The spanning-tree add strange value when I create new Vlans
Hi,
On all switchs access, the spanning-tree add strange value when I create new Vlans from Distrib Layer,
and no association is created with any interface with spanning-tree vlan 700, see below in this exemple,
until I reboot the switch.
somebody already saw this values ?
DSFDS112#sh span sum
Switch is in rapid-pvst mode
Root bridge for: none
EtherChannel misconfig guard is enabled
Extended system ID is enabled
Portfast Default is disabled
PortFast BPDU Guard Default is disabled
Portfast BPDU Filter Default is disabled
Loopguard Default is enabled
UplinkFast is disabled
Stack port is StackPort1
BackboneFast is disabled
Configured Pathcost method used is long
Name Blocking Listening Learning Forwarding STP Active
VLAN0001 0 0 0 3 3
VLAN0002 0 0 0 22 22
VLAN0006 0 0 0 3 3
VLAN0007 0 0 0 8 8
VLAN0009 0 0 0 4 4
VLAN0010 0 0 0 3 3
VLAN0011 0 0 0 3 3
VLAN0012 0 0 0 3 3
VLAN0013 0 0 0 3 3
VLAN0090 0 0 0 15 15
VLAN0109 0 0 0 3 3
VLAN0200 0 0 0 4 4
VLAN0300 0 0 0 26 26
VLAN0302 0 0 0 4 4
VLAN0700 - 253 -1872756560 2087191206 -1872756549 2080375982
VLAN0702 - 253 -1872756560 2087191206 -1872756549 2080375982
VLAN0704 0 0 0 4 4
VLAN0710 - 253 -1872756560 2087191206 -1872756549 2080375982
VLAN0816 0 0 0 3 3
VLAN0820 0 0 0 3 3
20 vlans - 759 -1323302384 1966606322 -1323302237 1946160764
DSFDS112#sh span vlan 700
VLAN0700
Spanning tree enabled protocol rstp
Root ID Priority 4796
Address 0008.e3ff.fcbc
Cost 10000
Port 608 (Port-channel1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 62140 (priority 61440 sys-id-ext 700)
Address 885a.9213.6880
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 sec
Interface Role Sts Cost Prio.Nbr Type
Po1 Root FWD 10000 128.608 P2p
DSFDS112#sh run int Gi1/0/25
Building configuration...
Current configuration : 194 bytes
interface GigabitEthernet1/0/25
description Station12
switchport access vlan 700
switchport mode access
end
DSFDS112#sh span interface Gi1/0/25
no spanning tree info available for GigabitEthernet1/0/25
DSFDS112#sh int status interface Gi1/0/25
Port Name Status Vlan Duplex Speed Type
Gi1/0/25 Station12 connected 700 full 100 10/100/1000BaseTX
Thanks for your help,
Regards.
Venki,
The ORA-00942 is okay because there is no existing object. But what stuck me is the ORA-01921 error which may indicate that this might not be a new database.
CREATE ROLE exp_full_database
ERROR at line 1:
ORA-01921: role name 'EXP_FULL_DATABASE' conflicts with another user or role name
CREATE ROLE imp_full_database
ERROR at line 1:
ORA-01921: role name 'IMP_FULL_DATABASE' conflicts with another user or role name
Are there any existing databases on this server? Have you tried to create it on other machine?I searched on Metalink too and found Doc ID: 237486.1 ORA-29807 Signalled While Creating Database using DBCA which say that eroror could be ignored. You may want to review that as well.
Ittichai
Similar Messages
-
What is the command to check the changes in the spanning-tree topology?
What is the command to check the changes in the spanning-tree topology?
Hi,
Few commands which would help are:
1- Show spanning-tree detail
2-show spanning-tree detail | in ieee|from|occur|is exec >> This will give from were the changes occuring- Ex:
C6K1#show spanning-tree detail | in ieee|from|occur|is exec
VLAN0001 is executing the rstp compatible Spanning Tree protocol
Number of topology changes 9536 last change occurred 00:00:29 ago
from GigabitEthernet4/6
3- show spanning-tree active *& show spanning-tree root >> Will give you the root information.
4- show spanning-tree inconsistentports >> If there are any port which are inconsistent state due to STP features.
STP running MST:
===============
show spanning-tree mst configuration >> Need to check and match the same outputs with the other switches running in the same MST domain/region.
show spanning-tree mst detail
show spanning-tree mst <name of the region>
Debug on STP:
============
debug spanning-tree events/bpdu >> would be good but to be run with more cautious.
HTH
Inayath
*Plz rate if this info is usefull. -
I have downloaded the Firefox Sync add on but when I select "add a device" it launces a help page which tells me to click "add a device" which is an endless circle!
Any advice appreciatedSorry about that. The help pages have been updated for the new "Add a device" process in Firefox 4, but the add-on for Firefox 3.6 is still using an older, different process.
You can download the Firefox 4 release candidate here and use the new "easy setup" process described in the help pages: http://firefox.com/rc
Or if you prefer to stick with Firefox 3.6, then instead of clicking "Add a device" on your computer, press the "Connect" button on your phone or other device, then click on "I am not near my computer..." and enter your email address, password, and sync key. (If you don't know your sync key, see [[Where can I find my Firefox Sync Key?]]) -
Why the host ports are also seen in the spanning-tree output ?
Why the host ports are also seen in the spanning-tree output ?
Switch1#show spann
VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 32769
Address 0000.0CA2.138B
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
Address 0000.0CA2.138B
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 20
Interface Role Sts Cost Prio.Nbr Type
Fa0/1 Desg FWD 19 128.1 P2p
Fa0/2 Desg FWD 19 128.2 P2p
Fa0/15 Desg FWD 19 128.15 P2p
interface FastEthernet0/15
description PC0 Interface
switchport mode access
spanning-tree portfast
interface FastEthernet0/16
I read somewhere that all the ports of a switch will participate in STP by default. Is there any way to remove the STP operation on host ports ?
Regards,
ChanduAll ports participate in Spanning Tree by default.
Spanning tree is there to block redundant L2 paths in order to prevent loops. All ports are capable of causing a loop so you would not want to turn spanning tree off, in fact I don't think you can switch it off on a per port basis. You can switch it off on a per vlan basis.
You are already using portfast which allows host ports to transition into a forwarding state without going through the listening and learning states of STP. If you switch off STP on a port, you risk the chance of a L2 loop.
https://supportforums.cisco.com/docs/DOC-5180 -
I have changed the email signature on my iPhone, when composing a new email the signature is there, however when I am replying to an email it is not, how can I make sure that the signature is at the end of every email I send?
Yes I know what you mean about it cluttering the thread and for personal emails it is better without the signature. However this relates to sending business emails from an iPhone so I need the signature present on every email.
I can't find anything in Settings so I was hoping someone may have some knowledge/information/experience regarding this problem. -
How to refresh the grid so that default values come on adding new row.
Hi Experts,
In alv grid while adding new row, i want some 2-3 column values to come by default from already existing row in grid.
i am getting new row in internal table with 2-3 default values and rest columns blank on adding new row in alv grid
but the entire row is coming blank, not able to get the default values in new row
how can i refresh the grid so that default values come on adding new row.
thanksHi Surabhi,
Use this in Interactive section even if you are doing simple ALV.
DATA:
lv_ref_grid TYPE REF TO cl_gui_alv_grid.
CLEAR : gv_tcode.
*-- to ensure that only new processed data is displayed
IF lv_ref_grid IS INITIAL.
CALL FUNCTION 'GET_GLOBALS_FROM_SLVC_FULLSCR'
IMPORTING
e_grid = lv_ref_grid.
ENDIF.
IF NOT lv_ref_grid IS INITIAL.
CALL METHOD lv_ref_grid->check_changed_data.
ENDIF.
THis will solve your problem.
Regards,
Vijay -
Project Server default groups when we create new project site
Hi,
When we create new project site in project server 2013 in site settings page some default groups are already present with some default permissions and some default members.
Interesting thing is that the members of these group are same when ever we create a new site.
Can you please help me understand, what these groups are, how they get created and how they are having some default members. Where are these members coming from.
Our project server is having project server permission mode.
Thanks,
Bhawna.I briefly searched the MSTechNet but was not able to find a succinct article on this point for 2013, if someone has that, can they pls share. However, if you read most of the articles under this area,
you get the idea.
http://technet.microsoft.com/en-us/library/fp161361(v=office.15).aspx
From 2010 this applies and is still "similar"
http://technet.microsoft.com/en-us/library/cc197668(v=office.14).aspx
In 2013, for every Project Site (connected SharePoint site as it is now called in 2013), 2 Site specific SharePoint security groups are created: "SiteProjectName Project Managers (Project Web App Synchronized)"
& "SiteProjectName Team Members (Project Web App Synchronized)".
And Web Administrators (Project Web App Synchronized) is also created.
In addition, the default SharePoint groups for: Site Members, Site Owners, Site Visitors are present but remain empty.
Project Server controls the creation of these groups and the membership. The membership is a "formula" that goes something like this: If the user is the Project Owner then put them in the PM group.
If the user is a PWA Administrator, then put them in the Administrators group. If the user is a team member on the project, then put them in the Team Members group. There are other factors like RBS that are used in the formula.
Reading the descriptions of the groups reveals that for Project Managers =
Users who have Published this project or who have Save Project Permission in PWA.
For Team Members = Users who have assignments in this project in PWA.
I believe these are the old 2010 descriptions and actually Team Members = anyone who is part of the Build Team even if no assignments.
Further complicating matters is that if you are a site collection admin, you will see all the groups, for PWA and for all the project site (b/c you are actually seeing the site collection groups).
But only the ones mentioned above apply specifically to this project site.
Hope this sheds some light on the topic,
Thanks, Eric S. Pcubed -
Alert and second alert when you create new event
problem with alert and second alert when you create new event on calendar. but only in russian iphone language!
this problem starts iOS 7 up to the present time iOS 8.1.1. this problem has been seen on iPhone 4,iphone 4s,iphone 5, iphone 5s,iphone 6,iphone6+Settings>General>Reset> Reset all Content and Settings
standard fixing such bugs, but not in this time -
I have a problem with my iPad 1 . When I create new g Id , I have a Clam requied update iOS last vesion while this version is 5.11 . Help me. Thanks
Before I update my iOS auto is 5.11 . Apter I reset my iPad and crease new Id then error Appear . I can not fix it . Thanks your support
-
Why the contract data is not modifiable when I create a order
I have already assigned the Contract Profile to a sale order type in the Sale order type definition, and the contract profile has been set correct.
When I create a order by this order type (Ive tried both copy and create a new order type), I cant modify the contract data from Goto>Header>Contract data,
what is the reason, how can I reset it, appreciate for your help, Thank you!hi,
contract is an agreemet made following which we create a sales order called a release order. so, we only refer that and release whats being agreed as part of contract.
Let us look at this situation from a business point of view. so once you create a contract profile and assign to sales order, we cant modify it at the sales order level.
Hope it helps. Pl reward if useful.
Thanks,
Sadhu Kishore -
I am a rookie. This worked on previous pics but I apparently have clicked something I shouldn't have. Thanks for any help.
The problem with Actions is that as a new user, you are not going to know what steps are happening when the Action runs. The action could be deleting the background layer, for instance. Is the action one that came with Photoshop? If you sourced it from somewhere else, can you give us a link?
There is also some ambiguity in the language you use. Not your fault. But when you say 'create new layer from background' to me that probably means you are copying the background layer. If that is not the case, could you give a more detailed description of the steps you are taking?
Do you know how to upload a screen shot? If you are using Windows 7 or 8, you can use the Snipping tool to drag across your image and layer panel. Save the image, and upload to this thread using the little camera icon. -
How do I make it so my client can edit Links in business catalyst when they create new pages?
Okay so essentially I have built a site in Muse uploaded to business catalyst and I've setup a site template so that the client can create new pages as each new course arrives, but how do I get the link from the homepage to link to the new page? basically I need the link to be editable.
What would be ideal is a kind of portfolio layout where there is a thumbnail and a new page but for my client to be able to add a new project adn it would create a thumbnail on the homepage and a new page that he can edit. Does anyone know of something like that possible in Business catalyst?Hi
Editing with Business Catalyst only works with image or text editing , we cannot add new page or page items using in browser editing.
However, you can manage the site from BC end when your client and login to admin and add pages, modify etc, but if you re-publish the site from Muse then then changes will be overwritten.
Thanks,
Sanjit -
When ever create new version specified User should get intimation Mail
Hi,
My requirement is when ever user create new DIR version, system should send some intimation Mail to specified user.
If it's not possible in standard system, Pls let me know it is possible through development or not.
Thanks & Regards,
SunnyDoes the specific user, u want to send the mail, keeps changing?
At the time of creation of a DIR if reqd value is maintained in User Responsible then he'll get the mail in his SAP Inbox stating "The Document for which u r responsible has been created/modified".
For this certain linkages in workflow needs to be activated.
If you want to send the mail in specific format with some more details, then u may use messages functionality of DMS in which mails are sent based on Document Type & Status combination.
Another option is using workflow. For this u need to define a simple workflow task which can be triggered based on status. you need to maintain this task in Status settings.
Points Appreciated. -
When to create new authorization objects
Hi Experts,
I am learning SAP Security.
I have one question , what is the necessity of creating new authroization field and object , when SAP gives a huge list of objects /fields.
Is there any reason behind like, whenever a customised transaction is created, a new authorization object or filed has to be created?
Regards,
RekharajTrick is to find not only a standard authorization object with the same field you are looking for, but an object already assigned to the users with those roles with the same semantic for all it's fields - so that you can simply reuse the existing concept which is also assigned to the sets of users.
Often you will find "base" function modules and classes you can use to do all that work for you. Just call them at the correct location in the code and dont forget to check the return code and react to it.
If you use BAPI APIs to access or process data, then many of them make these same semantically correct checks "out of the box".
Cheers,
Julius -
Access Denied when Exporting, Creating new folder.
My normal workflow on some occasions is that I work on images then making a selection, I will export then to a folder on my desktop. I normally hit the Export and on the pop up I click on create new folder and export the images to the folder.
Since the new update, when I try to create a folder it gives me Access Denied. If I create the folder first, there is no problem.Hi,
I would like to suggest you run the following commands with elevated privilege.
takeown /f {Folder Path}
cacls { Folder Path} /G administrators:F
Note: please replace {Folder Path} with the real folder path.
After that, please try to delete the folder again.
Does it work?
Regards,
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Maybe you are looking for
-
New Depreciation to start from Mar (not Jan) after change of useful life
Hi Does anyoe has any solution or will there be changes to SAP B1's Fixed Asset? Let me explain the full scenario as below: 1) Customer has Fixed Assest which has useful life of 25 years, i.e. 300 months. 2) The assets has been depreciated for a few
-
Siri not working while connected to Audi AMI
it turns out that I cannot fully use the features of my iPhone while connected to a certified car audio system (Audi Ami). env: iOS (10a403), iPhone 4S ,audi q5 , ami hw h07,sw 0350, Bluetooth Nokia bh-202 issue: iphone connected to car through cable
-
My applet won't print properly
I wrote an applet that draws a line graph based on parameters I feed it through <PARAM> tags. Those tages are written dynamically with Cold Fusion. It works perfectly, but what good is a graph if you can't have a copy of it? When I try to print the p
-
Enterprise Edition of Nokia PC Suite
Hey, I wud like 2 share this one http://europe.nokia.com/find-products/nokia-for-business/managing Glad news for Enterprise Users If my post helped you, click on Kudos button and if my solution provided is opt 2 u, accpt my solution
-
Is the iTunes Store Down - APPLE PLEASE RESPOND
Is the iTunes Store Down - APPLE PLEASE RESPOND