Tm2t touch screen and pen input completely dead

i have a 2 week old tm2t (2100) laptop and its touch input is completely dead..
i reinstalled os..
updated bios
updated graphics drivers
updated wacom drivers
after doing all these things also its not working.. can some one pls help me....
This question was solved.
View Solution.

here are the pics i took wen i opened my laptop
as mentioned 2 screws are below the rubber
and the third screw is as shown in the pic below
i have removed the 3rd screw in the pic
there will be 4 screws which hold the LCD screen
i have removed the screws and taken a pic..
.. unscrew them and slowly lift the LCD screen.
here is a close up of the connecting wire....
HP knows that this kind of connector gives problem, they had put a tape on this connector..
i removed the tape, pushed the wire to the connector and put the same tape which was previously present..
boot the system and done,,, perfectly working touch screen

Similar Messages

Touch screen and pen/stylus stop working - Helix

Note taking with my new Helix is unbelievably frustrating! It's Windows 8 Pro -- fully updated (Windows and Lenovo drivers and apps). I am using Microsoft OneNote 2013. The problem is regular locking up or freezing of one or the other of the touch screen or the pen / stylus. Sometimes the pen still works, but fingers on the touch screen have no effect. Other times the the touch screen works, but not the pen. I'm not 100% certain that it's limited just to OneNote, but that's where it's guaranteed to happen. I can "fix" the problem most of the time by putting the Helix into sleep mode and then waking. Other times I have to shut down and restart. During a two hour session this will happen a dozen times at least. This makes it nearly unusable. Rob

teachmoorenglis wrote:
Just got this Helix for a test-drive and I'm already having problems with the stylus/touch. I can't quite tell why, but after working with computer as a tablet for a while, the touch turns off. Then, if I pull the stylus out of the pocket 1/2 inch or so, the touch turns back on, then about 30 seconds later it goes off. Then, if you pop the stylus back into the slot all the way, the touch screen is fine again for several minutes. Over and over, i'm finding the interplay between touch and stylus to be a bit quirky. Maybe it's the machine i got or maybe it's a general problem. I have had the exact problem with the touchscreen not working without fiddling with the pen in the socket (put it in, take it out, touch it etc). Do you have the task bar on the left hand side? I've had diffiuclties with the digitizer, can't use the bottom or right of the screen for example. I'm wondering if still detects that the pen is near it. If I see the problem again I'll be trying the task bar on the right side. If that doesn't help I have to assume a broken switch in the pen holder / bad digitzer. Neither of which is good on a 2500 chf machine, especially one with what seems to be a warped tablet or base (still have to measure that).

After ios7 upgrade to my 4s, touch interface keeps freezing on me and the screen rotation feature us completely dead. Any ideas?

After ios7 upgrade to my 4s, touch interface keeps freezing on me and the screen rotation feature us completely dead. Any ideas?

You can try resetting your iPhone by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists.

Problems with Illustrator CC 2014 in Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen.

Hello to everybody!
Some times ago Adobe has updated Illustrator to CC 2014 version and now it support touch pressure\pan\zoom in Windows 8 tablets. I have Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen with pressure-sensitive support.
I was extremely disappointed that the brush in new version does not work correctly. Watch the video please that I did specifically for the demonstration.
I use Adobe Illustrator CS6 and Adobe Illustrator CC 2014 for comparison. In the old version the brush is works correctly. You must do a lot of clicks to start the brush in CC 2014 version (please see video). What causes of the problem? Please help me!

Hello to everybody!
Some times ago Adobe has updated Illustrator to CC 2014 version and now it support touch pressure\pan\zoom in Windows 8 tablets. I have Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen with pressure-sensitive support.
I was extremely disappointed that the brush in new version does not work correctly. Watch the video please that I did specifically for the demonstration.
I use Adobe Illustrator CS6 and Adobe Illustrator CC 2014 for comparison. In the old version the brush is works correctly. You must do a lot of clicks to start the brush in CC 2014 version (please see video). What causes of the problem? Please help me!

Windows Touch Screen Stylus Pen use for Photoshop

I was have Windows touch screen and I want to use a styles pen. However, when I try to use the pen it will not draw, but just move the picture around. How can I fix this? Thank you

[Apologies for the multiple versions, but I also raised this issue in another part of the forum where there's an active Helix discussion, so there's another conversation happening in the thread "When is the Helix release date?", around page 59]
For those experiencing this problem, I'm becoming convinced that it's mostly going to occur in OneNote. Here is a "solution" I'm testing; it's not a proper fix but it works.
OneNote has the ability to automatically detect whether or not you're using your finger to pan, your pen nib to write, or your pen eraser (if you have one) to erase. It's controlled by a setting under File-Options, Advanced. Look for the Pen settings. You'll see "Automatically switch between inking, selecting, typing and panning." It's checked by default. If you uncheck it, then your eraser won't work anymore, and you have to manually switch between inking, erasing and panning; to make this easy I dropped those icons into my quick access bar.
I think this is a Helix problem, not a OneNote problem. On my Dell Latitude 10 tablet, I do not have this problem. There's something about the Helix sensors and/or drivers that isn't working quite right, so it can't consistently figure out what's up with the pen, and it gets stuck.

JME support for touch screen and vibration

Hi all, How are you?
I need to develop a application for mobile phone, and it is going to use the mobile touch screen and vibration features.
Does somebody know if there is an JME API, or JSR that provides access/control to Mobile's touch screen and vibration features?
Does somebody know if it is feasible to do it using JME?
I appreciate any help you can give,
thanks in advance,
Roger

to use the mobile touch screen javax.microedition.lcdui.Canvas methods
-- hasPointerEvents()
-- hasPointerMotionEvents()
-- pointerDragged(int x, int y)
-- pointerPressed(int x, int y)
-- pointerReleased(int x, int y)
and vibration features?javax.microedition.lcdui.Display method
-- vibrate(int duration)
Also see proprietary vibration etc. APIs for Nokia / SonyEricsson:
{color:#0000ff}http://www.wmlscript.it/j2me/nokia-UI-API-v11/com/nokia/mid/ui/DeviceControl.html
http://developer.sonyericsson.com/entry.jspa?externalID=108&categoryID=12{color}
db

Feature to disable touch screen when pen is detected is no longer available in windows 7

In N-trig drivers with windows vista there was an option where one could select the option to disable the touch input when pen in near the screen. That feature is no longer available when I installed new n-trig drivers in win7.
I use my tablet a lot to take notes. But with dual mode on it detects input where I rest my palm on the screen to write. Every time I have to go and disable touch input completely before I start writing and enable after I finish.
I there any way to enable auto mode with Windows 7 n-trig drivers?
This question was solved.
View Solution.

Thanks for your reply.
I talked about this with HP tech support and they don't know anything about it. I don't even know whether they are qualified enough to provide support. They were just blaming the problems on Microsoft and N-Trig. I knew the problem is with the drivers and I wanted them to let N-Trig know that people like us are waiting to the Auto feature. But instead of considering my complaint they hung up on me not once but twice.

X240 touch screen and smart card seader problem

Hello
I installed Smart Card Reader (FRU 04X3984) to my X240 touch and after that the touch screen doesnt work. OS says that the "no pen or touch input available for this display". If I unplug the SCR cable from MB then touch function is going to work again. There are no conflict messages in system, they just doesnt work together!!

Hello moban2010,
It sounds like you have two separate issues going on here. For the display and touchscreen response I suggest you use the following article to help isolate and resolve the situation.
iPhone, iPad, iPod touch: Troubleshooting touchscreen response
http://support.apple.com/kb/ts1827
For the alert you are getting that your sim card is not installed, there is another great article.
iPhone: Troubleshooting No SIM
http://support.apple.com/kb/TS4148
Thanks for reaching out,
-Joe

Touch Screen and Charge Issue

Hey everyone, first time here but also registered at precentral
Asked there, but I'm hoping here would be a better place to voice this issue.
This is my 2nd New Pre I had as the first one had random keyboard loss when my phone died due to battery. I was able to fix it with a 5th batt pull, but I wasn't chancing it..so swiped it.
Well, got my phone with 1.2.x out of the box and tested fine at the store. When home and updated to 1.3.1. weeks later the issue.
touch would random stop working...I had preware so I decided maybe it was a patch or app messing it up (I noticed I didn't have message foward working after update)
So I Doctored it. The Process went nervously fine, up until I got to the home screen. The Touch went out again!
But after messing around a bit after getting it back after a battery pull (at the time touch comes and goes) I was easily able to recreate the issue.
For example:
Touch = dead, once I plug it into a charger (usb/wall), Touch returns.
Touch = alive, (after it came back during day) Once I Plug in to charge, Touch gone.
There was a point that touch wouldn't return if I had the phone slider closed, with screen unlocked. Wether I was plugging it in or removing to charger.
I hope this makes sense, and really hope its not hardware, as I don't wanna return phone to find out it repeats on a new/refurb one. As this one feels solid in every other dept.
Q's Did palm change how the phone locks..reacts to charger??
If so, god, please fix it!
Post relates to: Pre p100eww (Sprint)

ok, I left work today. in the elevator down to my car i started pandora, bluetooth. Got in the car, docked the phone, plugged in the aux wire to my radio, charger to the phone. Music, couple of calls, music agian, skipped some songs, changed pandora stations, etc...
Got home, undocked the phone, unplugged aux cable and charger, close pandora, turn off the light. Grab my stuff, phone rings can not answer it. Screen now does not work anymore.
Pull the battery twice, no luck. Do some searching and see some post that it is realated to the battery connection and a post that other have got it to work with the charger plugged in.
I take the USB cable, PC to phone and it starts working!! yeah... mess with that batter and no luck. stops working again. unplug the USB from the PC and it is still working. Uplug the USB from the phone, stops working, plug it back in to the phone, not the PC and the screen works again... not really sure what that is about. now it is working with no wire.

Touch Screen and need tip

I was wondering if there was a model similar to Satellite M505-S4990-T but with 15'' monitor.
With 4 GB Ram, Built-in microphone, Long lasting battery, Windows 7 and with touch screen feature.
Can anyone tell me if the touch screen feature works ok? I've heard it has had failures with Vista, however, with Windows 7 it's suppose to work fine.
What's your opinion on this?

In general TouchScreen support in WIndows 7 is vastly improved over Vista. I have no idea about on that specific system though as I haven't used it. And I have no idea if there is a model that meets your specs.
If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.

Windows 8 upgrade problems (touch screen and audio)

my　computer is HP touchsmart 600 1005xt and recently upgraded from windows 7 to windows 8 (64-bit)
after up grading I noticed that the touch screen does not work and and the speakers also did not work

HI,
Here are a few tips that might help you to get your touch screen working:
Activate Windows and install updates by pressing the Windows logo key + W. Type "Activate Windows" into the search field, and then click on the Activate Windows icon that appears in the upper left corner of the screen. In PC Settings, click on Activate Windows, wait for your computer to connect to Microsoft, and then follow the onscreen instructions. Restart the computer. Press the Windows logo key + X, and select Control Panel from the menu. In the upper right corner of Control Panel, select Large Icons from the View by drop down. Click Windows Update. Install touch and/or graphics driver updates. Restart the computer.
Another thing to try: Go to the HP Support and Drivers site and click Drivers and Software. In the search field, enter your product name or number, and then click Next. Select your operating system from the drop-down, and then click next. (If you don't know if your operating system is 32- or 64-bit, press the Windows logo + X key again and select System from the menu.) Follow the onscreen directions to install any appropriate drivers. Restart the computer.
If the touch still doesn't work, try this: Press press the Windows logo + X key, and select Device Manager from the menu. In Device Manager, click the little triangle next to Display Adapters to expand the list. Right-click on the graphics card and select Disable. When asked if you want to disable the card, click yes. Restart the computer. You may have to tinker with your screen resolution.
~Lil.Liebe
Clicking the white KUDOS THUMBS UP on the right is a way to say thanks!
Click Accept as Solution on a reply that solves your issue to help others in search of answers.

HT3529 Hi, my friend was driving me on a e-bike as he was driving he sleeped and he fell and I checked my I pod touch screen and it was cracked so I was wondering if I can get a new one for free or fix it for free so my friend went to apple and told them

Hi my friend was on e-bike he was driving he sliped on oil and we fell I checked my I pod touch 4th gen
Everything works perfectly fine except my iPod touch screen was cracked. Ask one of my friends what to
Do and he said give to apple they'll give you a brand new one or fix it for free just tell them what happened and where you
Bought it I bought mine from source . And one my friends got a new one with out showing receipt or anything
So I was wondering would this work?

The warranty is against manufacturing defect. It is not insurance against accidents. Apple sells Apple Care + (note the +) which does cover accidents, but it does not cover iPods.
Out-of-warranty replacement is the most likely outcome.

Windows 7 Touch Screen and Video Drivers for HP Pavilion tx1219us

Updated to windows 7 and can't find drivers for the Video Driver and Touch Screen. Can anyone help me?

Bummer...
That is even an older GPU than the GMA 900.
It is an Intel 82852/82855 GM/GME Graphics Controller.
OK... I have a possible driver you can use for that. No guarantee it will work great but it should work...
Here is the link to my OneDrive folder.
https://onedrive.live.com/redir?resid=832F4957D2E51B93%21263
Download and unzip the file labeled Intel 82865g Driver (Vista - Win7).
You have to use the manual install method like you did with the other 2.
Good luck!

While reading mail, touched screen and content turned into "Chinese"--on server too!

I cannot now read this email! I've also had problems where I accidentally touch the screen and the email is deleted form the iphone, but I am able to get it off the server. This is a huge problem--as essential email from someone whose address I don't have. Thanks.

OK sorry, I figured out what happened. I somehow moved the message to deleted iems on the server. I don't know how I did that but at least I was able to retreive it. Now if you tell me how to delete this message, I will.

Wake up and phone is completely dead

Ok two nights in a row now that I have woken up to a completely dead iPhone. I upgraded to 4.1 and the multiple tasking *****. I have wifi off, location services off and all that jazz and it is still dead. I even completely log out of skype so that is not running and it's dead. I go to bed with a fully charged battery. Thanks apple I was super later for work today. How can we fix this

There are no "Genius" appointments available at my "local" Apple store so I called Apple support. Apart from them getting my warranty date wrong, they just told me the usual reset, restore, set up phone as new etc. No word of a lie, I have spent over one whole day of my life on all this nonsense.
Apple will NEVER admit that their software has caused problems. I love my iPod and, for a year, I loved my iPhone.....Now I just can't wait until my contract is up when I will be buying an Android phone. I will not be buying Apple ever again!
Apple is only interested in taking more money from you. They provide a thinly veiled support service, but in truth will not spend the time and money on getting to the root of the real problems. iOS4 is not fully compatible with the 3GS.
Cue fanbois!

Tm2t touch screen and pen input completely dead

Similar Messages

Maybe you are looking for