Transfer ID failed with LUM errors

I have 4 netware servers to migrate to OES2. One was completed successfully using Transfer id a few weeks ago. This weekend I attempted another.
The last part of the transfer id failed with LUM errors that it couldnt access lum objects admingroup, www etc. As we have had one successful migration these objects do exist in the tree and are lum enabled. The /etc/nam.conf was modified prior to starting the transfer id to point to the ldap server with the master replica. I did create too many projects which I think caused me the lum errors which I couldn't get past. With the source server turned off I followed a TID dated 2009 for this LUM error and modified the unix object which had been created to be members of the groups it required, (luckily I had the previously migrated server unix object to compare to) quit the migration software and rebooted the server and then ran ndsrepair. No errors. I did not migrate any services.
Further investigation revealed errors relating to obtaining the SSLCert but it has not expired and despite the cant get it messages the files .der and .pem appeared in the correct folders on the target server. I did copy the .der file to the required location naming it with the ipaddress as per manual instructions. The target server now has a case of dual identity. The nss volumes are mounted ok and the users can map drives using the source server name but the Suse Linux server still thinks that its the pre-migration server when I run a terminal session. Ifconfig shows the correct source server ip. Consoleone is another story. The volume objects are the old ones and the new ones with pools are not showing. From the users viewpoint it works.
Before I do more damage can someone please point me in the right direction. The target name did change to the source before the restart so therefore I should just need to do the hostname rename manually. Should I start at step 7 in the manual instructions in an attempt to fix this server or should I abandon it and start again?

$(UKevin
This defect will make into the next OES2SP2 Patch (post September). We didn't have enough time for QA to regress the fix for September Patch.
-Ramesh
>>>
From:
kjhurni<[email protected]>
To:
novell.support.open-enterprise-server.migration
Date:
10/05/2010 09:06 PM
Subject:
Re: Transfer ID failed with LUM errors
Great, thanks!
As I mentioned previously, we DID find a bug about 3 weeks ago with LUM
repairfailing during the "group" (admingroup). We do have a field
patch for it, but obviously it's not made it into the channel yet.
So if you DO still have that problem, you should probably ask for the
patch (it's one file).
The defect #635574
Should help them reference the bug and get the patch for you.
I'm not sure when it will be released into the patch channel.
Not to say this fixes any and all LUM problems but since we have that
patch, we've not had any issues with the remaining OES2 SP2 64-bit
servers we've done with ID Transfer.
kjhurni
kjhurni's Profile: http://forums.novell.com/member.php?userid=734
View this thread: http://forums.novell.com/showthread.php?t=422454

Similar Messages

Rendering of Proxies in AE fails with generic error messages.

*sigh* working with AVC in CS4 on my quad core has been an exercise in pain.
I've followed the optimization guides linked to in the different forum posts and that lets me zip along until I actually start adding effects. Then I am right back to a crawl. I recently discovered proxies in AE and learned that I can use "replace" in premeire to leverage those same proxies... Sweet... When I works I am back to editing in both in real time!
The problem is AE is regularly failing to generate proxies for me and I cannot figure out why. All my video is shot the same 24mbps, 60fps, 1080p (true 60i). All shot from my Canon HF S10.
The error is always "Error reading frame from file" and it always occurs just before the render is about to complete. Sometimes I get lucky and a working .mov was generated in spite of the error. Bu most times the file isn't there.
So my 2.4ghz quad core with 8gb ram can't edit the originals and I can't create proxies... I'm effectively dead in the water.
I tried using Media Encoder to generate my proxies with no success either. It fails with "Unspecified Error".
Both times I am trying to encode to Quicktime, Jpeg, Draft Settings. For the heck of it I tried different codecs, etc. Nothing seems to help. Even worse is sometimes if I just queue the same file multiple times it eventually works.
Is there anything at all I can do to make successful proxy generation less like winning the lottery?

Yeah I updated to that right away. Premiere itself seems to behave most of the time. To be honest I've hardly had any problems with Premiere even before the 4.2 update.
But AVC (mts files) seem to be very problematic in AE in general. I also experience the issue mentioned here:
http://forums.adobe.com/message/2404464
Sounds like re-encoding to another format is the only way I'll be able to work in AE reliably. So I have to figure out a way to get Media Encoder to finish it's jobs.

Cube refresh fails with an error below

Hi,
We are experiencing this problem below during planning application database refresh. We have been refreshing the database everyday, but all of a sudden the below error is appearing in log. The error is something like below:
Cube refresh failed with error: java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
java.io.EOFException
When the database refresh is done from workspace manually, the database refresh is happening successfully. But when triggered from unix script, its throwing the above error.
Is it related to some provisioning related issue for which user has been removed from MSAD?? Please help me out on this.
Thanks,
mani
Edited by: sdid on Jul 29, 2012 11:16 PM

I work with 'sdid' and here is a better explaination of what exactly is going on -
As part of our nightly schedule we have a unix shell script that executes refresh of essbase cubes from planning using the 'CubeRefresh.sh' shell script.
Here is how our shell looks like -
/opt/hyperion/Planning/bin/CubeRefresh.sh /A:<cube name> /U:<user id> /P:<password> /R /D /FS
Here is what 'CubeRefresh.sh' looks like -
PLN_JAR_PATH=/opt/hyperion/Planning/bin
export PLN_JAR_PATH
. "${PLN_JAR_PATH}/setHPenv.sh"
"${HS_JAVA_HOME}/bin/java" -classpath ${CLASSPATH} com.hyperion.planning.HspCubeRefreshCmd $1 $2 $3 $4 $5 $6 $7
And here is what 'setHPenv.sh' looks like -
HS_JAVA_HOME=/opt/hyperion/common/JRE/Sun/1.5.0
export HS_JAVA_HOME
HYPERION_HOME=/opt/hyperion
export HYPERION_HOME
PLN_JAR_PATH=/opt/hyperion/Planning/lib
export PLN_JAR_PATH
PLN_PROPERTIES_PATH=/opt/hyperion/deployments/Tomcat5/HyperionPlanning/webapps/HyperionPlanning/WEB-INF/classes
export PLN_PROPERTIES_PATH
CLASSPATH=${PLN_JAR_PATH}/HspJS.jar:${PLN_PROPERTIES_PATH}:${PLN_JAR_PATH}/hbrhppluginjar:${PLN_JAR_PATH}/jakarta-regexp-1.4.
jar:${PLN_JAR_PATH}/hyjdbc.jar:${PLN_JAR_PATH}/iText.jar:${PLN_JAR_PATH}/iTextAsian.jar:${PLN_JAR_PATH}/mail.jar:${PLN_JAR_PA
TH}/jdom.jar:${PLN_JAR_PATH}/dom.jar:${PLN_JAR_PATH}/sax.jar:${PLN_JAR_PATH}/xercesImpl.jar:${PLN_JAR_PATH}/jaxp-api.jar:${PL
N_JAR_PATH}/classes12.zip:${PLN_JAR_PATH}/db2java.zip:${PLN_JAR_PATH}/db2jcc.jar:${HYPERION_HOME}/common/CSS/9.3.1/lib/css-9_
3_1.jar:${HYPERION_HOME}/common/CSS/9.3.1/lib/ldapbp.jar:${PLN_JAR_PATH}/log4j.jar:${PLN_JAR_PATH}/log4j-1.2.8.jar:${PLN_JAR_
PATH}/hbrhppluginjar.jar:${PLN_JAR_PATH}/ess_japi.jar:${PLN_JAR_PATH}/ess_es_server.jar:${PLN_JAR_PATH}/commons-httpclient-3.
0.jar:${PLN_JAR_PATH}/commons-codec-1.3.jar:${PLN_JAR_PATH}/jakarta-slide-webdavlib.jar:${PLN_JAR_PATH}/ognl-2.6.7.jar:${HYPE
RION_HOME}/common/CLS/9.3.1/lib/cls-9_3_1.jar:${HYPERION_HOME}/common/CLS/9.3.1/lib/EccpressoAll.jar:${HYPERION_HOME}/common/
CLS/9.3.1/lib/flexlm.jar:${HYPERION_HOME}/common/CLS/9.3.1/lib/flexlmutil.jar:${HYPERION_HOME}/AdminServices/server/lib/easse
rverplugin.jar:${PLN_JAR_PATH}/interop-sdk.jar:${PLN_JAR_PATH}/HspCopyApp.jar:${PLN_JAR_PATH}/commons-logging.jar:${CLASSPATH
export CLASSPATH
case $OS in
HP-UX)
SHLIB_PATH=${HYPERION_HOME}/common/EssbaseRTC/9.3.1/bin:${HYPERION_HOME}/Planning/lib:${SHLIB_PATH:-}
export SHLIB_PATH
SunOS)
LD_LIBRARY_PATH=${HYPERION_HOME}/common/EssbaseRTC/9.3.1/bin:${HYPERION_HOME}/Planning/lib:${LD_LIBRARY_PATH:-}
export LD_LIBRARY_PATH
AIX)
LIBPATH=${HYPERION_HOME}/common/EssbaseRTC/9.3.1/bin:${HYPERION_HOME}/Planning/lib:${LIBPATH:-}
export LIBPATH
echo "$OS is not supported"
esac
We have not made any changes to either the shell or 'CubeRefresh.sh' or 'setHPenv.sh'
From the past couple of days the shell that executes 'CubeRefresh.sh' has been failing with the error message below.
Cube refresh failed with error: java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
java.io.EOFException
This error is causing our Essbase cubes to not get refreshed from Planning cubes through these batch jobs.
On the other hand the manual refesh from within Planning works.
We are on Hyperion® Planning – System 9 - Version : 9.3.1.1.10
Any help on this would be greatly appreciated.
Thanks
Andy
Edited by: Andy_D on Jul 30, 2012 9:04 AM

At DI R3trans fails with this error code ORA-12545, but CI runs

Hello Gurus,
We have our BW System on two instances with a separated oracle database server.
Last week the system was unreachable and we must restarted it hard.
After that, the Listener could started and runs. The DB could started, mounted and opened successfully.
Now we have a special problem.
The central instance can connect at startup to the database. But the dialog instance not.
The DI get the following error:
|> R3trans -x
This is R3trans version 6.14 (release 701 - 12.06.09 - 15:20:00).
2EETW169 no connect possible: "DBMS = ORACLE                           --- dbs_ora_tnsname = 'BW2'"
R3trans finished (0012).
The trans.log entry are:
4 ETW000 [dbsloci.    ,00000] *** ERROR => CONNECT failed with sql error '12541'                        17 0.187511
4 ETW000 [dev trc     ,00000]     set_ocica() -> SQL error code 12541                                    13 0.187524
4 ETW000 [dev trc     ,00000] -->oci_get_errmsg (con_hdl=0, rc=12541)                                   14 0.187538
4 ETW000 [dev trc     ,00000]     OCIErrorGet -> SQL error code: 12541                                   14 0.187552
4 ETW000 [dev trc     ,00000]     ORA-12541: TNS:no listener
4 ETW000                                                                                22 0.187574
4 ETW000 [dblink      ,00433] ***LOG BY2=>sql error 12541 performing CON [dblink#4 @ 433]           14396 0.201970
4 ETW000 [dblink      ,00433] ***LOG BY0=>ORA-12541: TNS:no listener [dblink#4 @ 433]                   39 0.202009
2EETW169 no connect possible: "DBMS = ORACLE                           --- dbs_ora_tnsname = 'BW2'"
A telnet connection test to port 1527 are also unsuccessful.
But sporadicly the telnet or R3trans connection are successful, but the second check are unsuccessful.
We have checked the telnet connection to another oracle database server (ERP) at port 1527 and it works.
The CI have some entry's in ST22 with DBIF_RSQL_SQL_ERROR --> ORA-03114: not connected to ORACLE.
Are someone known something about this issue?
regards
Chris

@ Sunny Pahuja:
We checked sapmnt.
Sapmnt is common on CI and DI. It was never mounted on DB. But DB runs perfectly until this issue.
@ Ankit Gupta
We checked the configuration of listener.
It is the same like the listener configuration of our ERP system with CI, DI and DB on separate Servers, too.
@ Rajesh Narkhede
From DB Server
|> tnsping BW2
TNS Ping Utility for IBM/AIX RISC System/6000: Version 10.2.0.2.0 - Production on 06-MAY-2010 07:40:56
Copyright (c) 1997, 2005, Oracle. All rights reserved.
Used parameter files:
/oracle/BW2/102_64/network/admin/sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (COMMUNITY = SAP.WORLD) (PROTOCOL = TCP)
(HOST = bw2dba) (PORT = 1527))) (CONNECT_DATA = (SID = BW2) (GLOBAL_NAME = BW2.WORLD)))
OK (100 msec)
On CI and DI we don't have tnsping.
Just copy it don't work.
|> tnsping BW2
TNS Ping Utility for IBM/AIX RISC System/6000: Version 10.2.0.2.0 - Production on 06-MAY-2010 08:39:17
Copyright (c) 1997, 2005, Oracle. All rights reserved.
Message 3511 not found; No message file for product=network, facility=TNS
Message 3512 not found; No message file for product=network, facility=TNS
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (COMMUNITY = SAP.WORLD) (PROTOCOL = TCP)
(HOST = bw2dba) (PORT = 1527))) (CONNECT_DATA = (SID = BW2) (GLOBAL_NAME = BW2.WORLD)))
Message 3509 not found; No message file for product=network, facility=TNS
How to get it on the CI and DI. In the SAR files at SAP it is not included. I can't found something in the Web.

I ve updated my i pod touch to version 6.0.1. Installation got failed with some error msg, and now my i pod is not getting detedted in my system.Help me to fix it up.

i ve updated my i pod touch to version 6.0.1. Installation got failed with some error msg, and now my i pod is not getting detedted in my system.Help me to fix it up.

What's the error mesage?

The installation of SAP Front-End components failed with 95 errors.

I tried to install SAP GUI 7.20 on Windows Vista X64. And I got this error message:
The installation of SAP Front-End components failed with 95 errors.
This 7.20 version used to run on this operating system fine. I reinstalled the OS, and now I got this.

Hi,
I suppose you reinstalled the same OS.
Did you install the JSDK (java) afterwards. As you must be aware Java is a pre-requisite for the SAP Frontend.
Also make sure you have set the environment variables after installing java.
Further documentation, the SAP installation manual can be found in the u201CDOCUu201D folder of the installation software.
Regards,
Rohan.

IDoc failed with the error massaeg "Instance of object type could not be ch

Hi All
I am getting IDoc failed with the error massaeg "Instance of object type could not be changed"
Message type :PORDCR
Basic type : PORDCR05
Message no. BAPI003
Status : 51
All POs are get uploaded in SAP during Cut over activities only.
Please suggest on this.It will be a great help.
Thanks
Ajit

Hi
After uploading POs into SAP we are changing quantity and value in PO in Legacy system, and for this all IDocs are failed, subsequently these changes are not triggering to ECC.
Please help
Thanks
Ajit

External Drive Disk Erase Failed with the Error Input/Output Error

I have 2 hard drives in an external FW800 enclosure that I am unable to format. When I go to initialize the drives in Disk Utility, I get the following error message: "Disk Erase failed with the error: Input/output error."
The drives show up in Disk Utility, but I can't repair them (that option is grayed out). Disk Utility correctly ID's the manufacturer of the drives (Maxtor), their size (200gb each), so it's obviously seeing that the drives are there. But it won't let me format them.
The drives are new, by the way; they don't have any data/files on them. I have Disk Warrior, but the drives don't show up there to be repaired -- probably because they aren't formatted yet.
After looking at other posts, I tried switching the jumper settings around on the drives -- from Master/Slave to cable select and back again, but it didn't help. I also tried doing a zero erase (even though the drives are new), zapping the PRAM -- again, no help.
One question I had is whether this could be a bad FW800 cable? The cable is new -- it came with the enclosure, which is an OWC Dual FW 800 enclosure. Other than that, does anyone have any other thoughts about what's causing this? Any help would be greatly appreciated.
Matthew

SOLUTION!!!!
I had the exact same problem. I have the original 20 GB hard drive that came in my Powerbook G4 550MHz and a couple of years ago I traded up for a 60 GB drive and bought a FW/USB enclosure for my original drive to use it to backup my important files. I hadn't backed up in over a year (shame on me!) and I decided maybe I should erase the drive and start from scratch. It was connected via USB.
At that point DiskUtility gave me the exact same Input/Output error. I tried partitioning the drive into 1 or more partitions but came up with the same error. I couldn't figure out what was wrong so I decided to startup in OS 9.2.2, I did that and let it start up, then plugged in the hard drive and it gave me the standard "This disk is unrecognizable, do you want to eject or erase?" so I clicked Initalize. It worked!
Just make sure you choose the MacOS Extended option when initializing out of OS 9 (instead of the MacOS Standard option) so it can be read and viewed in OS X.
If your computer is too new to be able to boot from an OS 9 folder on your drive or an OS 9 CD, then see if a friend or a local library has older computers that are running OS 9 or can boot from it. If not let me know and you can send me your drive and I'll reformat it.
Kind of crazy...I haven't used the OS 9 partition on my HD in YEARS...was even thinking about erasing it since I don't use any Classic applications anymore...good thing I didn't!
Nick
Powerbook G4 550Mhz Mac OS X (10.4.6)

Is my HD Dead? Reformat Disk Utility Error: secure disk erase failed with the error could not open disk.

Hi,
Fed up with seeing the spinning beach ball I decided to reformat my MacBook Pro...
After backing up everything on an external hard drive I put in the OSX install DVD, restarted the machine and held down 'C'.
I followed the install prcedure, clicking next a few times etc...
I then went into Utilities > Disk Utility. I chose 7-Pass to erase the Macintosh HD and set it off erasing.
I checked the process an hour in and message on screen read:
Secure disk erase failed with the error:
could not open disk
The internal hard drive no longer exists in the disk utility so I cant retry erasing it.
The only thing that appears in disk utility is the OSX install DVD.
I can't even shut down the mac as everything under the apple tab is greyed out!
I'm guessing this means my hard drive is broken right?
If anyone has any other ideas of what to try I'd really appreciate that.
How do I turn the machine off?
If my hard drive is gone then should I consider getting an SSD drive?
Any recommendations for such a drive would be great.
Hope you can help!

Did you partition the drive?
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

Partition Failed Partition failed with the error: POSIX reports: The operation couldn't be completed. CAN NOT ALLOCATE MEMORY

I plug usb mass storage device to my macbook pro i7 than every thing is stack and i reinforce to shutdown and than I start again but mac fail to boot again.
I tried different optiones in disk utility in mac os startup disk. but still fail to repair, erase and partition. I try to fix with the steps listed in
https://discussions.apple.com/message/13288923#13288923
but it fail to partition with the msg:
Partition Failed
Partition failed with the error: POSIX reports: The operation couldn’t be completed.cannot allocate memory
pls pls pls help urgentely on this matter I stop working.
Kind Regards,
pe

Hi again OGELTHORPE.
I've already run two hardware tests. One quick one and one extended one. It was unable to pick anything up.
It's like everything is running perfectly, but when I go to erase the HDD or partition it, it pops up with the error message. Even when I try to erase and partition using "Terminal", I received the same error message.
It's beginning to do my head in, but will see if replacing the SATA cable will make any difference. If it doesn't, I'll hazard a guess it could be the Logic Board.
Thanks again for your suggestions!
L.

Windows Server 2012 Windows Backup failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).

The Volume Shadow Copy service initially was running under the context of System, so we thought that ‘System’ doesn’t have permissions to access network shares.
When the Volume Shadow Copy service was running under the context of System, this was the error logged:
“failed with following error code '0x8078014B' (There was a failure in creating a directory on the backup storage location.).”
Which is likely due to not having permissions to write to the network location.
This is a scheduled backup trying to write to a network location, so we changes the service to run under the context of an account that does have permissions to write to the network share.
  Then the error changed to this:
“failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).”
HRESULT 0x8078006b
DetailedHRESULT 0x8004230f
ErrorMessage %%2155348075
BackupState 12
VolumesInfo <VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0"
BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0"
TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228"
DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0"
FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0"
/></VolumeInfo>
We aren’t really seeing anything that gives any hint on what the issue is.
Any ideas? Thanks in advance!

We are trying to back up folders/files from 2 local drives (C: & D:), both of which have only 10% space used, and 100 GB free.
We are attempting to back the files up to a Remote Shared File (and there is 100+ GB free space out there).
  If we try another network location, we receive the exact same error.
This is Windows Server 2012, not running Hyper-V and is a physical server not a VM.
Thank you for the link.
Looking in:
Event Viewer / Application and Service Logs / Microsoft / Windows / Backup / Operational
But it doesn’t seem to give any more details:
Log Name:
Microsoft-Windows-Backup
Source:
Microsoft-Windows-Backup
Date:
7/8/2013 8:00:12 PM
Event ID:
5
Task Category: None
Level:
Error
Keywords:
User:
SYSTEM
Computer:
servername.edu
Description:
The backup operation that started at '‎2013‎-‎07‎-‎09T02:00:06.273000000Z' has failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).
Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Backup" Guid="{1DB28F2E-8F80-4027-8C5A-A11F7F10F62D}" />
<EventID>5</EventID>
<Version>3</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2013-07-09T02:00:12.872602100Z" />
<EventRecordID>30</EventRecordID>
<Correlation />
<Execution ProcessID="3028" ThreadID="3996" />
<Channel>Microsoft-Windows-Backup</Channel>
<Computer>servername.edu</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="BackupTemplateID">{A421E864-A115-4288-8D12-F4878CF8A248}</Data>
<Data Name="HRESULT">0x8078006b</Data>
<Data Name="DetailedHRESULT">0x8004230f</Data>
<Data Name="ErrorMessage">%%2155348075</Data>
<Data Name="BackupState">12</Data>
<Data Name="BackupTime">2013-07-09T02:00:06.273000000Z</Data>
<Data Name="BackupTarget">\\servername\BACKUP</Data>
<Data Name="NumOfVolumes">2</Data>
<Data Name="VolumesInfo"><VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0"
IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem
Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0"
NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /></VolumeInfo></Data>
<Data Name="SourceSnapStartTime">2013-07-09T02:00:06.289250300Z</Data>
<Data Name="SourceSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="PrepareBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PrepareBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="TargetSnapStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="TargetSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="DVDFormatStartTime"><TimesList></TimesList></Data>
<Data Name="DVDFormatEndTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyStartTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyEndTime"><TimesList></TimesList></Data>
<Data Name="BackupPreviousState">2</Data>
<Data Name="ComponentStatus"><ComponentStatus></ComponentStatus></Data>
<Data Name="ComponentInfo"><ComponentInfo></ComponentInfo></Data>
<Data Name="SSBEnumerateStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBEnumerateEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SystemStateBackup"><SystemState IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="BMR"><BMR IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="VssFullBackup">false</Data>
<Data Name="UserInputBMR">false</Data>
<Data Name="UserInputSSB">false</Data>
<Data Name="BackupSuccessLogPath">
</Data>
<Data Name="BackupFailureLogPath">
</Data>
<Data Name="EnumerateBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="EnumerateBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupFlags">0x9</Data>
<Data Name="ComponentInfoSummary"><ComponentInfoSummary ComponentInfoArrayPresent="1" TotalComponents="0" SucceededComponents="0" /></Data>
</EventData>
</Event>

Partition failed with the error: No space left on device

I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!

arajs wrote:
I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!
This is a standard error message.
If you would have checked into the bootcamp forum you would have instantly found the solution.
http://discussions.apple.com/forum.jspa?forumID=1244&start=0
All that error message means is that you do not have enough conguous disk space available. No big deal at all for an older system. You have bits of files strewn over the "free space."
The solution as you would find in the bootcamp forum is to clone your HD, using a file-file clone, then test the clone to be sure it is working and then to erase your HD and clone back.
Works every time.
Message was edited by: Theodore

Import error imp-00017: following statement failed with oracle error 1659:

Hi all,
I am trying to import a file (dmp) which is of 1.63GB size,
when I type
imp
dbname/pwd@db
c:\filepath
30720
no
no
yes
yes
yes
I am getting the error imp-00017: following statement failed with oracle error 1659:
-- end it says Ora-01659 unable to allocate minextents beyond 1 in tablespace USERS
--unable to create INITIAL extent for segment in tablespace USERS
--import terminated successfully with warnings
when I looked into
select maxbytes,file_name from dba_data_files where tablespace_name='USERS';3.4360+10 c:\oracle\product\10.2.0\oradata\orcl\users01.dbf
kindly help me in solving this is.
Regards,
aak
Edited by: AAK 460425 on Apr 12, 2009 6:33 PM

Thanks,
select bytes from user_free_space where tablespace_name='USERS'
BYTES
458752
720896
458752
655360
43384832
is the size less?
My apology I have updated this in the below thread, which is same as this one.
Re: Import error

SharePoint SiteMialbox failed with 503 error (AutoDiscover.svc web service call failed)

SharePoint SiteMialbox failed with 503 error (AutoDiscover.svc web service call failed)
I followed Technet articles to configure SiteMailBoxes in our environment & exchange sever.
When we created Sitemailbox in a SiteCollection &when we try to open it, it failed with below error.
Site Mailbox
We are having trouble connecting to Exchange Server
The server might be temporarily unavailable. Please check back on this page in a few minutes. If this problem persists, please contact your system administrator.
Correlation ID: bb0fe99c-6f4e-e084-b191-881fbf0fa977, Error Code 10
ULS Log (503 error)
Autodiscover Diagnostics Response Headers: request-id: 95d12ceb-283e-4495-b28b-256503fd097c client-request-id: 742fe69c-ef5a-e084-ca05-6098c759c584 X-CalculatedBETarget: devapwxyz01a.devap.mydomain.com X-FEServer: DEVNAABCD01B
Content-Length: 0 Cache-Control: private Date: Tue, 03 Feb 2015 18:53:40 GMT Set-Cookie: X-BackEndCookie=; expires=Sun, 03-Feb-1985 18:53:40 GMT; path=/autodiscover; secure; HttpOnly Server: Microsoft-IIS/8.5 X-AspNet-Version:
4.0.30319 X-Powered-By: ASP.NET
742fe69c-ef5a-e084-ca05-6098c759c584
if I am correct, X-CalculatedBETarget supposed to be DEVNAABCD01B.devna.mydomain.com but it connected to different domain devapwxyz01a.devap.mydomain.com. Do you guys have any idea on this? (I verified
the same using fiddler, it is failing right at autodiscover.svc call.)
I wrote a powershell script to connect autodiscover service in sharepoint server & this web service call able connect right server X-CalculatedBETarget. It gave the expected response.
I am not sure why SharePoint webservice call (X-CalculatedBETarget) is going to different server?
let me know if you guys have any ideas.
Thanks.

Thanks for the Response Raj.
I already followed the same instructions in the Links.
When SharePoint Autodisover.svc webservice send a request to Exchange server & Exchange server redirecting that request to different server, this is the problem i am facing right now.
X-CalculatedBETarget
supposed to be DEVNAABCD01B.devna.mydomain.com but it connected to different domain devapwxyz01a.devap.mydomain.com.
Let me know if you have any suggestions?

After downloading and creating the MSI for Lightroom, the install fails with no errors reported. Checking compatability, windows comes back with not compatible on both win 7 and 8.1.

Installer MSI fails with no error or message of any kind. Tested compatability with the windows compatability check and it comes back as not compatible. What now?

Hans,
It is a known problem on Windows 98, Windows and Windows 2000 if you are using Intel Pentium 4 processor with Sun JRE and Symantec JIT. I had the same problem with Windows 98. Oracle has a patch. Please see Note:131299.1 on metalink for details.

Transfer ID failed with LUM errors

Similar Messages

Maybe you are looking for