U430 Touch Screen Settings / System Question

Is there anyway to adjust the touch screen for the ideapad U430? I have noticed over the last couple of days the touch screen is getting more and more difficult to click on things. I have only had the laptop about a week, if that. Also, does anyone know why this computer is soooo slow? I know it comes with a lot of programs installed and I've uninstalled and only installed a couple (literally) of my own programs I needed. I have had Geek Squad already run test and clean it up. I do a disk clean up daily, it multiple times a day. I've defragmented and optimized as well. Just curious why the computer freezes or the internet takes about 45 seconds to 1 minute to load a page sometimes? As time goes on, its getting longer and longer timing before the page will appear. 

Mine freezes from time to time as well, hybrid hard drive is the culprit. Internet slowdown is due to the Intel WiFi driver. Update to the latest Intel driver and you'll notice a huge improvement. You can get it from here:
https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=23707&lang=eng&OSVersion=Windows%208...

Similar Messages

  • U430 Touch Screen Hinge Issue

     
    Hi,
    I have U430 Touch Screen Hinge issue, but lenovo service agents are not responding even if I give them the reference of below forum. Can you please help me resolve this issue as the laptop is under warranty (bought on december 2014)and it was not damaged. It was used last night and then just closed and kept on the bed. When I returned and tried opening it, I had this hinge issue. Please help me get this issue resolve at once.
    https://forums.lenovo.com/t5/Lenovo-U-and-S-Series-Notebooks/U430-Touch-Screen-Hinge/td-p/1809492/highlight/false
    Link to image
    Moderator note: large image(s) converted to link(s):  About Posting Pictures In The Forums

    Hi, This is the third time I called them but they are persistent that it is not cover under warranty for U430T. I do understand that if it is an accidental damage then it will not be covered. But my point is, from my end, there was no damage on the laptop and simply closed it and tried opening it after a while caused it. Furthermore refering to the post link, it is mentioned by Amy Tuper that if it is under warranty and cause is not by damage contact support. It is also mentioned that Lenovo launched an investigation in which it was concluded that there was mount failure on this model. So, my question is, isn't there a possibility that this defect could have been the mount failure issue ? Last call, they state that it is just for U530T even when the post says it is for both U430T and U530T. People on the same post have posted that they got it repaired by Lenovo for free. I am not sure what to believe, the post posted by Lenovo or the support service ? Can you please escalate the issue as it is hampering my day to day work. Awaiting reply from your end.   

  • U430 Touch Screen not working on Ideapad

    I just bought a new IdeaPad U430 laptop a few days ago and I love it. However, the touch screen doesnt work. I've looked through the forums and have tried a lot of things and none of it has helped so far. Using the f6 key on the laptop freezes the mouse but the touch screen doesnt seem to recognize my finger. Please help! Like I said, I love everything else about this laptop and I really dont want to return it.
    Moderator Note; subject edited; system type added

    hi graceella,
    Welcome to the Lenovo Forums.
    Ideally, the OS automatically identifies if you have unit with a Touchscreen or not. To check, look under Control Panel (large icon view) > System (see images below).
    Non-Touchscreen:
    - Link to picture
    - Link to picture
    Touchscreen:
    - Link to picture
    If the machine is showing No Pen and Touch Input:
    1. The OS is not identifying the screen as Touch capable. To isolate, perform a System Recovery (via the OneKey Recovery button) to check if the issue is on the OS level (ensure you backup important files first).
    If the machine is showing Limited Touch Support:
    1. Recalibrate or Reset the touchscreen
    2. Reconfigure the Touchscreen
    If same problem,
    3.  Press the Windows key‌ +R, type devmgmt.msc and press Enter.
    4. On the device manager, navigate to Human Interface Devices and uninstall anything that says HID-compliant device. When finished, reboot the system and observe.
    5. After the reboot, press Windows key‌ +R, type mspaint and press Enter. On mspaint, try to touch the screen and observe if the touchscreen capability is working.
     - Link to picture
    If the above steps doesn't resolve the issue, I recommend you contact Lenovo and report the problem (or the place of purchase if it's still possible to exchange the unit).
    Regards 
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Cleaning U430 Touch Screen

    I'm wondering if anybody knows how I can clean my U430's touch screen. I love the thing and I use it so much it gets very dirty!
    Thanks in advance!
    Solved!
    Go to Solution.

    Hi DesertFox899,
    Welcome to Lenovo Community Forums!
    Still Microfiber for Glass Panels/Touch Screen.
       I would Suggest this Product from Antec
    http://www.amazon.com/Antec-XL-Microfiber-Cleaning-Cloth/dp/B00584WZKG
    Just wipe the screen gently not applying too much pressure and the smudges should come off.
    Hope this helps
    Cheers!
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Ideapad U430 touch screen not working

    Dears,
    I have an ideapad U430 with windows 8 installed! the touch screen suddenly stopped working! please advise on what needs to be done 
    Thanks,
    Khaled

    Hi Khaled,
    Please perform the display driver and let me know the findings.
    Hope to hear back soon
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • U430 Touch Screen Hinge

    I got the Lenovo U430 Touch in late August and have noticed that the screen hinge wasn't very sturdy but it was still working fine. But today the hinge is broken and I can't close the screen properly without adjusting it. I didn't drop it or damage it and I looked it up and saw that other people were having similar issues and saying it was a production failure. Is there anyway I can get a replacement or do I have to send it in for repairs? I'm in college and I'll be needing it for a couple more weeks so I can't send it in for repairs yet. And is the $99 fee not covered by the warranty? I called Lenovo support and they said they can't look at my laptop until I pay the fee. I feel like the quality of Lenovo has declined recently. Any help would be appreciated.

    This just happened to me this morning! For those of you that were working with it broken for a while...did the break impede your daily use in any way beyond the inconvenience of the hinge function? I'm teaching in Romania right now (ironically, I bought this model specifically so it would be easier to travel with) and won't be back home in the U.S. for over a month so I can't exactly send it to be fixed right away. Am I going to damage it further if I keep using it? Edit: I'm also out of warranty, AND I noticed a month or two ago that my screen stop auto-rotating whenever I tried to flip it (which wasn't often at all, so I still don't know why my hinges would break so suddenly). Am I going to end up paying for these repairs? 

  • Lenovo U430 touch screen screen crack in just 6 months?

    Hi! I brought my lenovo 6 months ago and my experience was very bad.... 
    After i tink around 2 months. Whenever i open up my laptop, there is like a crack sound. I couldnt see anything visable until yesterday when the bottom of the screen just pop out. 
    I went to the service center and was told this is not covered in the warrenty and he was sure I had drop it before to have such a problem. 
    However I AM 100% SURE i have not drop my laptop before. My previous 2 computer could use for 5 and 4 years respectively but this lenovo brand computer that i tried is a disappointment. 
    I was told the estimated cost is around $300 if i would have to repair it and it would take 1 month to fully fix it. 
    I am a student. I have many upcoming projects to finish. Do you think i will have 1 month to fix this problem. And that $300 is just too much.
    I am pretty sure it is the quality of the laptop since i have NEVER drop it before. Although i close and open the laptop many times due to the need to travel between school and home almost everyday, isit that what a laptop is for to be portable?
    Please find out for me what can I do with this problem or are there any cheaper alternative out there since i am not that rich to just throw away my money for this.

    I need to gather several customer-provided photos of hinge mount failures on the U430 Touch model.
    If you could, it would really help me if several people could provide photos. (Please resize photos to make them smaller before posting.)
    Thank you for your help,
    Amy Tupper
    Technical Resolution Lead, Pervasive Issues
    Lenovo US
    ThinkPad T431s, S3 Yoga 14, Helix, Edge 11 & 14, E431, IdeaTab A1107, IdeaPad A1-07, IdeaCentre Horizon, Yoga Tablet 2 10 1051
    First computer was a 1980 Commodore 64 from Radio Shack/ GEnie SFRT member from 1993-1996

  • U430 touch screen issue

    the screen on my laptop just went white and then changes to red/green/blue then white and it keeps going.. 
    restarting the laptop doesnt fix the issue.. when it happened i didnt nottice any type of overheating
    since i always keep it on top of a cooling pad with fans on ..  
    laptop is out of warranty .. is this a known issue??  any troubleshooting procedures i should try?? i wanto to know if
    the problem is with the screen or the graphics card... 
    thank you for your time
    Solved!
    Go to Solution.

    Ashwin_Lenovo wrote:
    Hi Tomriddle,
    Welcome to Lenovo Community!
    As per the query we understood that you are facing issues with white screen in your Lenovo U430 laptop.
    Try to connect an external monitor and check for the issue, also try to move the laptop lid back n forth.
    Also try to update the graphic driver and check for the issue.
    Click here for the driver for windows 7.
    Click here for the driver for windows 8.
    Click here for the driver for windows 8.1.
    Hope this helps. Do post back if the issue persists!
    Best regards,                                                          
    Ashwin. S
    Thank you for you fast response.. 
    Here's what i did.. 
    1..  powered on / off the device multiple times without any luck
    2.. plugged my externeal monitor to the hdmi port... external monitor worked perfectly so i followed your advice...
         however the drivers i had installed were newer than the ones provided by the lenovo download site.. but i still
         "downgraded" the drivers to the ones you provided in your link.. rebooted. no luck ..  updated them to the newes
         ones found on windows update... rebooted.. no luck ..  at this point i was about to give up.. 
    3.. opened up the laptop and unplugged/ plugged the screen connector and turning on the laptop.. no luck..
    4.. unplugged / plugged the bios battery on the mother board.. no luck
    5.. unplugged / plugged the laptop battery connector and the bios battery ... no luck
    6.. unplugged the hard drive and booting up the laptop without it... no luck so i plugged it back in
    7.. remove the memory stick and booting up the laptop without it .. screen wouldnt even light up (power button shows it was on.. and the keyboard light went on and off like it does when it boots up.. -- something for a change!!
    8.. reinstalled the memory stick and booting up the laptop.. still the same thing.. white screen followed by red.. green.. blue.. no luck
    9.. i didnt have a direct replacement of the PC3L memory stick but i did have a DDR3 PC3 memory stick in another laptop..  some google search and found that as long as theyre both DDR3 PC3 they should be compatible .. so .. i  replaced the memory stick.. booted up the laptop.. screen wouldnt even light up ..
    10.. replaced the memory with the original stick.. before quiting i decided to give it another try before plugging in the hard drive...  and ...  IT WORKED..  however since the hard drive was unplugged it went to the no booting device and bios screen..   
    11... powered off the laptop... plugged in the hard drive...  (started praying) .. turned it on.. and it worked... 
    12... powered it off.. screwed the back cover on ..  powered it back on...  and its working fine so far.. played some video.. rebooted a couple times without any issues..
    i do not know if there whas a "current state" flag or data saved on the ram or if it was caused by the UEFI system.. 
    but i guess after replacing the memory stick it cleared up or something that when i replaced it back i booted up from scratch refreshing the devices or i have no idea.. but it works now .. 
    hope this helps someone in the future.. .. again thank you for your time!! 

  • I dont know how to get to the touch screen settings because the touch part(not screen) wont let me. it lets me drag to the stuff and some lady says something in the earphones

    i really need help

    Sounds like VoiceOver has been enabled. See this article for instructions on turning it off.
    iPod nano (6th generation and later): How to use VoiceOver
    B-rock

  • Magnification Software for Touch Screen POS softwares

    Hi,
    I am legally blind and trying to open a Jimmy Johns restaurant.  I have ran into some problems due to the POS systems that PDQ signature Systems uses.  They utilize POSReady and have notified me
    that there are no options for magnification software.  I am looking for a magnification software that would be similar to
    that of what is used on Windows 7 & 8.  I do have a link that shows that there are accessibility options for the blind with POSReady.  
    Can anybody provide details of magnification software that could be used for a touch screen POSReady system?
    Thank you.  

    The accessibility options in POSReady 7 are the same as those in Windows 7. It is up to the manufacture to install these features.
    www.annabooks.com / www.seanliming.com / Book Author - Pro Guide to WE8S, Pro Guide to WES 7, Pro Guide to POS for .NET

  • Pantech Hotshot - touch screen buttons activated by cheek

    I am having tons of frustration using the Pantech hotshot.  When I'm talking, the Mute, Speaker Phone, Bluetooth, etc. buttons seem to get activated because of the proximity of the phone to my face.  Often I'm answering the phone in a noisy area and need to hold it close.  Is there any way to adjust the phone's touch sensitivity?

        We want your handset to function as conveniently as possible for you webbyW! You can definitely adjust the touch screen settings on your Hotshot. I have included a link for your reference. I hope this information was helpful.http://bit.ly/K7Z0Q0
    Sincerely,
    JonathanK_VZW
    VZW Support
    Follow Us on Twitter@VZWSupport

  • HT3775 I NEED I TUNES FOR A 64 BIT PC. OPERATING SYSTEM IS WINDOWS 8, NON TOUCH SCREEN. WHICH IS THE ABSOLUTELY BEST WAY TO GET ITUNES OPERATING CORRECTLY ON MY PC????//I HAVE TRIED SEVERAL THINGS, NONE OF WHICH ARE WORKING. IS ITUNES DELIBERATELY EXCLUDI

    I cannot get itunes to work/install on myPC. I am running windows 8 in a 64 bit machine. I also want to purchase books via itunes for my Nook. Are you deliberately excluding PC owners so we cannot use ituens on our computers???? I have selected a community but have no idea what community I should be working with. Can somone explai these communities to me? Also. you don't allow much time to go thru the sign up process. I had to start over SEVERAL times as you kept timing me out. Jesus...when people are signing up for the first time, we have no idea of the questions that will be asked. Give us a break and give us time to sign up. Not everone is disability free and able to go thru your process quickly...you are NOT user friendly. You should be for people who are wanting to join your community. I used to want an Apple product but now that  I have had first hand experience with your web page, I think I will probably stay away from Apple products. VERY DISAPPOINTING

    Jan 11, 2014 10:26 AM  Re: I NEED I TUNES FOR A 64 BIT PC. OPERATING SYSTEM IS WINDOWS 8, NON TOUCH SCREEN. WHICH IS THE ABSOLUTELY BEST WAY TO GET ITUNES OPERATING CORRECTLY ON MY PC????//I HAVE TRIED SEVERAL THINGS, NONE OF WHICH ARE WORKING. IS ITUNES DELIBERATELY EXCLUDING
      Re: I NEED I TUNES FOR A 64 BIT PC. OPERATING SYSTEM IS WINDOWS 8, NON TOUCH SCREEN. WHICH IS THE ABSOLUTELY BEST WAY TO GET ITUNES OPERATING CORRECTLY ON MY PC????//I HAVE TRIED SEVERAL THINGS, NONE OF WHICH ARE WORKING. IS ITUNES DELIBERATELY EXCLUDING PC'S  in response to Birdlover1      
    Post over in the iTunes for Windows forum, here:
    https://discussions.apple.com/community/itunes/itunes_for_windows
    sebastian

  • Keyboard Marks on Laptop Screen, Do I Need a Cover for my U430 Touch?

    I was online recently and noticed some ultrabook users talking about how having their ultrabook in a bag with a lot of other things had pressed the keyboard of it against the screen, creating stain marks. I'm a bit concerned this might happen with my U430 Touch as I will be keeping textbooks in with it, however, they will be behind it, but will be seperated by a thin layer of the bag. Has anyone heard of this happening and should I invest in a keyboard cover sheet in order to prevent this? 
    Thanks in advance!
    PS: I love the U430 Touch, GO LENOVO!!!
    Solved!
    Go to Solution.

    Hi DesertFox899,
    Welcome to Lenovo Community Forums!
    As per the issue you have provided if the laptop is pressurized in the bag and as it is a touch screen model there might be chances of keyboard marks, I would suggest you to use a keyboard protection to avoid the further damages.
    Do post us back for further queries.
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Touch screen not working after system update

    A few months ago, my laptop (Satelitte P55t-A5202) went through an automatic system update.  Ever since then, my touch screen won't work.  I followed the directions to reinstall the HDI programs several times.  The first time it worked but only for a few hours. The next time I tried to reinstall, it worked for a second.  Now reinstalls do nothing. 
    Before the system update, my touchscreen worked fine.  And in reading the forums, this seems to be a common problem with the updates.  I called TOSHIBA customer service for help.  The FIRST thing they want to do is charge me for tech support because my laptop is out of warranty.  I told the customer service rep repeatedly that my touch screen worked fine until the update.  He refused to give me any help because I did not want to pay for him to tell me how to resolve...
    In my opinion, this is a toshiba issue not mine so regardless if my laptop is out of warranty, Toshiba should take ownership and be accountable for the problems they cause.
    Does anyone have any suggestions as to how to take care of this?
    By the way, Toshiba customer service representative was rude, you could barely understand him because of his accent, I had to repeat SEVERAL times what my issue was because he couldn't get past the warranty issue and I had to ask several times to speak with a supervisor ( to which he told me a supervisor would call me instead)

    See my reply in the laptop forum.
    -Jerry

  • I cannot use the bottom part of my touch screen. It would not respond to any of the touches I make. Is the screen broken or have I stuffed up my settings? I want to be able to type on my iPhone

    I cannot use the bottom part of my touch screen. It would not respond to any of the touches I make. Is the screen broken or have I stuffed up my settings? I want to be able to type on my iPhone

    Basics from the manual are restart, reset, restore from backup, restore as new.  If you've been through ALL these steps and you still have the problem, you'll need to bring the phone to Apple.

Maybe you are looking for

  • Webutil Host bean error

    I'm trying to use the webutil.nonblocking procedure, i followed all the steps in the user guide to install the webutil and i attached the library to the form and subclassed the object group, but when running the form i receive this error oracle.forms

  • Audio is Out of Sync on NTSC Preview Monitor

    Hello FCP Gurus, I recently was hired by a local Broadcast TV Affiliate and I am looking at their FCP systems. I noticed that one of the suites has a big problem with the NTSC Preview Monitoring, the audio is way out of sync. Here's the set up: G5 Du

  • My IMAC will not boot to Windows Vista

    I can not get my IMAC to boot to Windows Vista.  I restart the computer, hold the option key, and it keeps getting hung up on the blank white screen that comes up when you first turn the computer on.  It just sits on this screen forever and never pul

  • Need help creating PDF w/ comment tools available in Reader!!

    I'm trying to create a PDF that you can use the "comment" and other proofing tools in Reader. I've tried using Acrobat Pro to adjust the settings so the "comment" and other tools are available in Reader but it isn't working. Here's what I'm really tr

  • Hot spot in Bar chart

    Hi,     I have a requirement where I need to maintain hotspot for the graphical bars of the barchart. How can it be accomplished. There is a standard demo program BARCBO02 for Barcharts, but hotspot is not provided. Please let me know how it can be a