T60 - POWER FAIL - NO STATUS INDICATOR - NO DISPLAY - HELP !!!

Hello All,
IBM T60 wont power up - This worked fine the night before. This morning when i connected the power no status indicators on the front panel and on the LCD display when the power button was depressed. I noticed the hard drive power up and the network port showing send and receive lights. There is also light on the DVD drive bay.
I have checked the power adapter output and it says 20V on the multimeter. Kindly assist.
Thanks

try to take the ram modules under the palmrest and see whether the laptops beep when you start it without them.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

This device cannot start. (Code 10) Status Device Power Failure for Intel (R) Audio Display

Hi I just bought HP Envy M7 Sleekbook last week and upgraded from 8.0 to 8.1 for Windows 8.
Now I have no sound and this is the error message I get:
This device cannot start. (Code 10) Status Device Power Failure (for Intel (R) Audio Display)
under Sound, Vieo and Game Controllers in the Device Manager.
Anyone else having this issue after upgrading?
Getting a new lappy is stressful enough but to alreay have issues is ridiculous
If the upgrade is not the issue could something have happened in transit? (I have an issue with the way Best Buy packed it for shipment and wonder if it could have been compromised)
Any help is appreciated. Or should Ibe taing this back to best buy and have them address it?
Thanks
Pam

Ahmed, if your HP Envy has an Intel processor chances are it will be necessary to download new drivers for both sound and chipset due to compatibility issues with Windows 8.1. After 4-1/2 hours on the phone with various technical agents and a lot of frustration I finally got one who had the knowledge and training to resolve my issue. I believe he downloaded the new drivers from the HP support site. Good luck!!

DIsplay the status indicator as a circle on adf 11.6

I have requirements on status indicator as below .
Example : based on the employee count on employee table ,if the employees count is >10 means diplay the status indicator in red color ,if count <10 mean then display in green color .
I mean there any option to customize and display the status indicator in round shape in diffrent color each time based on the count .
Any hints ?
Thanks

You can use skinning.
.AFStatusIcon:alias: This icon gives a graphical representation that content is loading (e.g. carousel, inlineFrame). If you are editing this alias, you should also edit .AFStatusIconStyle:alias and .AFBackgroundImageStatus:alias since components will choose among these icons automatically under the necessary circumstances. This typically defines a content URL for an animated image, the width of this image, and the height of this image.
http://jdevadf.oracle.com/adf-richclient-demo/docs/skin-selectors.html

Status Indicator Light permanently off

Hi there,
I'm hoping someone can help me with this problem. I've set out some of the history too, as I have no idea whether this is hardware or software related. Apolgies for the length!
1) The immediate issue is that the status indicator light at the front of my black Macbook stopped working today. When I shut the lid or press the sleep option on the Apple logo in the top left corner, it remains off, even though it does appear to go asleep (makes the waking up noise when I open the lid).
2)I have followed the recommended procedures in Apple Help to re-set the PRAM and the SMC settings, and it made no difference.
3)My battery says it's charged at 100%. Here's the profiler report:
Battery Information:
Model Information:
Manufacturer: DP
Device name: ASMB016
Pack Lot Code: 0002
PCB Lot Code: 0000
Firmware Version: 102a
Hardware Revision: 0500
Cell Revision: 0102
Charge Information:
Charge remaining (mAh): 4029
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 4036
Health Information:
Cycle count: 403
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 12504
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 25
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 20
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 20
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 60
Revision: 0x0000
Family: 0x0085
Charging: No
4) I have no idea whether it's related, by my hard drive failed completely 3 days ago and was replaced (mechanical failure - sudden onset of click of death, spinning beachball, turned it off, wouldn't turn on, no data recoverable). When the drive was replaced (by Apple, but not under warranty), I also upgraded from Leopard to Snow Leopard. The light seemed to work until today though.
5) This is the third time the drive has failed in the same way and been replaced. The computer is 3 1/2 years old, and first failure happened about 7 months in. Second failure a year ago. Third three days ago. Apple say 'drives fail'. I am a very careful and unadventurous user of my MacBook. I do carry it around, but for large amounts of time it sits quietly on a table, using only licensed software to do not very challenging tasks. Does anyone have any ideas as to why 3 failures?
6) Yesterday I installed Dragon Dictate for Mac 2.0, which seems to be full of bugs and keeps crashing. This morning it was hanging and I tried to force quit but couldn't. I was then able to quit it normally, but the force quit window was still open and I could neither cancel nor make it force quit, and had to shut down the computer and start again.
7) It was after this that I notice the SIL issue, but can't say whether it was working immediately before. I know it worked initially after the Dragon install.
Thanks in advance for any help.
Message was edited by: gregormac

I don't seem to be able to edit the post above, hence this update.
I closed the lid and left the machine to sleep overnight, and when I woke up this morning the SIL light was on, and now appears to be working as normal each time I close it.
So my question now is:
a) If it happens again, is it something to be worried about?
b)re my point 5): can anyone think what would cause three hard drive failures? In particular, if it's something I'm causing, I'd like to know how not to cause it!
Thank you.

Facebook timed out while writing a post. Any attempt to open FB, now shows post that was in progress and immediately crashes app. Cannot clear timed out item. Have power failed and done warm reboot on iPad.   Is Delete/Reinstall only option?

Was writing post, as part of sharing article from my newsfeed.   While writing, Facebook timed out. Display cleared. App recycled and returned to newsfeed. This has happened previously and for all purposes, the original post, since it had never been "loaded" onto FB servers effectively was deleted from iPad memory. That appeared to be the case yesterday; as I was able to continue reading, sharing and commenting on other articles.
Later, as I was shutting iPad down for the night, scrolled through open Apps and discovered the original FB window was still "open" I'd apparently been working on a 2nd or mirror version of the app. Attempting to access the original page; it opens, but I am unable to "interact" with the display/app, pressing "cancel" on my original post has no effect. Within 5-6 seconds FB crashes.
I power failed the iPad, left it over night and today am encountering the same problem.   Tapping FB icon, brings up the post that was timed out. It displays for 2-3 seconds max, then original article and partial post disappear. Newsfeed appears to be loading as that and contact columns are visible in light font indicating they are preparing to load.   2-3 seconds, that vanishes. Am left with blue header band, spinning wheel indicating it is trying to communicate or process something.   2-3 seconds and then screen goes black and I'm returned to my app desktop.
If I immediately tap icon to reopen I get white screen, with blue header band.   2-3 seconds, black screen, back to app desktop.   If I wait 2 minutes, I get the full shared article, partial post as described above. I've confirmed in the problem log that this is failing in Thread 0 and showing up as system crash.
Based on feedback to somewhat similar FB problem I found in forum; in addition to doing power fail. I also did warm reboot (Home and Sleep keys) in hope app would reboot along with ios. No change.
At this point, I'm assuming my only viable option is to delete the app and reinstall it from App Store. Easy enough to accomplish. But wanted to see if there were any other recommendations, or whether anyone else has experienced a similar failure with FaceBook.
Thanks for your assistance.

Was writing post, as part of sharing article from my newsfeed.   While writing, Facebook timed out. Display cleared. App recycled and returned to newsfeed. This has happened previously and for all purposes, the original post, since it had never been "loaded" onto FB servers effectively was deleted from iPad memory. That appeared to be the case yesterday; as I was able to continue reading, sharing and commenting on other articles.
Later, as I was shutting iPad down for the night, scrolled through open Apps and discovered the original FB window was still "open" I'd apparently been working on a 2nd or mirror version of the app. Attempting to access the original page; it opens, but I am unable to "interact" with the display/app, pressing "cancel" on my original post has no effect. Within 5-6 seconds FB crashes.
I power failed the iPad, left it over night and today am encountering the same problem.   Tapping FB icon, brings up the post that was timed out. It displays for 2-3 seconds max, then original article and partial post disappear. Newsfeed appears to be loading as that and contact columns are visible in light font indicating they are preparing to load.   2-3 seconds, that vanishes. Am left with blue header band, spinning wheel indicating it is trying to communicate or process something.   2-3 seconds and then screen goes black and I'm returned to my app desktop.
If I immediately tap icon to reopen I get white screen, with blue header band.   2-3 seconds, black screen, back to app desktop.   If I wait 2 minutes, I get the full shared article, partial post as described above. I've confirmed in the problem log that this is failing in Thread 0 and showing up as system crash.
Based on feedback to somewhat similar FB problem I found in forum; in addition to doing power fail. I also did warm reboot (Home and Sleep keys) in hope app would reboot along with ios. No change.
At this point, I'm assuming my only viable option is to delete the app and reinstall it from App Store. Easy enough to accomplish. But wanted to see if there were any other recommendations, or whether anyone else has experienced a similar failure with FaceBook.
Thanks for your assistance.

Status Indicator Light not working

I've been having a recurring issue with the status indicator light on my 15.4-inch MacBook Pro 2.8 GHz (Mid-2009). I learned recently that it's normal for the status indicator light to be on when the computer starts up, shuts down and goes to sleep. Lately, the status indicator light has not appeared at all when the computer starts up, goes to sleep, and shuts down. I've tried almost everything and still nothing has worked
1.) Checked to see if any of the ports are working: FireWire, Ethernet, MagSafe, SD card, USB, Mini-DisplayPort. These ports are behaving as normal, working fine.
2.) Checked and successfully paired a seven button Apple Remote to test the IR receiver.
3.) Ran an Apple Hardware Test, found nothing wrong, passed the test.
4.) Reinstalled and erased my hard drive, still having issues.
5.) Bluetooth, AirPort Extreme, microphone, audio ports, speakers, and iSight are working.
6.) Battery works and the charger is working.
7.) Backlighting for display and keyboard work.
The computer is only 1 year and 4 months old. The issue began occurring two months ago. Now the computer does sleep, but if the fans are going, it takes a bit longer for the computer to go to sleep when I close the lid.
I haven't replaced the hard drive or installed any new hardware.
The battery and power information is still at 100%:
Model Information:
Serial Number: W0945***7VC
Manufacturer: SMP
Device name: bq20z451
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0003
Hardware Revision: 0003
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 4165
Fully charged:No
Charging: Yes
Full charge capacity (mAh): 6662
Health Information:
Cycle count: 43
Condition: Normal
Battery Installed: Yes
Amperage (mA): 3177
Voltage (mV): 12109
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 15
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: Yes
GPUSwitch: 2
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
GPUSwitch: 2
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0100
Wattage (W): 85
Revision: 0x0000
Family: 0x00ba
Serial Number: 0x009fe8db
Charging: Yes
My computer's warranty with Apple, including tech support, service, and repair, has expired. However, I do have a remaining two year warranty with Best Buy Geek Squad.
I'm wondering how much would it cost out of pocket to take this computer to an Apple Store for service and repair with a Mac Genius?
So is there anything that could be wrong with this computer and if so, please help!
<Serial Number Edited by Host>

studabaker wrote:
I erased the disk with Disk Utility using the installation DVD ....
If you used "Secure erase", you can be certain that there is nothing left on the disk that is causing your problem.
Because you have a long wait for access to an Apple Authorized Service Provider, if you merely clicked "erase" (the one that does not take more than an hour), you could try Secure Erase now if you want to try the final possible fix you can do on your own.
... and installed the combo update recently, the size for that update was over 1GB.
That is the right one.
I have been regularly doing those permissions. Thanks for the suggestions.
You're welcome.
I'm taking my Mac to Geek Squad and Mac Genius next month when I visit my dad in Georgia, there's an Apple Store about 45 minutes away from his house and a Best Buy that sells Macs, cause it turns out Geek Squad's coverage for Apple/Mac is only in places where they sell Macs. I used my zip code and turned up 0 results but I typed the zip code for where my dad lives in North Georgia, and a Best Buy in Atlanta is available. So I will definitely go there and visit the Apple Store to at least see what my options are.
If you need help from Apple before you can go to a physical location next month, other Apple Technical Support service option contacts are available here:
http://www.apple.com/contact/
Best Buy by far has the best warranty for computers from what the sales associate was telling me. Apparently, Best Buy warranty covers spills, drops & breaks, and overall maintenance issues. In fact, they told me if the computer can't be fixed, they'll replace it with a new one.
It should surprise nobody when salesmen tell customers that their own warranty product is best. Because you have apparently already paid for the Best Buy warranty, you can take advantage of their warranty and enjoy the "best" results if you can find a location that honors it.
Thanks for advice and if there's anything else you can think of, let me know.
You're welcome. You have all my suggestions. However, if I think of anything else, I will post back here.
We will watch for your status update. Please let us know what fix works for you.
EZ Jim
Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.7); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.7)
LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod4touch4.3.1

Network Connectivity Status Indicator for IPv6 works wrong in Windows 7 and Windows 8

Hi Folks,
I am working on testing Network Connectivity Status Indicator for IPv6 in Windows 7 and 8.
Waht is "Network Connectivity Status Indicator(NCSI)" you can refer to https://technet.microsoft.com/en-us/library/ee126135%28v=ws.10%29.aspx?f=255&MSPPError=-2147217396
I found that even if Network Connectivity Status Indicator detect IPv6 connection to http://ipv6.msftncsi.com/ncsi.txt failed.
Windows IE still use IPv6 to connect to website first, rather than stop using IPv6 and to use IPv4.
It will cause IPv6 fallback to IPv4 problem, that's 21 secs and 7 secs delay for fallback in Windows 7 and 8.
Does anyone suffer the same problem?
Or someone know how this works?
Thanks!

Hi Roger_Wang0214,
"Windows IE still use IPv6 to connect to website first, rather than stop using IPv6 and to use IPv4."
By default Windows prefers IPv6 over IPv4,we can manually configure the IPv4 prefer over IPv6 if it has result in any troubles.
Here is a link for reference :
Resolving Internet connectivity issues after World IPv6 Launch (June 6, 2012)
https://support.microsoft.com/en-us/kb/2533454
"The "Prefer IPv4 over IPv6" Fix it solution will configure your computer to prefer IPv4, instead of IPv6. By default, Windows prefers IPv6 over IPv4. If you are having problems using IPv6 to connect to some websites, this may resolve the
problem."
For a Windows 7 machine ,we can try the following fixit tool to configure IPv4 prefer over IPv6 .For a Windows 8.1 machine ,we can configure it referring to the manual part .
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip6\Parameters\DisabledComponents
If the DisabledComponents entry is unavailable, we can create it (DWORD (32-bit) Value).Then set a value with "0x20"to prefer IPv4 over IPv6 by changing entries in the prefix policy table.
Here is a link for reference :
How to disable IPv6 or its components in Windows
https://support.microsoft.com/en-us/kb/929852
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

I'm in need of a 90w power bloc for my 23" HD display

I'm in need of a 90w power bloc for my 23" HD display as mine is failing.
Anyone got an extra?
A1097
<Email Edited By Host>

John, please refrain from posting your personal email in these threads. It is not necesary and all communication to you can be done directly in these forums. Posting your email address can open up you to tons of unwanted spam, among other things. Really all you can do is search the internet for them. My suggestion would be to google "case for late 2007 macbook pro".
One will probably be very hard to find for a 6 year old model as it is on the borderline of being considered "vintage". Ebay may be a good place to try too.

OS X does not boot, a status bar is displayed

The system starts booting and the standard grey screen appears. In addition, a status bar is displayed below the spinning circle. It disappears after going to 100%, but nothing changes. The system hangs at the grey screen.
I have recently installed Windows with a trial of MacDrive. I have not used my OS X for a couple of days.
I had installed and then disabled Mac FUSE, however there might have been a couple successful boot sequences afterwards.
I tried starting system from a Mac OS Install DVD. Disk utility found errors and failed to repair them. I could format the drive, but this is terribly time consuming....

Thank you for the contribution. Sadly, the cmd + v did not work- I tried a couple of times without any result.
I have decided to reinstall the OS after all attempts to repair the disk failed. However, it is not that simple. The partition does not show up at the "Where do you want to install Mac OS X to" menu. Furthermore, erase fails as well- the Disk Utility appears to be unable to mount the disk. The bar is basically stuck at approx 3/4 for 15 minutes now....
Restarting and retrying failed.

Excite Pro - Battery Status Indicator at 0%

Battery status indicator is stuck at 0% - battery holds charge ok just don't know what it is. I presume the battery stats file is corrupted - is the only way to fix it a factory reset?
Calibration either needs root - not possible or 60% charge - won't work as says 0%!!!!

I think you should set it to factory settings.
Press and hold power button and volume up button. Then in the menu choose factory reset.
If this will not work, then the issue must be related to hardware failure

IDOC Posting To XI Failed With Status Text "::000" in SM58

Hello Gurus
Can u please suggest me how to overcome the problem with Custom Idocs while trying to send from SAP R/3 to SAP PI(XI).
The status text is displaying as "::000" with no other details, in SM58 of the sender system i.e. SAP R/3.
The Idocs status in the sender system is showing as 03 with the message "Idoc sent to sap system" in transaction BD87.
So I am getting confused where I missed the configuration.
Please suggest how I can troubleshoot the above.
<<Text removed>>
Regards,
Rk.K
Thanks in advance .
Edited by: Matt on Jun 24, 2011 9:58 AM

Thanks a lot for your support.
I have tried all the suggested solutions......but my problem was not solved.
The Metadata should be automatically created when the IDOCS successfully received by the XI server.
If it is not created then we should clear the SLD Cache in XI and try to create a new Metadata by giving the Custom IDOC Name and Port.
Even I tried with a Standard Idoc ORDERS05 , but I failed to do so.
After doing the above step I am getting the Information pop-up message "I::000".
Regarding RFC, I have created 2 users in both the systems with the same name(ALEREMOTE) of type "System".But,I am unable to Remote Login from XI to R/3 whereas the vice -versa is successful.
Are there any chances for this being the reason for failure of Idoc processing?
Such information message"I::000" is completely inexplainable.
Kindly, suggest a solution for it.
Thanks.

Pull html from solarwinds for sharepoint status indicator.

Hi everybody had a question not sure if this is possible. I want to put a status indicator image from Solarwinds on our sharepoint site. Im not sure what kind of html code that requires but let me try to explain.I need sharepoint to go and check the nodes site Here: http://solarwinds/orion/node.aspxI need it then to grab the nodes status in the html sourcehere:andTextthe status=1 decides if it is green or red 0 is offline 2 is redSo wants it grabs that 0, 1, or 2 I need it to give that to SharePoint so it can tell me if its status.I was then going to add a url to the pc name to take me out to solarwinds for more info.If anyone knows a way to do this let me know I have been looking into it for 2 days with no luck.
This topic first appeared in the Spiceworks Community

Thanks for your efforts and help.
I implemented the above condition.Its working fine for several situtations except the below one.
The client creates a ticket and the support team members are closing it with Root Cause and Resolution.
The client is not satisified with the response and he is asking more clarity on the root cause and resolution.
So again the support team members open the existing ticket and they are trying to modfiy the Root Cause and Resolution fields.At that time the if the support team memebers are not providing root cause and resolution(I mean they removed the exisitng root
cause and resolution which was provided laready)then its failing.When i looked in to the workflow history i am getting values for empty multi line text box as
<div class="ExternalClass9E8676C798FA4CCEA5B78BEC226D8881"><p> </p> </div>.
<div class="ExternalClassDA7B4AE3074F4DE78FA582351C31485D"><p> </p> </div> <div class="ExternalClassF487CA8EBABA46A688E138D0841D364C"><p></p>
<div> </div></div>
I have modified my workflow to check for above values also but still its not working.Any thoughts on this.I dont my workflow to fail under any situtations.
Thanks, Vijay Arockiasamy

What is this Status Indicator?

My Question:
What is this status indicator? - to the right of the battery, with the number '1' and a circle with a downward pointing arrow?
Here is the URL for the pic...
    http://www.flickr.com/photos/80032181@N00/4500178608/
I have checked messages via - messages -> view folder -> then selecting each folder to see if there were any messages.
My carrier:
Sprint
Curve 8530
OS version - v5.0.0.459
Apps and free space:
File free = 103103680 bytes
All core apps at - v5.0.0 except:
    BB App World - 1.1.0.33
    Docs to go - 1.008.012
    Facebook - 1.7.0.22
    Bible - 2.1.2
    Bolt - 1.70
    DriveSafely - 1.17
    Google Maps - 3.2.1
    Pandora - 1.1.3.2
    Pocket Express - 5.1.15
    Sprint Navigation - 2.8.0.1197
    The Weather Channel - 1.5
    Weather Bug - 1.1.0.146
    Bluetooth - disabled
Solved!
Go to Solution.

Your link is dead.
That notification indicates you have an application which you previously downloaded or purchased in App World > My World, which is ready for an upgrade on your device. Look there for the upgrade.
To clear the onscreen notification, find the corresponding alert message in your main messages folder, read it or clear it.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Facebook status indicator error

I've had the application installed for abouth a month now and this is the first time this happens. The facebook status indicator keeps coming up. I have checked all messages and they have all been read. Is there any way to just delete that?
Thanks!

Where is the status indicator showing?
On your BlackBerry Homescreen, at the top?
On the Facebook app icon itself?
When you are IN the Facebook at, on the top row of icons, do any of those show the red star?
With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot.
Does the indicator still appear?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Unrecognizable status indicator for tour

I have a status indicator on my display, top left corner, which looks like a circle with an arrow pointing down towards the center, with red asterick and a 1 next to it. I have opened every application I have and cannot figure out WHAT this one means. Sometimes also my facebok icon shows 2 yet I dont have any that have not been opened or taken care of. Is there a clear icon I can use?
I have taken the battery out and rebooted and still there....can anyone please help?

Ok figured out finally it means there is an update to one of the applications....now my question is, NONE of my apps show that they need an update....I have opened each one and none have given me an update option....I would love to get rid of this indicator so can anyone please help?

T60 - POWER FAIL - NO STATUS INDICATOR - NO DISPLAY - HELP !!!

Similar Messages

Maybe you are looking for