Telling if client is on N in 891W router

We have an 891W wireless router on which we have enabled 802.11n speeds. When we connect with a 802.11n laptop client, it seems to be connecting on non-N data rates. We're trying to figure out if we've missed something in configuring the router or something that needs to be done on the client to make it connect on N speed. Any assistance would be greatly appreciated. Thanks.
===
Here's our show int command which shows that N is enabled on the radio:
wap-temp-rtr#sho int dot11Radio 0
Dot11Radio0 is up, line protocol is up
Hardware is 802.11N 2.4GHz Radio, address is 0027.0df0.a730 (bia 0027.0df0.a730)
===
Here's the output of the show dot11 command that seems to indicate that the client is connecting on B/G speeds:
wap-temp-rtr#sho dot11 asso 0022.fbca.3a70
Address           : 0022.fbca.3a70     Name             : wap-temp-rtr
IP Address        : 10.1.10.41         Interface        : Dot11Radio 0
Device            : ccx-client         Software Version : NONE
CCX Version       : 4                  Client MFP       : Off
State             : Assoc              Parent           : self
SSID              : temp
VLAN              : 1
Hops to Infra     : 1                  Association Id   : 2
Clients Associated: 0                  Repeaters associated: 0
Tunnel Address    : 0.0.0.0
Key Mgmt type     : WPA PSK            Encryption       : TKIP
Current Rate      : 54.0               Capability       : WMM ShortHdr ShortSlot
Supported Rates   : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates       : disabled           Bandwidth        : 20 MHz
Signal Strength   : -62 dBm           Connected for    : 3689 seconds
Signal to Noise   : 34 dB            Activity Timeout : 20 seconds
Power-save        : Off                Last Activity    : 0 seconds ago
Apsd DE AC(s)     : NONE
Packets Input     : 22964              Packets Output   : 23222
Bytes Input       : 2455552            Bytes Output     : 22794389
Duplicates Rcvd   : 2                  Data Retries     : 6834
Decrypt Failed    : 0                  RTS Retries      : 0
MIC Failed        : 0                  MIC Missing      : 0
Packets Redirected: 0                  Redirect Filtered: 0
Session timeout   : 0 seconds
Reauthenticate in : never
===
Here's the relevant parts of our configuration:
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
broadcast-key vlan 1 change 45
ssid temp
antenna gain 0
channel least-congested 2412 2437 2462
station-role root
end
dot11 ssid temp
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   infrastructure-ssid optional
   wpa-psk ascii 7 <removed>
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled

Well... that client will never connect via 802.11N. The reason is that the 802.11N standard does not support tkip. So if you change the encryption to WPA2/AES or leave it open and make sure you channel bond (40mhz) channel width, then you might be able to connect using 802.11N. Hope this helps.

Similar Messages

Connecting to a Client behind a RRAS and a Router:

My setup:
(ip numbers are examples, not real configs)
Router:
IP 192.168.1.1
Mask 255.255.255.0
Gateway 192.168.1.1
DNS: Provided by ISP
RRAS 2012 R2 NIC1
IP: 192.168.1.2
Mask: 255.255.255.0
Gateway: 192.168.1.1
DNS: 192.168.1.1
RRAS 2012 R2 NIC2
IP 10.1.1.10
Mask 255.0.0.0
Gateway: none
DNS 127.0.0.1
So everything works fine but lets say i have a client that has de ip 10.1.1.15 and i need to RD that one. I know that this might be a stupid question but how do i route a remote desktop through two different networks?

I am unable to connect from an external. Connecting to the RDS Server ( I said client, i know, sorry) with a client PC works fine. The tutorial you posted is the one i used to install the RRAS role and it works fine as intended (internet connection for the
users).
So, how do i connect from my home PC to the RDS server? I tried to use a random port (2212), which i forwarded like this:
From: All external IP's
To: 192.168.2.4 (static RDS server ip)
External port: 2212
Destination port: 3389
This did not work, probably because the Router ip is 192.168.1.x with a 24 bit subnet mask.
Then i tried this:
From: All external IP's
To: 192.168.1.49 (public NIC of the server that has the RRAS role installed)
External port: 2212
Destination port: 2212
On the RRAS server i forwarded the request, in the Advanced Firewall settings, from port 2212 to port 3389 and added the ip number of the RDS server as the destination IP. I have not changed anything on the RDS server, since RDP is open on all network types.
I am probably way off from the solution for getting this to work properly.

Can't get embedded AP on 891W to accept clients

Hi all.
I have a very simple configuration that I'd like to do, which I have done before, but yet can't do now.
I have an 891W router, the embedded ap801 instad. IOS on both is 15.2.
I have an SSID set up, using wpa-psk. I have a fully working configuration identical to this at a customer site, yet here, I do the same configuration and all of my wireless devices cannot connect (they do see the ssid broadcasting though).
I really have no idea how to troubleshoot, since comparin this configuration to a working one reveals they are done the same. The difference here, I have no LAN cables connected to WAN or LAN ports, but I don't see how that should matter if trying to connect by WLAN and get an IP via DHCP from the router.
Actually now that I think about it, one difference: the working config, they have a DHCP server on a Windows server - here, I have DHCP set up on the IOS router itself. So maybe the inability to connect (Apple and Windows devices just say "can't connect", notthing more specific...) is just that it can't get an IP via DHCP ?
Is therer a way via the IOS on the AP to look at logs, debug, or what not to see if clients are connecting but perhaps just nogt getting DHCP through to the IOS on the host router?

Hi Steve, I"ll continue on this issue startingt today. I had gotten buried under a bunch of work and just got out now
Give me a bit to reply with the inf you requested. But first, I"m going to try everyting again just to make sure the issue hasn't changed.

Clients can't rejoin domain after server clean install

Hello, I've got an issue with having client computers rejoin the domain after reinstalling the server software. Another post I read suggested saving the plist files to get the settings the same, but I need to reconfigure manually to eliminate some other problems we've been having.
We've got an Xserve running 10.4.8 with a mix of XP and Tiger clients all authenticating with the server. Our XP clients have remote profiles converted to local and our Tiger clients use mobile accounts. Generally things were running OK, but we kept having some authentication issues and have SMB crashes. In reviewing our log files it was suggested that our Open Directory was messed up (probably during our upgrade from 10.3 to 10.4) and that a clean install was the best course of action. The server has been running 24x7 for over 3 years without any signifigant maintenance, so this seemed like a good idea.
Everything was going great. I did the clean install and had DNS and DHCP configured and working, then started setting up Open Directory as the PDC and Windows Services as the Primary WINS. I had intended to recreate the user accounts because I didn't want to reintroduce problems by restoring the settings, however when I added one account and tested logging in on a XP machine it couldn't authenticate even though the domain name and user name was the same as before (short names too). On a whim, I moved the computer from the domain to WORKGROUP and then rejoined the (new) domain. Upon login it created a new roaming profile named user.domain instead of using the other account already there. On the XP client in accounts, the old profile showed up as unknown. I then went to a Mac and tried to log in and had similiar issues not finding the authenticating server.
After pulling my hair out this evening and realizing that there was no way I was going to have the office operation in the morning, I did a full restore from backup and pretended like I hadn't just wasted my weekend. After I got the server running, I was able to get my client machines to see the domain again and all is as it was.
Soooo, now the question is how do I create a clean installation with newly created user accounts and get the client computers to recognize the domain server as the same old one? Is there a hidden domain ID or something that is telling the client computers that it isn't the same domain or LDAP server? Any suggestions would be greatly appreciated.
Thanks.
xserve G4 & XRaid Mac OS X (10.4.8)

Sorry, to clarify I did not want to use the archive & restore because I didn't want to reintroduce the errors I was trying to eliminate. I setup the Open Directory as a PDC from scratch and then ran into the client authtenication issue. In a desperate attempt to salvage the situation I did restore the previous settings which (A) didn't work and (B) may have made things worse because I already had created some groups and a few users and ended up with groups with duplicate IDs. That was when I scrapped everything and restored the disk from backup.
Your idea of using export/import is a slightly different avenue. However, now that I'm thinking about it, I didn't even get far enough for the user profiles to be an issue because the client computers weren't even communicating with the server to get the list of users (the Macs log-in by selecting a user name from a list).
Does export/import of a computer list work? I think I tried to import the computer list last night and the one I had only contained the Macs and these didn't preserve the MAC address info for some reason. I didn't have an export of the XP machines, but tried to manually add them to the list with no success.
Thanks again for your help.

The best way to upgrade j4w on client computers?

Hi Together
What's the way to upgrade J4W on client computers when the logged in user hasn't administrator permissions?
We are planning the rollout through our central software deploying system. For a later upgrade we wish to use the build-in upgrade procedur from J4W. This option is much easier.
I guess if jabber prompts the window to install an upgrade, a normal user can't do that, because of the missing administrator rights. Is that's true?
How do you that or what's the best practice?
Thx for help
greetings Phil

I'm pretty sure Jabber for Windows requires local admin rights for both the initial install and any updates. Modern Windows apps are getting past this need by installing a wrapper exe in the admin-protected Program Files locations while installing the core app bits in user-level places like %appdata%, but I don't believe Jabber is on that bandwagon yet. Modern apps that take that approach can be updated without admin rights (and also note that this plays very nicely with most antivirus programs too). i think the native Jabber "update" mechanism is more of a notification tool than an updater. You're provider a URL, and telling the client an update is available, but the end user is still in the driver's seat on doing that upgrade (which they're running with their own rights on the local machine).
That said, if your end users don't have local admin rights, you're probably stuck using your central deployment tools for the MSI.

How to update client profile manually (without APNs)

Currently implementing an OS X Server with a specific goal of device management using the Profile Manager. I have a thorough understanding of APNs roll in this where communication is sent to APNs which then gives the client a notification to "check-in" with the server for updates. So the actual data exchange is only between the server and client. (Like the diagram below...)
However, for security reasons I want to be able to accomplish Client-Server mdm checkin manually without APNs if I want to. In theory, this should be possible because the client obviously runs code to search for the server, communicate, and apply any changes to its configuration profile. Based on the OS X server documentation for this, it does this over SSL to the server for an mdm_checkin. The client also automatically checks the server on each startup, so restarting the machine does in-fact tell it to check the server and gets any profile changes that are holding as tasks. (Obviously, its not ideal to restart every time I want a change...)
Again, for security and troubleshooting purposes, I want to avoid APNs and do this communication manually. I'd also like to avoid downloading from the myDevices portal, or transferring a profile to be double-clicked/opened, etc etc. However, for the life of me I can't find any other documentation or code that may direct me how to do this! It seems like there should be sometime to run or few terminal commands to accomplish this...
Has anyone else attempted this or had success telling a client manually to talk to it's mdm server? (or even using mdmclient?)
Thanks!

Enrolling a device to an MDM e.g. Apple's Profile Manager does not require APNs, it merely requires 'installing' the enrolment profile and optionally a trust profile. However normally if you make a change to a profile this would be 'pushed' to client devices by sending an APN message to tell the client to 'phone home' to download the new profile.
I install the trust and enrolment profiles during a DeployStudio imaging workflow and at the moment use APNs to send notification for updates, however for another different network I am looking at the following instead of APNs.
The latest Munki software now supports installing Profiles directly, before it used to be necessary to wrap the profiles inside Apple installer packages.
Note: Profiles can be distributed 'over the air' via APNs, hosted as files to b manually downloaded from a web server, or emailed to users/devices as a file attachment, and as mentioned above wrapped inside an Apple Installer package which would run a post-install script to install the profile.
Therefore you could generate the updated profile and use Munki 2.2 to manage distributing and installing the updated versions. Of course an important limitation is that Munki is for Macs only and does not cover iOS devices. Munki does not use APNs. The Munki client needs to be able to talk to your Munki server which ideally should only be contactable on your LAN, a VPN connection would work.
Note: It is probably not worth looking at Casper Suite even though it supports iOS as it uses APNs.

Installing oracle instant client 12.1 on Windows 8 with no previous Oracle Software

Hi all,
I want to install oracle client 12.1 on my 64bit windows 8 computer. Do i have to have an oracle software installed first?
I've downloaded all the packages from the oracle website ie, basic, odbc, jdbc, sqlplus and sdk
I have extracted them into one folder c:\Program Files\OracleInstantClient. as told to do in the documentation
These are the actions I have taken as suggested by different forums which i have done;
- created a system variable OCI_LIB64 and set the value to c:\Program Files\OracleInstantClient.
- created a system and user variable ORACLE_HOME and set the value to c:\Program Files\OracleInstantClient.
- created a user variable TNS_ADMIN and set the value to c:\Program Files\OracleInstantClient.
- create subfolders "\network\admin" in your 64-bit client folder and create sqlnet.ora and tnsnames.ora here ie c:\Program Files\OracleInstantClient\network\admin
In another installation guide i found, i was told to double click a setup.exe and start the GUI which i didn't see after i extracted all the downloads
Please am missing something? do i have to install oracle database first? i really don't need that.

You do not have to install oracle database in order to install oracle client. But it won't do any good to install the client if you don't have a database to connect to -- somewhere. It's just that the database doesn't have to be in the same box as the client. In fact, it usually isn't.
You created a directory "c:\Program Files\OracleInstantClient\network\admin" to hold your tnsnames.ora and sqlnet.ora files. But then you set tns_admin to point to some other directory. If you set tns_admin, you are telling the client THAT is where it should locate the tns config files.
Oracle sometimes doesn't like putting things in Windows folders that have embedded spaces in the folder name. I'd avoid it like the plague.

IOS4, apple-mobile-web-app-capable and client certificates

IOS4 (4.0 and 4.0.1) seems to have broken apple-mobile-web-app-capable. I have a webbapplication using client certificates to authenticate the user. This worked flawless on IOS3.x. However, after having upgraded my iPhone to IOS4, the application fails when started from the springboard with an error message telling a client certificate is required (I have one installed). When I start the application from within Safari it works OK. I tracked the error down to the following line in the HTML code:
<meta name="apple-mobile-web-app-capable" content="yes" />
When I remove this line, the application works again flawless when started from the springboard. However the native look and feel are gone. As soon as I add this line to the HTML, the application works when started from Safari, but fails when started from the springboard.
Does anyone have a glue or is this a bug on the apple-mobile-web-app-capable function of IOS4?

I have also experienced this problem on iOS 4.1. I want to authenticate access to a web-app using SSL client certificates but I get an error "Cannot Open ... requires a client certificate" when launching the app from the home screen. Very annoying!
Navigating to the page in Safafi prompts the user to choose which certificate to use and then loads the page successfully. Just as a side question, is there anyway to automatically associate a client certificate with a web site so that the user is never prompted to choose a certificate when accessing the site? I want an authentication process that is transparent to the user.

COBOL client unable to call Tuxedo methods (CSIMPAPP tutorial for Windows 2000 OS)

Hi,
This relates to another post below. I have compiled the COBOL client and the COBOL
server and produced .exes however when I get runtime problems now
I get the message: exec CSIMPSRV -A CMDTUX_CAT:819 INFO: Process id=1912 Assume
started (pipe) but when I do tmadmin/psr, the process is (DEAD)
Also when I run the client I get an error as soon as the client gets to a call
to a Tuxedo method e.g. USERLOG or TPCALL, i get an error message
Load error : file "USERLOG"
error code 173 pc=0, call=1 seg=0
173 called program not found in drive/directoryI have added %TUXDIR% to my path and everything.
Any suggestions?
Thanks
Colm

Winfried - Thanks for that, this might mean something
These are the steps I take:
Compile the CSIMPCL.cbl file using the COBOL.exe command ( Mcrofocus/NetExpress/bin)
etc
Then
cblnames -v -mCSIMPCL CSIMPCL.obj
buildclient -C -o CSIMPCL -f CSIMPCL.obj -f cbllds.obj
ALl compiles ok - then when I run CSIMPCL.exe I get the error as detailed below
already
Load error : file "USERLOG"
error code 173 pc=0, call=1 seg=0
173 called program not found in drive/directory
However I got mailed a copy of CSIMPCL.obj which had been built with Net Express
4
then
cblnames -v -mCSIMPCL CSIMPCL.obj
buildclient -C -o CSIMPCL -f CSIMPCL.obj -f cbllds.obj as before
When I ran it ( without booting the server - just telling the client to send a
message to the BBL and display a response) it ran fine
so i think the COBOL.exe in Net Express 3 is not creating the obj file properly.
I haven't hooked it up to WTC yet but it should work
Any views you have are much appreciated. I'd be loth to blame a compiler if I
hadn't some variable set but all the environmental variables seem to be in the
path.
"Winfried Scheulderman" <[email protected]> wrote:
>
Colm,
Looks like a general problem running Cobol to me.
The first message indicates something went wrong during server startup,
see e.g.:
http://support.bea.com/application?namespace=askbea&origin=ask_bea_answer.jsp&event=link.view_answer_page_clfydoc&answerpage=solution&page=tux%2FS-03850.htm
and
http://support.bea.com/application?namespace=askbea&origin=ask_bea_answer.jsp&event=link.view_answer_page_clfydoc&answerpage=solution&page=tux%2FS-16674.htm
The cause for this is probably the same as for other error message.
You should check the settings for running Cobol programs (clients and
servers),
especially the library path.
Winfried
"Colm O'Regan" <[email protected]> wrote:
Hi,
This relates to another post below. I have compiled the COBOL client
and the COBOL
server and produced .exes however when I get runtime problems now
I get the message: exec CSIMPSRV -A CMDTUX_CAT:819 INFO: Process id=1912
Assume
started (pipe) but when I do tmadmin/psr, the process is (DEAD)
Also when I run the client I get an error as soon as the client gets
to a call
to a Tuxedo method e.g. USERLOG or TPCALL, i get an error message
Load error : file "USERLOG"
error code 173 pc=0, call=1 seg=0
173 called program not found in drive/directoryI have added %TUXDIR% to my path and everything.
Any suggestions?
Thanks
Colm

BPC Report emails only work from server (not client) - BPC v5.1

Hi all.
Hope someone might have seen something like this before.
Basically, I setup our servers to send email from BPC about 3 weeks ago.
(NB - If it makes a difference, we use Lotus Notes via a Domino server)
The SMTP settings are all correct in BPC WebAdmin, the servers have been added to the allow list on the mail server and the port is open.
Anyway, when I try to send mail from a client (using the Offline Report Distribution Wizard), I get the following error:
"The transport failed to connect to the server".
At SAP's suggestion, I ran a test by installing Office and a BPC client directly onto the Web Server.
When I ran the wizard from the server, the email sent perfectly.
The problem I have now is that although I informed SAP of the test outcome, I haven't heard anything back in about 3 weeks, and I really need to get the reporting email system up and running properly.
Does anyone have any suggestions on what could be causing this?
It's as though the system is telling the client to send the email itself, via the forwarding server, but this would mean allowing every user PC to access the mail server.
Hope you can help, but thanks for looking either way.
Craig

Hi Ludovic
The problem turned out to be mail server white-lists, due to the way that BPC sends emil.
Although you setup the email account/profile on the server, it actually sends from the client PC of whichever user makes the email request.
Our system is only configured to block all email requests with individual exceptions (ie a White-List).
It needed the PC of every user who would need to send email from the BPC system to be added to the white-list.
This is why it worked from the server, as we had added the server address to the list as part of the testing.
Not reall y a BPC problem, more of an issue with functionality due to the method that it uses to send the messages.
Hope that helps
Craig

Issue with vlc steaming through dolphin ftp client

I am not sure if i should post this here or in the multimedia section excuse me if i am mistaken. I have been using archlinux in almost 4 weeks with gnome 3. I have installed kde today after removing gnome(pacman -Rscn gnome). I have a small home server running ftp server where i have some media files(.mkv). In gnome i usually used nautilus to access the ftp folder(sftp://servername.dyndns.org/srv/) and run vlc to stream the medias. Tried to do the same with kde dolphin with no luck.
First i was not able to view the folder with dolphin. I researched abd found this thread with a solution:
http://forum.kde.org/viewtopic.php?f=18 … 5&start=15
Now i am able to access the folder, but can't stream any media using vlc.
The following errors are from vlc:
Your input can't be opened:
VLC is unable to open the MRL.
sftp://servername.dyndns.org/srv/filename.mkv
Check the log for details.
Going into tools->messages gives the followings:
main error: open of
sftp://servername.dyndns.org/srv/filename.mkv failed:(null)
I suspect something is wrong the ftp client configuration in dolphin. This bug report also bothers me also :
http://old.nabble.com/-Bug-274170--New% … 05158.html
Other thing is that i am able to open the media files using other media players(dragon player, mplayer), but then the files are automatically downloaded into the local folder /var/tmp/kdecache-username/krun/filename.mkv. The media player then loads the file from there. Its the same if i open a text file in the server, edit it and save it. Its first downloaded to the /var/ folder then asked to upload back to the server when closed.
Its my conclusion that the ftp client in dolphin does not work properly or KDE KIO works different then whatever is used in gnome/nautilus. I hope i have explained the issue as good as possible and would appreciate any help or lead to how to solve this.

Thanks for your reply, after checking some ideas I found that to get the ftp to work I needed to use the internal IP 10.0.0.1 for it rather than the old normal IP like before the firewall(probably a very beginner error sorry for that). And I discovered the exact issue causing clients to not see their characters if not using Hamachi.
Hamachi treats everyone join to the network as though they are local I believe, so when the server send character info via Hamachi it thinks it is sending the info locally and then Hamachi itself sends it out to the extrenal client, while tracing the data I found that the login process sends a 33 byte packet of data to the client via TCP from port 5051 out to the client on a rnadom port usually in the range of 40000-50000 telling the client to send a request to the other process to ask for the character information.
Now for some reason I see when a client logs in through Hamachi that packet is sent correctly to their Hamachi IP and recived fine.(sent from 10.0.0.1:5051 to the Hamachi IP:40k-50k) but when a client tries to log in using a normal IP with Hamachi turned off, the log in process does send the 33 byte packet from 10.0.0.1:5051 to the client WAN IP through the usual port but the client never recieves this packet and as such doesn't not request the character information.
So my guess is something on the 5505 is disallowing the log in process to send the data externally to the clients WAN IP's? Though this is very odd because it does allow the client to actually log in to the account and seems to recieve at least part of that information fine.
If any help that might resolve this for me can be given I would very much appreciate it, this issue is limiting my client base and as such my income and business as a whole. Thank you in advance for any help given.

How to enable traffic between VPN clients in Windows Server 2012 R2?

Hello,
I installed Remote Access role with VPN.
IPv4 Router is enabled: http://snag.gy/UAMY2.jpg
VPN clients should use static ip pool: http://snag.gy/REjkB.jpg
One VPN user is configured to have static ip: http://snag.gy/TWwq0.jpg
VPN server uses Windows Authentication and Windows Accounting.
With this setup, VPN clients can connect to server, get ip addresses and can see server via server's vpn ip. Server can connect to VPN clients too (Using client's vpn ips). But VPN clients can't communicate with each other.
For example, VPN server has ip 192.168.99.5
VPN Client 1 - 192.168.99.6
VPN Client 2 - 192.168.99.7
I am able to ping 192.168.99.5 from both clients, and able to ping 192.168.99.6 and 192.168.99.7 from server via remote desktop. But I am not able to ping 192.168.99.7 from client 1 and 192.168.99.6 from client 2.
If I trace route from 192.168.99.6 to 192.168.99.7 - I can see that packets goes to server (192.168.99.5) and next hop - request timeout.
What else should I configure to allow network traffic between VPN clients?

Hi,
To better analyze this issue, would you please post the routing tables on the two VPN clients? You can run "route print" at the command prompt to get the routing table.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Using Extreme in Bridge mode, can't see the DHCP clients if the D-Link router

I have an Airport Extreme attached to my DLink modem/router. I have configured the Airport Extreme in Bridge mode, and I was expecting all clients to show up in my D-Link router. Although the configuration works most of the time, I have been experience a few issues:
1. From time to time, computers attached (both Windows and/or Mac) complain about an IP address conflict. I can ignore the error and it works fine.
2. From time to time, I loose Internet connectivity, and I need to disconnect my computer and reconnect again to solve the issue. This is not necessarily linked to symptom #1
3. On my D-Link router/modem (which I only use to connect my Airport to my ISP), if I check the DHCP clients, I can see the Airport router connected and *some* of the wireless clients that connect through the Airport. The list changes quite randomly, and at times, I see the airport appearing twice with different IP addresses.
Any help configuring it "right" will be appreciated!
Alain

When the AirPort Extreme is in bridge mode, the AirPort Extreme is simply passing through the DHCP settings and services that are handled by the D-Link modem/router.
In other words, the D-Link device is in total charge of the DHCP services for devices on the network.
You might want to check with D-Link support to see if they have any recommended practices for configuing the modem/router when another router....the AirPort Extreme in this case....is being used in bridge mode on the network

True IP address for ARD remote client via IPObserver [newbie]

I have had success managing LAN clients via ARD, but now my situation is different.
I want to still be able to provide ARD support via a network address specific to a workstation from outside the LAN, and the IP address I have tried does not connect. I am deriving the address from the IP Observer utility that I had my client launch on their system. [it is not the obvious 192.168.1.xxx address from DHCP]. I have confirmed that the Sharing attributes are correct on the client system, although it might be a 2.2 version [running 3.1 admin]. Based on a test, I believe the IP Observer address is the internet IP location of the router [not the actual router LAN IP], not the client.
The IP address indicates that it is in the correct domain [Roadrunner, NYC], but the client-specific address is inaccurate. Is it because the client is setup through a DHCP router and switch? will they need a static IP? Can they somehow reveal their station-specific IP via an iChat connection log? should I try to address the client though a different port?
I am new to this extension of ARD, so bear with the obviousness of the query to some of you.
thx - steve

Hi, here is what you asked me for:
webvpn
enable inside
enable outside
csd image disk0:/securedesktop-asa-3.2.1.103-k9.pkg
svc image disk0:/anyconnect-win-2.2.0128-k9.pkg 3
svc enable
cache
max-object-size 5000
group-policy DfltGrpPolicy attributes
dns-server value X.X.X.X
dhcp-network-scope X.X.X.X
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
default-domain value XXXXXX
intercept-dhcp 255.255.255.XXX enable
nac-settings value DfltGrpPolicy-nac-framework-create
webvpn
url-list value Lan_Applications
svc keepalive none
svc dpd-interval client none
svc dpd-interval gateway none
svc ask enable default webvpn
customization value DfltCustomization
tunnel-group DefaultRAGroup general-attributes
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (outside) LOCAL
dhcp-server XXX.XXX.XXX.XXX
tunnel-group DefaultWEBVPNGroup general-attributes
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (outside) LOCAL
dhcp-server XXX.XXX.XXX.XXX
authorization-required
Best Regards,
Jeyriku

How to configure TMS landscape using three clients of same system?

Hi All,
I have to design a prototype for linking satellite systems to Solution Manager. To work on the Change Request Management module of Solution Manager.
Here, I need a Development - Quality - Production landscape to be configured to link it to Solution Manager, but I have only one system available to do this.
I have the clients 410, 420 and 430 in the system XYZ. Now, how do I simulate the three system landscape in STMS for the three clients mentioned above.
I tried using many attempts, but it is not working out. I could figure it out that this is possible by activating "extended transport control" parameter for each system, in STMS.
Also, there are some specific needs to configure this landscape for linking to Solution Manager, the comments are shown below:
"Transports are supported in the standard transport layer of each client. When you configure transport routes, note that only consolidation routes that are assigned to the standard transport layer of the relevant exporting client are taken into consideration. For each exporting client, exactly one target client and one target group are permitted.
We recommend that you assign exactly one development system to a production system, and that these two systems are connected by exactly one unique transport track.
If a development system and a production system are connected by more than one transport track, this may lead to inconsistencies within the transport distribution.
This type of transport configuration cannot be supported by Change Request Management, and may cause inconsistencies within the tools involved."
Please suggest me, as how to proceed to configure STMS for the same.
Thanks in advance.
Anil Santhapuri
Message was edited by: Anil Santhapuri

Hi Anil,
Can you please share how you could setup the 3 system landscape with diferent clients on one system using Target Groups?
Thanks,
Poorna

Telling if client is on N in 891W router

Similar Messages

Maybe you are looking for