Too small network with AirPort Extreme

I've installed an AirPort Extreme, extended by an AirPort Express, to connect with our cable modem and improve our wireless reception; we now get a strong signal throughout the house.  But with our 7 wireless devices (2 MacBook Pros, 2 iPads, 2 iPhones, and a Kindle Fire), we rarely are successful in logging on more than two of the devices at a time.  For a third or fourth device the icon will merely churn away.  This doesn't fit my idea of a network.  What should I do to improve the situation?

... My question is. If I work with an iPhone, the AE is going to work just with g forcing to TC to work with g as well with the rest of the equipments
The answer is yes, but I believe you can avoid that by having the iPhone connect only to the new dual band TC. Configure *everything else* to run an 802.11n network exclusively - not "802.11n (b/g compatible)". This way the iPhone will be unable to connect to that network, causing it to run in the slower b/g compatible mode. Your iPhone will work fine, as long as it remains within range of your TC's 802.11g wireless network.
Remember that you will need to change all your equipment's settings: the Extreme, the Express, the TC, and maybe the AppleTV.
Galt's rule of networking: "The number of problems you encounter increases exponentially with the number of devices on your network."
So... proceed methodically.
The new TC is very close to AppleTV but wirelessly. Will I increase the speed for watching movies which are placed at TC (through external disks connected to the USB in the new TC) if I connect the TC to AppleTV using an ethernet cable?
The speed will be limited by the slowest link in your network chain. A wired network is always preferable, since it cannot be affected by interference or obstructions.
If you are streaming movies from the Internet, your wireless link will probably be the limiting factor.

Similar Messages

  • Is it possible to set up a network with airport extreme that is not on the internet

    Is it possible to set up a home network using airport extreme that will be a non-internet option?  Not connected to the internet wifi. 

    Is it possible to set up a home network using airport extreme that will be a non-internet option?
    Yes
    Not connected to the internet wifi.
    If the AirPort Exteme is not connected to the Internet, then Internet connections will not be available on wireless or wired connections.

  • Extend a E4200v2 wireless network with airport extreme

    I have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2?
    Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?
    I can't stand the interface. The E4200v2 is brand new.

    Before I suggest you for any trouble shooting steps, I would like to as few questions. Is you Linksys/Cisco router can able to access the Internet. If YES then try the following steps
    1. After unpacking your Airport Extreme, connect the ethernet cable from your jack to the leftmost ethernet port on the back of the Airport. This is the WAN port marked with the small circular image. Next plug the AC adapter into the power port on the Airport and plug it into the wall.
    2. Once the Airport Extreme has been plugged into the network and powered on, the status light on the front will go through a series of colored flashes. When the status light glows solid green, your Airport has been initialized and is connected to the network. This may take a few minutes. If your status light fails to glow solid green, please consult your manual for status light explanations.
    3. Make sure the wireless card on your computer is enabled and turned on. Connect to your Airport Extreme, which will most likely appear as Apple Network followed by some letters.
    4. Next install the Airport software from the included CD. After installation, launch the Airport Utility application. This is located in the Utilities folder in the Applications folder on a computer using Mac OS X, and in Start > All Programs > AirPort on a computer using Windows. 
    Please keep in mind that the Airport Utility is released with a new version every few months, so the screen shots you see below may not look exactly like what you see on your computer.
    5. Select your base station, and then click Continue.
    6. Enter a Wireless Network Name and a Base Station Name and click Continue. Write these names down for future reference.
    7. Enter your Country and Radio Mode on the next screen. Using 802.11n (802.11b/g compatible) is the proper choice in most cases. Click Continue.
    8. Select WPA2 Personal security on the next screen, then enter a Wireless Network Password and Verify it. This password must be between 8 and 63 characters. You should write this password down and keep it near your Airport Extreme in case you forget it. Click Continue.
    9. Select "I connect to my local area network (LAN)" on the next screen and click Continue.
    10. Leave the default settings (Using DHCP) on the next screen and click Continue.
    11. If you are interested in connecting USB peripherals to your Airport, consult your manual for additional information. Otherwise leave the default settings and click Continue.
    12. Enter a Base Station Password and Verify it. Write this password down and keep it near your Airport Extreme. You will need it if you ever want to modify any settings for your base station. Click Continue.
    13. Click Update. Your Airport Extreme base station has been configured and will now restart. Quit the Airport Utility and connect to your new wireless network.
    Check whether it helps you or not..

  • How to configure home network with Airport Extreme + D-Link DIR-665

    *hello everyone,*
    *I had these two working fine together until the D-Link took a dump the other day. No explanation. Just stopped working until I reconfigured everything.*
    *Which then led to my Airport Extreme being unable to connect to the network at all, much less the internet...*
    *My home network is set up like this:*
    *Optimum Cable*
    *Motorola Surfboard modem --> D-Link DIR-655 (via ethernet)*
    *- Provides wifi and ethernet connections on one side of my house*
    *DIR-655 --> Airport Extreme (via ethernet run to other side of house)*
    *- Provides wifi and ethernet connections on the other side of my house*
    *My MBP won't connect to anything other than my AE running N, so I have that set up primarily for my MBP over wifi, while feeding an ethernet connection to a Netgear router running B/G, for my iPhone and other devices.*
    **So here are the relative details:**
    *I decided to start fresh and do a factory default configuration with my Airport Extreme. My working system from earlier was essentially it's own wifi network, but the airport utility 'insists' that I need to run my AE in bridge mode. I've tried that, but I can't get online. I can see my shared connections, so something's getting through, but I cannot connect to them, in addition to being unable to get online.*
    *I'm not really sure how to best illustrate this problem, so I've ran through the process again and jotted down a few notes. Excuse the rambling nature of my narrative, this is a 'blow by blow' account of the Airport Utility setup process:*
    Airport version 7.4.2
    IP address 192.168.0.192
    router address: 192.168.0.2
    Configuring over Airport connection.
    - I want AE to join my current network
    -.. connect AE to my network using ethernet to extend or create second network
    - select device AE will connect to using ethernet - DIR-655 network (displayed w/ airport icon?)
    - create an additional network (through ethernet)
    AE updates..
    - problem 1 of 1 : unsecured wireless network
    wpa wpa2
    Bridge mode or share a single IP address using DHCP
    selected bridge mode
    results: AE has green light, airport utility is satisfied but no connection to network is possible. Shared connections are visible, but unable to access
    next try:
    manual setup
    Wireless mode: create wireless network
    radio mode: 802.11n only (5 GHz)
    channel: auto
    wireless security: WPA2 personal
    (bridge mode still active)
    (this is the exact setup that worked for years before..)
    updated…
    AE light is green, but no connection to internet or shared connections (though visible)
    back to airport utility
    manual setup:
    internet menu:
    connection sharing: share a public IP address
    update
    --> 2 problems
    DHCP Beginning address: 192.168.0.2
    DHCP Ending Address: 192.168.0.2
    chose 'assist me'
    (now one shared connection to Mac Mini becomes active? Had selected it earlier. Able to browse folders, but not share screen)
    AE refreshed now with amber light, with reported problems
    Problem 1 of 2: Internet Connection
    Your Apple Wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network… etc
    - changed IP address to match router IP address (?) Utility goes on to next problem
    Problem 2 of 2: Conflicting DHCP Range
    This Apple wireless device rejected a DHCP address in the same subnet as its internal DHCP server. You should probably switch your Apple wireless device to be in bridge mode. If you still want to be using DHCP and NAT to share a single IP address, you should change your DHCP range.
    - maintain selection: share a single IP address using DHCP and NAT (utility forces you to: ignore; skip; or select bridge mode - which doesn't work..)
    - chose 'skip' for problem 2
    - updated AE..
    New problem:
    Problem 1 of 1: Double NAT
    This Apple wireless device has a private IP address on its Ethernet WAN port. It is connected to a device or network that is using Network Address Translation (NAT) to provide private IP addresses. you should change you Apple wireless device from using DHCP and NAT to bridge mode.
    - selected Bridge Mode
    updated AE…
    "Setup Complete!"
    Unable to connect.
    ** At this point, I am still able to see my shared connections, and while iTunes is open, I can play my shared library that is on my Mac Pro, which connected to the DIR-665 via ethernet, through yet another D-Link router (DIR-615)! I am still connected to the Airport Extreme via wireless, so the system is working, to an extent.*
    *So I'm not sure what to do. How can I remedy my IP address issue? Bridge mode doesn't work (as far as I've experienced), so I'm struggling with my DHCP settings..*
    *Thanks to anyone who has any suggestions!*

    Hi Preston,
    I would recommend not starting the numbering scheme for the IP addresses using a '0'. Yes the range is 0-255, but some numbers are reserved, and not generally good practice.
    Also, assuming you have reset all factory defaults, start anew and have the modem --> router using NAT for dynamic IP addresses --> (other side of the house) Airport Extreme --> not a NAT configuration, but you need a simple switch. Do not use the NAT capabilities on this one. Maybe, just maybe the computer will work now. This will eliminate your double NAT and also help (hopefully) with the D-Link.
    Sorry I cannot help more, I do not own any of the products you talk about, however I have networking experience. Hope it helps.
    --Morris

  • Windows Vista can't log onto wifi network with Airport Extreme

    Several problems with our network. 1. My sister's new Gateway laptop sees the network I set up from my Mac using my airport extreme, but cannot log on to it even when I removed password/encryption - even when I entered 4.2.2.1 and 4.2.2.2 in my DNS server fields. 2. the reason I even did the above is because although my Mac (Titanium G4 Powerbook previously running 10.2.8) could get on the network through the airport, I could not get to any site Google related until I read about the DNS entries as a work around. Yes the work around works but what's the real problem/fix? Regarding probem 1., some advice I'd gotten was to update the firmware on my base station as it might be a compatability issue with that and Vista. I begrudgingly upgraded to Tiger 10.4.6 then downloaded the patch to 10.4.10 (where I am now) which did lead me to an upgrade for my airport (5.3 to 5.6 now). Still, Windows cannot get on to the unsecure network!! What the heck do I need to do?!

    I hope I may have found how to make the vista machines get to your Time Capsule. On the vista system go to network and sharing center. Then click on status, then you will see a window pop up with wireless network info. Click on Wireless properties and then click the advance tab at the bottom, a box without a check mark needs to be checked which says "connect if not broadcasting". I hope I got that right...try it, it's seemed to help for today at least.

  • What are the downsides to extending an Airport Express's network with Airport Extreme?

    Or are there downsides at all, assuming latest generation Airports? I think it happens more often than not that the position of the modem from your ISP in the dwelling is not the ideal location for a router, and it is sometimes inconvenient/impossible to wire an ethernet connection to the optimal location. I have an Airport Extreme and an Airport Express, and was thinking of hooking up the Express to the modem and having the Extreme extend that network, placed at the optimal router location. My concern with that setup is whether the Extreme will use all of its antennas, since the Express has fewer (6 vs 2 if I'm correct).

    Or are there downsides at all, assuming latest generation Airports?
    There are none. You might be confusing such a "wirelessly extended" network with a WDS, which was a horrible compromise with significant disadvantages.
    The optimal location for the second AirPort might not be obvious. Keep in mind that it can only "wirelessly extend" the signal it is capable of receiving. Place it in a location where the wireless signal created by the main router remains strong, while still being able to create a network that covers your required wireless service area.
    Don't worry about the number of antennas or how they are used. They're all used.

  • Networking with AirPort Extreme Base Station

    I am connected to the Internet with an SBC dsl modem, which I have had for a couple of years with few problems. However, I have been having issues networking my Mac G5, 1.8 Mhz machine since I purchased it some time ago.
    In the beginning (before the Mac or -- BM as I like to call it) I was using a D-Link DI-614+ router and running a desktop PC and a laptop PC wirelessly with success. Then I bought my Mac (which I dearly love) and introduced it into my wireless network. At first it seemed to work OK. Gradually and occassionally it would lock up while trying to access an Internet site. Often the problem was resolved by rebooting the DSL modem, the D-Link router and all the computers. This would give me up to several days with no problems, but then things would rapidly deteriorate and I would have connection problems again.
    I thought that if I bought an Airport Extreme base station, that would solve the problems but again, at first things were fine, then rapidly went downhill. I have worked exensively with SBC dsl techs and we have determined that the problem is not with the SBC network or with their dsl modem.
    As it stands now I only get a maximum of a couple of hours of time before the slowing down of the network begins. Some of the error messages I get seem to indicate that there is a problem with the distribution of IP addresses. TCP/IP is set to use DHCP, and I connect by setting PPPoE to my SBC connections settings. "Connect using PPPoE" is unchecked. Location is currently "Automatic" although I have used the connection assistant a number of times in an attempt to get the system up and running.
    I have the same problems in interconnecting the Mac with the two PCs that are on my system. In fact this is even more erratic than connecting to the Internet.
    I have spent many hours with my limited knowledge of these things trying to resolve these issues but have had no success. I have scoured .Mac and other Internet sources and cannot find any specific solution to this problem. I am at a real loss as to where to go next. I am hoping someone here can help or point me in a direction where I might find a solution.
    Thanks,
    Don
    Power Mac G5   Mac OS X (10.4.7)  

    Thank you very much for your response. Yes, the Mac is set to use PPPoE and the SBC information is stored there.
    Just to clean things up, I removed the PPPoE configuration on the Mac and left it unchecked.
    Here is other information about how the system is set up.
    Note: + means item is checked, - means item is unchecked
    Apple Base Station V5.7
    WAN Ethernet Port: Automatic (Default)
    +Enable SNMP Access
    +Enable Remote Configuration
    -Enable Default Host at
    +Enable Remote Printer Access
    -Enable NAT Port Mapping Protocol
    Internet:
    Connect Using: PPP over Ethernet (PPPoE)
    +always stay connected
    Network:
    +Distribute IP addresses
    Airport client computers:
    +Share a single IP address (using DHCP and NAT)
    ((Use 10.0.1.1 addressing))
    Power Mac G5   Mac OS X (10.4.7)  

  • Extend wireless network with Airport Extreme n and Airport Express g

    I have a 4th generation Airport Exteme (n) and an older Airport Express (g) and would like to use the Airport Express to extend my network to the other end of my house, where the signal is very weak. When I tried to set it up tonight, my Airport Extreme disappeared all together and I had to do a hard reset to get it back. I am using a macbook pro 2.4 GHz Intel Core 2 Duo running OS X 10.7.2.  Are there any current insturctions to do this?

    Here's a Youtube video of how to do it. http://www.youtube.com/watch?v=e3EdbRfX1_w
    I had the same set up you do. I did not have success with the Express g. And in my case I had much better success when I sold the Express g on ebay, bought an Express N from the refurb store, so it only cost around $20 get something that is much more reliable.
    I quickly tried to find an Apple Support tech note for you but didn't, post back if you need more.

  • Ad hoc network with airport extreme

    Hi,
    i have no problem setting up an ad hoc network for my canon dslr to wirelessly download images to my MBP after each shot is taken.
    however, i would like to extend the range of this ad hoc network as i want to be able to shoot in another room. can i use the airport extreme to accomplish this?
    if this is possible, may I know how to do it?
    i do not need internet, so this airport extreme just needs to help me extend the range of my current ad hoc network.
    Thank you very much in advance.

    hi,
    is my question too vague?
    do let me know what other info do i need to provide?
    Thanks again
    appreciate any help.

  • Dual N and G Networks with Airport Extreme?

    Hey gang-
    Was at the office store looking at some current wireless N routers, in particular Linksys. They claim to be able to run wireless G 2.4 gig and wireless N 5 gig networks separately and at the same time. One suggestion was to run home computers on the G network and media servers on the N network.
    So, my question is, can the new Airport Extreme run simultaneous dual networks like that as well?
    My plan would be to connect an Airport Express running in 5 ghz N bridge mode to my Tivo and keep the G network for the other computers in the house. Does this sound right?
    Thanks!
    Dave

    If I understand you correctly, I can set up my Time Capsule to run as an "N" only connection and extend the network to my Airport Extreme and run that as a "G" connection?
    As long as you realize that you will not be "extending" the TC wirelessly with the AirPort Extreme. Instead, you will need to connect the two by Ethernet. To extend it wirelessly, would require setting up a Wireless Distribution System (WDS) between the routers ... which will definitely reduce the available bandwidth and compromise performance.

  • AT&T 2wire network with Airport Extreme and Airport Express

    Howdy,
      I have AT&T DSL with a 2wire 2701hg-b plugged in one room but would like to extend my network to connect my Direct TV in my living room.  Can I somehow connect my Airport Extreme (recently purchased) to the 2wire and use my Airport Express to wirelessly connect the Direct TV in the room?  An additional concern is that my wifi keeps dropping on my Macbook Pro but not on my HP laptop. Any guidance/assistance is greatly appreciated.
    Francisco

    Well that's great news. . . I figured it probably just wasn't compatible. Just for the heck of it though, does this tell you anything? (I thought I could post a screenshot but I guess not. Here's the text)
    +Public Routed Subinterface+
    +(check box) Enable+
    +Check ENABLE to create a route from the Internet to the public network specified below.++
    +Router Address:+
    +Subnet Mask: +
    +(check box) Auto Firewall Open+
    +(check box) Default DHCP Pool+
    That was a portion of the 2Wire Routers settings page. What do they mean by Public Routed Subinterface?
    Tyler

  • Extend Network with Airport Extreme & Express

    I am trying to extend the range of a wireless network from one house to another about 80 yards away. I have an Airport Extreme Base Station (ABES) and an Airport Express (AX) which is supposed to accomplish this. I found some instructions in the forums that walked me through configuring WDS. That was easy enough, however, when the AX restarts it doesn't come back up in the Airport Utility. It will come up if I do a hard reset on the AX. The ABES continues to show a WDS error and displays a flashing amber light.
    What am I doing wrong? How do I fix this issue?

    Karen,,, sorry for the interruption. I have the same issue..... AP Extreme Flying Saucer, AP Express "b", and a new AP Express "n" and would like to stop all the drop outs with my music. So, I'll ask Bob for some help.... I think I already know the answer.....
    Bob,,,,, Here is my schematic layout.... Everything is "as the crow flies" and in the same height placement. iMac in bedroom, 1st Stereo in Living room approx 25 feet away, 2nd Stereo in a detach Shop approx 85 feet from the iMac. There is a concrete block wall between the computer and the first stereo and the same block wall along with two big glass windows between the computer and the shop stereo. Again all are in a straight line from the computer.
    The new AP Express "n" is in the shop which is the greatest distance. If the wind is blowing hard I have lots of drop outs in both stereo's..... And during other nice weather times everything works excellent.
    How can I extend the wireless signal??? I'll buy all "n" stuff if you think it'll do the trick....? I can't raise the Dr. Bott antenna due to cord length.... Oh,, my internet modem is plugged into the iMac not the AP Extreme...
    Any suggestions....?

  • Network with Airport Extreme, Airport Express and Time Capsule

    Hi,
    I have a good internet connection working perfectly in the following order. ISP connected by ethernet (cable) to an AE and this extended to an EX and this extended to a new TC. The AE and AX are 801.11 b/g/n but not dual as the new TC. My question is. If I work with an iPhone, the AE is going to work just with g forcing to TC to work with g as well with the rest of the equipments (AppleTV, other iPhones, iMac? I have an iMac that should be connected to the new TC and I would like to do it by 802.11n, is it possible in this configuration? I now that it would better if I organize the network with the new TC (dual) first. However, the TC is too far from the iMac and this is not my favorite option.
    Another question is:
    The new TC is very close to AppleTV but wirelessly. Will I increase the speed for watching movies which are placed at TC (through external disks connected to the USB in the new TC) if I connect the TC to AppleTV using an ethernet cable?
    Thanks,
    Jokin

    ... My question is. If I work with an iPhone, the AE is going to work just with g forcing to TC to work with g as well with the rest of the equipments
    The answer is yes, but I believe you can avoid that by having the iPhone connect only to the new dual band TC. Configure *everything else* to run an 802.11n network exclusively - not "802.11n (b/g compatible)". This way the iPhone will be unable to connect to that network, causing it to run in the slower b/g compatible mode. Your iPhone will work fine, as long as it remains within range of your TC's 802.11g wireless network.
    Remember that you will need to change all your equipment's settings: the Extreme, the Express, the TC, and maybe the AppleTV.
    Galt's rule of networking: "The number of problems you encounter increases exponentially with the number of devices on your network."
    So... proceed methodically.
    The new TC is very close to AppleTV but wirelessly. Will I increase the speed for watching movies which are placed at TC (through external disks connected to the USB in the new TC) if I connect the TC to AppleTV using an ethernet cable?
    The speed will be limited by the slowest link in your network chain. A wired network is always preferable, since it cannot be affected by interference or obstructions.
    If you are streaming movies from the Internet, your wireless link will probably be the limiting factor.

  • Extend existing network with Airport extreme and 3 airport express.

    I want to extend an existing network (thomson TG787v) with an airport extreme (MD031Z/A) with 3 or 4 airport express(MC14Z/A)
    The thomson is the router from the provider and must be used. The building is an old mansion with a lot of brick walls
    I tried to connect the extreme with an ethernet cable (in bridge mode) and then connect the airport express in a line to have wifi in all rooms of the mansion.
    But somehow the airport extremes cannot extend the network.
    Can anyone tell me how to setup the apple devices to make this work?
    Thanks
    Bernhard

    I tried to connect the extreme with an ethernet cable (in bridge mode)
    This is the correct.
    and then connect the airport express in a line to have wifi in all rooms of the mansion.
    Apple's "extend a wireless network" feature will only allow you to "extend" the signal one time. So, the first Express would connect to the AirPort Extreme wirelessly and extend the signal.
    But, you cannot "extend" the signal a second or third time. Each AirPort Express must be located so that it connects directly to the AirPort Extreme.  In other words, each AirPort Express must be located about the same distance from the AirPort Extreme.
    Another way of thinking about his is to visualize the hub and spokes of a wheel. The AirPort Extreme would be located at the "hub".  Each AirPort Express would be located at then end of a "spoke".  As such, each AirPort Express communicates directly to the AirPort Extreme.....not to another AirPort Express at the end of another hub.
    You may need to consider installing Ethernet cable to each location where you will need an AirPort Express and configure the network that way.  Performance wise, this is a much better way to "extend" the network.

  • Expanding a network with Airport Extreme

    I’m trying to extend (or bridge?) my network using my Airport Extreme. My roommate has the modem hooked up to his router and I think it’s a Linksys router. I have an airport card installed in my G4 desktop and I get a decent signal. The reason I want to hook up the Airport extreme is so I can share hard drives and printer with my Macbook Pro I just purchased. I get a fine signal with the Macbook Pro from my roommate’s router as well. The problem is trying to set up the Airport Extreme so I can access the hard drives and printer. I haven’t seen much on using Airport Extreme to expand a network. I was also thinking about running an Ethernet to the desktop from the Airport since it would be faster than the old Airport card I have installed which I believe is only “B”. I would then like to use Back to Mac to access the desktop from anywhere but that is a later issue until I get the airport extreme setup. Any suggestions on how I can extend the network so I can do this. Thanks.
    James

    The only way to do this is by using WDS. Most Linksys devices are not compatible with Apple's WDS but some are. The Linksys WRT54G or WRT54GS (not latest versions v5) are known to be.
    You would need to configure the Linksys and the AirPort Extreme base station (AEBS) to link together using WDS.
    One side effect of WDS is that the wireless bandwidth will be cut in half.

Maybe you are looking for