view this error: "An error occurred while gathering user information."
Thanks for the help

A known issue. It wasn't supposed to be supported until SP2 is RTM. However, look at the stickied post in the forum for some bad news about SU.
x61s

Is it possible to change our system SID and NR after installation

HI TO ALL
Is it possible to change our system SID and NR after installation os SAP r/3,
thanks

Hi,
It cannot be changed after you have installed the SAP system
You have the option to chose before you setup the system ie, during the installation.
Rgds
Radhakrishna D S
Edited by: Radhakrishna D S on Sep 9, 2008 7:08 AM

SLD: Duplicate Technical System after Installation Number change

We changed the installation number for a system. After this, inside SLD there are 2 entries for this system, with 2 different installation number (new and old). What is the correct procedure to remove one of the entry (old one).
Please advise.
A proper SAP note would be appreciated.
Thanks

Its ok even if you have forgotten to register to the SLD during installation.We can regaister after installation.Since SLD runs on java engine then if you go to http://<ipaddress or hostname of the server>:5<instancenumber>00/sld
If you go into that you can click on administration button and follow the instructions as in the link.
http://help.sap.com/saphelp_nw70/helpdata/en/31/f0ff69551e4f259fdad799a229363e/frameset.html
Difference between technical systems and business systems is that business systems are used in PI/XI.Whereas technical systems are nothing but your ECC , CRM etc.You have to use business systems only when there is a case for connecting to XI/PI.Hope i have answered your quesries if not please let me know.

After installation third Operation System my Imac(27) heating quikly and better.

Good Afternoon. After installation third Operation System my Imac(27) heating quikly and better.
I had MacOs and Win7 32bit(installed in Shop). It was ok.
But 32 bit OS didnt work with 8Gb RAM. Therethore i installed Win7 64 bit.
Now i Have MacOs, Win7 32bit, Win7 64 bit.
Before installation WIn7 64bit, in Win7 32bit my Imac was working in common mode(Internet\Video) without propeller noise. But now, i have noise after 10-15 minutes Video or Browser using.
In Win7 64bit i had more propeller noise and after 10-15 minutes play computer game, i have lags and troubles with performance!! My propeller's are spinning with maximal velocity(after 10-15 minutes). Therethore i cant play games\watch Video in my Win7 64 bit. I think that i must be install someone drivers?? I have BootCamp 4.0 under my Win7 64 bit.
In Win7 32 bit, i dont have problems with perfomance, but noise is really stronger than was early.
Please, Help me!
Sorry for my bad English.
Text for Russian employee:
Я купил Imac 27 с установленный МакОс и Win7 32bit. Всё было хорошо, но под 32 бита не работает 8гб Озу.
Поэтому я установил 64битку, но под ней сильно начинают крутится кулеры и вентиляторы. Примерно через 15 минут они крутятся на максимальной скорости!! Попробовал поиграть в игры, через 15-20 минут производительность начинает падать и начинаются "подвисания". Т.е. поиграть не реально. Да и при обычном сёрфинге страниц нагрев происходит быстро и кулеры начинают крутится быстрее.
Под 32 бита производительность не падает(мной замечено не было), но нагрев происходит быстрее и кулеры начинают крутится тоже быстрее. Даже при обычном сёрфинге уже начинается шум.
Не знаю по поводу нагрева, может он и в пределах нормы, но шума до установки новой винды было меньше!
Помогите разобраться с проблемой. Я не хочу потерю производительности под Win7 64бита и хочу уменьшить шум/нагрев под обеими Окнами.

Not using any mouse pad, I have a very smooth desktop. But I just tried to use a sheet of A4 printing paper, but no result, the problem persisted.
Someone on this forum suggested, that USB3 may interfere with the magic mouse.
I have 2 LaCie HDD's about 70 cm away from the mouse, I use them on Thunderbolt. But in operation or not - the result is the same, the mouse plays up! Just now I was clicking the desktop and the mouse created a new folder!!
Thanks for the advice, Bee
Cheers, Gerd

System halt after installation

Similar Messages

Maybe you are looking for