Unsigned Driver Install - No prompting

Hello,
I am building out approximately 160 print servers with around 9,000 print queues in total.  As you can imaging all of this needs to be automated as well as the backup/restore portions.  I am utilizing Windows 2012 R2 as the O/S.  When my script
runs to add unsigned INFs into the Driver store I receive a prompt warning me: "Windows can't verify the publisher of this driver software"
I can click through it and it will install the driver, however with the amount of queues and unsigned drivers I have to work with this is not ideal.  I have looked at some of the posts here and have done the following:
bcdedit -set loadoptions DDISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
AND
Modified group policy: User Configuration -> Administrative Templates -> System -> Driver Installation -> Code signing for device drivers.  Set to Enabled with setting Ignore
Does anyone know how to turn off the prompt and simply continue with signed and unsigned driver adds to the driver store?
Thanks for your help

Hi Xirg,
Please try to edit the following registry key to 0 (before you do this please backup the registry key first):
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Driver Signing\Policy
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Non-Driver Signing\Policy
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

  • Hi, I have a macbook pro with a new hard drive installed. My WD external drive backup on time machine now wont let me access the files. I get a prompt saying 'you do not have permission to access the files'

    hi, I have a macbook pro with a new hard drive installed and restored. My WD external drive backup on time machine now wont let me access the files. I get a prompt saying 'you do not have permission to access the files' After my new drive was installed I plugged in time machine and it started backing up. I paused it when I realised that it was running for more than a few minutes. I now realise that it probably started backing up the new hard drive all over again. Which makes me think that the original back up must be on the WD back I cant seem to access it. Any ideas would be helpful.

    See E-10 in the first link.
    Time Machine Troubleshooting
    Time Machine Troubleshooting Problems

  • How to install an unsigned driver in bootcamp Windows 8.1?

    I need to install an unsigned driver on my Windows 8.1 bootcamp partition, but it disables that by default. If I edit the boot options in the advanced options, then my mouse and keyboard (Ive tried many types) will not connect or work at all. Any ideas?

    Hi Willimo,
    The main issue is to install the graphic driver software ,right ?
    There are two ways to get the driver, automatically update from the windows update or manually download the driver from the manufacturer website and install it from the device manager.
    Please refer to the following link :
    Download and install drivers
    http://windows.microsoft.com/en-hk/windows-8/all-drivers
    Best regards
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • K7N2G will not load windows xp with any type of dvd/cd drive installed?

    This is on my old computer, the specs are as follows
    k7n2g
    athlon 2600+
    radeon 9700 pro
    Caviar SE wd800
    1gb samsung ddr333
     It does not matter if it is keyed as master or slave, primary or secondary my old k7n2g will not load windows with a cd drive installed. I have tried three different drives and everything that I can think of, changed cables, channels, drives, everything. Windows just hangs. I cannot even get into safe mode. Is this an IRQ problem? The drives keeps trying to eject themselves, no matter what kind I use. This has never happened before, but there was a point before this problem where the vga wouldn't kick on (at the login screen) until I hit eject on the cd drive. This is driving me crazy and I have a girlfriend who just has to play her stupid sims and will not stop bothering me about it. PLEASE PLEASE PLEASE help me!
    Thanks
    Chris
    PS here is my NEW workstation (I couldn't be happier to get rid of the old system)
    two Opteron 250 90nm
    2gb 2-3-2-6 Corsair Reg/ECC DDR 400
    Tyan Thunder K8WE
    1x BFG 7800GTX OC (one for now)
    Audigy 4 Pro
    Seagate Cheetah U160 10k 73.4 gb
    Atlas V U160 18.3 gb
    Lite on Dual Layer burner

    Your Tyan based hardware listing on the first post has no relevance to anything, and might only serve to confuse. Please remove it and put the hardware you are trying to troubleshoot in a signature. Look in your profile>Forum Profile Information and enter that in the Signature box. That way we wont have to scroll to hunt down your hardware specs
    So let us get this straight.
    This system used to work fine? Yes? Then what prompted you to reload the OS?
    You mentioned that didn't happen when you owned it. Are we to assume that at some point you sold or gave parts of this system to someone else? If so, what changed?
    A little more history might prove useful in helping us to give you better suggestions.
    Look at the PSU and give the Amps for the +3.3, +5v, & +12v lines.
    ***Edit, from what I see on the net, that is a dual rail PSU and the amps are as follows:
    +3.3V@22A, +5V@21A, +12V1@18A, +12V2@16A
    Is this correct?
    Both the 3.3 and +5v seem a little low to me, but I am not entirely convinced that would be your problem. However, the fact that the 12v rails are split, can lead to other problems such as overvoltage protection circuitry getting in the way. Especially if the 16amp 12v rail is overloaded.
    This is something to consider. Just because it is supposedly capable of wattage over it's rated power output doesn't mean it can handle what you're throwing at it all at once. If you have a single rail PSU that has at least 18 amps on the 12v rail to test with, we could almost definitively rule out power as the sole problem or a contributing factor.
    I have never had a CD rejected, but if you could be more detailed about what you have connected to the board while attempting to load the OS, and then a detailed description of at what point the OS installation fails, and the CD is ejected, that would be helpful as well.
    The fact that you've tried several drives, cables, with the same result. And also had a blackscreen event, does point to at least one problem that could point to a power issue. The CD rejection issue is foreign to me since I usually use the same type of PSU in all my builds or ones that I know work with a particular set of hardware, so I can't attribut that to a power issue.
    Did you try clearing the CMOS and then initialize the default settings?
    Do you have a cheap AGP card to try instead of the 9700?

  • Error running unsigned driver inventory and test

    I’m working a challenge where the cluster validation tool on a Server 2008 R2 SP1 based cluster throws an error running the unsigned driver inventory/validation. It doesn’t say that there are any unsigned
    drivers but rather says:
    An error occurred while executing the test.
    There was an error getting information about the unsigned drivers installed on the nodes.
    There was an error retrieving information about the Unsigned Drivers from node 'someclusternode.contoso.com'.
    Shutting down
    If we run the tool from other nodes it will always pass itself and 4 out of the 5 other nodes, but there will be one node that will trigger this. And the node that it fails on is not consistent.
    All of the other tests run just fine, and I can’t find anything in any KB that points me in a troubleshooting direction.

    Hi,
    Before you install the failover cluster you need confirm your hardware meet the Windows failover cluster hardware requirements. You can from the following website to confirm
    your server has been authenticated.
    Windows Sever Catalog:
    http://www.windowsservercatalog.com/
    More information:
    Failover Clustering Overview
    http://technet.microsoft.com/en-us/library/hh831579.aspx
    At same time some incompatible issue have found on the specified type of HP ProLiant® Server and the HP have already update the ACPI driver.
    HP has driver update for W2K8, specific for this ACPI-Compliant Power Meter Device Identifier
    http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&swItem=MTX-24c4d70d491b40628c0b73dd99&jumpid=reg_R1002_USEN
    More information:
    Implementing Microsoft® Windows Server® 2008 R2 on HP ProLiant servers
    http://h20000.www2.hp.com/bc/docs/support/SupportManual/c01639594/c01639594.pdf?jumpid=reg_R1002_USEN
    read under:
    Power Management Features
    -> Power Metering and Budgeting (PMB)
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • P505 Widnow 7 After Recovery, All Tosbiba HW driver report unsigned driver and no Window 7 Update

    Hello,
    I just clean up the HD and use the recovery media that created after I get the system to recover my wife's Satellite P505-S8980 system due to some virus causing the system problems. I recover the system to a brand new harddisk with all the default options. Window 7 recovered successfully.
    After the finial boot, the screen turn to lower resolutions and once login, I went to device manager report that the Video, Wifi, Ethernet and SD Card reader were all unsigned driver and do not able to start them. I then try to do F8 during reboot to bypass driver verification, window working just fine. But if I boot it normally, it will have problem with those drivers. I think also try to install newer driver from Support webstie, those driver have the same problem.
    I was trying to do a Window update, it always fail to update. How can it be fixed? Both driver problem and Window 7 update. I guess this problem must be linked.
    Mcken

    Satellite P505-S8980 
    ..use the recovery media that created after I get the system to recover
    I would do the very same thing again, that is, restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. (You can do it from the hard disk directly. See p. 62 in the User's Guide.)
    If the trouble occurs before making any changes, then there is almost certainly a hardware problem. To be sure,  you could reflash the BIOS.
    -Jerry

  • I did not deactivate a photoshop cs6 before there was a new hard drive installed with a Win7 Pro fresh install too. How can I activate photoshop on the new hardware if I can't deactivate it on the old hardware that is no longer available? Any help will be

    I did not deactivate a photoshop cs6 before there was a new "C" hard drive installed on my computer and a Win7 Pro fresh install too. How can I activate photoshop on the new hardware if I can't deactivate it on the old hardware that is no longer available? Any help will be appreciated.

    If it's the same machine (same CPU) there should not be any need to activate.  The actiovation is tied to your CPU.
    If you run into problems, then:
    Unfortunately, only Adobe customer service can assist you with your issue. These are user forums; you are not addressing Adobe here.
    Click on the link below, and after that click on "Still need Help? Contact us."
    Then on the next page, click Chat
    There is also a phone option. 1 (800) 833-6687
    http://helpx.adobe.com/contact.html?step=PHXS_downloading-installing-setting-up_licensing- activation

  • How to restore music on computer after new hard drive installed?

    had new hard drive installed and am not able to retrieve/find music that was backed up on my computer before new hard drive was installed.  Only music that was in the "cloud" was able to be retrieved. Any idea where it could be?
    Thanks!

    Did you reinstalled iTunes ? It looks like you had a newer version of iTunes with the corresponding database, and now your iTunes seem to be an older version. If you are a little patient, you might easily fix this with iTunes 10.5 which should come out very very soon since iOS 5 has been annonced for tomorrow.

  • I have an Epson printer on a Wifi network. Windows 7 desktop and and HP Win 7 laptop (my wifes) print to it just fine. My MacBook Pro running Yosemite won't detect it, and I have the latest driver installed. No problem when I had a Canon...

    I have an Epson printer on a Wifi network. Windows 7 desktop is running the network, and my wife's HP Win 7 laptop prints to it just fine. My MacBook Pro running Yosemite won't detect it, and I do have the latest driver installed. I didn't have a problem when I had a Canon Pixma on the network, but when I replaced it with the Epson nothing seems to work. I go to add a printer to the queue and only the FAX function of the printer shows up - not the WS-4530 print function. Does anyone out there have any suggestions?  Please??? :-)

    Hi Kelly,
    As someone who has to print from my Mac to a networked printer at home all the time, I can certainly understand how frustrating it must be to have that fail to perform as expected. Let's see if we can get you up and running.
    I would suggest that you troubleshoot using the steps in this article -
    OS X Yosemite: Printing troubleshooting
    Start with the section titled Check the network.
    Thanks for using Apple Support Communities.
    Sincerely,
    Brett L 

  • I had a new hard drive installed on my IMac.  Now I am trying to find my photos on time machine to restore on Iphoto.  How do you do this?

    I had a new hard drive installed on my IMac.  Now I am trying to reload everything back on.  I do have time machine.  How do I find all my pictures on TIme Machine to load back on IPhoto.  I hope I haven't lost all my family photos. Help!  Thanks a bunch!

    Hi, I never use TM, but...
    Have you looked through Pondini's extensive TM help site?
    http://Pondini.org/TM/FAQ.html
    http://pondini.org/TM/Troubleshooting.html
    Can't imaging something not being covered there.

  • I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you plea

    I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?

    You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
    Clean Install of Snow Leopard
    Be sure to make a backup first because the following procedure will erase
    the drive and everything on it.
         1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
             with your computer.  Insert the disc into the optical drive and restart the computer.
             After the chime press and hold down the  "C" key.  Release the key when you see
             a small spinning gear appear below the dark gray Apple logo.
         2. After the installer loads select your language and click on the Continue
             button. When the menu bar appears select Disk Utility from the Utilities menu.
             After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
             size.)  Click on the Partition tab in the DU main window.  Set the number of
             partitions to one (1) from the Partitions drop down menu, click on Options button
             and select GUID, click on OK, then set the format type to MacOS Extended
             (Journaled, if supported), then click on the Apply button.
         3. When the formatting has completed quit DU and return to the installer.  Proceed
             with the OS X installation and follow the directions included with the installer.
         4. When the installation has completed your computer will Restart into the Setup
             Assistant. After you finish Setup Assistant will complete the installation after which
             you will be running a fresh install of OS X.  You can now begin the update process
             by opening Software Update and installing all recommended updates to bring your
             installation current.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

  • Is it possible to get a 1TB hard drive installed into my Macbook Pro Retina?

    I am a photographer and I have a lot of photos and its hard to store them all.  I have a back up drive I currently have my iPhoto library on, but it crashes a lot.
    Can I get an internal drive installed? How much does this cost?

    Welcome to the Apple Support Communities
    The MacBook Pro with Retina display can only use flash storage because a hard disk doesn't fit onto this computer. Unfortunately, the only thing you can do is to store the photos onto an external disk, if they doesn't fit onto your flash storage.
    If your external disk is slow, you may want to buy a Thunderbolt external disk. It's much faster than a USB external disk and you shouldn't notice any problem anymore with it

  • My old iMac broke so i got a new hard drive installed. How can i retrieve my old purchased items?

    hiya
    got a new hard drive installed and couldn't retreive anything off my old hard drive
    can i get my old purchased items from itunes
    thanks

    Hi hopscotch,
    Log into the iTunes store and do a search to find your previously purchased items. Click the "Buy" button, and put in the same iTunes id and password that you originally used to purchase. A dialogue box will come up indicating that you have already purchased this item and do you want to download it again for free....
    Say yes, and it will be re-downloaded to your Mac.
    Hope this helps!
    Cheers,
    GB

  • A connection to the deployment share could not be made - Networking device did not have a driver installed

    I have a couple of HP 8200 desktops that I think might have bad nics. When I PXE boot them and start my LiteTouch, I get a Wizard error that says
    A connection to the deployment share (\\mydpshare\share) could not be made. The following networking device did not have a driver installed
    PCI\VEN_8086&DEV_1502&SUBSYS_1496103C&REV_04
    I have that driver in MDT and it works on other HP 8200s. Looking into the Wpeinit.log, it looks like the driver loads but maybe the nic is bad:
    Installing device root\kdnic X:\WINDOWS\INF\kdnic.inf succeeded
    Installing device pci\ven_8086&dev_1502  X:\WINDOWS\INF\net1ic64.inf succeeded
    Spent 16903ms installing network drivers
    QueryAdapterStatus:  no adapters found
    Spent 0ms confirming network initialization; status 0x80004005
    WaitForNetworkToInitialize failed; ignoring error
    Has anyone seen this before?
    Orange County District Attorney

    Hi,
    According to your description, it should be Intel NIC driver problem. I have checked HP official website, there is new NIC driver released, please access to the link below to download the NIC driver for test:
    http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5037932&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D2%257CswItem%253Dvc_111651_1%257CswEnvOID%253D4060%257CitemLocale%253D%257CswLang%253D%257Cmode%253D4%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken
    Roger Lu
    TechNet Community Support

  • HP Color Laserjet 2600n cant print on Win8 even with the right driver installed!

    I configured the HP Color Laserjet 2600n from TCP/IP port and dit the windows update on drives, installed my printer but it won't even print the test page. it says error printing on the print queue. I cheked the network and sharing. I checked the printer works perfectly on Win 7 but not on my hp Win8.

    Hello there,
    To get your issue more exposure, I would suggest posting it in the commercial forums since your product is a commercial product. You can do this at Commercial Forums - Printers - LaserJet.
    Enjoy your day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Maybe you are looking for