Unable to get 1920x1080 resolution [Solved]

I am trying out a Philips 24" LCD monitor, capable of 1920x1080 at 60Hz. My graphics card is an nVidia FX-5600DT and I am using the nvidia-173xx driver. At present I can only get 1280x1024.
Here is my xrandr output:
Screen 0: minimum 320 x 240, current 1280 x 1024, maximum 1280 x 1024
default connected 1280x1024+0+0 0mm x 0mm
1280x1024 50.0*
1280x960 51.0
1024x768 52.0
896x672 53.0
800x600 54.0 55.0
640x512 56.0
640x480 57.0 58.0
512x384 59.0
400x300 60.0
320x240 61.0
Here is my xorg.conf file where I have attempted to force 1920x1080:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Sun Nov 8 21:50:38 PST 2009
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "extmod"
Load "glx"
Load "dbe"
Load "dri2"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 30 - 83
VertRefresh 56 - 75
Modeline "1920x1080_60.00" 172.80 1920 2040 2248 2576 1080 1081 1084 1118
Option "PreferredMode" "1920x1080_60.00"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "NV31 [GeForce FX 5600]"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
And here is my Xorg.0.log output:
Current version of pixman: 0.16.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Feb 10 12:11:30 2010
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(==) Automatically adding devices
(==) Automatically enabling devices
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) Loader magic: 0x81e4c60
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(++) using VT number 7
(--) PCI:*(0:1:0:0) 10de:0312:147b:8f19 nVidia Corporation NV31 [GeForce FX 5600] rev 161, Mem @ 0xde000000/16777216, 0xe0000000/268435456, BIOS @ 0x????????/131072
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded by default.
(II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 173.14.22 Sun Nov 8 21:42:44 PST 2009
(II) Loading extension GLX
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) NVIDIA dlloader X Driver 173.14.22 Sun Nov 8 20:43:40 PST 2009
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules/libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.7.3.902, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0): enabled.
(II) NVIDIA(0): NVIDIA GPU GeForce FX 5600 (NV31) at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 262144 kBytes
(--) NVIDIA(0): VideoBIOS: 04.31.20.38.00
(II) NVIDIA(0): Detected AGP rate: 8X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce FX 5600 at PCI:1:0:0:
(--) NVIDIA(0): Philips 244E (DFP-0)
(--) NVIDIA(0): Philips 244E (DFP-0): 140.4 MHz maximum pixel clock
(--) NVIDIA(0): Philips 244E (DFP-0): Internal Dual Link TMDS
(II) NVIDIA(0): Assigned Display Device: DFP-0
(WW) NVIDIA(0): No valid modes for "1920x1080"; removing.
(WW) NVIDIA(0):
(WW) NVIDIA(0): Unable to validate any modes; falling back to the default mode
(WW) NVIDIA(0): "nvidia-auto-select".
(WW) NVIDIA(0):
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "nvidia-auto-select"
(II) NVIDIA(0): Virtual screen size determined to be 1280 x 1024
(--) NVIDIA(0): DPI set to (62, 89); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(==) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) NVIDIA(0): Initialized AGP GART.
(II) NVIDIA(0): Unable to connect to the ACPI daemon; the ACPI daemon may not
(II) NVIDIA(0): be running or the "AcpidSocketPath" X configuration option
(II) NVIDIA(0): may not be set correctly. When the ACPI daemon is
(II) NVIDIA(0): available, the NVIDIA X driver can use it to receive ACPI
(II) NVIDIA(0): events. For details, please see the "ConnectToAcpid" and
(II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
(II) NVIDIA(0): Config Options in the README.
(II) NVIDIA(0): Setting mode "nvidia-auto-select"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(==) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(WW) NVIDIA(0): Option "PreferredMode" is not used
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing extension GLX
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.3, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device Logitech USB Receiver
(**) Logitech USB Receiver: always reports core events
(**) Logitech USB Receiver: Device: "/dev/input/event5"
(II) Logitech USB Receiver: Found 12 mouse buttons
(II) Logitech USB Receiver: Found scroll wheel(s)
(II) Logitech USB Receiver: Found relative axes
(II) Logitech USB Receiver: Found x and y relative axes
(II) Logitech USB Receiver: Found absolute axes
(II) Logitech USB Receiver: Found keys
(II) Logitech USB Receiver: Configuring as mouse
(II) Logitech USB Receiver: Configuring as keyboard
(**) Logitech USB Receiver: YAxisMapping: buttons 4 and 5
(**) Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
(**) Logitech USB Receiver: (accel) acceleration profile 0
(II) Logitech USB Receiver: initialized for relative axes.
(WW) Logitech USB Receiver: ignoring absolute axes.
(II) config/hal: Adding input device Logitech USB Receiver
(**) Logitech USB Receiver: always reports core events
(**) Logitech USB Receiver: Device: "/dev/input/event4"
(II) Logitech USB Receiver: Found keys
(II) Logitech USB Receiver: Configuring as keyboard
(II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event3"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
Note "(WW) NVIDIA(0): No valid modes for "1920x1080"; removing." from the log. How do I somehow ensure a valid mode? Any other ideas appreciated.
Larry
Last edited by lagagnon (2010-02-11 00:00:30)

Maybe under "Screen" put a virtual resolution, like:
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x1024"
Virtual 1920 1080
Sorry if you tried this already or isn't what you want. I just remember having this issue on a desktop I used to have (although I no longer have it), and had nVidia graphics that for some reason wouldn't allow the resolution I wanted so I plugged in Virtual and it worked. Probably not the most elegant ways to achieve it but it worked for me and I didn't see any problems. Anyway, worth a try.

Similar Messages

I recently upgraded my iphone to the latest IOS but my GPS seems to have a problem... I am unable to get directions from one point to another ... how do I solve this problem?

help! I recently upgraded my iphone to the latest IOS but my GPS seems to have a problem... I am unable to get directions from one point to another ... how do I solve this problem?

If using the built-in Maps app, directions are not available everywhere. Read here:
http://www.apple.com/ios/feature-availability/#maps-directions
If that's your problem, download the Google Maps app.

HT5019 unable to get turn on display after turning on the power button ,no caps lock is turning on too,even a light at unlock button to open display is not going down , mine was a late 2008 mac book pro ( 17 inch ).please help me to solve my problem

unable to get my screen on even after turning on power button .
light at display unlock was not going down ,
no caps lock button turning on .
please help me to rectify my problem apple community

unable to get my screen on even after turning on power button .
light at display unlock was not going down ,
no caps lock button turning on .
please help me to rectify my problem apple community

Unable to get SQL Server Agent to run after installing SQL 2012 Standard with SP1

I am unable to get SQL Server Agent to run after installing SQL 2012 Standard with SP1. Log message is as follows:
Attempting to load library 'xplog70.dll' into memory. This is an informational message only. No user action is required.
Failed to verify Authenticode signature on DLL 'C:\Program Files\Microsoft SQL Server\MSSQL11.MSSQLSERVER\MSSQL\Binn\xplog70.dll'.
Error: 17750, Severity: 16, State: 0.
Could not load the DLL xplog70.dll, or one of the DLLs it references. Reason: (null).

Hi JFriedley,
According to your error message, there might three reasons for this issue.
xplog70.dll is corrupt, you need to check if you have any SQL Server running on same file version and same production
edition. If xplog70.dll is corrupt, you can copy it from the new server where agent is running fine to your problematic server.
Native client not installed properly. If you try applying any latest Service Pack or Cumulative Update then check if the SQL Server Agent can start, if that also doesn’t solve issue then try to reinstalling SQL Server Native client from SQL Server setup
files.
There is a similar issue about error 17750, you can review the following article.
http://blogs.lostincreativity.com/sqldba/sqlserver-error-17750-could-not-load-the-dll-xpstar90-dll/
Regards,
Sofiya Li
If you have any feedback on our support, please click here.
Sofiya Li
TechNet Community Support

DropDrown unable to get data in ALV

Hi,
I'm trying to put an dropdown by key (or index) into an ALV but I'm unable to get data in the dropdown. Can someone please help me with this?
I was watching this threads on topics at the forum, but I can not solve this problem.
Copy my code.
DATA: lr_col                            TYPE REF TO cl_salv_wd_column,
             lr_dropdown                  TYPE REF TO cl_salv_wd_uie_dropdown_by_key,
             l_cmp_usage                TYPE REF TO if_wd_component_usage,
             l_alv_model                   TYPE REF TO cl_salv_wd_config_table,
             l_ref_interfacecontroller TYPE REF TO iwci_salv_wd_table.
l_cmp_usage = wd_this->wd_cpuse_doc_measure( ).
IF l_cmp_usage->has_active_component( ) IS INITIAL.
    l_cmp_usage->create_component( ).
ENDIF.
l_ref_interfacecontroller = wd_this->wd_cpifc_doc_measure( ).
l_alv_model = l_ref_interfacecontroller->get_model( ).
l_alv_model = l_ref_interfacecontroller->get_model( ).
l_alv_model->if_salv_wd_table_settings~set_read_only( abap_false ).
lr_col = l_alv_model->if_salv_wd_column_settings~get_column(
    id = 'VALEUR_DIFF' ).
CREATE OBJECT lr_dropdown
    EXPORTING
      selected_key_fieldname = 'VALEUR_DIFF '.
lr_col->set_cell_editor( lr_dropdown ).
DATA:
lo_nd_ctx_tab TYPE REF TO if_wd_context_node,
lo_ndinfo_ctx_tab TYPE REF TO if_wd_context_node_info,
lt_value_set TYPE TABLE OF wdr_context_attr_value,
ls_value_set TYPE wdr_context_attr_value.
ls_value_set-value = '01'.
ls_value_set-text = 'One'.
APPEND ls_value_set TO lt_value_set.
ls_value_set-value = '02'.
ls_value_set-text = 'Two'.
APPEND ls_value_set TO lt_value_set.
lo_nd_ctx_tab = wd_context->get_child_node( 'DOC_MEASURE' ).
lo_ndinfo_ctx_tab = lo_nd_ctx_tab->get_node_info( ).
lo_ndinfo_ctx_tab->set_attribute_value_set(
    name = 'VALEUR_DIFF' value_set = lt_value_set ).
DATA: lt_valueset TYPE TABLE OF wdr_context_attr_value,
            ls_valueset TYPE wdr_context_attr_value,
            lr_node TYPE REF TO if_wd_context_node,
            lr_nodeinfo TYPE REF TO if_wd_context_node_info.
lr_node = wd_context->get_child_node( 'DOC_MEASURE' ).
lr_nodeinfo = lr_node->get_node_info( ).
lr_nodeinfo->set_attribute_value_set(
EXPORTING
    name = 'VALEUR_DIFF'
    value_set = lt_valueset
Thanks.
Matías.

Hi,
In your code, you are trying to do set_attribute_value_set twice. If you read your code carefully, you are setting the values once using lt_value_set where you have correctly filled the values. But after this, you are again trying using lt_valueset without filling any values. This is why your previous value-list gets overwritten and you see nothing in the dropdown. Remove the following lines in your code and it will work fine.
DATA: lt_valueset TYPE TABLE OF wdr_context_attr_value,
ls_valueset TYPE wdr_context_attr_value,
lr_node TYPE REF TO if_wd_context_node,
lr_nodeinfo TYPE REF TO if_wd_context_node_info.
lr_node = wd_context->get_child_node( 'DOC_MEASURE' ).
lr_nodeinfo = lr_node->get_node_info( ).
lr_nodeinfo->set_attribute_value_set(
EXPORTING
name = 'VALEUR_DIFF'
value_set = lt_valueset
Please get back if you are facing any more issues.
Regards,
Nithya

Camcorder video error: "Unable to record. Resolution not supported by memory card."

We purchased two Samsung Droid Charges the first day they were released and recently they've both been getting this error after 8-15 seconds of recording in HD (1280x720): "Warning: Unable to record. Resolution not supported by memory card."
Called Verizon tech support, but they referred me to Samsung. Not knowing much about micro SDHC cards, I was alarmed to discover that the factory pre-installed 32gb card is only rated class 2 for speed. Samsung told me you need a minimum of speed class 4 or higher to record at this resolution. The only problem is you need an SD card installed in order to use the camcorder, period. In other words, all of us who payed an arm and a leg for the best phone Verizon sells now have to go buy our own micro sd card that actually supports all of the phone features as advertised?! The lowest prices I've seen for the faster cards are $70. Are we the only two Charge owners experiencing this problem? I've read somewhere that lower speed class cards may initially support faster speeds than they are rated until they accumulate more files, so the problem may go undetected for some time until you have more files that are stored in different locations on the card (making them difficult to access at the faster speeds). This may explain why are the first ones to get this error since we've had the phones the longest and only 50% free space remaining on the SD card. Oh, Samsung also said they won't be able to replace your card for one that has the proper speed rating. Kind of seems like false advertising to say a feature is available (HD camcorder), and then not mention the fact that the memory card provided isn't sufficient for that feature (separate upgrade required). Anyone else sharing the same frustrations? Ideas?

Thanks for the response. I've tried everything on that page. It's not an issue with the cable, or firewire port or the cable being connected properly, as the iSight camera works fine with iChat. I've disconnected the only other firewire device on the computer, didn't make any difference. Camera works fine in iChat, so it's not the camera itself. And, as I mentioned in the post, the same camera, if hooked up to my laptop, works just fine recording in QuickTime. So, it appears to be an issue with the QuickTime installation on this computer. I've done a search for the same error I'm getting and found some other occurrences with the same problems, but none that offered a solution.

New inst: HP-UX: db2icrt fails: CLP frontend unable to get request handle

We are migrating our installations from the beautiful AIX to ... HP-UX. I am told I will learn to love it, but probably not until they update df to at least 1988 levels.
This is the pilot install. We have never seen this work before (and maybe no-one has...?)
sapinst runs correctly up to the "Create database instance" phase. At that point it dies with the following:
FUNCTION: DB2 UDB, command line process, clp_start_bp, probe:3
MESSAGE : CLP frontend unable to get REQUEST handle
DATA #1: Hexdump etc.
DBI1281E: The database manager configuration file could not be read initialized.
No further useful information is provided.
In db2<sid> I have a bunch of dot files (.profile and the like) and the db2_software directory containing the database installation.
During the create database instance phase, I can see that directory sqllib is created, but it is deleted when the phase fails.
There is no litter of any kind in the /db2/<SID> directories, - nothing has been done at all.
I have done the following: <<imagine nice bullets below - they dont seem to be available here>>
checked that the permissions on /tmp and the installation direcctory (redirected by setenv TEMP /usr/sap/install) are 777: they are;
checked the OS parameters with db2osconf - they are good
checked the host name resolution with a perl script - gethostbyname and gethostbyaddr agree.
the ip address, simple hostname and FQDN are on a line in the hosts file
there is no litter from previous installations - this is a clean machine
I could not find any reference to required environment variables (such as LD_LIBRARY_PATH) in the install guide or the install note - so I have not set any.
I have been hacking away at this for days. I have put in a call to SAP, who will get back to me after dark (of course...)
This seems to be a massively popular problem, and the helpful error message ("Sorry, Sport, just can't bring myself to do it") seems to have people jumping from tall buildings and in front of busses all over Google-world. Furthermore there also seems to be a near-infinite number of possible causes and none of them seem to apply here.
H-PUX version is 11.31. DB2 is 9V5 patch 4. sapinst is latest available. Weekend is fading fast...
Edited by: Russell Day on Mar 5, 2010 7:46 AM

>
Paul Power wrote:
> Hi Russell,
>
> Apologies if some of this has been already tried but please check the following points:
>
> Make sure the machine name is listed in its hosts file.
>
> Make sure to log on directly to root. ie: do not su to root from another without '-'
>
> Make sure there is no instance created already (find / -name sqllib) for that user
>
> Using ps -aef and ipc -a, no old db2 ressources should be displayed for db2 instance owner. If there are any, kill/remove it
>
> You should make sure, that LIBPATH and LD_LIBRARY_PATH of root and db2 instance owner does not point to an path of another db2 version
>
> Regards,
> Paul
No need to apologise for assisting, Paul, but I have dealt with most of these.
The host file contains the unqualified and fully qualified hostnames, on the same line, unqualified first.
I am logging in as root (because there were no other users, and I'm old school, from when everyone logged on as root to do everything.
There is no instance, and in fact there is no sqllib except when the "create database instance" step is running.
The only detectable db2 process running is db2fcmd
I have not been able to find any instructions regarding LD_LIBRARY_PATH and LIBPATH for HP-UX. They are not mentioned in the installation guide at all. I cannot find it in any of the installation notes.   I presume sapinst is setting them itself before they are needed. Neither are set in the enviroment of db2<sid> or <sid>adm. I have gnawed my fingernails to the elbow over this one, but I cannot see any indication that either should be set for HP-UX. Anyway, they are definitely not set anywhere, to anything. This was a clean machine before I started chopping it up to do this install.
I figure it must be complicated - I have been trying to get an answer for 10 days already. I will absolutely hate myself when it turns out to be something obvious, documented in 10 places, mostly in bold italics. I shoulda taken my dads advice and been a riverboat gambler or a piano player in a cathouse - its a lot less complicated,

Unable to get a connection for pool - ResourceUnavailableException

Hi
I have a BPEL process which starts a child instance of another asynchronous BPEL process for each message in an XML file. The child BPEL process makes a call to the Oracle Apps JCA Adapter to push the data into E-Business Suite.
All works perfectly except when the number of messages exceeds a certain limit (15 or so). The error received is as follows:
"Exception occured when binding was invoked.
Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'SyncPersonRecord' failed due to:
JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection.
ebsPeoplesoftEmployees:SyncPersonRecord [ SyncPersonRecord_ptt::SyncPersonRecord(InputParameters,OutputParameters) ] :
The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue:
javax.resource.spi.ApplicationServerInternalException:
Unable to get a connection for pool = 'eis/Apps/Apps',
weblogic.common.resourcepool.ResourceUnavailableException:
No resources currently available in pool eis/Apps/Apps to allocate to applications.
Either specify a time period to wait for resources to become available, or increase the size of the pool and retry.. Please make sure that the JCA connection factory and any dependent connection factories have been configured with a sufficient limit for max connections.
Please also make sure that the physical connection to the backend EIS is available and the backend itself is accepting connections. ".
The invoked JCA adapter raised a resource exception.
Please examine the above error message carefully to determine a resolution."
Obviously what is happening is the connection pool maximum is reached (currently 15) and this is throwing the error.
What I need to do is to implement the suggestion of "specifying a time period to wait" and I was hoping someone could tell me how I do this?
I have tried setting the 'Connection Creation Retry Frequency' parameter to 30 seconds which made no difference and also have checked the documentation on "Configuring and Managing JDBC Data Sources for Oracle WebLogic Server".
Does anyone know if this is something that is implemented directly in the BPEL process/composite or in the connection source itself.
Many thanks

Open the jndi : eis/Apps/Apps in /console - config tab - increase the initial and max conn capacity and save it. Retry the scenario

Unable to get LaserJet M175nw to print over network

I have just installed a new LaserJet 100 Pro M175nw printer on my network. However I am unable to get it to print via the network.
The printer is connected to a ethernet cable and configured with a static IP address on the network
I am using a Windows 7 computer for printing
All internal functions of the printer work correctly e.g. copy, reports
Printing works when connected via USB to a computer
When using the printer via the network:
Scanning works correctly
The embedded web mangement page for the printer works correctly
The HP Print & Scan Doctor diagnostics give the configuration all green ticks
Print jobs stay in the print queue until they change to an error status.
The printer does not seem to recognise the print job at all - no progress message indicating printing document on the console
If the printer is in sleep mode it does not wake up
Test print pages from the HP Installer, from the Windows Printer Property dialog, from Acrobat Reader and from MS Word all fail.
All symptoms remain the same when I turn off the Windows Firewall
Another HP LaserJet 2605dn printer on the network prints correctly on a different IP address but also using the RAW format on port 9100.
I have removed all drivers for other HP printers in case there was a conflict - no change after re-installing the software.
Can anyone suggest what I might have overlooked? Thanks for your help.
This question was solved.
View Solution.

I am confused by your last statement, a TCP/IP is a network connection, which is why the universal print driver is suggested.
From what you have described, there is an issue with the print queue. Try running the Print and Scan Doctor :
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c03286146
Also, I am not sure if you tried the PCL6 driver or not, but I would like you to at least try it so that I know what its behavior is.
Let me know how that goes and I will get right back with you!
-Spencer

I am unable to get my Logitech T620 touch mouse to scroll horizontally in Photoshop CS6

I am unable to get my T620 touch mouse to scroll horizontally in Photoshop CS6. Any suggestions on how to enable this? The bar at the bottom of the document moves left/right as I scroll, but the screen doesn't.
I am using a T620 touch mouse on Windows 7 64 bit with the latest version of setpoint. I have checked the box in the mouses settings to allow sidescrolling with a swipe of 1 finger. I am aware you can hold control and swipe up/down to get a left right scroll.
Thanks in advance

This site may help.
How can I establish horizontal scroll with T620 To... - Logitech Forums
If this does not solve the problem, you may want to address your inquiry to the techs at that site.

I am unable to get a connection with my ipad through my router but I am able to get in when at my friend's house

I am unable to get a connection with my ipad with my wifi router. Will I need to upgrade my router

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Can I connect via HDMI and get 1920x1080?

Can I connect my MacBook Pro HDMI adapter up to my new Samsung Display via the HDMI connection and get 1920x1080? Or is the 1080p the best display I can do with that connection? Should I get the VGA adapter instead?

Not so fast please...
for HDMI rev 3.1 and above the AOK
However my SHARP 42" flat screen (model LC-42D72U) requires DVI MBP (adapter ) to DVI port on the SHARP.
I also have HDMI( and S video, component video and composite video) Also digital audio output from SHARP flat screen but for max UXGA resolution at horizontal frequency of 75.0 kHz DVI the way SHARP requires.
Fortunately Apple gave me DVI adapter free ( seldom heard nice four letter word )
"and a little help from my friends"...(apologies to the Beetles)
Let 'er rip and...
cheers

How do I get 1920x1080 from iMac7,1?

Current setup...
iMac7,1 connected to a Panasonic TCL42E50 using an Apple display port to VGA adaptor.
NOTE: I HAVE CONFIRMED IN THE USER MANUAL THAT THIS TV WILL DO 1920x1080
My iMac specs...
Mac OS X 10.7.4 (11E53)
Model Identifier:          iMac7,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
ATI,RadeonHD2600
I spent several hours on this and still can't get 1920x1080 res to display on my Panasonic 42". So is this an iMac problem? an adaptor problem? or TV problem? The Radeon 2600 graphics card is supposed to be able to display 1920x1080.
1920x1080 isn't an option.
I installed SwitchRezX and created a custom resolution and the highest it will accept is 1366x768. Anything higher than that, the Panasonic 42" won't accept the signal and the iMac display goes back to it's default res of 1680x1050.
I'd like to know if anyone who owns an iMac7,1 that has successfully output 1920x1080 and how you did it. I've heard everything from firmware issues in the Apple display adaptor to Apple blocking 1920x1080 on non-Apple displays (which I highly doubt Apple would do that) I just baught this adaptor so surely it's not a firmware issue.

Thanks for the link...was able to read up and learn the limits of a VGA connection.
So I think I understand the issue. After talking to Panasonic, they told me that my model only supports up to 1366x768 when using a VGA connection and they said to use the HDMI to get full 1080p quality. So, the user's manuel was misleading because it doesn't specify the limitations of the VGA port.
I'm still unsure if the iMac7,1 supports HDMI 1080p. I haven't been able to find an Apple mini-DVI to HDMI adaptor, but I did find an Apple mini-DVI to DVI adaptor that I could plug in a DVI to HDMI cable. Doing it this way I'm not sure if it would even be true 1080p even though the video card in the iMac7,1 can handle the resolution on a VGA connection. The apple specs say that the iMac7,1 supports external display via DVI up to 1920x1200 so if I converted that over to HDMI not sure if that would look right. I think I will shift my attention to my newer MacBook Pro which does suppot HDMI.
http://support.aple.com/kb/SP16
http://service.us.panasonic.com/OPERMANPDF/E-HELP_E50.PDF pg.33
Hope this helps anyone in the future.

Oracle.adf.controller.activity.ActivityLogicException: ADFC-02013: Unable to get metadata for activity

Hello,
I am new to ADF, I am trying to learn how to navigate from one page to another, the code that I have is simple, but it is not working, I specified the control flow rules in the adfc-config.xml and I even tried to specify the navigation rules in the faces-config.xml file, but it doesn't matter if I do it in one configuration file or another I get the same error. This is my first time working with ADF, I don't have formal training, just some video tutorial that I have seen on internet. I have previous experience with JSF, so I feel more comfortable writing the code for my program than using all the graphical tools (at least at this moment)
Any help to solve this problem will be highly appreciated.
This is my page1.jsf code:
<?xml version='1.0' encoding='UTF-8'?>
<!DOCTYPE html>
<f:view xmlns:f="http://java.sun.com/jsf/core" xmlns:af="http://xmlns.oracle.com/adf/faces/rich" xmlns:h="http://java.sun.com/jsf/html">
    <af:document title="page1.jsf" id="d1" binding="#{backingBeanScope.backing_page1.d1}">
        <af:form id="f1" binding="#{backingBeanScope.backing_page1.f1}"></af:form>
    </af:document>
    <h:head>
        <title>First JSF Example</title>
    </h:head>
    <h:body>
        <h3>ADF Hello World Example</h3>
        <h:form>
            What's your name?
            <h:inputText value="#{backingBeanScope.backing_page1.message}"></h:inputText>
            <h:commandButton value="Welcome Me" action="#{backingBeanScope.backing_page1.processPage1}"></h:commandButton>
        </h:form>
    </h:body>
</f:view>
This is my backing bean for page1:
package view.backing;
import oracle.adf.view.rich.component.rich.RichDocument;
import oracle.adf.view.rich.component.rich.RichForm;
public class Page1 {
    private RichForm f1;
    private RichDocument d1;
    private String message;
    public void setF1(RichForm f1) { this.f1 = f1; }
    public RichForm getF1() {return f1;}
     public void setD1(RichDocument d1) {this.d1 = d1;}
    public RichDocument getD1() {return d1;}
    public void setMessage(String msg) { this.message= msg; }
    public String getMessage() { return this.message; }
    public String processPage1()
        System.out.println("++++++++++++++++++++++++++++++++++++++++++++++move to next page");
        return "success";
This is my adfc-config.xml file:
<?xml version="1.0" encoding="UTF-8" ?>
<adfc-config xmlns="http://xmlns.oracle.com/adf/controller" version="1.2">
<control-flow-rule id="__5">
    <from-activity-id>page1.jsf</from-activity-id>
    <control-flow-case id="__6">
      <from-action>#{backingBeanScope.backing_page1.processPage1}</from-action>
      <from-outcome>success</from-outcome>
      <to-activity-id>page2.jsf</to-activity-id>
    </control-flow-case>
</control-flow-rule>
<managed-bean id="__2">
    <managed-bean-name>backing_page1</managed-bean-name>
    <managed-bean-class>view.backing.Page1</managed-bean-class>
    <managed-bean-scope>backingBean</managed-bean-scope>
    
</managed-bean>
<managed-bean id="__1">
    <managed-bean-name>backing_page2</managed-bean-name>
    <managed-bean-class>view.backing.Page2</managed-bean-class>
    <managed-bean-scope>backingBean</managed-bean-scope>
    
</managed-bean>
</adfc-config>
Finally this is my page2.jsf
<?xml version='1.0' encoding='UTF-8'?>
<!DOCTYPE html>
<f:view xmlns:f="http://java.sun.com/jsf/core" xmlns:af="http://xmlns.oracle.com/adf/faces/rich" xmlns:h="http://java.sun.com/jsf/html">
    <af:document title="page2.jsf" id="d1" binding="#{backingBeanScope.backing_page2.d1}">
        <af:form id="f1" binding="#{backingBeanScope.backing_page2.f1}"></af:form>
    </af:document>
    
    <h:body>
        <h3>ADF Hello World Example PAGE2</h3>
    </h:body>
</f:view>
This is the error that I get when I push the button on page1 and I try to navigate to page 2:
Target URL -- http://127.0.0.1:7101/EcatsADF12c-ViewController-context-root/faces/page1.jsf
<org.apache.myfaces.trinidadinternal.application.ViewHandlerImpl> <ViewHandlerImpl> <_checkTimestamp> <TIMESTAMP_CHECKING_ENABLED_SHOULDNOT_IN_PRODUCTION>
<Apr 22, 2015 4:34:43 PM CDT> <Warning> <Socket> <BEA-000449> <Closing the socket, as no data read from it on 127.0.0.1:57,015 during the configured idle timeout of 5 seconds.>
<Apr 22, 2015 4:34:43 PM CDT> <Warning> <Socket> <BEA-000449> <Closing the socket, as no data read from it on 127.0.0.1:57,014 during the configured idle timeout of 5 seconds.>
<Apr 22, 2015 4:34:43 PM CDT> <Warning> <Socket> <BEA-000449> <Closing the socket, as no data read from it on 127.0.0.1:57,013 during the configured idle timeout of 5 seconds.>
<Apr 22, 2015 4:34:43 PM CDT> <Warning> <Socket> <BEA-000449> <Closing the socket, as no data read from it on 127.0.0.1:57,017 during the configured idle timeout of 5 seconds.>
<Apr 22, 2015 4:34:43 PM CDT> <Warning> <Socket> <BEA-000449> <Closing the socket, as no data read from it on 127.0.0.1:57,016 during the configured idle timeout of 5 seconds.>
++++++++++++++++++++++++++++++++++++++++++++++move to next page
<oracle.dfw.impl.incident.DiagnosticsDataExtractorImpl> <DiagnosticsDataExtractorImpl> <createADRIncident> <incident 11 created with problem key "ADFC-02013 [ADFc]">
<oracle.dfw.impl.incident.DiagnosticsDataExtractorImpl> <DiagnosticsDataExtractorImpl> <createADRIncident> <incident 12 created with problem key "ADFC-02013 [ADFc]">
<oracle.adf.view> <RichExceptionHandler> <_logUnhandledException> <ADF_FACES-60098:Faces lifecycle receives unhandled exceptions in phase INVOKE_APPLICATION 5>
oracle.adf.controller.activity.ActivityLogicException: ADFC-02013: Unable to get metadata for activity 'page2.jsf'.
at oracle.adfinternal.controller.util.Utils.createAndLogActivityLogicException(Utils.java:234)
at oracle.adfinternal.controller.engine.ControlFlowEngine.doRouting(ControlFlowEngine.java:1133)
at oracle.adfinternal.controller.engine.ControlFlowEngine.doRouting(ControlFlowEngine.java:979)
at oracle.adfinternal.controller.engine.ControlFlowEngine.routeFromActivity(ControlFlowEngine.java:551)
at oracle.adfinternal.controller.engine.ControlFlowEngine.performControlFlow(ControlFlowEngine.java:162)
at oracle.adfinternal.controller.application.NavigationHandlerImpl.handleAdfcNavigation(NavigationHandlerImpl.java:119)
at oracle.adfinternal.controller.application.NavigationHandlerImpl.handleNavigation(NavigationHandlerImpl.java:88)
at org.apache.myfaces.trinidadinternal.application.NavigationHandlerImpl.handleNavigation(NavigationHandlerImpl.java:50)
at com.sun.faces.application.ActionListenerImpl.processAction(ActionListenerImpl.java:130)
at javax.faces.component.UICommand.broadcast(UICommand.java:315)
at javax.faces.component.UIViewRoot.broadcastEvents(UIViewRoot.java:794)
at javax.faces.component.UIViewRoot.processApplication(UIViewRoot.java:1259)
at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._invokeApplication(LifecycleImpl.java:1074)
at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._executePhase(LifecycleImpl.java:402)
at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:225)
at javax.faces.webapp.FacesServlet.service(FacesServlet.java:593)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:280)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:254)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:136)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:346)
at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:25)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:192)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at oracle.adfinternal.view.faces.webapp.rich.RegistrationFilter.doFilter(RegistrationFilter.java:105)
at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:502)
at oracle.adfinternal.view.faces.activedata.AdsFilter.doFilter(AdsFilter.java:60)
at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:502)
at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:327)
at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:229)
at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at oracle.adf.library.webapp.LibraryFilter.doFilter(LibraryFilter.java:202)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:137)
at java.security.AccessController.doPrivileged(Native Method)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:460)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:120)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:217)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:81)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:220)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:79)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3436)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3402)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
at weblogic.servlet.provider.WlsSubjectHandle.run(WlsSubjectHandle.java:57)
at weblogic.servlet.internal.WebAppServletContext.doSecuredExecute(WebAppServletContext.java:2285)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2201)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1572)
at weblogic.servlet.provider.ContainerSupportProviderImpl$WlsRequestExecutor.run(ContainerSupportProviderImpl.java:255)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:311)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:263)

User, tell us your jdev version, please!
What is your goal?
What you have find had nothing to do with ADF. If you ent to learn adf then I recommend to work through find of the tutorials available on the jdev home page.
If adf is not your goal, you might want to use Trinidad and ask your question in their forum.
You might not like the declarative approach adf uses, but if you want to learn how to use adf, you have to understand how ADF works. Most can be done using java, but one you understand the framework you see the advantage.
Timo

IFS-20010 Unable to get service configuration

Hi,
I'm trying to connect to iFS from a Java application. Basically it's a remote server which we'll connect to using RMI for some integration work. It will run on the same server as CM SDK.
Anyway, I try and connect to the service using:
LibraryService.startService(name, schemaPassword, serviceConfig, domainName)
and it comes back with this error:
oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefault)
oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (SmallServiceConfiguration)
java.lang.NullPointerException
at oracle.gss.util.NLSLocale.getNLSLanguage(NLSLocale.java:675)
I'm running it from the command line, I have a batch file to set the classpath. Interestingly, if I run an Agent (i.e., a java class that extends oracle.ifs.management.domain.IfsServer) standalone, it works fine.
This makes me think there's some element of the classpath that I'm missing, but I'm not entirely sure what!
Could anyone shed any light on this? Metalink doesn't seem to have anything!
Cheers,
Phill
P.S. -- my CLASSPATH is as follows:
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\ifs\cmsdk\lib\cmsdk.jar;%ORACLE_HOME%\lib;
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\jdbc\lib\classes12.zip;%ORACLE_HOME%\j2ee\home\lib;
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\j2ee\home\jazn.jar
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\jdbc\lib\nls_charset12.jar
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\ifs\cmsdk\settings\

Just FYI, the solution to this was that the java security policy was denying access. I changed the java.policy to
grant {
permission java.security.AllPermission;
And this solved the problem.

Unable to get 1920x1080 resolution [Solved]

Similar Messages

Maybe you are looking for