Temperature measurement on real time from NI 9217

Hi,
I want to measure the temperature of a RTD, Pt100.
I am trying to plot temperature (axis Y) against real time (axis X). At the moment i have this "PT100_monitoring_test" attached but I would like to insert an external clock or something like that to measure the temperatura on real time.
Is this possible?
Thanks!
Attachments:
PT100_monitoring_test.vi ‏46 KB

Well,
using cDAQ you will not get more "real-time" than what you have.
You can increase the sampling rate, reduce the number of samples you acquire and optimize the postprocessing so that new samples appear on the screen faster, but at this moment you are already getting real-time data.
What do you want to achieve?
Mateusz Stokłosa
Applications Engineer
National Instruments

Similar Messages

Obtaining data in real-time from Microstrain wireless orientation sensor 3DM-GX2

Hello, all.
I am using
a wireless inertial sensor 3DM-GX2 with a USB Base Station from
Microstrain, and I want to read and use data values from it in LabView in real time.
But the problem is that I am not able to use the LabView examples or
the SDK provided by Microstrain either.
Link for SDK is here:
http://www.microstrain.com/updates/orientation-sdk.zip
I
have used the VI called "Read Accel and Ang Rate Serial.vi". I chose
the correct COM port for my sensor, that is COM3. When I run, I get an error in the node "VISA Read" (code -1073807339). Attached you can see a snapshot of this VI.
However,
I don't know if I have to use this VI because my sensor is a wireless
sensor (USB Base Station linked to 3DM-GX2 inertial sensor) and this
seems to be a program for reading from a serial sensor.
You can see in the link: http://forums.ni.com/ni/board/message?board.id=250&thread.id=42319&view=by_date_ascending&page=3; that there is another topic related to this, in which the discussion ended up with the users being able to read from the sensor, but I can't understand what they discussed there about communication protocols. I think I would need basic information so I could fix
my problem.
I am using LabView 8.6.
I hope you can help me. Thanks in advance.
Regards,
Francisco
Attachments:
Read Accel and Ang Rate Serial.vi Block Diagram.JPG ‏85 KB

Hi there, I had the same problems with this wireless sensor and the labview Vi's from the microstrain homepage. Please use the newest ones which are available from the microstrain homepage.http://www.microstrain.com/updates/labview-examples.zip The problem is in the "Read Accel and Ang Rate Wireless.vi". The node adress is missing. The node address are the last two digits of the
serial number (SN: 4200-1076 - node address=76) and is preset at the factory.
Here is a picture of the changed program.
I hope that may help you.
Kind Regards
Alex

Booting Into Real-Time From Hard Drive

Hello,
We have a system that is real-time compliant, as said so by the pceval software that NI has on their website, that will not boot into real-time OS from the hard drive. It can boot into RTOS with the floppy boot disk, but for some reason it can not do it from the hard drive alone. We made a format hard drive disk and run it and it says that it succussfully installs the files and tell us to reboot. When we do so the system has a short blinking line and just sits there, almost like the system is being haulted. We have formatted the hard drive many times using the format hard drive disk and we have even tried other floppies thinking that the disk was bad. We don't understand why it could boot into the RTOS from the floppy but not from the hard drive itself. The only thing I can think of is that the disk isn't writing the right MBR to the hard drive and it's not getting directions to boot. I have been working on this for quite some time, so any help would be greatly appreciated. Thank you.
Michael

We have actually figured it out, after many long days. You just install the RTOS like Labview says and make sure it is the first partition. Whether that is on another hard drive that is the master or if it is actually the first partition of the drive. We had two seperate drives and we were running Windows as the Master and the Labview RTOS as the slave. When we switched them it worked. Also, doing a long format (Not Quick Format) also fixed the situation. For a bootloader we are using GAG, THE GRAPHICAL BOOT MANAGER which can be found for free on google. Thank you for your help.
Michael

Synchronise time in array with the real time from computer

i need help in syrnchonising my array and the real time running in my computer
As stated in the text file attached,
12:32:30 AM 0.38 1.14
2nd column is wind speed, 3rd is gust speed.
i would like to display the wind speed in a gauge with the right values. like for example, at 12:32:30 AM OF REAL TIME, NOT BASED ON THE TEXT, i would like to display the 0.38m's of wind speed in the gauge.
how do i sync the time in array with the real-time?
i have attached a program i made so far. its abit messy. im still a student, need a lil help
Attachments:
Wind Speed and Gust Speed.txt ‏13 KB
Time and MaxMin.vi ‏18 KB

wali123 wrote:
wat u mean duplicate?
Don't continually post the same question over and over. If you have new information, add it to the original thread. Did you actually click the link under the word "duplicate"?
Chopping up a discussion about the same thing into several threads (like here is this thread, but also here and here) serves no useful purpose. It will not increase the chance of a good answer, in fact most people will simply ignore it.
Imagine if everybody else would post like you! Every discussion would be if three different places and we would have three times more threads.
LabVIEW Champion . Do more with less code and in less time .

Tax Audit file (Taxware) is updated real-time from SAP

This is an issue when there are server issues, disaster recover, or any connection issues. I do not see a way in RFYTXDISPLAY to control the update. Does anyone know how to make it so that the updates to external tax audit file is done in batch instead of real-time?

What release of SAP are you on? In some older releases, SAP provided update programs to do what you ask. If SAP is down, there are no transactions and no taxes to update. If Taxware is down, the updates are queued in SMQ1. You can, once Taxware is up, release all the updates.

How to populate the address field in real time from backend?

Hi Guys,
I want to populate the address field in srm portal when creating Shopping Cart. I got the data by using some BADI functions. Now the problem is I am not getting the structure/table where I should add that address so that it can reflect in the address field of shopping cart.
Can anyone help me out?
Regards,
Virendra Kedia

Joe - Work backwards from the value generated during the execution of the trigger. You have the value there so you could save it into a package variable right then (create a package with a variable and assign the value to the variable). Then create a process on the page (after the DML process) to assign the value of your package variable to a page item. Then in the branch back to page 1, pass the item. (Or without messing with the branch, the process could simply assign the package variable directly the the page 1 item -- :P1_ITEM := my_package.my_var; ).
An alternative would be to use the "returning into" feature of DML to capture the PK of the created record into an item. Then the next page process could use the PK to fetch the new row and get the dbname value for passing to page 1.
Another option would be to update session state directly in the trigger.
Scott

I would like to see the time in a waveform graph (real-time)

i need the x-axis of the waveform graph to show real time (from the computer clock). I have made a program with all the example. He read and log data when the chosen time has elapsed. the program work's well...but i dont't know why the x-axis blink every time he draw a point
i can see two x-axis in the same time.
i give you a picture of one of a part of my program, i hope someone can help me
Attachments:
my_software.JPG ‏128 KB

Hi,
I tried to reproduce what you were getting by building a simple VI but I havent had much luck (I have attached the VI).
Could you post your code so that I can take a look at it?
Feroz P
National Instruments
Attachments:
Graph.vi ‏39 KB

ABAP interface in real time

Dear all,
Hereafter is my scenario;
My customer after sales system works on AS400. Assuming that I would manage spare parts (required for after sales) inventory, including goods entry, goods issue as well as the company financial accounting in SAP, I have to interface the two system.
From SAP to AS400: (flow1) Master files + (flow2) goods entry
From AS400 to SAP: (flow3) AR postings, (flow4) goods consumption
Then my two systems will be in line in terms of referential data (flow1), stock movement (flow2 + flow4), invoicing (flow3).
1) My question is to know what would be the best way to flow2 knowing that stock movement following a goods entry (done in SAP) should be visible in real time from AS400?
2) Regarding other flows, no need for real time. So I guess flat file should be ok. However, would master data for instance sent from SAP to AS400 require a mapping table in order to be properly integrated in AS400?
Regards.

Real Time doesn't mean always fast. It depends on your application requirements.
Anyway, don't think too much about Real Time in Windows. If it's possible, try to do all "time critical" operations in Matlab and after that pull data with LV.

How can I find the minimum in real time

I 'am doing some type of sensing mechanism. I that the data is step count versus intensity. So I want to record the minimum in real time from. Please kindly help

Hi perumpadapu,
you should have learned by now to provide some meaningful example (data)…
There are functions to detect minima: ArrayMinMax, "smaller than" comparison, PtByPtArrayMinMax, MinMax comparison, ...
It all depends on your data!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Can I use Labview real time with PCI 6013?

How much does Labview real time cost?
Do i need to have some additional hardware to use labview real time with PCI 6013?

You can not use the PCI-6013 board with LabVIEW Real-Time.
We offer three platforms for LabVIEW Real-time. PXI embedded controllers, 7030 data-acquisition plug-in boards (7030/xxxx) and FieldPoint. For more information on these options go to www.ni.com/products and then choose Real-Time from the menu on the left. There are PCI versions of the 7030 boards. Each 7030 board has a data-acquistion board attached to it (6030E, 6040E or 6533). When you embed a LabVIEW Real-Time program on the 7030 you will be able to access the daughter board. You can not access other boards from the embedded program. If you want to use several daq cards in your real-time system I would recommend a PXI chassi and PXI daq boards.

Process speed necessary for real time livetype & Motion

Does anybody remember the minimum processor speed necessary to
run LIVETYPE and MOTION from WITHIN FCP5...not as seperate apps?
The online spec sheets indicate the speeds necessary for running as seperate apps,
but not for real time from withing FCP5...at least, not the ones I can find.
Thanks.

Where did you encounter the promise of real time in FCP?
Can't be done AFAIK.
Even if possible, you'd only get a few misleading preview frames.
We've got our new biga$$ Macs arriving in a few weeks. I'll let ya know if anything happens real time in FCP.
bogiesan

Read CPU temperature of Desktop PC running LabVIEW Real-Time

Is it possilbe to read the CPU temperature of a Desktop PC running LabVIEW Real-Time? I found an older example that allows to read the temperature of PXI systems (http://www.ni.com/example/29538/en/). Is there a possibility for Desktop Real-Time Machines as well?
Regards,
Steffen

Hi this is heavily dependent from your specific Hardware. Which PC or more specific which main board do you use?
I found several examples in the NI forum that try to access the CPU data.
I’m using a Dell machine and both temperature VI’s are not working for me.
Hope you have more luck.
Attachments:
Temperatur_der_CPU.vi ‏13 KB
WMI_GetTemperatureProbe[1].vi ‏26 KB
WMI_Win32procesor[1].vi ‏41 KB

How can I extract the data from a Real-time Execution Trace ".log" file?

I would like to get the data for the traces from the Real-time Execution Trace toolkit ".log" file to read in Excel and generate a report.

Hi Chuck,
Have you tried reading it into a text or binary file first and then generating a report using the Report Generation VIs?
Ipshita C.
National Instruments
Applications Engineer

How can I generate a real-time highchart from my database data?

I have looked several links; however, I couldn't find a working demo showing how to implement a highchart using data from a database.
Objective: I want to generate a real time highchart line graph getting data from my database. What I want is very similar to the
HighChart Demo which provides a real-time highchart with randomly generated values. It is also similar by X-axis and Y-axis, for I want my x-axis to be "Time" (I have a DateTime column in my database) and y-axis to be an integer (I have
a variable for that as well in my database).
Please I need help in sending the model data to my razor view.
Note that I am already using SignalR to display a realtime table. I also want to know if it can be used to automatically update the highchart as well.
Below is the code snippet of my script in the view. I have used the code provided in
HighChart Demo link for generating the highchart. Please tell me where should I apply the changes on my code.
@section Scripts{
<script src="~/Scripts/jquery.signalR-2.2.0.js"></script>

<script src="~/SignalR/Hubs"></script>
<script type="text/javascript">
$(document).ready(function () {
// Declare a proxy to reference the hub.
var notifications = $.connection.dataHub;
//debugger;
// Create a function that the hub can call to broadcast messages.
notifications.client.updateMessages = function () {
getAllMessages()
// Start the connection.
$.connection.hub.start().done(function () {
alert("connection started")
getAllMessages();
}).fail(function (e) {
alert(e);
//Highchart
Highcharts.setOptions({
global: {
useUTC: false
//Fill chart
$('#container').highcharts({
chart: {
type: 'spline',
animation: Highcharts.svg, // don't animate in old IE
marginRight: 10,
events: {
load: function () {
// set up the updating of the chart each second
var series = this.series[0];
setInterval(function () {
var x = (new Date()).getTime(), // current time
y = Math.random();
series.addPoint([x, y], true, true);
}, 1000);//300000
title: {
text: 'Live random data'
xAxis: {
type: 'datetime',
tickPixelInterval: 150
yAxis: {
title: {
text: 'Value'
plotLines: [{
value: 0,
width: 1,
color: '#808080'
tooltip: {
formatter: function () {
return '<b>' + this.series.name + '</b><br/>' +
Highcharts.dateFormat('%Y-%m-%d %H:%M:%S', this.x) + '<br/>' +
Highcharts.numberFormat(this.y, 2);
legend: {
enabled: false
exporting: {
enabled: false
series: [{
name: 'Random data',
data: (function () {
// generate an array of random data
var data = [],
time = (new Date()).getTime(),
i;
for (i = -19; i <= 0; i += 1) {
data.push({
x: time + i * 1000,
y: Math.random()
return data;
function getAllMessages() {
var tbl = $('#messagesTable');
var data = @Html.Raw(JsonConvert.SerializeObject(this.Model))
$.ajax({
url: '/nurse/GetMessages',
data: {
id: data.id,
contentType: 'application/html ; charset:utf-8',
type: 'GET',
dataType: 'html'
}).success(function (result) {
tbl.empty().append(result);
$("#g_table").dataTable();
}).error(function (e) {
alert(e);
</script>

Hi Sihem,
Thank you for contacting National Instruments. Using the LabVIEW Real-Time module, you can do development without actually having a target. While viewing the project explorer window, you can do the following steps:
Right click on the project
Select New >> Targets and Devices
Select the "New Target or Device" radio button
Select the target you would like to develop on.Information about the LabVIEW Real-Time Module can be found here.
Regards,
Kevin H
National Instruments
WSN/Wireless DAQ Product Support Engineer

How to copy data from a Input query to real time Infocube

Hi All, I need some help on IP related stuff. The details are as below:
I am using two real time infocubes and one Multiprovider on them.
First Infocube u2018PRODUCTu2019 with the following Objects:
Product Group ,Product,Region ,Fiscal Year , Fiscal Year Varient ,0currency
Gross Sales
Second Infocube u2018C_PRODUCT u2018 with the following Objects:
Product Group ,Product,Region ,Fiscal Year , Fiscal Year Varient ,0currency
Gross Sales and Forecast Sales
( u2018Forecast Salesu2019 in the extra object in the second Infocube. Remaining objects are same in the both the cubes)
First Infocube u2018Productu2019 has data but the second cube does not have any data.
I have created a Multiprovider ZMulti and in that I have included these two cubes. On this Multi Provider, I have created a Aggrigation Level(The details of the aggregation level is provided in the next page).
On this Aggrigation level I have built a Input Query by which I run the report.
(In the Rows area, I have taken Product Group, Product, Region and Fical year.
In the Key Figure section, I have taken Gross Sales and Forecast Sales( which is part of the second Infocube C_Product). These two Key Figures are made Input as Input ready. And the Query is Input ready query. In the Filter, I have taken Fiscal Year Variant. )
Data available in the first cube and no data currently in the second cube. Now executed the report and report displayed information from the first cube.
EX:
Product     Product     Region          Year     Gross Sales     Forecast Sales
Group
PG01           Beer           North           2008           10000           u2026u2026u2026
PG01           Beer          South          2008          20000           u2026u2026u2026
PG01          Beer          East          2008          15000           u2026u2026u2026
The second column is empty and there is no data for the Forecast sales Key Figure in the column.
Things look OK till the above.
Now based on the Gross Sales, I am entering forecast Sales values and I need to save the entire record to the second cube.
For this in the report, I have given the Forecast sales values in the second column and right clicked the mouse and form the menu which I got, selected the u2018SAVEu2019 Option to save the data. For some time, I can see u2018Processingu2019 message and later values at u2018Forecast Salesu2019 are disappearing.
Data is not saving to the cube second cube.
====================================================
Am I missing any thing?
In the Query, Do I need to provide InfoProvider and restrict it to specific value?
In the query, Do I need to include, 0currency object?
Could you please guide me on this?
=============================================
Details of the Aggrigation level.
            I have created an Aggrigation Level ZAL_Prod on MultiProvider.
            Selected all the objects and activated.
            In the Filter, I have taken 0Fiscal Year Variant and saved it.

Restrict Forecast sales to the Plan cube in the Query.
that should fix it.

Temperatur​e measuremen​t on real time from NI 9217

Similar Messages

Maybe you are looking for

Temperature measurement on real time from NI 9217