Unable to connect via RDP 5.2 when multiple RDP-TCP connection setup with NLA disable

Hi All,
Need help urgently, I had setup a multiple RDP-TCP connection for separate RDP connection with different IP.
Problem I face after setting up multiple RDP-TCP connection, the old version of RDP 5.2 non longer working even with NLA disable. RDP 6 and above no problem connecting to the RDP session.
Error message on RDP 5.2 shown as:
"Because of security error, the client could not connect to the remote computer. Verify that you are logged on the network, and then try connection again."

Hi,
Please try the steps in the article below and see how it works.
Because of a security error, the client could not connect to the Terminal Server
http://support.microsoft.com/kb/329896
Thanks.
Jeremy Wu
TechNet Community Support

Similar Messages

HT4199 my wifi is not connected on my iphone and when i try to connect it does not recognise my password

my wifi is not connected on my iphone and when i try to connect it does not recognise my password

Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.

HT1212 IPAD is Disabled, tried to connect via itunes but get error "iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."

IPAD is Disabled, tried to connect via itunes but get error "iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."

iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

I found my old ipod touch and it says the ipod is disabled and to connect it to itunes but when i try to connect it to itunes it says cannot connect cause ipod has passcode but i cant unlock passcode cause ipod disabled. Please anyone have an idea?

I found my old ipod touch and it says the ipod is disabled and to connect it to itunes but when i try to connect it to itunes it says cannot connect cause ipod has passcode but i cant unlock passcode cause ipod disabled. Please anyone have an idea?

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...

WRT160n v3 has slow connection when multiple users are connected

As of last night my router has been producing slow connectivity when multiple users are connected to it, but it's perfectly fine when only one user is connected.
I am on a laptop myself, but we also have a second laptop and a desktop where the modem and router are set up.
I have upgraded the firmware so that is up to date.
We have Comcast Fiber Optics so my internet speed is normally quite fast even when all of my computers are connected.
Some settings that I have that might help resolve the issue:
I am using DHCP Configuration.
My Channel Width is set to 20 MHz and I am using Channel 11.
The Security Mode is set to WPA Personal. I had it on WPA2 Personal but I read that changing to WPA Personal might help and so far it doesn't seem to have done anything.
I set the Beacon Interval to 50, Fragmentation Threshold to 2304, and RTS Threshold to 2304.
Everything else is set to the default factory configuration.
Just today I received a notice that said "Windows has detected an IP Address Conflict", but ever since I reinstalled the Firmware it hasn't come back. I've rebooted both my laptop and the desktop to confirm it hasn't come back as well.
I consider myself to be computer savy, but I just can't figure out what the problem is as I've tried everything that I could think of including reconfiguring my router and restarting my modem as well. This problem has presented itself in the past before but unfortunately I cannot remember what I did to fix it.

Try using inSSIDer to help you find the best channel.
http://www.metageek.net/products/inssider/
If that doesn't help, you can try disabling WMM.
Edit: You should use WPA2 AES security for best performance.

My MacBook isn't connecting to the Internet. When I try to connect, it shows the signal strength in the top right corner as if it was connected, but the Internet doesn't work. When I go to my network preferences, it says the ip is self-assigned.

My MacBook won't connect to the Internet, but it's connected to my router. When I go to network preferences, it says that it has a self assigned ip address, and can't connect to the Internet. How can I fix this? Please help!

First thing you need I think is to get your iMac connected to the Internet.
Shut down your iMac and you iPad. Then power off your router. Wait 30 seconds and power up the router.
After the router indicates that it is connected to the Internet then start up your iMac and see if it connects. If the iMac connects to the Internet then your iPad should too.
If this power up sequence doesn't work you'll have to dig into the router setup to make sure it is working properly.

I lose my internet connection on my XP computer when the printer is connected as wireless.

My new hp6510 wireless printer works great but I lose my internet connection when the printer is connected as wireless. I am using the printer with a linksys router E3000. The network has an XP computer , a win7 64 bit computer. I do not have a problem with the win 7 computer, but the xp computer will drop the internet connection and sometimes I can get it to work by repair of the router connection, but sometimes I will need to reboot the computer. If I stop the wireless connection and use the USB it works OK. I have tried to get help from HP and Linksysm but no help. I would appreciate any suggestions.
This question was solved.
View Solution.

Hi,
Please try the following workaroud and let me know of any change:
From the PC's Desktop, click the HP Photosmart 6510 icon.
Under Printer Preferences, click Estimated Ink Levels.
Click the Advanced Settings tab.
Under Show Alerts, mark the 2nd option - Only show me ink alerts when I print.
Click Close, reboot the PC and follow for any change.
Please let me know of any progress,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Connect to one wireless network when multiple networks with the same name

Hi all,
I'm at a location where there are two networks with the name (e.g.) "wireless". One uses WEP and one uses WPA. The WEP network is weaker than the WPA network, so my Mac tries to connect to the WPA network, even though I have manually setup the wireless network with WEP security (after trying to connect it asks for a WPA password). Is there a way that I can connect to a wireless network by MAC Address, or some way for me to tell the Macbook to ignore the WPA network? The problem is that the SSID is the same, it seems.
Thanks,
Nate

The person (the landlord) isn't tech-savvy at all.
That is clearly obvious as
1. They would not be using WEP
2. They would setup a different SSID
WEP is not secure and can be cracked in minutes using tools readily available on the internet. If a hacker gain access to that network they could run other tools and hijack the dns and then you could be visiting sites on your mac that are completely bogus but look real.
Also it is common trick that hackers use is to setup an access point nearby with the sane SSID to capture details from users that join their network thinking they have joined their own network. Again the hacker can hijack the dns and monitor all your browsing and capture details.
The fact that someone has setup an SSID nearby with the same name would make me very suspicious.
I would treat your landlord's network as an untrusted network same as when your using a public wifi like coffebucks.

ITouch only connects to Wi-Fi conflicts when the laptop is connected

When the laptop is connected to the WLAN the iTouch connects and browses with no problem at all. Problem is that when the laptop is NOT on oe NOT connected the iTouch WILL see the wifi signal but refuses to connect. this is obviously a major pain. My friends iPhone finds and connects to the home network without issues - ie regardless of whether the laptop is on or off.
can anyone suggest a remedy? My iTouch is only 24hrs old!
thanks in advance, DM

Here's what's happening in my case. I have a siemens se567 router. I have a LAN with three computers using it. It's encrypted WEP64 bit. Everything is working fine except the new itouch. It connects, shows a strong signal, but won't allow the browser to connect to the internet. It do not have numbers under the DNS or the router. The Apple people I have spoken to tell me it's the router, and to talk to my adsl provider. The adsl provider tells me it's an apple software problem, they can't help. I can connect to any unencrypted wireless network. I can't even manually put in the router numbers. I have unplugged the router several times, but this doesn't help. I'll try your suggestion for "other" and see if that works. Thanks.

I sometimes get Error 42 when opening a TCP connection - how can I fix this ?

In my Labview application I am opening a TCP connection in an identical way to the Data Client example. I am using a direct connection to external equipment using an ethernet crossover cable. The error occurs on at least 2 different PCs.
The error can occur regardless of whether anything is connected to the ethernet port of the PC.
The only way I have found to clear the error is to power down the PC and restart with a connection to the office LAN. Then I can swap back to the crossover cable and talk to the remote equipment once again, ...unitl the next time the error occurs.
I have LabView 6.0 running on Win98.
Any help greatly appreciated.

Jeremy,
Thanks for taking the time to answer
I already checked the link you suggested but I am connecting to my remote instrument with a 2m cross-over cable.
I Have looked into this a little further, it seems the sequence of events is as follows -
1. After some hours the connection gets lost.
2. TCP Read returns error 66 - Connection was closed by peer.
3. If I try to restart my program I get Error 42 at TCP open Connection.
4. Rebooting the PC doesn't clear the error 42 problem.
5. If I try to PING my instument I get "Host unreachable".
6. I have to "refresh" my network card by connecting to our LAN and either opening a file on another PC or simply sending a PING to another PC.
6. I can then reconnect my remote instrument via cross-over cable
and we're up and running for another few hours.
I get the same problem on two different PCs with different NICs and different OS (Win98 and WinME)
I am assuming that because a reboot has no effect that its not a memory allocation problem.
It seems like LabView stops talking to the NIC and then gets locked out some how.
Any other tips ?

I have my IPod Touch connected via USB but it says it's not connected to my computer

I have my IPod Touch connected VIA USB port but a message tells me it's not connected to my computer so I can't get mail, etc. What do I have to do to remedy this?
Thank you.
Rjhs

What is the exact wording of the error message?
What are you trying to do?
The USB connection provides not internet connectivity. The iPod can only connect to the internet via wifi

I recently noticed that the light on the magnetic connection is always on even when it's not connected to the computer. I keep it plugged into the wall but I don't think the light was always on like that before. Is there something wrong?

I recently noticed that the light on the magnetic connection to my charger for my laptop is always on even when it isn't connected to the computer. I keep it plugged in. I don't remember it being like that in the past so I'm wondering if something is wrong.

Last sentence in the paper suggested by DALE:
Additional Information
Whether your product is in or out of warranty, you can take your adapter to an Apple Authorized Service Provider or Apple Retail Store for evaluation and replacement if necessary. Pending the results of the evaluation, you may or may not be eligible for a replacement adapter free of charge. Signs of accidental damage would negate any coverage. Be sure to bring in the computer used with the adapter; it is required to process potential adapter replacements.

My ipod says Ipod disabled connect to itunes. But when I try to connect to itunes it says I have to enter the passcode on the ipod to use itunes...any help?

Ipod screen says Ipod disabled connect to itunes...but when I connect to itunes it says ipod is passcode protected and I must enter passcode on my ipod to continue. But I cant enter the passcode becaue the ipod is disabled. Brothers entered a bunch or wrong passcodes to disable so I couldn't play it.

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

RDP session freeze when resizing RDP window

Hi
since last week friday a user reports a freezing RDP session when he resize the RDP window (to move the session window to another screen (PC has 3 screens connected)) of a . The RDP target is a windows 2008 R2 RDS. Last Friday there were many MS updates
installed on this PC.
I determined that the issue must be related to the PC, if user connects from another PC to RD-Server the problem doesn't exists. But i have no starting point to search for the reason. There are no warnings or errors in local eventlog. RDP connections to
another RD-Server work fine.
Any hint where to start to solve this issue?
Regards Carsten

Hi Carsten,
Thanks for the reply.
It seems that the user has updated his RD client to RDP 8.0. If so, please note that Aero Glass is not supported.
Description of the Remote Desktop Protocol 8.0 update for Windows 7 SP1 and Windows Server 2008 R2 SP1
http://support.microsoft.com/kb/2592687
Thanks.
Jeremy Wu
TechNet Community Support

Connected Apple TV Box tonight and it said it needed an update. I ran the update, and it worked for a few minutes. Then all of a sudden, a screen popped up showing that I needed to connect via USB plug to my MacBook Air to connect to iTunes. Why??

I conneced the Apple TV and it worked fine at first. It has worked well for some time. We are using them in our school this year, as well as converting to all apple products. I have been able to pull up my computer screen through Apple TV onto our projectors. However, tonight when I started apple TV, the mirroring icon came up, and everything seemed fine. Then a message came up that the Apple TV Box needed an update. I clicked on the button to run it now, and it seemed fine. The mirroring worked for about 5 minutes after the update, then I got a screen that had a picture of the Apple TV Box and a USB cord directed toward a picture of the iTunes icon. The light on the frontof the component flashed, and I couldn't go to the menu at all. I wouldn't do anything. I no longer cold see the Airplay/mirroring icon on my computer either. I tried to shut everything off and reboot the computer and the Apple TV box. However, none of this worked.
Any suggestions??? I'm a high school football coach, and this is how our team will watch film this year. I really need to get this rectified by the end of the week, as our team will go into camp for the next two weeks.

Hello Philly,
I believe that when you reset your ipod(command given from the computer, right?) touch WHILE the ipod was updating, It cleared the system in the middle of writing files, thus corrupting(equivalent of cutting of in the middle of a sentence) the basic running system.
I suggest you go to an apple store and ask for a technical diagonosis in person. they may offer to help if the problem is fixable. If your ipod is still under warrenty, i would guess it would be free/low cost.
~Remember, I am just giving an educated guess on limited information

Unable to connect via RDP 5.2 when multiple RDP-TCP connection setup with NLA disable

Similar Messages

Maybe you are looking for