Time based mode runs 4 hours before time set

time based modes are running 4 hours early...
The mode was set for 6:00 pm, ran at 2:00 pm.
changed it to 8:00 pm it then ran at 4:00 pm
when creating the mode it said that EST after the begin time, so it knows the correct time zone that I am in
Bill T

Paul,
Can you elaborate on where you applied the configuration. I have a scenario where Rightfax sends the call to CUCM via an H323 trunk, then CUCM sends the call to the PSTN Gateway and then out to the PSTN. I am experiencing the same issue where the call disconnects before the destination fax answers if it is set to ring 3 or 4 times before answering.
I'm not sure that I understand what you mean by splitting the incoming and outgoing dialpeer. I have the following dialpeer to match and route my outbound number to the PSTN.
dial-peer voice 92 pots
translation-profile incoming PREFIX-9
translation-profile outgoing CALLERID
destination-pattern 91[2-9]..[2-9]......
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/0:23
forward-digits 11
I appreciate any help you can provide.

Similar Messages

Time an Hour Before

Hi Gurus,
This may a trivial question, but I want to know time exactly an hour before.
Please help.

RK Veluvali wrote:
This may a trivial question, but I want to know time exactly an hour before.Oracle date arithmetic uses day as a unit of measure. Threfore one hour is 1/24:
SQL> select to_char(sysdate,'HH24:MI:SS'),to_char(sysdate - 1 / 24,'HH24:MI:SS') from dual
2 /
TO_CHAR( TO_CHAR(
09:12:26 08:12:26
SQL> SY.

Having very difficult time setting up and running time capsule and airport

I am having a very difficult time setting up and running airport express and time capsule. My time machine is not being recognized by my mac. The amber light keeps blinking. I'm ready to stsrt over.

#3 for itunes streaming. I reset the base station and eventually was able to get the backup working and now my green light is on. Next I'd like to be able to play itunes using Airport Express and have connected to my stereo receiver in another room.
AirPort Express Base Station (AX) - iTunes Setup
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <existing TC's wireless network>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
Verify Password: <re-enter the existing wireless network password>
AirPort Utility > Select the AX > Manual Setup >Music
Enable AirTunes (checked)
iTunes Speaker Name: <enter desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings to the AX

Hello! please change the time setting for Russia in the hour ahead. Unas in the country while now and there is one year, or winter.

Hello! please change the time setting for Russia in the hour ahead. Unas in the country while now and there is one year, or winter.

It is November 9, and the problem still persists. The Time in Russia is reported by OS X as one hour behind... Apple, Please fix this problem.

HT4993 When I send Outlook invites to my iPhone (via email) the appointments appear 3 hours earlier? The time setting appears to be EST which is accurate so I can't figure out why the appointments don't appear in real time. Thanks for your help, Ellen

When I send Outlook invites to my iPhone (via email) the appointments appear 3 hours earlier? The time setting appears to be EST which is accurate so I can't figure out why the appointments don't appear in real time. Thanks for your help, Ellen

1) The best way to relocate the iTunes library folder is to move the entire iTunes folder with all subfolders to the new path, then press and hold down shift as start iTunes and keep holding until prompted to choose a library, then browse to the relocated folder and open the file iTunes Library.itl inside it.
If you've done something different then provide some more details about what is where and I should be able to help.
2) Purchases on the device should automatically transfer to a Purchased on <DeviceName> playlist, but it my depend a bit on whether automatic iCloud downloads are enabled. If there is a cloudy link then the transfer might not happen. You can use File > Devices > Transfer Purchases. In iTunes you should also check out iTunes Store > Quick Links > Purchased > Music > Not on this computer.
3) Backup the device, then immediately restore it. In some cases you need to add a restore as new device into that equation. Obbviously not to be attempted until you're sure all your media is in your library. See Recover your iTunes library from your iPod or iOS device should it be needed.
4) I believe there is complimentary 1 incident 90-day support with hardware purchases, but no free software support for iTunes itself. AppleCare gets you a different level of support.
tt2

Why is the purge command running every hour, and freezing my system?

I noticed over the past several days that my mac pro will freeze for several seconds (clock stops, mouse/keyboard don't work. completely frozen) every hour, to the minute.
I've tracked it down to the "purge" command, which is causing the problem. But, I can't find where it's being called. Any hints where I might look to find the cause?
I don't believe this was happening a few days ago. I have installed all software updates.
I'm running 10.7.5 on a 2x2.66Ghz 6-core mac pro.
Thanks!

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then copy it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click the line of text below to select it:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
Copy the selected text to the Clipboard by pressing the key combination command-C. Then click anywhere in the Terminal window and paste (command-V). Post the lines of output (if any) that appear below what you just entered. You can do that by copying and pasting as well. Omit the final line ending in “$”. No typing is involved in this step.
Step 2
Repeat with this line:
sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}'
This time you'll be prompted for your login password, which you do have to type. It won't be displayed when you type it. Type it carefully and then press return. You may get a one-time warning to be careful. Heed that warning, but don't post it. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
Step 4
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, steps 1-5 are all copy-and-paste — no typing, except your password. Also remember to post the output.
You can then quit Terminal.

Email a month, a week, then 48 hours before event starts

I am having trouble figuring out the logic for this workflow request.
A calendar event is added with an "End Date" E-mail 30 days before "End Date" then E-mail 7 days before and then 48 hours before.
I am running into issues with knowing what to put first / or in front.
I want to set it so that if an item is added say 4 days from "End Date" that they won't get 30 days and 7 days E-mails, and it will "pause" until 48 hours before the End Date. I don't HAVE to Pause, just trying to figure out how
to get the workflow...to work.
I setup the 7 day stage and 48 hours stage to be the same as the 31 day stage (in the graphic below)
I have conditions for "Monday" and "Tuesday" as they want M-F E-mails, not counting the weekends, so I am "adding" more time if they select a checkbox for "On a Monday" or "On a Tuesday" when they add an
item.
I have this setup for manual, if item added, or changed.
Thank you!

Hi,
From your description, my understanding is that you are
confused about Workflow logic.
Based on my understanding, you want to your workflow could send mail as below:
If Today <= End-Date-31Days, then pause workflow until End-Date-31Days to send 30 days before email.
If End-Date-31Days < Today <= End-Date-7Days, then pause workflow until End-Date-7Days to send 7 days before email.
If End-Date-7Days < Today <= End-Date-48Hours, then pause workflow until End-Date-48Hours to send 2 days before email.
If my understanding is correct, you could refer to the screenshot below to set the conditions.(in my case, End-Date-31 equals End-Date-31Days, End-Date-7 equals End-Date-7Days, and End-Date-2 equals End-Date-48Hours)
You could refer to this article:
https://kmlsp.wordpress.com/2013/03/06/more-on-calendar-reminder-4-steps-to-create-reminder-workflow-in-sharepoint-calendar/.
If I misunderstand your requirement, please let me know.
Best Regards,
Vincent Han
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

IMac Harware Test runs for hours, repairpermission too

My iMac G5 started having failures last year already. So I first ran Disk Warrior and everything turned out well for a while. But now, the system started showing the endless rotating whell when booting, and I could not do an Archive and Install. So I diagnosed a HD failure and bought a new HD.
I reinstalled everything via Carbon Copy Cloner and did and Archive and Install. But obviously the permissions were wrong and Disk Util took ages trying to repait them. So I decided to boot in Single User Mode and tried to run Applejack wich also seemed to step on the spot after finding some "bad Alloc[157]...etc". So I threw in Apple Hardwae Test and ran a full checkup and as it turns out, it gets stuck when checking the RAM, so I stopped it after 1 hour.
Does anybody have a clue of what might be wrong? How shall I determine what is rong when Hardware Test stops in the middle? Is it the RAM? How should I find out?
mat

Hello,
You re absolutely right. I did too many things at the
same time.
Yes, repairs and trouble-shooting need to be done systematically. And, it needs to be done with tools appropriate to the task.
Using one tool to do this, and then another tool to fix the first tools mistakes, and then jumping to another one just doesn't work well.
I finally reinstalled the system and tomorrow, while
I'm at work,
Yes, that will be the way to go.
You should consider that while you are at work, the system will be sitting there completed. So, if your fans run full speed while in the diagnostic test (I cannot remember for sure if they did or not on my system), then they will continue to do so until you come back.
I don't know if I'd leave the computer there for 8 hours with fans at full speed and the screen unmoving on maximum brightness. That just doesn't sound ideal to me.
I think perhaps I'd demonstrate exactly what you want done to your wife (or someone else if someone else is home), and request them to do that for you to get the machine up and running for you about 2 and a half hours before you get home.
I'll have Hardware Test running at home.
I was just quite exasperated because Hardware Test
said it would take about 15 Min, so after an hour, I
thought it was stuck.
That's understandable.
I promise to be a goob boy now and stop thinking my
Mac was a box of Lego where I can unbuild and rebuild
everything like I please.
Yes. Computers don't like that
Let us know how it works out.

Discoverer report running for hours

Hi,
One of the custom discoverer report (based on custom SQL) is running for hours.
When U ran the query for the respective folder, the results were returned in few seconds.
Hence, data size is not an issue. How can I identify the cause and solve it?
Thanks,
Kamath.

Hello
If you dont need to run the report urgently then you can always schedule it to run the background till it is finished.
First log into desktop. Select tools > options > query governor tab. Make sure only radio button named "Never" is ticked. Leave all other options empty / not ticked. Click OK when ur done.
Then go to File > Manage Workbooks > Scheduling Manager > Schedule.... button then choose either My Computer or Database depending on where your report is stored. Scroll down and find your report. Enter a time and date that you want to start running the report. When you are done click Finish button. Normally the report would run for an hour or till it is complete. But it won't bomb out.
After 2 hours or even the next morning go to File > Manage workbooks > then look for your report > if it has run successfully then the status column would return something positive like "completed successfully". just double click your report and your are done....
It works for me if i need to run one of my reports. but that is only if your not in a rush to run your report
Hope it helps
Edited by: iandekoker on Jun 11, 2009 12:48 PM
Edited by: iandekoker on Jun 11, 2009 12:49 PM

Active Users Request is still running for hours in Release 12

Hi Friends,
Today I have installed the Release 12 in the Red Hat AS 4.0. Installation was successfull.
All the Concurrent Managers are up and running.
I have run some requests in the Paybles, Receivable..
Requests are running for hours..all are standard reports...
even
Active Users Request is running for hours..there is no end...
Friends...
How to trouble shoot it???????????
Please give me advice...
Regards,
Subbu

Hi,
Thanks for the reply......
Is this a fresh installation? If so, what version? Which OS?
Ans: Yes This is a fresh installation...After InstallationAll concurrent Managers are up and running...
Was this working properly before? If so, what modifications have you done?
Ans: As this is a fresh installation. This is first time to run the requests. After installation, when i run the requests, I got error like libmawt.so is not opened. I have given libmawt.so file path in the LD_LIBRARY_PATH. After setting libmawt.so in the LD_LIBRARY_PATH. this time I did not before error. but request is running for hours..there is no end.
Have you tried to recover the CM from OAM?
Ans: ya, I tried, but not helpful.
Tracing should be helpful, did you try to run CM Diagnostics test?
If you shutdown the CM and submit the request, what do you get?
Ans: I got status as Inactive and no manager
This is the error in the my manager log file
Routine AFPCMT encountered an ORACLE error. ORA-01012: not logged on.
Review your error messages for the cause of the error. (=<POINTER>)
_ 2 _
Routine AFPCSQ encountered an ORACLE error. ORA-01005: null password
given; logon denied
I tried to relink FND executables using adadmin. But it did not sovle out my problem. As this is solution in metalink for above error.
My Version is : Release 12 on Red Hat AS 4.0
Regards,
Subbu

IPhone staying in restore mode for an hour? Updating to 4.2 from 4.1.2.

My iphone 3GS has been staying in the restore loading screen for a good hour now and this is the 8th time i have had to restart the entire process. i have disconnected the cable, restarted computer and restarted the phone. now my phone is stuck in DFU mode because it cannot complete the restore. i cannot get iTunes to complete the restore and sometimes i wait overnight for the restore to be completed.

I'm in similar situation.....
My home set up is
1office PC (hard wired to sky broadband) 1 working laptop and my iphone 3g ( via wifi to braodband) i regularly doc and sync my phone with the office PC but not done since begin dec before I updated PC and laptop software.
I also have linked to ITunes 1x ipod nano 2nd gen (daughters) and 1 x Ipod touch 3rd gen (other daughter)
On thurs 30th decided to sync with PC but as it bombed out updated the ipod nano this was left overnight.... it sorted out the music download one happy daughter with xmas present (recycling my old one I found in cupboard)
Have been downloading 12 days of christmas so when tried to update on Fri 31st it said it would take 14 mins so i walked away ... forgot and returned to see it had not done it again after 3 hours!!! Meanwhile though I would get mobile me to sync correctly with PC after spending 6 hours updating my contacts 600 on the PC manually to get mobile me to be overwritten sucess. So I tried to update again this time said 19 mins then decided to restore.
After sussing how to transfer my downloaded items from 12day of christmas from phone I took the plunge to restore phone I attempted it 3 times over the next 8 hours Before my last attempt to restore I resinstalled an repaired ITunes then finally having decided to be patient I sat and watched for the full 24 mins to down load.
Watched it track accross the screen after doing a back up then at point of reinstall or what ever it does it stopped and gave me an error3259 stating my internet link had failed iphone was plugged in... and charging and intermittantly syncing during the day so I had no problems with that side Just very confused about internet link breaking as it was hardwired and safari & google chrome were working perfectly
Apple Tech guys please sort out this softwate update or at least tell me where the download is stored so I can manually install it to update my phone as 'm loosing phone no through sync regualarly
Ps My background is was an NHS pharmacy computer systems manager for 17 years so I do understand a bit about installing software on various platforms
any ideas would be appreciated

I have an IPad2. I've received two different ideas on charging the battery. One person indicates I should let the battery run almost down before recharging; another person indicated I should keep it charged closer to 100% . What is the best process?

I have an IPad2. I've received two different ideas on charging the battery. One person indicates I should let the battery run almost down before recharging; another person indicated I should keep it charged closer to 100% . What is the best process for the best battery life over time?

I do exactly as Thomas Reed does. Always have from day one. Going on 15 months now and I get at least 10 hours of use out the battery every day. No matter how much juice is left on the device when I go to bed - I put the iPad on the charger - doesn't matter what the battery gauge says - I plug it in and let it charge all night.

Best Buy moved delivery date by 20 days only 18 hours before originally scheduled delivery

I purchased a Samsung gas range/convection oven on December 3, 2014. Delivery was scheduled for December 30, 2014. On December 29th, at 12:05 p.m. CST, a mere 18 hours before scheduled delivery, Best Buy emailed me to alert me that the delivery had been unilaterally rescheduled until January 19th.
Unfortunately, do to the late nature of the notice of rescheduling, I had already sold/gotten rid of my old oven. In response to this issue, I contacted Best Buy customer service and, after speaking with 6 different people of the course of 2.5 hours, was provided the following options: 1) Cancel your order; 2) Wait until the order is filled; or 3) Contact your local stores to check for availability.
When asked if Best Buy would consider providing a partial discount on the oven purchase to cover the potential costs associated with renting an interim stove, the customer service representative told me that she was unable to help me in that regard and to ask my local store.
Has anyone had experience getting a similar situation effectively resolved? Has anyone ever spoken to a customer service representative with Best Buy that was actually able to resolve an issue?

Dear rtjamison,
When receiving a scheduled delivery date like this, I can understand your foresight around creating the space for your new oven by getting rid of the old one beforehand, and I respect that. It pains me to hear that this responsible act will now affect you negatively due to the untimely rescheduling of your order. I am very sorry for any inconvenience this has already caused you.
On occasion, orders can be rescheduled because of sudden inventory constraints. Other times, scheduling issues can occur if a store is the one fulfilling the delivery and are absent an available delivery driver due to sickness; although, you would typically be provided with an explanation around this. Without being able to look up your order, I am not sure what the reason was in your case specifically. The options you were provided by the phone agent are all viable choices; however, I would like to work with my support team to see if there are any other options available to us at this time.
As I was unable to pull up your purchase history using your email address you provided here on the forums, I will be reaching out to you via private message to obtain your purchase information so I may investigate further. To check your private messages, click on the envelope in the upper right-hand corner while you are logged into the forums.
Sincerely,
JD|Social Media Specialist | Best Buy® Corporate
Private Message

Iphone has been in recovery mode for 4 hours and hasn't come back to the home screen and how can i fix this and get it back to working order?

iphone has been in recovery mode for 4 hours and hasn't come back to the home screen and how can i fix this and get it back to working order?
the iphone 4S has been in recovery mode for a long time and i have tried to press and hold the power and home buttons until the apple symbols comes on the screen again but it stay on the screen until the screen turns off and doesn't come back on to the home screen and have tried to sync with mac and doesn't do anything it does display the itunes and cable icons for a while but then goes back to the apple symbol and doers nothing what can I do to fix this and not loose what is on the phone at all?

Hi, simonRM.
Thank you for visiting Apple Support Communities.
I understand that you are unable to restore your iPhone. Here are the best troubleshooting resources to start with when not being able to update or restore your iPhone.
If you can't update or restore your iPhone, iPad, or iPod touch
Resolve iOS update and restore errors in iTunes
-Jason H.

My keynote seems to be misbehaving. Me, a teacher was preparing a ppt on keynote.all of a sudden, the navigator column to my left goes black and nothing seems to move. Please help! Only 12 hours before I take class.

My keynote seems to be misbehaving. Me, a teacher was preparing a ppt on keynote.all of a sudden, the navigator column to my left goes black and nothing seems to move. Please help! Only 12 hours before I take class.

Hi KRKabutoZero,
Welcome to Apple Discussions
You may want to look at Knowledge Base Document #58042 on A flashing question mark appears when you start your Mac.
Do you have access to another Mac? You may want to backing up your files via Target Disk Mode (TDM) as well as running some utilities (Knowledge Base Document #58583 on How to use FireWire target disk mode.
You may want to invest in a utility like DiskWarrior from Alsoft. It is great for troubleshooting drive malfunctions.
As said before, you may also want to bring your iBook to your local Apple Store/Reseller.
Jon
Mac Mini 1.42Ghz, iPod (All), Airport (Graphite & Express), G4 1.33Ghz iBook, G4 iMac 1Ghz, G3 500Mhz, iBook iMac 233Mhz, eMate, Power Mac 5400 LC, PowerBook 540c, Macintosh 128K, Apple //e, Apple //, and some more... Mac OS X (10.4.5) Moto Razr, iLife '06, SmartDisk 160Gb, Apple BT Mouse, Sight..

Time based mode runs 4 hours before time set

Similar Messages

Maybe you are looking for